| Age | Commit message (Collapse) | Author |
|---|
|
The ADM1266 is a cascadable super sequencer with margin control and
fault recording.
This commit adds basic support for its PMBus commands and models
the identification registers that can be modified in a firmware
update.
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
[PMD: Cover file in MAINTAINERS]
Message-ID: <20231023-staging-pmbus-v3-v4-5-07a8cb7cd20a@google.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
|
|
We use the user_ss[] array to hold the user emulation sources,
and the softmmu_ss[] array to hold the system emulation ones.
Hold the latter in the 'system_ss[]' array for parity with user
emulation.
Mechanical change doing:
$ sed -i -e s/softmmu_ss/system_ss/g $(git grep -l softmmu_ss)
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20230613133347.82210-10-philmd@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
MAX31785 is a PMBus compliant 6-Channel fan controller. It supports 6 fan
channels, 11 temperature sensors, and 6-Channel ADC to measure the remote
voltages. Datasheet can be found here:
https://datasheets.maximintegrated.com/en/ds/MAX31785.pdf
This initial version of the driver has skeleton and support for the
fan channels. Requests for temperature sensors, and ADC Channels the
are serviced with the default values as per the datasheet. No additional
instrumentation is done. NV Log feature is not supported.
Signed-off-by: Maheswara Kurapati <quic_mkurapat@quicinc.com>
Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220627154703.148943-5-quic_jaehyoo@quicinc.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
|
|
Signed-off-by: Titus Rwantare <titusr@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Message-Id: <20220307200605.4001451-8-titusr@google.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
|
|
This commit adds emulation of the magnetometer on the LSM303DLHC.
It allows the magnetometer's X, Y and Z outputs to be set via the
mag-x, mag-y and mag-z properties, as well as the 12-bit
temperature output via the temperature property. Sensor can be
enabled with 'CONFIG_LSM303DLHC_MAG=y'.
Signed-off-by: Kevin Townsend <kevin.townsend@linaro.org>
Message-id: 20220130095032.35392-1-kevin.townsend@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
This contains some hardcoded register values that were obtained from the
hardware after reading the temperature.
It does enough to test the Linux kernel driver. The FIFO mode, IRQs and
operation modes other than the default as used by Linux are not modelled.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210616073358.750472-2-joel@jms.id.au>
[ clg: - Fixed sequential reading
- Reworked regs_reset_state array
- Moved model under hw/sensor/ ]
Message-Id: <20210629142336.750058-4-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
|
|
The MAX34451 is a Maxim power-supply system manager that can monitor up to 16 voltage rails or currents. It also contains a temperature sensor and supports up to four external temperature sensors.
This commit adds support for interfacing with it, and setting limits on the supported sensors.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-5-titusr@google.com>
[Moved the device to the sensor directory]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
The ADM1272 is a PMBus compliant Hot Swap Controller and Digital Power
Monitor by Analog Devices.
This commit adds support for interfacing with it, and support for
setting and monitoring sensor limits.
Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1272.pdf
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-3-titusr@google.com>
[Moved the device to the sensor directory]
[remove include of trace.h, it is not needed]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
Lots of this are expected to be coming in, create a directory for them.
Also move the tmp105.h file into the include directory where it
should be.
Cc: Cédric Le Goater <clg@kaod.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Andrew Jeffery <andrew@aj.id.au>
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: qemu-arm@nongnu.org
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Cédric Le Goater <clg@kaod.org>
|
