| Age | Commit message (Collapse) | Author |
|---|
|
Cc: qemu-ppc@nongnu.org
Signed-off-by: Richard Henderson <rth@twiddle.net>
Message-id: 1410626734-3804-22-git-send-email-rth@twiddle.net
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The device endianness is the cpu endianness at device reset time.
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Decimal Floating Point is emulated, so add it the mask. This will
fix the erroneous message:
Warning: Disabling some instructions which are not emulated by TCG (0x0, 0x4)
Signed-off-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This adds handling of the RESOURCE_ADDR_TRANS_MODE resource from
the H_SET_MODE, for POWER8 (PowerISA 2.07) only.
This defines AIL flags for LPCR special register.
This changes @excp_prefix according to the mode, takes effect in TCG.
This turns support of a new capability PPC2_ISA207S flag for TCG.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
POWER8 supports Event-Based Branch Facility (EBB). It is controlled via
set of SPRs access to which should generate an "Facility Unavailable"
interrupt if the facilities are not enabled in FSCR for problem state.
This adds EBB SPRs.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This adds migration support for registers saved before Transactional
Memory (TM) transaction started.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This adds TM (Transactional Memory) SPRs.
This adds generic spr_read_prev_upper32()/spr_write_prev_upper32() to
handle upper half SPRs such as TEXASRU which is upper half of TEXASR.
Since this is not the only register like that and their numbers go
consequently, it makes sense to generalize the helpers.
This adds a gen_msr_facility_check() helper which purpose is to generate
the Facility Unavailable exception if the facility is disabled.
It is a copy of gen_fscr_facility_check() but it checks for enabled
facility in MSR rather than FSCR/HFSCR. It still sets the interrupt cause
in FSCR/HFSCR (whichever is passed to the helper).
This adds spr_read_tm/spr_write_tm/spr_read_tm_upper32/spr_write_tm_upper32
which are used for TM SPRs.
This adds TM-relates MSR bits definitions. This enables TM in POWER8 CPU class'
msr_mask.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This adds POWER8 specific PMU MMCR2/MMCRS SPRs.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This adds an FSCR (Facility Status and Control Register) SPR. This defines
names for FSCR bits.
This defines new exception type - POWERPC_EXCP_FU - "facility unavailable" (FU).
This registers an interrupt vector for it at 0xF60 as PowerISA defines.
This adds a TCG helper_fscr_facility_check() helper to raise an exception
if the facility is not enabled. It updates the interrupt cause field
in FSCR. This adds a TCG translation block generation code. The helper
may be used for HFSCR too as it has the same format.
The helper raising FU exceptions is not used by this patch but will be
in the next ones.
This adds gen_update_current_nip() to update NIP in DisasContext.
This helper is not used now and will be called before checking for
a condition for throwing an FU exception.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This adds TIR (Thread Identification Register) SPR first defined for server
CPUs in PowerISA 2.07.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Previously LPCR was registered for the 970 class which was wrong as
it does not have LPCR. Instead, HID4 is used which this patch registers.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Compared to PowerISA-compliant CPUs, 970 family has most of them plus
PMC7/8 which are only present on 970 but not on POWER5 and later CPUs.
Since we are changing SPRs for Book3s/970 families, let's add them too.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Since we started adding "POWER" prefix to 64bit PMU SPRs, let's finish
the transition and fix MMCRA and define a supermode version of it.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This stops using 7xx common SPRs init function and adds separate set
of helpers for 970.
This does not copy ICTC SPR as neither 970 manual nor PowerISA mention it.
This defines 970/book3s PMU SPRs constants as they differs from the ones
used for 7XX.
This creates 2 helpers for PMU SPRs, one for supermode privileged SPRs and
one for user privileged SPRs as "sup" versions can be shared across
the family while "user" versions will behave different starting POWER8
(which will be addressed later).
This allows writing to Uxxxx SPRs from supermode. spr_write_ureg() is
implemented for this as a copy of already existing spr_read_ureg().
This allows writing to supervisor's SIAR - it used to be disabled
when gen_spr_7xx() was used.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The differences between classes were:
1. SLB size, was 32 for 970 and 64 for others, should be 64 for all;
2. check_pow() callback, HID0 format is the same so should be the same
0x01C00000 which means "deep nap", "doze" and "nap" bits set;
3. LPCR - 970 does not have it but 970MP had one (by mistake).
This fixes wrong differences and makes one 970 class.
This fixes wrong registration of LPCR which is not present on 970.
This defines HID0 bits and uses them in check_pow_970().
This does not copy MSR_SHV (Hypervisor State, HV) bit from 970FX to
970 class as we do not emulate hypervisor in QEMU anyway.
This does not remove check_pow_970FX now as it is still used by POWER5+
class, this will be addressed later.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
As defined in Linux kernel, PMC*, SIAR, MMCR0/1 have different numbers
for 32 and 64 bit POWERPC. We are going to support 64bit versions too so
let's rename 32bit ones to avoid confusion.
This is a mechanical patch so it does not fix obvious mistake with these
registers in POWER7 yet, this will be fixed later.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Today we have a lot of conditional code in the SPE emulation depending on
whether we have 64bit GPRs or not.
Unfortunately the assumption that we can just recycle the 64bit GPR
implementation is wrong. Normal SPE implementations maintain the upper 32 bits
on all non-SPE instructions which then only modify the low 32 bits. However
all instructions we model that adhere to the normal SF based switching don't
care whether they operate on 32 or 64 bit registers and just always use the full
64 bits.
So let's remove that dubious SPE optimization and revert everything to the same
code path the 32bit target code was taking. That way we get rid of differences
between the two implementations, but will get a slight performance hit when
emulating SPE instructions.
This fixes SPE emulation with qemu-system-ppc64 for me.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This puts a limit to the number of threads per core based on the current
compatibility mode. Although PowerISA specs do not specify the maximum
threads per core number, the linux guest still expects that
PowerISA2.05-compatible CPU supports only 2 threads per core as this
is what POWER6 (2.05 compliant CPU) implements, the same is for
POWER7 (2.06, 4 threads) and POWER8 (2.07, 8 threads).
This calls spapr_fixup_cpu_smt_dt() with the maximum allowed number of
threads which affects ibm,ppc-interrupt-server#s and
ibm,ppc-interrupt-gserver#s properties.
The number of CPU nodesremains unchanged.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This adds basic support for the "compat" CPU option. By specifying
the compat property, the user can manually switch guest CPU mode from
"raw" to "architected".
This defines feature disable bits which are not used yet as, for example,
PowerISA 2.07 says if 2.06 mode is selected, the TM bit does not matter -
transactional memory (TM) will be disabled because 2.06 does not define
it at all. The same is true for VSX and 2.05 mode. So just setting a mode
must be ok.
This does not change the existing behavior as the actual compatibility
mode support is coming in next patches.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
[agraf: fix compilation on 32bit hosts]
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
There are 2 L1 cache control registers - one for data (L1CSR0) and
one for instructions (L1CSR1).
Emulate both of them well enough to give the guest the illusion that
it could actually do anything about its caches.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
In addition to the L1 data cache configuration register L1CFG0 there is
also another one for the L1 instruction cache called L1CFG1.
Emulate that one with the same values as the data one.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
We're missing SPR definitions for GIVORs. Add them to the list of SPRs.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
On the x86, some devices need access to the CPU reset pin (INIT#).
Provide a generic service to do this, using one of the internal
cpu_interrupt targets. Generalize the PPC-specific code for
CPU_INTERRUPT_RESET to other targets.
Since PPC does not support migration across QEMU versions (its
machine types are not versioned yet), I picked the value that
is used on x86, CPU_INTERRUPT_TGT_INT_1. Consequently, TGT_INT_2
and TGT_INT_3 are shifted down by one while keeping their value.
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
There are 3 different variants of the decrementor for BookE and BookS.
The BookE variant sets TSR[DIS] to 1 when the DEC value becomes 1 or 0. TSR[DIS]
is then the indicator whether the decrementor interrupt line is asserted or not.
The old BookS variant treats DEC as an edge interrupt that gets triggered when
the DEC value's top bit turns 1 from 0.
The new BookS variant maintains the assertion bit inside DEC itself. Whenever
the DEC value becomes negative (top bit set) the DEC interrupt line is asserted.
So far we implemented mostly the old BookS variant. Let's do them all properly.
This fixes booting pseries ppc64 guest images in TCG mode for me.
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This flag will be used to decide whether to emulate some bits of
H_SET_MODE hypercall because some are POWER8-only.
While we are here, add 2.05 flag to POWER8 family too. POWER7/7+ already
have it.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
This resets SPR values to defaults on CPU reset. This should help
with little-endian guests reboot issues.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Note that while such functions may exist both for *-user and softmmu,
only *-user uses the CPUState hook, while softmmu reuses the prototype
for calling it directly.
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Default to false.
Tidy variable naming and inline cast uses while at it.
Tested-by: Jia Liu <proljc@gmail.com> (or32)
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Normally CPUState::cpu_index is used to pick the right CPU for various
operations. However default consecutive numbering does not always work
for POWERPC.
These indexes are reflected in /proc/device-tree/cpus/PowerPC,POWER7@XX
and used to call KVM VCPU's ioctls. In order to achieve this,
kvmppc_fixup_cpu() was introduced. Roughly speaking, it multiplies
cpu_index by the number of threads per core.
This approach has disadvantages such as:
1. NUMA configuration stays broken after the fixup;
2. CPU-targeted commands from the QEMU Monitor do not work properly as
CPU indexes have been fixed and there is no clear way for the user to
know what the new CPU indexes are.
This introduces a @cpu_dt_id field in the CPUPPCState struct which
is initialized from @cpu_index by default and can be fixed later
to meet the device tree requirements.
This adds an API to handle @cpu_dt_id.
This removes kvmppc_fixup_cpu() as it is not more needed, @cpu_dt_id
is calculated in ppc_cpu_realize().
This will be used later in machine code.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Acked-by: Mike Day <ncmike@ncultra.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Correctly update the htab_mask using the return value of
KVM_PPC_ALLOCATE_HTAB ioctl. Also we don't update sdr1
on GET_SREGS for HV. We check for external htab and if
found true, we don't need to update sdr1
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[ fixed pte group offset computation in ppc_hash64_htab_lookup() that
caused TCG to fail, Greg Kurz <gkurz@linux.vnet.ibm.com> ]
Signed-off-by: Greg Kurz <gkurz@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This patch updates the ppc_avr_t data structure to include elements for
signed 64-bit integers and (conditionally) unsigned 128 bit integers.
These elements will be in instructions models later on in this patch series.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This patch adds a flag that will be used to tag the Altivec instructions
introduced in Power ISA Version 2.07.
The flag is added to Power8 model since P8 supports these instructions.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This patch adds the Load Quadword and Reserve (lqarx) instruction,
which is new in Power ISA 2.07.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This patch adds a flag to identify the load/store quadword instructions
that are introduced with Power ISA 2.07.
The flag is added to the Power8 model since P8 supports these
instructions.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This patch adds support for the Target Address Register (TAR) to the Power8
model.
Because supported SPRs are typically identified in an init_proc_*()
function and because the Power8 model is currently just using the
init_proc_POWER7() function, a new init_proc_POWER8() function
is added and plugged into the P8 model.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This patch adds a flag for the bctar instruction. This instruction
is being introduced via Power ISA 2.07.
Also, the flag is added to the Power8 machine model since the P8
processor supports this instruction.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This patch adds a flag for Floating Point Test instructions that were
introduced in Power ISA V2.06B.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This patch adds a flag for the floating point conversion instructions
introduced in Power ISA 2.06B.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This patch adds a flag for the atomic instructions introduced
in Power ISA V2.06B.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This patch adds a flag for the Divide Extended instructions that
were introduced in Power ISA V2.06B. The flag is added to the
Power7 and Power8 models.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This patch adds the Bit Permute Doubleword (bpermd) instruction,
which was introduced in Power ISA 2.06 as part of the base 64-bit
architecture.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This patch adds a flag to identify those VSX instructions that are
new to Power ISA V2.07. The flag is added to the Power 8 processor
initialization so that the P8 models understand how to decode and
emulate instructions in this category.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Assuming that "U" in SPR_UCTRL is for "user", there is inconsistency with
970 user manuals/P5-bookIV/PowerISA204 which define the number as:
priviledged
# spr5-9 spr0-4 name mtspr mfspr len cat
136 00100 01000 CTRL - no 32 S
152 00100 11000 CTRL yes - 32 S
This swaps the numbers. No effect from this change is expected though.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
PowerISA defines LPCR SPR number as 318=0x13E but QEMU uses the value of
316.
This fixes the definition of LPCR SPR.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This patch adds support for the VSX bit of the PowerPC Machine
State Register (MSR) as well as the corresponding VSX Unavailable
exception.
The VSX bit is added to the defined bits masks of the Power7 and
Power8 CPU models.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This patch adds the flag POWERPC_FLAG_VSX to the list of defined
flags and also adds this flag to the list of supported features of
the Power7 and Power8 CPUs. Additionally, the VSX instructions
are added to the list of TCG-enabled instruction.
Signed-off-by: Tom Musta <tommusta@gmail.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
Instead of opencoding 64 use MAX_SLB_ENTRIES. We don't update the kernel
header here.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
On POWER7, LPCR_ILE is used to control what endian guests take
their exceptions in so use it instead of MSR_ILE.
Signed-off-by: Anton Blanchard <anton@samba.org>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
The savevm code for the powerpc cpu emulation is currently based around
the old register_savevm() rather than register_vmstate() method. It's also
rather broken, missing some important state on some CPU models.
This patch completely rewrites the savevm for target-ppc, using the new
VMStateDescription approach. Exactly what needs to be saved in what
configurations has been more carefully examined, too. This introduces a
new version (5) of the cpu save format. The old load function is retained
to support version 4 images.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-id: 1374175984-8930-2-git-send-email-aliguori@us.ibm.com
[aik: ppc cpu savevm convertion fixed to use PowerPCCPU instead of CPUPPCState]
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
