| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Kenneth Heitke <kenneth.heitke@intel.com>
Reviewed-by: Klaus Birkelund Jensen <klaus.jensen@cnexlabs.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
Callback-based laio_submit() and laio_cancel() were left after
rewriting Linux AIO backend to coroutines in hope that they would be
used in other code that could bypass coroutines. They can be safely
removed because they have not been used since that time.
Signed-off-by: Julia Suvorova <jusual@mail.ru>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
drv_co_block_status digs bs->file for additional, more accurate search
for hole inside region, reported as DATA by bs since 5daa74a6ebc.
This accuracy is not free: assume we have qcow2 disk. Actually, qcow2
knows, where are holes and where is data. But every block_status
request calls lseek additionally. Assume a big disk, full of
data, in any iterative copying block job (or img convert) we'll call
lseek(HOLE) on every iteration, and each of these lseeks will have to
iterate through all metadata up to the end of file. It's obviously
ineffective behavior. And for many scenarios we don't need this lseek
at all.
However, lseek is needed when we have metadata-preallocated image.
So, let's detect metadata-preallocation case and don't dig qcow2's
protocol file in other cases.
The idea is to compare allocation size in POV of filesystem with
allocations size in POV of Qcow2 (by refcounts). If allocation in fs is
significantly lower, consider it as metadata-preallocation case.
102 iotest changed, as our detector can't detect shrinked file as
metadata-preallocation, which don't seem to be wrong, as with metadata
preallocation we always have valid file length.
Two other iotests have a slight change in their QMP output sequence:
Active 'block-commit' returns earlier because the job coroutine yields
earlier on a blocking operation. This operation is loading the refcount
blocks in qcow2_detect_metadata_preallocation().
Suggested-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
Commit b2fc91db8447 ("q35: set split kernel irqchip as default") changed
the default for the pc-q35-4.0 machine type to use split irqchip, which
turned out to have disasterous effects on vfio-pci INTx support. KVM
resampling irqfds are registered for handling these interrupts, but
these are non-functional in split irqchip mode. We can't simply test
for split irqchip in QEMU as userspace handling of this interrupt is a
significant performance regression versus KVM handling (GeForce GPUs
assigned to Windows VMs are non-functional without forcing MSI mode or
re-enabling kernel irqchip).
The resolution is to revert the change in default irqchip mode in the
pc-q35-4.1 machine and create a pc-q35-4.0.1 machine for the 4.0-stable
branch. The qemu-q35-4.0 machine type should not be used in vfio-pci
configurations for devices requiring legacy INTx support without
explicitly modifying the VM configuration to use kernel irqchip.
Link: https://bugs.launchpad.net/qemu/+bug/1826422
Fixes: b2fc91db8447 ("q35: set split kernel irqchip as default")
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Message-Id: <155786484688.13873.6037015630912983760.stgit@gimli.home>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
It's never used anywhere.
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Message-Id: <20190520030839.6795-5-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
In order to perform a valid migration of a vhost-scsi device,
the following requirements must be met:
(1) The virtio-scsi device state needs to be saved & loaded.
(2) The vhost backend must be stopped before virtio-scsi device state
is saved:
(2.1) Sync vhost backend state to virtio-scsi device state.
(2.2) No further I/O requests are made by vhost backend to target
SCSI device.
(2.3) No further guest memory access takes place after VM is stopped.
(3) Requests in-flight to target SCSI device are completed before
migration handover.
(4) Target SCSI device state needs to be saved & loaded into the
destination host target SCSI device.
Previous commit ("vhost-scsi: Add VMState descriptor")
add support to save & load the device state using VMState.
This meets requirement (1).
When VM is stopped by migration thread (On Pre-Copy complete), the
following code path is executed:
migration_completion() -> vm_stop_force_state() -> vm_stop() ->
do_vm_stop().
do_vm_stop() calls first pause_all_vcpus() which pause all guest
vCPUs and then call vm_state_notify().
In case of vhost-scsi device, this will lead to the following code path
to be executed:
vm_state_notify() -> virtio_vmstate_change() ->
virtio_set_status() -> vhost_scsi_set_status() -> vhost_scsi_stop().
vhost_scsi_stop() then calls vhost_scsi_clear_endpoint() and
vhost_scsi_common_stop().
vhost_scsi_clear_endpoint() sends VHOST_SCSI_CLEAR_ENDPOINT ioctl to
vhost backend which will reach kernel's vhost_scsi_clear_endpoint()
which process all pending I/O requests and wait for them to complete
(vhost_scsi_flush()). This meets requirement (3).
vhost_scsi_common_stop() will stop the vhost backend.
As part of this stop, dirty-bitmap is synced and vhost backend state is
synced with virtio-scsi device state. As at this point guest vCPUs are
already paused, this meets requirement (2).
At this point we are left with requirement (4) which is target SCSI
device specific and therefore cannot be done by QEMU. Which is the main
reason why vhost-scsi adds a migration blocker.
However, as this can be handled either by an external orchestrator or
by using shared-storage (i.e. iSCSI), there is no reason to limit the
orchestrator from being able to explictly specify it wish to enable
migration even when VM have a vhost-scsi device.
Considering all the above, this commit allows orchestrator to explictly
specify that it is responsbile for taking care of requirement (4) and
therefore vhost-scsi should not add a migration blocker.
Reviewed-by: Nir Weiner <nir.weiner@oracle.com>
Reviewed-by: Bijan Mottahedeh <bijan.mottahedeh@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Message-Id: <20190416125912.44001-4-liran.alon@oracle.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
into staging
ppc patch queue 2019-05-29
Next pull request against qemu-4.1. Highlights:
* KVM accelerated support for the XIVE interrupt controller in PAPR
guests
* A number of TCG vector fixes
* Fixes for the PReP / 40p machine
* Improvements to make check-tcg test coverage
Other than that it's just a bunch of assorted fixes, cleanups and
minor improvements.
This supersedes both the pull request dated 2019-05-21 and the one
dated 2019-05-22. I've dropped one hunk which I think may have caused
the check-tcg failure that Peter saw (by enabling the ppc64abi32
build, which I think has been broken for ages). I'm not entirely
certain, since I haven't reproduced exactly the same failure.
# gpg: Signature made Wed 29 May 2019 07:49:04 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-4.1-20190529: (44 commits)
ppc/pnv: add dummy XSCOM registers for PRD initialization
ppc/pnv: introduce new skiboot platform properties
spapr: Don't migrate the hpt_maxpagesize cap to older machine types
spapr: change default interrupt mode to 'dual'
spapr/xive: fix multiple resets when using the 'dual' interrupt mode
docs: provide documentation on the POWER9 XIVE interrupt controller
spapr/irq: add KVM support to the 'dual' machine
ppc/xics: fix irq priority in ics_set_irq_type()
spapr/irq: initialize the IRQ device only once
spapr/irq: introduce a spapr_irq_init_device() helper
spapr: check for the activation of the KVM IRQ device
spapr: introduce routines to delete the KVM IRQ device
sysbus: add a sysbus_mmio_unmap() helper
spapr/xive: activate KVM support
spapr/xive: add migration support for KVM
spapr/xive: introduce a VM state change handler
spapr/xive: add state synchronization with KVM
spapr/xive: add hcall support when under KVM
spapr/xive: add KVM support
spapr: Print out extra hints when CAS negotiation of interrupt mode fails
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
into staging
vga: add vhost-user-gpu.
# gpg: Signature made Wed 29 May 2019 05:40:02 BST
# gpg: using RSA key 4CB6D8EED3E87138
# gpg: Good signature from "Gerd Hoffmann (work) <kraxel@redhat.com>" [full]
# gpg: aka "Gerd Hoffmann <gerd@kraxel.org>" [full]
# gpg: aka "Gerd Hoffmann (private) <kraxel@gmail.com>" [full]
# Primary key fingerprint: A032 8CFF B93A 17A7 9901 FE7D 4CB6 D8EE D3E8 7138
* remotes/kraxel/tags/vga-20190529-pull-request:
hw/display: add vhost-user-vga & gpu-pci
virtio-gpu: split virtio-gpu-pci & virtio-vga
virtio-gpu: split virtio-gpu, introduce virtio-gpu-base
spice-app: fix running when !CONFIG_OPENGL
contrib: add vhost-user-gpu
util: compile drm.o on posix
virtio-gpu: add a pixman helper header
virtio-gpu: add bswap helpers header
vhost-user: add vhost_user_gpu_set_socket()
virtio-gpu: add sanity check
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The is_bridge field in PCIDevice acts as a bool, but is declared as an int.
Declare it as a bool for clarity, and change everything that writes it to
use true/false instead of 0/1 to match.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20190513061939.3464-5-david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Since c2077e2c "pci: Adjust PCI config limit based on bus topology",
pci_adjust_config_limit() has been used in the config space read and write
paths to only permit access to extended config space on buses which permit
it. Specifically it prevents access on devices below a vanilla-PCI bus via
some combination of bridges, even if both the host bridge and the device
itself are PCI-E.
It accomplishes this with a somewhat complex call up the chain of bridges
to see if any of them prohibit extended config space access. This is
overly complex, since we can always know if the bus will support such
access at the point it is constructed.
This patch simplifies the test by using a flag in the PCIBus instance
indicating whether extended configuration space is accessible. It is
false for vanilla PCI buses. For PCI-E buses, it is true for root
buses and equal to the parent bus's's capability otherwise.
For the special case of sPAPR's paravirtualized PCI root bus, which
acts mostly like vanilla PCI, but does allow extended config space
access, we override the default value of the flag from the host bridge
code.
This should cause no behavioural change.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Message-Id: <20190513061939.3464-4-david@gibson.dropbear.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
build_append_foo() API doesn't need explicit endianness conversions
which eliminates a source of errors and it makes build_mcfg() look like
declarative definition of MCFG table in ACPI spec, which makes it easy
to review.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
v3:
* add some comment on the Configuration Space base address allocation
structure
v2:
* miss the reserved[8] of MCFG in last version, add it back
* drop SOBs and make sure bios-tables-test all OK
Message-Id: <20190521062836.6541-3-richardw.yang@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Now we have two identical build_mcfg functions.
Consolidate them in acpi/pci.c.
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
v4:
* ACPI_PCI depends on both ACPI and PCI
* rebase on latest master, adjust arm Kconfig
v3:
* adjust changelog based on Igor's suggestion
Message-Id: <20190521062836.6541-2-richardw.yang@linux.intel.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Add new virtio-gpu devices with a "vhost-user" property. The
associated vhost-user backend is used to handle the virtio rings and
provide rendering results thanks to the vhost-user-gpu protocol.
Example usage:
-object vhost-user-backend,id=vug,cmd="./vhost-user-gpu"
-device vhost-user-vga,vhost-user=vug
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190524130946.31736-10-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Add a base class that is common to virtio-gpu and vhost-user-gpu
devices.
The VirtIOGPUBase base class provides common functionalities necessary
for both virtio-gpu and vhost-user-gpu:
- common configuration (max-outputs, initial resolution, flags)
- virtio device initialization, including queue setup
- device pre-conditions checks (iommu)
- migration blocker
- virtio device callbacks
- hooking up to qemu display subsystem
- a few common helper functions to reset the device, retrieve display
informations
- a class callback to unblock the rendering (for GL updates)
What is left to the virtio-gpu subdevice to take care of, in short,
are all the virtio queues handling, command processing and migration.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190524130946.31736-8-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
This will allow to share the format conversion function with
vhost-user-gpu.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190524130946.31736-4-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
The helper functions are useful to build the vhost-user-gpu backend.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190524130946.31736-3-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Add a new vhost-user message to give a unix socket to a vhost-user
backend for GPU display updates.
Back when I started that work, I added a new GPU channel because the
vhost-user protocol wasn't bidirectional. Since then, there is a
vhost-user-slave channel for the slave to send requests to the master.
We could extend it with GPU messages. However, the GPU protocol is
quite orthogonal to vhost-user, thus I chose to have a new dedicated
channel.
See vhost-user-gpu.rst for the protocol details.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 20190524130946.31736-2-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Commit 0b8c89be7f7b added the hpt_maxpagesize capability to the migration
stream. This is okay for new machine types but it breaks backward migration
to older QEMUs, which don't expect the extra subsection.
Add a compatibility boolean flag to the sPAPR machine class and use it to
skip migration of the capability for machine types 4.0 and older. This
fixes migration to an older QEMU. Note that the destination will emit a
warning:
qemu-system-ppc64: warning: cap-hpt-max-page-size lower level (16) in incoming stream than on destination (24)
This is expected and harmless though. It is okay to migrate from a lower
HPT maximum page size (64k) to a greater one (16M).
Fixes: 0b8c89be7f7b "spapr: Add forgotten capability to migration stream"
Based-on: <20190522074016.10521-3-clg@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155853262675.1158324.17301777846476373459.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The interrupt mode is chosen by the CAS negotiation process and
activated after a reset to take into account the required changes in
the machine. This brings new constraints on how the associated KVM IRQ
device is initialized.
Currently, each model takes care of the initialization of the KVM
device in their realize method but this is not possible anymore as the
initialization needs to be done globaly when the interrupt mode is
known, i.e. when machine is reseted. It also means that we need a way
to delete a KVM device when another mode is chosen.
Also, to support migration, the QEMU objects holding the state to
transfer should always be available but not necessarily activated.
The overall approach of this proposal is to initialize both interrupt
mode at the QEMU level to keep the IRQ number space in sync and to
allow switching from one mode to another. For the KVM side of things,
the whole initialization of the KVM device, sources and presenters, is
grouped in a single routine. The XICS and XIVE sPAPR IRQ reset
handlers are modified accordingly to handle the init and the delete
sequences of the KVM device.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-15-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Add a check to make sure that the routine initializing the emulated
IRQ device is called once. We don't have much to test on the XICS
side, so we introduce a 'init' boolean under ICSState.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190513084245.25755-13-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The way the XICS and the XIVE devices are initialized follows the same
pattern. First, try to connect to the KVM device and if not possible
fallback on the emulated device, unless a kernel_irqchip is required.
The spapr_irq_init_device() routine implements this sequence in
generic way using new sPAPR IRQ handlers ->init_emu() and ->init_kvm().
The XIVE init sequence is moved under the associated sPAPR IRQ
->init() handler. This will change again when KVM support is added for
the dual interrupt mode.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-12-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
If a new interrupt mode is chosen by CAS, the machine generates a
reset to reconfigure. At this point, the connection with the previous
KVM device needs to be closed and a new connection needs to opened
with the KVM device operating the chosen interrupt mode.
New routines are introduced to destroy the XICS and the XIVE KVM
devices. They make use of a new KVM device ioctl which destroys the
device and also disconnects the IRQ presenters from the vCPUs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This will be used to remove the MMIO regions of the POWER9 XIVE
interrupt controller when the sPAPR machine is reseted.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
When the VM is stopped, the VM state handler stabilizes the XIVE IC
and marks the EQ pages dirty. These are then transferred to destination
before the transfer of the device vmstates starts.
The SpaprXive interrupt controller model captures the XIVE internal
tables, EAT and ENDT and the XiveTCTX model does the same for the
thread interrupt context registers.
At restart, the SpaprXive 'post_load' method restores all the XIVE
states. It is called by the sPAPR machine 'post_load' method, when all
XIVE states have been transferred and loaded.
Finally, the source states are restored in the VM change state handler
when the machine reaches the running state.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This handler is in charge of stabilizing the flow of event notifications
in the XIVE controller before migrating a guest. This is a requirement
before transferring the guest EQ pages to a destination.
When the VM is stopped, the handler sets the source PQs to PENDING to
stop the flow of events and to possibly catch a triggered interrupt
occuring while the VM is stopped. Their previous state is saved. The
XIVE controller is then synced through KVM to flush any in-flight
event notification and to stabilize the EQs. At this stage, the EQ
pages are marked dirty to make sure the EQ pages are transferred if a
migration sequence is in progress.
The previous configuration of the sources is restored when the VM
resumes, after a migration or a stop. If an interrupt was queued while
the VM was stopped, the handler simply generates the missing trigger.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This extends the KVM XIVE device backend with 'synchronize_state'
methods used to retrieve the state from KVM. The HW state of the
sources, the KVM device and the thread interrupt contexts are
collected for the monitor usage and also migration.
These get operations rely on their KVM counterpart in the host kernel
which acts as a proxy for OPAL, the host firmware. The set operations
will be added for migration support later.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190513084245.25755-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
XIVE hcalls are all redirected to QEMU as none are on a fast path.
When necessary, QEMU invokes KVM through specific ioctls to perform
host operations. QEMU should have done the necessary checks before
calling KVM and, in case of failure, H_HARDWARE is simply returned.
H_INT_ESB is a special case that could have been handled under KVM
but the impact on performance was low when under QEMU. Here are some
figures :
kernel irqchip OFF ON
H_INT_ESB KVM QEMU
rtl8139 (LSI ) 1.19 1.24 1.23 Gbits/sec
virtio 31.80 42.30 -- Gbits/sec
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This introduces a set of helpers when KVM is in use, which create the
KVM XIVE device, initialize the interrupt sources at a KVM level and
connect the interrupt presenters to the vCPU.
They also handle the initialization of the TIMA and the source ESB
memory regions of the controller. These have a different type under
KVM. They are 'ram device' memory mappings, similarly to VFIO, exposed
to the guest and the associated VMAs on the host are populated
dynamically with the appropriate pages using a fault handler.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190513084245.25755-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
spapr machine capabilities are supposed to be sent in the migration stream
so that we can sanity check the source and destination have compatible
configuration. Unfortunately, when we added the hpt-max-page-size
capability, we forgot to add it to the migration state. This means that we
can generate spurious warnings when both ends are configured for large
pages, or potentially fail to warn if the source is configured for huge
pages, but the destination is not.
Fixes: 2309832afda "spapr: Maximum (HPT) pagesize property"
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
|
|
The high order bits of the address of the OS event queue is stored in
bits [4-31] of word2 of the XIVE END internal structures and the low
order bits in word3. This structure is using Big Endian ordering and
computing the value requires some simple arithmetic which happens to
be wrong. The mask removing bits [0-3] of word2 is applied to the
wrong value and the resulting address is bogus when above 64GB.
Guests with more than 64GB of RAM will allocate pages for the OS event
queues which will reside above the 64GB limit. In this case, the XIVE
device model will wake up the CPUs in case of a notification, such as
IPIs, but the update of the event queue will be written at the wrong
place in memory. The result is uncertain as the guest memory is
trashed and IPI are not delivered.
Introduce a helper xive_end_qaddr() to compute this value correctly in
all places where it is used.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190508171946.657-3-clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
'remotes/stsquad/tags/pull-testing-next-280519-2' into staging
Various testing updates
- semihosting re-factor (used in system tests)
- aarch64 and alpha system tests
- editorconfig tweak for .S
- some docker image updates
- iotests clean-up (without make check inclusion)
# gpg: Signature made Tue 28 May 2019 17:26:34 BST
# gpg: using RSA key 6685AE99E75167BCAFC8DF35FBD0DB095A9E2A44
# gpg: Good signature from "Alex Bennée (Master Work Key) <alex.bennee@linaro.org>" [full]
# Primary key fingerprint: 6685 AE99 E751 67BC AFC8 DF35 FBD0 DB09 5A9E 2A44
* remotes/stsquad/tags/pull-testing-next-280519-2: (27 commits)
tests/qemu-iotests: re-format output to for make check-block
tests/qemu-iotests/group: Re-use the "auto" group for tests that can always run
Makefile.target: support per-target coverage reports
Makefile: include per-target build directories in coverage report
Makefile: fix coverage-report reference to BUILD_DIR
.travis.yml: enable aarch64-softmmu and alpha-softmmu tcg tests
tests/tcg/alpha: add system boot.S
tests/tcg/multiarch: expand system memory test to cover more
tests/tcg/minilib: support %c format char
tests/tcg/multiarch: move the system memory test
tests/tcg/aarch64: add system boot.S
editorconfig: add settings for .s/.S files
tests/tcg/multiarch: add hello world system test
tests/tcg/multiarch: add support for multiarch system tests
tests/docker: Test more components on the Fedora default image
tests/docker: add ubuntu 18.04
MAINTAINERS: update for semihostings new home
target/mips: convert UHI_plog to use common semihosting code
target/mips: only build mips-semi for softmmu
target/arm: correct return values for WRITE/READ in arm-semi
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
into staging
RISC-V Patches for the 4.1 Soft Freeze, Part 1
This tag contains a handful of patches that I'd like to target for 4.1:
* An emulation for SiFive's GPIO device.
* A fix to disallow sfence.vma from userspace.
* Additional decodetree cleanups that should have no functional impact.
* C extension emulation fidelity fixes that were noticed as part of that
cleanup process.
* A new "spike" target, along with the deprecation of a handful of old
targets and CPUs.
* Some initial infastructure related to the hypervisor extension.
* An emulation fidelity fix that prevents prevents arbitrary bits in the
SIP CSR from being set.
* A small performance improvement that avoids excessive TLB flushing
when the ASID does not change.
This time I've used a new testing workflow: I've tested on both 32-bit
and 64-bit builds of OpenEmbedded, via the default OpenSBI-based boot
flow.
# gpg: Signature made Sat 25 May 2019 01:05:57 BST
# gpg: using RSA key 00CE76D1834960DFCE886DF8EF4CA1502CCBAB41
# gpg: issuer "palmer@dabbelt.com"
# gpg: Good signature from "Palmer Dabbelt <palmer@dabbelt.com>" [unknown]
# gpg: aka "Palmer Dabbelt <palmer@sifive.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 00CE 76D1 8349 60DF CE88 6DF8 EF4C A150 2CCB AB41
* remotes/palmer/tags/riscv-for-master-4.1-sf0: (29 commits)
target/riscv: Only flush TLB if SATP.ASID changes
target/riscv: More accurate handling of `sip` CSR
target/riscv: Add checks for several RVC reserved operands
target/riscv: Add the HGATP register masks
target/riscv: Add the HSTATUS register masks
target/riscv: Add Hypervisor CSR macros
target/riscv: Allow setting mstatus virtulisation bits
target/riscv: Add the MPV and MTL mstatus bits
target/riscv: Improve the scause logic
target/riscv: Trigger interrupt on MIP update asynchronously
target/riscv: Mark privilege level 2 as reserved
riscv: spike: Add a generic spike machine
target/riscv: Deprecate the generic no MMU CPUs
target/riscv: Add a base 32 and 64 bit CPU
target/riscv: Create settable CPU properties
riscv: virt: Allow specifying a CPU via commandline
linux-user/riscv: Add the CPU type as a comment
target/riscv: Remove unused include of riscv_htif.h for virt board riscv
target/riscv: Remove spaces from register names
target/riscv: Split gen_arith_imm into functional and temp
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
It will be useful for a number of use-cases to be able to re-direct
output to a file like we do with serial output. This does the wiring
to allow us to treat then semihosting console like just another
character output device.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
|
|
This provides two functions for handling console output that handle
the common backend behaviour for semihosting.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
|
|
In preparation for having some more common semihosting code let's
excise the current config magic from vl.c into its own file. We shall
later add more conditionals to the build configurations so we can
avoid building this if we don't need it.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
|
|
At the same time deprecate the ISA string CPUs.
It is dobtful anyone specifies the CPUs, but we are keeping them for the
Spike machine (which is about to be depreated) so we may as well just
mark them as deprecated.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
QEMU model of the GPIO device on the SiFive E300 series SOCs.
The pins are not used by a board definition yet, however this
implementation can already be used to trigger GPIO interrupts from the
software by configuring a pin as both output and input.
Signed-off-by: Fabien Chouteau <chouteau@adacore.com>
Reviewed-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
|
|
To be coherent with the other peripherals contained in the
BCM2835PeripheralState structure, directly allocate the PL011State
(instead of using the pl011 uart as a pointer to a SysBusDevice).
Initialize the PL011State with object_initialize() instead of
object_new().
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190507163416.24647-6-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20190507163416.24647-5-philmd@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
into staging
ramfb: misc improvements.
# gpg: Signature made Fri 24 May 2019 09:56:59 BST
# gpg: using RSA key 4CB6D8EED3E87138
# gpg: Good signature from "Gerd Hoffmann (work) <kraxel@redhat.com>" [full]
# gpg: aka "Gerd Hoffmann <gerd@kraxel.org>" [full]
# gpg: aka "Gerd Hoffmann (private) <kraxel@gmail.com>" [full]
# Primary key fingerprint: A032 8CFF B93A 17A7 9901 FE7D 4CB6 D8EE D3E8 7138
* remotes/kraxel/tags/vga-20190524-pull-request:
hw/display/ramfb: initialize fw-config space with xres/ yres
hw/display/ramfb: lock guest resolution after it's set
hw/display/ramfb: fix guest memory un-mapping
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
'remotes/pmaydell/tags/pull-target-arm-20190523' into staging
target-arm queue:
* exynos4210: QOM'ify the Exynos4210 SoC
* exynos4210: Add DMA support for the Exynos4210
* arm_gicv3: Fix writes to ICC_CTLR_EL3
* arm_gicv3: Fix write of ICH_VMCR_EL2.{VBPR0, VBPR1}
* target/arm: Fix vector operation segfault
* target/arm: Minor improvements to BFXIL, EXTR
# gpg: Signature made Thu 23 May 2019 15:22:55 BST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20190523:
hw/arm/exynos4210: QOM'ify the Exynos4210 SoC
hw/arm/exynos4210: Add DMA support for the Exynos4210
hw/arm/exynos4: Use the IEC binary prefix definitions
hw/arm/exynos4: Remove unuseful debug code
hw/intc/arm_gicv3: Fix writes to ICC_CTLR_EL3
hw/intc/arm_gicv3: Fix write of ICH_VMCR_EL2.{VBPR0, VBPR1}
arm: Rename hw/arm/arm.h to hw/arm/boot.h
arm: Remove unnecessary includes of hw/arm/arm.h
arm: Move system_clock_scale to armv7m_systick.h
target/arm: Fix vector operation segfault
target/arm: Simplify BFXIL expansion
target/arm: Use extract2 for EXTR
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
If xres / yres were specified in QEMU command line, write them as an initial
resolution to the fw-config space on guest reset, which a later BIOS / OVMF
patch can take advantage of.
Signed-off-by: HOU Qiming <hqm03ster@gmail.com>
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Message-id: 20190513115731.17588-4-marcel.apfelbaum@gmail.com
[fixed malformed patch]
Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20190520214342.13709-5-philmd@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The header file hw/arm/arm.h now includes only declarations
relating to hw/arm/boot.c functionality. Rename it accordingly,
and adjust its header comment.
The bulk of this commit was created via
perl -pi -e 's|hw/arm/arm.h|hw/arm/boot.h|' hw/arm/*.c include/hw/arm/*.h
In a few cases we can just delete the #include:
hw/arm/msf2-soc.c, include/hw/arm/aspeed_soc.h and
include/hw/arm/bcm2836.h did not require it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190516163857.6430-4-peter.maydell@linaro.org
|
|
The system_clock_scale global is used only by the armv7m systick
device; move the extern declaration to the armv7m_systick.h header,
and expand the comment to explain what it is and that it should
ideally be replaced with a different approach.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-id: 20190516163857.6430-2-peter.maydell@linaro.org
|
|
'remotes/philmd-gitlab/tags/fw_cfg-20190523-pull-request' into staging
fw_cfg patches for 2019-05-23
- Add trace events
- Get rid of globals in fw_cfg-test
- Explicit 'reboot-timeout' is little endian
- Add tests for 'reboot-timeout' and 'splash-time'
# gpg: Signature made Thu 23 May 2019 13:40:32 BST
# gpg: using RSA key E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* remotes/philmd-gitlab/tags/fw_cfg-20190523-pull-request:
tests: fw_cfg: add 'splash-time' test case
tests: fw_cfg: add 'reboot-timeout' test case
hw/nvram/fw_cfg: Store 'reboot-timeout' as little endian
tests: fw_cfg: add a function to get the fw_cfg file
tests: refactor fw_cfg_test
tests/fw_cfg: Free QFWCFG object after qtest has run
tests/libqos: Add pc_fw_cfg_uninit() and use it
tests/libqos: Add io_fw_cfg_uninit() and mm_fw_cfg_uninit()
hw/sparc64: Implement fw_cfg_arch_key_name()
hw/sparc: Implement fw_cfg_arch_key_name()
hw/ppc: Implement fw_cfg_arch_key_name()
hw/i386: Implement fw_cfg_arch_key_name()
hw/i386: Extract fw_cfg definitions to local "fw_cfg.h"
hw/nvram/fw_cfg: Add fw_cfg_arch_key_name()
hw/nvram/fw_cfg: Add trace events
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add fw_cfg_arch_key_name() which returns the name of
an architecture-specific key.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Message-Id: <20190422195020.1494-3-philmd@redhat.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
|
|
Introduce qemu_guest_getrandom.
Use qemu_guest_getrandom in aspeed, nrf51, bcm2835, exynos4210 rng devices.
Use qemu_guest_getrandom in target/ppc darn instruction.
Support ARMv8.5-RNG extension.
Support x86 RDRAND extension.
Acked-by: Daniel P. Berrangé <berrange@redhat.com>
Acked-by: Laurent Vivier <laurent@vivier.eu>
# gpg: Signature made Wed 22 May 2019 19:36:43 BST
# gpg: using RSA key 7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg: issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [full]
# Primary key fingerprint: 7A48 1E78 868B 4DB6 A85A 05C0 64DF 38E8 AF7E 215F
* remotes/rth/tags/pull-rng-20190522: (25 commits)
target/i386: Implement CPUID_EXT_RDRAND
target/ppc: Use qemu_guest_getrandom for DARN
target/ppc: Use gen_io_start/end around DARN
target/arm: Implement ARMv8.5-RNG
target/arm: Put all PAC keys into a structure
hw/misc/exynos4210_rng: Use qemu_guest_getrandom
hw/misc/bcm2835_rng: Use qemu_guest_getrandom_nofail
hw/misc/nrf51_rng: Use qemu_guest_getrandom_nofail
aspeed/scu: Use qemu_guest_getrandom_nofail
linux-user: Remove srand call
linux-user/aarch64: Use qemu_guest_getrandom for PAUTH keys
linux-user: Use qemu_guest_getrandom_nofail for AT_RANDOM
linux-user: Call qcrypto_init if not using -seed
linux-user: Initialize pseudo-random seeds for all guest cpus
cpus: Initialize pseudo-random seeds for all guest cpus
util: Add qemu_guest_getrandom and associated routines
ui/vnc: Use gcrypto_random_bytes for start_auth_vnc
ui/vnc: Split out authentication_failed
crypto: Change the qcrypto_random_bytes buffer type to void*
crypto: Use getrandom for qcrypto_random_bytes
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
When the -seed option is given, call qemu_guest_random_seed_main,
putting the subsystem into deterministic mode. Pass derived seeds
to each cpu created; which is a no-op unless the subsystem is in
deterministic mode.
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
This routine is intended to produce high-quality random numbers to the
guest. Normally, such numbers are crypto quality from the host, but a
command-line option can force the use of a fully deterministic sequence
for use while debugging.
Reviewed-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
