| Age | Commit message (Collapse) | Author |
|---|
|
ibm,architecture-vec-5 is supposed to encode all option vector 5 bits
negotiated between platform/guest. Currently we hardcode this property
in the boot-time device tree to advertise a single negotiated
capability, "Form 1" NUMA Affinity, regardless of whether or not CAS
has been invoked or that capability has actually been negotiated.
Improve this by generating ibm,architecture-vec-5 based on the full
set of option vector 5 capabilities negotiated via CAS.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
In some cases, ibm,client-architecture-support calls can fail. This
could happen in the current code for situations where the modified
device tree segment exceeds the buffer size provided by the guest
via the call parameters. In these cases, QEMU will reset, allowing
an opportunity to regenerate the device tree from scratch via
boot-time handling. There are potentially other scenarios as well,
not currently reachable in the current code, but possible in theory,
such as cases where device-tree properties or nodes need to be removed.
We currently don't handle either of these properly for option vector
capabilities however. Instead of carrying the negotiated capability
beyond the reset and creating the boot-time device tree accordingly,
we start from scratch, generating the same boot-time device tree as we
did prior to the CAS-generated and the same device tree updates as we
did before. This could (in theory) cause us to get stuck in a reset
loop. This hasn't been observed, but depending on the extensiveness
of CAS-induced device tree updates in the future, could eventually
become an issue.
Address this by pulling capability-related device tree
updates resulting from CAS calls into a common routine,
spapr_dt_cas_updates(), and adding an sPAPROptionVector*
parameter that allows us to test for newly-negotiated capabilities.
We invoke it as follows:
1) When ibm,client-architecture-support gets called, we
call spapr_dt_cas_updates() with the set of capabilities
added since the previous call to ibm,client-architecture-support.
For the initial boot, or a system reset generated by something
other than the CAS call itself, this set will consist of *all*
options supported both the platform and the guest. For calls
to ibm,client-architecture-support immediately after a CAS-induced
reset, we call spapr_dt_cas_updates() with only the set
of capabilities added since the previous call, since the other
capabilities will have already been addressed by the boot-time
device-tree this time around. In the unlikely event that
capabilities are *removed* since the previous CAS, we will
generate a CAS-induced reset. In the unlikely event that we
cannot fit the device-tree updates into the buffer provided
by the guest, well generate a CAS-induced reset.
2) When a CAS update results in the need to reset the machine and
include the updates in the boot-time device tree, we call the
spapr_dt_cas_updates() using the full set of negotiated
capabilities as part of the reset path. At initial boot, or after
a reset generated by something other than the CAS call itself,
this set will be empty, resulting in what should be the same
boot-time device-tree as we generated prior to this patch. For
CAS-induced reset, this routine will be called with the full set of
capabilities negotiated by the platform/guest in the previous
CAS call, which should result in CAS updates from previous call
being accounted for in the initial boot-time device tree.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Changed an int -> bool conversion to be more explicit]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Currently we access individual bytes of an option vector via
ldub_phys() to test for the presence of a particular capability
within that byte. Currently this is only done for the "dynamic
reconfiguration memory" capability bit. If that bit is present,
we pass a boolean value to spapr_h_cas_compose_response()
to generate a modified device tree segment with the additional
properties required to enable this functionality.
As more capability bits are added, will would need to modify the
code to add additional option vector accesses and extend the
param list for spapr_h_cas_compose_response() to include similar
boolean values for these parameters.
Avoid this by switching to spapr_ovec_* helpers so we can do all
the parsing in one shot and then test for these additional bits
within spapr_h_cas_compose_response() directly.
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
PAPR guests advertise their capabilities to the platform by passing
an ibm,architecture-vec structure via an
ibm,client-architecture-support hcall as described by LoPAPR v11,
B.6.2.3. during early boot.
Using this information, the platform enables the capabilities it
supports, then encodes a subset of those enabled capabilities (the
5th option vector of the ibm,architecture-vec structure passed to
ibm,client-architecture-support) into the guest device tree via
"/chosen/ibm,architecture-vec-5".
The logical format of these these option vectors is a bit-vector,
where individual bits are addressed/documented based on the byte-wise
offset from the beginning of the bit-vector, followed by the bit-wise
index starting from the byte-wise offset. Thus the bits of each of
these bytes are stored in reverse order. Additionally, the first
byte of each option vector is encodes the length of the option vector,
so byte offsets begin at 1, and bit offset at 0.
This is not very intuitive for the purposes of mapping these bits to
a particular documented capability, so this patch introduces a set
of abstractions that encapsulate the work of parsing/encoding these
options vectors and testing for individual capabilities.
Cc: Bharata B Rao <bharata@linux.vnet.ibm.com>
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
[dwg: Tweaked double-include protection to not trigger a checkpatch
false positive]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
For historical reasons construction of the guest device tree in spapr is
divided between spapr_create_fdt_skel() which is called at init time, and
spapr_build_fdt() which runs at reset time. Over time, more and more
things have needed to be moved to reset time.
Previous cleanups mean the only things left in spapr_create_fdt_skel() are
the properties of the root node itself. Finish consolidating these two
parts of device tree construction, by moving this to the start of
spapr_build_fdt(), and removing spapr_create_fdt_skel() entirely.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
|
|
Construction of the /vdevice node (and its children) is divided between
spapr_create_fdt_skel() (at init time), which creates the base node, and
spapr_populate_vdevice() (at reset time) which creates the nodes for each
individual virtual device.
This consolidates both into a single function called from
spapr_build_fdt().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
|
|
The /event-sources device tree node is built from spapr_create_fdt_skel().
As part of consolidating device tree construction to reset time, this moves
it to spapr_build_fdt().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
|
|
For historical reasons construction of the /rtas node in the device
tree (amongst others) is split into several places. In particular
it's split between spapr_create_fdt_skel(), spapr_build_fdt() and
spapr_rtas_device_tree_setup().
In fact, as well as adding the actual RTAS tokens to the device tree,
spapr_rtas_device_tree_setup() just adds the ibm,lrdr-capacity
property, which despite going in the /rtas node, doesn't have a lot to
do with RTAS.
This patch consolidates the code constructing /rtas together into a new
spapr_dt_rtas() function. spapr_rtas_device_tree_setup() is renamed to
spapr_dt_rtas_tokens() and now only adds the token properties.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
|
|
For historical reasons, building the /chosen node in the guest device tree
is split across several places and includes both parts which write the DT
sequentially and others which use random access functions.
This patch consolidates construction of the node into one place, using
random access functions throughout.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
|
|
Currently the device tree node for the XICS interrupt controller is in
spapr_create_fdt_skel(). As part of consolidating device tree construction
to reset time, this moves it to a function called from spapr_build_fdt().
In addition we move the actual code into hw/intc/xics_spapr.c with the
rest of the PAPR specific interrupt controller code.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
|
|
At each system reset, the pseries machine needs to load RTAS (the runtime
portion of the guest firmware) into the VM. This means copying
the actual RTAS code into guest memory, and also updating the device
tree so that the guest OS and boot firmware can locate it.
For historical reasons the copy and update to the device tree were in
different parts of the code. This cleanup brings them both together in
an spapr_load_rtas() function.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
|
|
Currently spapr_create_fdt_skel() takes a bunch of individual parameters
for various things it will put in the device tree. Some of these can
already be taken directly from sPAPRMachineState. This patch alters it so
that all of them can be taken from there, which will allow this code to
be moved away from its current caller in future.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
|
|
These values are used only within ppc_spapr_reset(), so just change them
to local variables.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
|
|
As Qemu only supports a single instance of the ISA bus, we use the LPC
controller of chip 0 to create one and plug in a couple of useful
devices, like an UART and RTC. An IPMI BT device, which is also an ISA
device, can be defined on the command line to connect an external BMC.
That is for later.
The PowerNV machine now has a console. Skiboot should load a kernel
and jump into it but execution will stop quite early because we lack a
model for the native XICS controller for the moment :
[ 0.000000] NR_IRQS:512 nr_irqs:512 16
[ 0.000000] XICS: Cannot find a Presentation Controller !
[ 0.000000] ------------[ cut here ]------------
[ 0.000000] WARNING: at arch/powerpc/platforms/powernv/setup.c:81
...
[ 0.000000] NIP [c00000000079d65c] pnv_init_IRQ+0x30/0x44
You can still do a few things under xmon.
Based on previous work from :
Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Trivial fix for a change in the serial_hds_isa_init() interface]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The LPC (Low Pin Count) interface on a POWER8 is made accessible to
the system through the ADU (XSCOM interface). This interface is part
of set of units connected together via a local OPB (On-Chip Peripheral
Bus) which act as a bridge between the ADU and the off chip LPC
endpoints, like external flash modules.
The most important units of this OPB are :
- OPB Master: contains the ADU slave logic, a set of internal
registers and the logic to control the OPB.
- LPCHC (LPC HOST Controller): which implements a OPB Slave, a set of
internal registers and the LPC HOST Controller to control the LPC
interface.
Four address spaces are provided to the ADU :
- LPC Bus Firmware Memory
- LPC Bus Memory
- LPC Bus I/O (ISA bus)
- and the registers for the OPB Master and the LPC Host Controller
On POWER8, an intermediate hop is necessary to reach the OPB, through
a unit called the ECCB. OPB commands are simply mangled in ECCB write
commands.
On POWER9, the OPB master address space can be accessed via MMIO. The
logic is same but the code will be simpler as the XSCOM and ECCB hops
are not necessary anymore.
This version of the LPC controller model doesn't yet implement support
for the SerIRQ deserializer present in the Naples version of the chip
though some preliminary work is there.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[clg: - updated for qemu-2.7
- ported on latest PowerNV patchset
- changed the XSCOM interface to fit new model
- QOMified the model
- moved the ISA hunks in another patch
- removed printf logging
- added a couple of UNIMP logging
- rewrote commit log ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Now that we are using real HW ids for the cores in PowerNV chips, we
can route the XSCOM accesses to them. We just need to attach a
specific XSCOM memory region to each core in the appropriate window
for the core number.
To start with, let's install the DTS (Digital Thermal Sensor) handlers
which should return 38°C for each core.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
On a real POWER8 system, the Pervasive Interconnect Bus (PIB) serves
as a backbone to connect different units of the system. The host
firmware connects to the PIB through a bridge unit, the
Alter-Display-Unit (ADU), which gives him access to all the chiplets
on the PCB network (Pervasive Connect Bus), the PIB acting as the root
of this network.
XSCOM (serial communication) is the interface to the sideband bus
provided by the POWER8 pervasive unit to read and write to chiplets
resources. This is needed by the host firmware, OPAL and to a lesser
extent, Linux. This is among others how the PCI Host bridges get
configured at boot or how the LPC bus is accessed.
To represent the ADU of a real system, we introduce a specific
AddressSpace to dispatch XSCOM accesses to the targeted chiplets. The
translation of an XSCOM address into a PCB register address is
slightly different between the P9 and the P8. This is handled before
the dispatch using a 8byte alignment for all.
To customize the device tree, a QOM InterfaceClass, PnvXScomInterface,
is provided with a populate() handler. The chip populates the device
tree by simply looping on its children. Therefore, each model needing
custom nodes should not forget to declare itself as a child at
instantiation time.
Based on previous work done by :
Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Added cpu parameter to xscom_complete()]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This is largy inspired by sPAPRCPUCore with some simplification, no
hotplug for instance. A set of PnvCore objects is added to the PnvChip
and the device tree is populated looping on these cores.
Real HW cpu ids are now generated depending on the chip cpu model, the
chip id and a core mask. The id is propagated to the CPU object, using
properties, to set the SPR_PIR (Processor Identification Register)
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The Processor Identification Register (PIR) is a register that holds a
processor identifier which is used for bus transactions (XSCOM) and
for processor differentiation in multiprocessor systems. It also used
in the interrupt vector entries (IVE) to identify the thread serving
the interrupts.
P9 and P8 have some differences in the CPU PIR encoding.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This will be used to build real HW ids for the cores and enforce some
limits on the available cores per chip.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This is is an abstraction of a POWER8 chip which is a set of cores
plus other 'units', like the pervasive unit, the interrupt controller,
the memory controller, the on-chip microcontroller, etc. The whole can
be seen as a socket. It depends on a cpu model and its characteristics:
max cores and specific inits are defined in a PnvChipClass.
We start with an near empty PnvChip with only a few cpu constants
which we will grow in the subsequent patches with the controllers
required to run the system.
The Chip CFAM (Common FRU Access Module) ID gives the model of the
chip and its version number. It is generally the first thing firmwares
fetch, available at XSCOM PCB address 0xf000f, to start initialization.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The goal is to emulate a PowerNV system at the level of the skiboot
firmware, which loads the OS and provides some runtime services. Power
Systems have a lower firmware (HostBoot) that does low level system
initialization, like DRAM training. This is beyond the scope of what
qemu will address in a PowerNV guest.
No devices yet, not even an interrupt controller. Just to get started,
some RAM to load the skiboot firmware, the kernel and initrd. The
device tree is fully created in the machine reset op.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[clg: - updated for qemu-2.7
- replaced fprintf by error_report
- used a common definition of _FDT macro
- removed VMStateDescription as migration is not yet supported
- added IBM Copyright statements
- reworked kernel_filename handling
- merged PnvSystem and sPowerNVMachineState
- removed PHANDLE_XICP
- added ppc_create_page_sizes_prop helper
- removed nmi support
- removed kvm support
- updated powernv machine to version 2.8
- removed chips and cpus, They will be provided in another patches
- added a machine reset routine to initialize the device tree (also)
- french has a squelette and english a skeleton.
- improved commit log.
- reworked prototypes parameters
- added a check on the ram size (thanks to Michael Ellerman)
- fixed chip-id cell
- changed MAX_CPUS to 2048
- simplified memory node creation to one node only
- removed machine version
- rewrote the device tree creation with the fdt "rw" routines
- s/sPowerNVMachineState/PnvMachineState/
- etc.]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The original QOMification of the spapr VIO devices in 3954d33 "spapr:
convert to QEMU Object Model (v2)" moved some callbacks from the
VIOsPAPRBus structure to the VIOsPAPRDeviceClass. Except, that it
forgot to actually remove them from the VIOsPAPRBus structure (which
still exists, though it doesn't fulfill quite the same function as it
did pre-QOM).
This patch removes those now unused callback fields.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Thomas Huth <thuth@redhat.com>
|
|
The routines :
void icp_set_cppr(ICPState *icp, uint8_t cppr);
void icp_set_mfrr(ICPState *icp, uint8_t mfrr);
void icp_eoi(ICPState *icp, uint32_t xirr);
now use one 'ICPState *icp' argument instead of a 'XICSState *' and a
server arguments. The backlink on XICSState* is used whenever needed.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The link will be used to change the API of the icp_* routines which
are still using an XICSState as an argument.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
xics_spapr and xics_kvm nearly define the same 'set_nr_servers'
handler. Only the type of the ICP differs. So let's make a common one
to remove some duplicated code.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The header now only contains inline functions related to the
Sun NVRAM, so the a name like sun_nvram.h seems to be more
appropriate now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Everything that is related to CHRP NVRAM should rather reside in
chrp_nvram.c / chrp_nvram.h instead of openbios_firmware_abi.h.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The "system partition" and "free space" partition layouts are
defined by the CHRP and LoPAPR specification, and used by
OpenBIOS and SLOF. We can re-use this code for other machines
that use OpenBIOS and SLOF, too. So let's make this code independent
from the MAC NVRAM environment and put it into two proper helper
functions.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Force the use of cmpxchg16b on x86_64.
Wikipedia suggests that only very old AMD64 (circa 2004) did not have
this instruction. Further, it's required by Windows 8 so no new cpus
will ever omit it.
If we truely care about these, then we could check this at startup time
and then avoid executing paths that use it.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
|
|
When we cannot emulate an atomic operation within a parallel
context, this exception allows us to stop the world and try
again in a serial context.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
|
|
Allows Int128 to be used more generally, rather than having to
begin with 64-bit inputs and accumulate.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
|
|
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
|
|
Reviewed-by: Emilio G. Cota <cota@braap.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
|
|
While the check against sizeof(void *) is appropriate for
normal usage within qemu, there are places in which we want
wider operaions and have checked for their existance.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
|
|
This paves the way for upcoming work.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Message-Id: <1467054136-10430-9-git-send-email-cota@braap.org>
|
|
This paves the way for upcoming work.
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
Message-Id: <1467054136-10430-8-git-send-email-cota@braap.org>
|
|
Making these functional rather than object macros will
prevent later problems with complex macro expansion.
Reviewed-by: Emilio G. Cota <cota@braap.org>
Signed-off-by: Richard Henderson <rth@twiddle.net>
|
|
The qdict_flatten() method will take a dict whose elements are
further nested dicts/lists and flatten them by concatenating
keys.
The qdict_crumple() method aims to do the reverse, taking a flat
qdict, and turning it into a set of nested dicts/lists. It will
apply nesting based on the key name, with a '.' indicating a
new level in the hierarchy. If the keys in the nested structure
are all numeric, it will create a list, otherwise it will create
a dict.
If the keys are a mixture of numeric and non-numeric, or the
numeric keys are not in strictly ascending order, an error will
be reported.
As an example, a flat dict containing
{
'foo.0.bar': 'one',
'foo.0.wizz': '1',
'foo.1.bar': 'two',
'foo.1.wizz': '2'
}
will get turned into a dict with one element 'foo' whose
value is a list. The list elements will each in turn be
dicts.
{
'foo': [
{ 'bar': 'one', 'wizz': '1' },
{ 'bar': 'two', 'wizz': '2' }
],
}
If the key is intended to contain a literal '.', then it must
be escaped as '..'. ie a flat dict
{
'foo..bar': 'wizz',
'bar.foo..bar': 'eek',
'bar.hello': 'world'
}
Will end up as
{
'foo.bar': 'wizz',
'bar': {
'foo.bar': 'eek',
'hello': 'world'
}
}
The intent of this function is that it allows a set of QemuOpts
to be turned into a nested data structure that mirrors the nesting
used when the same object is defined over QMP.
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1475246744-29302-3-git-send-email-berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Parameter recursive dropped along with its tests; whitespace style
touched up]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
|
|
The QmpOutputVisitor has no direct dependency on QMP. It is
valid to use it anywhere that one wants a QObject. Rename it
to better reflect its functionality as a generic QAPI
to QObject converter.
The commit before previous renamed the files, this one renames C
identifiers.
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1475246744-29302-6-git-send-email-berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Split into file rename and identifier rename]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
|
|
The QmpInputVisitor has no direct dependency on QMP. It is
valid to use it anywhere that one has a QObject. Rename it
to better reflect its functionality as a generic QObject
to QAPI converter.
The previous commit renamed the files, this one renames C identifiers.
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1475246744-29302-5-git-send-email-berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Straightforwardly rebased, split into file and identifier rename]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
|
|
The QMP visitors have no direct dependency on QMP. It is
valid to use them anywhere that one has a QObject. Rename them
to better reflect their functionality as a generic QObject
to QAPI converter.
This is the first of three parts: rename the files. The next two
parts will rename C identifiers. The split is necessary to make git
rename detection work.
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
[Split into file and identifier rename, two comments touched up]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
|
|
staging
x86 and CPU queue, 2016-10-24
x2APIC support to APIC code, cpu_exec_init() refactor on all
architectures, and other x86 changes.
# gpg: Signature made Mon 24 Oct 2016 20:51:14 BST
# gpg: using RSA key 0x2807936F984DC5A6
# gpg: Good signature from "Eduardo Habkost <ehabkost@redhat.com>"
# Primary key fingerprint: 5A32 2FD5 ABC4 D3DB ACCF D1AA 2807 936F 984D C5A6
* remotes/ehabkost/tags/x86-pull-request:
exec: call cpu_exec_exit() from a CPU unrealize common function
exec: move cpu_exec_init() calls to realize functions
exec: split cpu_exec_init()
pc: q35: Bump max_cpus to 288
pc: Require IRQ remapping and EIM if there could be x2APIC CPUs
pc: Add 'etc/boot-cpus' fw_cfg file for machine with more than 255 CPUs
Increase MAX_CPUMASK_BITS from 255 to 288
pc: Clarify FW_CFG_MAX_CPUS usage comment
pc: kvm_apic: Pass APIC ID depending on xAPIC/x2APIC mode
pc: apic_common: Reset APIC ID to initial ID when switching into x2APIC mode
pc: apic_common: Restore APIC ID to initial ID on reset
pc: apic_common: Extend APIC ID property to 32bit
pc: Leave max apic_id_limit only in legacy cpu hotplug code
acpi: cphp: Force switch to modern cpu hotplug if APIC ID > 254
pc: acpi: x2APIC support for SRAT table
pc: acpi: x2APIC support for MADT table and _MAT method
Conflicts:
target-arm/cpu.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
As cpu_exec_exit() mirrors the cpu_exec_realizefn(),
rename it as cpu_exec_unrealizefn().
Create and register a cpu_common_unrealizefn() function for
the CPU device class and call cpu_exec_unrealizefn() from
this function.
Remove cpu_exec_exit() from cpu_common_finalize()
(which mirrors init, not realize), and as x86_cpu_unrealizefn()
and ppc_cpu_unrealizefn() overwrite the device class unrealize function,
add a call to a parent_unrealize pointer.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
Modify all CPUs to call it from XXX_cpu_realizefn() function.
Remove all the cannot_destroy_with_object_finalize_yet as
unsafe references have been moved to cpu_exec_realizefn().
(tested with QOM command provided by commit 4c315c27)
for arm:
Setting of cpu->mp_affinity is moved from arm_cpu_initfn()
to arm_cpu_realizefn() as setting of cpu_index is now done
in cpu_exec_realizefn(). To avoid to overwrite an user defined
value, we set it to an invalid value by default, and update
it in realize function only if the value is still invalid.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
Put in cpu_exec_initfn() what initializes the CPU,
and leave in cpu_exec_init() what adds it to the environment.
As cpu_exec_initfn() is called by all XX_cpu_initfn(), call it
directly in cpu_common_initfn().
cpu_exec_init() is now a realize function, it will be renamed
to cpu_exec_realizefn() and moved to the XX_cpu_realizefn()
function in a following patch.
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
Currently firmware uses 1 byte at 0x5F offset in RTC CMOS
to get number of CPUs present at boot. However 1 byte is
not enough to handle more than 255 CPUs. So add a new
fw_cfg file that would allow QEMU to tell it.
For compat reasons add file only for machine types that
support more than 255 CPUs.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
so that it would be possible to increase maxcpus limit
for x86 target. Keep spapr/virt_arm at limit they used
to have 255.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
ACPI ID is 32 bit wide on CPUs with x2APIC support.
Extend 'id' property to support it.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
