| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210430113547.1816178-1-kraxel@redhat.com
Message-Id: <20210430113547.1816178-5-kraxel@redhat.com>
|
|
Move device init (realize) and properties.
Drop the virgl property, the virtio-gpu-gl-device has virgl enabled no
matter what. Just use virtio-gpu-device instead if you don't want
enable virgl and opengl. This simplifies the logic and reduces the test
matrix.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210430113547.1816178-1-kraxel@redhat.com
Message-Id: <20210430113547.1816178-4-kraxel@redhat.com>
|
|
Just a skeleton for starters, following patches will add more code.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210430113547.1816178-1-kraxel@redhat.com
Message-Id: <20210430113547.1816178-3-kraxel@redhat.com>
|
|
dma_memory_map() may map only a part of the request. Happens if the
request can't be mapped in one go, for example due to a iommu creating
a linear dma mapping for scattered physical pages. Should that be the
case virtio-gpu must call dma_memory_map() again with the remaining
range instead of simply throwing an error.
Note that this change implies the number of iov entries may differ from
the number of mapping entries sent by the guest. Therefore the iov_len
bookkeeping needs some updates too, we have to explicitly pass around
the iov length now.
Reported-by: Auger Eric <eric.auger@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210506091001.1301250-1-kraxel@redhat.com
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Tested-by: Eric Auger <eric.auger@redhat.com>
Message-Id: <20210506091001.1301250-1-kraxel@redhat.com>
|
|
Signed-off-by: Akihiko Odaki <akihiko.odaki@gmail.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20210427150824.638359-1-kraxel@redhat.com
Message-Id: <20210427150824.638359-6-kraxel@redhat.com>
|
|
into staging
ppc patch queue 2021-05-04
Here's the first ppc pull request for qemu-6.1. It has a wide variety
of stuff accumulated during the 6.0 freeze. Highlights are:
* Multi-phase reset cleanups for PAPR
* Preliminary cleanups towards allowing !CONFIG_TCG for the ppc target
* Cleanup of AIL logic and extension to POWER10
* Further improvements to handling of hot unplug failures on PAPR
* Allow much larger numbers of CPU on pseries
* Support for the H_SCM_HEALTH hypercall
* Add support for the Pegasos II board
* Substantial cleanup to hflag handling
* Assorted minor fixes and cleanups
# gpg: Signature made Tue 04 May 2021 06:52:39 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-6.1-20210504: (46 commits)
hw/ppc/pnv_psi: Use device_cold_reset() instead of device_legacy_reset()
hw/ppc/spapr_vio: Reset TCE table object with device_cold_reset()
hw/intc/spapr_xive: Use device_cold_reset() instead of device_legacy_reset()
target/ppc: removed VSCR from SPR registration
target/ppc: Reduce the size of ppc_spr_t
target/ppc: Clean up _spr_register et al
target/ppc: Add POWER10 exception model
target/ppc: rework AIL logic in interrupt delivery
target/ppc: move opcode table logic to translate.c
target/ppc: code motion from translate_init.c.inc to gdbstub.c
spapr_drc.c: handle hotunplug errors in drc_unisolate_logical()
spapr.h: increase FDT_MAX_SIZE
spapr.c: do not use MachineClass::max_cpus to limit CPUs
ppc: Rename current DAWR macros and variables
target/ppc: POWER10 supports scv
target/ppc: Fix POWER9 radix guest HV interrupt AIL behaviour
docs/system: ppc: Add documentation for ppce500 machine
roms/u-boot: Bump ppce500 u-boot to v2021.04 to fix broken pci support
roms/Makefile: Update ppce500 u-boot build directory name
ppc/spapr: Add support for implement support for H_SCM_HEALTH
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
'remotes/vivier2/tags/trivial-branch-for-6.1-pull-request' into staging
Trivial patches pull request 20210503
# gpg: Signature made Mon 03 May 2021 09:34:56 BST
# gpg: using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg: issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier2/tags/trivial-branch-for-6.1-pull-request: (23 commits)
hw/rx/rx-gdbsim: Do not accept invalid memory size
docs: More precisely describe memory-backend-*::id's user
scripts: fix generation update-binfmts templates
docs/system: Document the removal of "compat" property for POWER CPUs
mc146818rtc: put it into the 'misc' category
Do not include exec/address-spaces.h if it's not really necessary
Do not include cpu.h if it's not really necessary
Do not include hw/boards.h if it's not really necessary
Do not include sysemu/sysemu.h if it's not really necessary
hw: Do not include qemu/log.h if it is not necessary
hw: Do not include hw/irq.h if it is not necessary
hw: Do not include hw/sysbus.h if it is not necessary
hw: Remove superfluous includes of hw/hw.h
ui: Fix memory leak in qemu_xkeymap_mapping_table()
hw/usb: Constify VMStateDescription
hw/display/qxl: Constify VMStateDescription
hw/arm: Constify VMStateDescription
vmstate: Constify some VMStateDescriptions
Fix typo in CFI build documentation
hw/pcmcia: Do not register PCMCIA type if not required
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
into staging
Aspeed patches :
* Fixes for the DMA space
* New model for ASPEED's Hash and Crypto Engine (Joel and Klaus)
* Acceptance tests (Joel)
* A fix for the XDMA model
* Some extra features for the SMC controller.
* Two new boards : rainier-bmc and quanta-q7l1-bmc (Patrick)
# gpg: Signature made Mon 03 May 2021 06:23:36 BST
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* remotes/legoater/tags/pull-aspeed-20210503:
aspeed: Add support for the quanta-q7l1-bmc board
hw/block: m25p80: Add support for mt25ql02g and mt25qu02g
aspeed: Add support for the rainier-bmc board
aspeed: Deprecate the swift-bmc machine
tests/qtest: Rename m25p80 test in aspeed_smc test
aspeed/smc: Add extra controls to request DMA
aspeed/smc: Add a 'features' attribute to the object class
hw/misc/aspeed_xdma: Add AST2600 support
tests/acceptance: Test ast2600 machine
tests/acceptance: Test ast2400 and ast2500 machines
tests/qtest: Add test for Aspeed HACE
aspeed: Integrate HACE
hw: Model ASPEED's Hash and Crypto Engine
hw/arm/aspeed: Do not sysbus-map mmio flash region directly, use alias
aspeed/i2c: Rename DMA address space
aspeed/i2c: Fix DMA address mask
aspeed/smc: Remove unused "sdram-base" property
aspeed/smc: Use the RAM memory region for DMAs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Certain SMP topologies stress, e.g. 1 thread/core, 2048 cores and
1 socket, stress the current maximum size of the pSeries FDT:
Calling ibm,client-architecture-support...qemu-system-ppc64: error
creating device tree: (fdt_setprop(fdt, offset,
"ibm,processor-segment-sizes", segs, sizeof(segs))): FDT_ERR_NOSPACE
2048 is the default NR_CPUS value for the pSeries kernel. It's expected
that users will want QEMU to be able to handle this kind of
configuration.
Bumping FDT_MAX_SIZE to 2MB is enough for these setups to be created.
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210408204049.221802-3-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Power10 is introducing second DAWR. Use real register names (with
suffix 0) from ISA for current macros and variables used by Qemu.
One exception to this is KVM_REG_PPC_DAWR[X]. This is from kernel
uapi header and thus not changed in kernel as well as Qemu.
Signed-off-by: Ravi Bangoria <ravi.bangoria@linux.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20210412114433.129702-3-ravi.bangoria@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Add support for H_SCM_HEALTH hcall described at [1] for spapr
nvdimms. This enables guest to detect the 'unarmed' status of a
specific spapr nvdimm identified by its DRC and if its unarmed, mark
the region backed by the nvdimm as read-only.
The patch adds h_scm_health() to handle the H_SCM_HEALTH hcall which
returns two 64-bit bitmaps (health bitmap, health bitmap mask) derived
from 'struct nvdimm->unarmed' member.
Linux kernel side changes to enable handling of 'unarmed' nvdimms for
ppc64 are proposed at [2].
References:
[1] "Hypercall Op-codes (hcalls)"
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/powerpc/papr_hcalls.rst#n220
[2] "powerpc/papr_scm: Mark nvdimm as unarmed if needed during probe"
https://lore.kernel.org/linux-nvdimm/20210329113103.476760-1-vaibhav@linux.ibm.com/
Signed-off-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Message-Id: <20210402102128.213943-1-vaibhav@linux.ibm.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The Marvell Discovery II aka. MV64361 is a PowerPC system controller
chip that is used on the pegasos2 PPC board. This adds emulation of it
that models the device enough to boot guests on this board. The
mv643xx.h header with register definitions is taken from Linux 4.15.10
only fixing white space errors, removing not needed parts and changing
formatting for QEMU coding style.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <79545ebd03bfe0665b73d2d7cbc74fdf3d62629e.1616680239.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Add emulation of VT8231 south bridge ISA part based on the similar
VT82C686B but implemented in a separate subclass that holds the
differences while reusing parts that can be shared.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <10abc9f89854e7c980b9731c33d25a2e307e9c4f.1616680239.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
To allow reusing ISA bridge emulation for vt8231_isa move the device
state of vt82c686b_isa emulation in an abstract via_isa class. This
change breaks migration back compatibility but this is not an issue
for Fuloong2E machine which is not versioned or migration supported.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <0cb8fc69c7aaa555589181931b881335fecd2ef3.1616680239.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Collect superio functionality and its controlling config registers
handling in an abstract VIA_SUPERIO class that is a subclass of
ISA_SUPERIO and put vt82c686b specific parts in a subclass of this
abstract class.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Message-Id: <fbcc8cc8baf83f327612a1ef1c14bcbcdb0e7edb.1616680239.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The include/hw/hw.h header only has a prototype for hw_error(),
so it does not make sense to include this in files that do not
use this function.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210326151848.2217216-1-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
|
|
Constify vmstate_ecc_state and vmstate_x86_cpu.
Signed-off-by: Keqian Zhu <zhukeqian1@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20210408140706.23412-1-zhukeqian1@huawei.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
|
|
The AST2600 SPI controllers have a set of bits to request/grant DMA
access. Add a new SMC feature for these controllers and use it to
check access to the DMA registers.
Cc: Chin-Ting Kuo <chin-ting_kuo@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210407171637.777743-16-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
|
|
It will simplify extensions of the SMC model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210407171637.777743-15-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
|
|
When we introduced support for the AST2600 SoC, the XDMA controller
was forgotten. It went unnoticed because it's not used under emulation.
But the register layout being different, the reset procedure is bogus
and this breaks kexec.
Add a AspeedXDMAClass to take into account the register differences.
Cc: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Message-Id: <20210407171637.777743-14-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
|
|
Add the hash and crypto engine model to the Aspeed socs.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Klaus Heinrich Kiwi <klaus@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Message-Id: <20210409000253.1475587-3-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
|
|
The HACE (Hash and Crypto Engine) is a device that offloads MD5, SHA1,
SHA2, RSA and other cryptographic algorithms.
This initial model implements a subset of the device's functionality;
currently only MD5/SHA hashing, and on the ast2600's scatter gather
engine.
Co-developed-by: Klaus Heinrich Kiwi <klaus@linux.vnet.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
[ clg: - fixes for 32-bit and OSX builds ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210409000253.1475587-2-joel@jms.id.au>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
|
|
The flash mmio region is exposed as an AddressSpace.
AddressSpaces must not be sysbus-mapped, therefore map
the region using an alias.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
[ clg : Fix DMA_FLASH_ADDR() ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210312182851.1922972-3-f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20210407171637.777743-6-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
|
|
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210407171637.777743-3-clg@kaod.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
|
|
Currently the gpex PCI controller implements no special behaviour for
guest accesses to areas of the PIO and MMIO where it has not mapped
any PCI devices, which means that for Arm you end up with a CPU
exception due to a data abort.
Most host OSes expect "like an x86 PC" behaviour, where bad accesses
like this return -1 for reads and ignore writes. In the interests of
not being surprising, make host CPU accesses to these windows behave
as -1/discard where there's no mapped PCI device.
The old behaviour generally didn't cause any problems, because
almost always the guest OS will map the PCI devices and then only
access where it has mapped them. One corner case where you will see
this kind of access is if Linux attempts to probe legacy ISA
devices via a PIO window access. So far the only case where we've
seen this has been via the syzkaller fuzzer.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 20210325163315.27724-1-peter.maydell@linaro.org
Fixes: https://bugs.launchpad.net/qemu/+bug/1918917
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add 6.1 machine types for arm/i440fx/q35/s390x/spapr.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Acked-by: Greg Kurz <groug@kaod.org>
Message-id: 20210331111900.118274-1-cohuck@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The pca954x is an i2c mux, and this adds support for two variants of
this device: the pca9546 and pca9548.
This device is very common on BMCs to route a different channel to each
PCIe i2c bus downstream from the BMC.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com>
Message-Id: <20210412194522.664594-5-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
Moves the search for matching devices on an i2c bus into a separate
method. This allows for an object that owns an I2CBus can avoid
duplicating this method.
Tested: A BMC firmware was booted to userspace and i2c devices were
detected.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-Id: <20210412194522.664594-4-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
At the start of an i2c transaction, the i2c bus searches its list of
children to identify which devices correspond to the address (or
broadcast). Now the I2CSlave device has a method "match" that
encapsulates the lookup behavior. This allows the behavior to be changed
to support devices, such as i2c muxes.
Tested: A BMC firmware was booted to userspace and i2c devices were
detected.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Message-Id: <20210412194522.664594-3-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
To enable passing the current_devs field as a parameter, we need to use
a named struct type.
Tested: BMC firmware with i2c devices booted to userspace.
Signed-off-by: Patrick Venture <venture@google.com>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20210412194522.664594-2-venture@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
into staging
ppc patch queue for 2021-04-21
Here's what I hope is the last ppc related pull request for qemu-6.0.
The 2 patches here revert a behavioural change that after further
discussion we concluded was a bad idea (adding a timeout for
possibly-failed hot unplug requests). Instead it implements a
different approach to the original problem: we again let unplug
requests the guest doesn't respond to remain pending indefinitely, but
no longer allow those to block attempts to retry the same unplug
again.
The change is a bit more complex than I'd like for this late in the
freeze. Nonetheless, I think it's important to merge this for 6.0, so
we don't allow a release which has the probably-a-bad-idea timeout
behaviour.
# gpg: Signature made Mon 12 Apr 2021 06:25:58 BST
# gpg: using RSA key 75F46586AE61A66CC44E87DC6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>" [full]
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>" [full]
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>" [full]
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>" [unknown]
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dg-gitlab/tags/ppc-for-6.0-20210412:
spapr.c: always pulse guest IRQ in spapr_core_unplug_request()
spapr: rollback 'unplug timeout' for CPU hotunplugs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
If QEMU is launched with the -S option then the ESPState mig_version_id property
is left unset due to the ordering of the VMState fields in the VMStateDescription
for sysbusespscsi and pciespscsi. If the VM is migrated and restored in this
stopped state, the version tests in the vmstate_esp VMStateDescription and
esp_post_load() become confused causing the migration to fail.
Fix the ordering problem by moving the setting of mig_version_id to a common
esp_pre_save() function which is invoked first by both sysbusespscsi and
pciespscsi rather than at the point where ESPState is itself serialised into the
migration stream.
Buglink: https://bugs.launchpad.net/qemu/+bug/1922611
Fixes: 0bd005be78 ("esp: add vmstate_esp version to embedded ESPState")
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210407124842.32695-1-mark.cave-ayland@ilande.co.uk>
|
|
The pseries machines introduced the concept of 'unplug timeout' for CPU
hotunplugs. The idea was to circunvent a deficiency in the pSeries
specification (PAPR), that currently does not define a proper way for
the hotunplug to fail. If the guest refuses to release the CPU (see [1]
for an example) there is no way for QEMU to detect the failure.
Further discussions about how to send a QAPI event to inform about the
hotunplug timeout [2] exposed problems that weren't predicted back when
the idea was developed. Other QEMU machines don't have any type of
hotunplug timeout mechanism for any device, e.g. ACPI based machines
have a way to make hotunplug errors visible to the hypervisor. This
would make this timeout mechanism exclusive to pSeries, which is not
ideal.
The real problem is that a QAPI event that reports hotunplug timeouts
puts the management layer (namely Libvirt) in a weird spot. We're not
telling that the hotunplug failed, because we can't be 100% sure of
that, and yet we're resetting the unplug state back, preventing any
DEVICE_DEL events to reach out in case the guest decides to release the
device. Libvirt would need to inspect the guest itself to see if the
device was released or not, otherwise the internal domain states will be
inconsistent. Moreover, Libvirt already has an 'unplug timeout'
concept, and a QEMU side timeout would need to be juggled together with
the existing Libvirt timeout.
All this considered, this solution ended up creating more trouble than
it solved. This patch reverts the 3 commits that introduced the timeout
mechanism for CPU hotplugs in pSeries machines.
This reverts commit 4515a5f786024fabf0bef4cf3d28adf5647e6e82
"qemu_timer.c: add timer_deadline_ms() helper"
This reverts commit d1c2e3ce3d5a5424651967bce1cf1f4caa0c6d91
"spapr_drc.c: add hotunplug timeout for CPUs"
This reverts commit 51254ffb320183a4636635840c23ee0e3a1efffa
"spapr_drc.c: introduce unplug_timeout_timer"
[1] https://bugzilla.redhat.com/show_bug.cgi?id=1911414
[2] https://lists.gnu.org/archive/html/qemu-devel/2021-03/msg04682.html
CC: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Message-Id: <20210401000437.131140-2-danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
'remotes/pmaydell/tags/pull-target-arm-20210406' into staging
target-arm queue:
* ppc/e500 and arm/virt: only add valid dynamic sysbus devices to the
platform bus
* update i.mx31 maintainer list
* Revert "target/arm: Make number of counters in PMCR follow the CPU"
# gpg: Signature made Tue 06 Apr 2021 13:25:54 BST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20210406:
Remove myself as i.mx31 maintainer
Revert "target/arm: Make number of counters in PMCR follow the CPU"
hw/ppc/e500plat: Only try to add valid dynamic sysbus devices to platform bus
hw/arm/virt: Only try to add valid dynamic sysbus devices to platform bus
machine: Provide a function to check the dynamic sysbus allowlist
include/hw/boards.h: Document machine_class_allow_dynamic_sysbus_dev()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Commit 4c70875372b8 ("pci: advertise a page aligned ATS") advertises
the page aligned via ATS capability (RO) to unbrek recent Linux IOMMU
drivers since 5.2. But it forgot the compat the capability which
breaks the migration from old machine type:
(qemu) qemu-kvm: get_pci_config_device: Bad config data: i=0x104 read:
0 device: 20 cmask: ff wmask: 0 w1cmask:0
This patch introduces a new parameter "x-ats-page-aligned" for
virtio-pci device and turns it on for machine type which is newer than
5.1.
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: qemu-stable@nongnu.org
Fixes: 4c70875372b8 ("pci: advertise a page aligned ATS")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20210406040330.11306-1-jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Provide a new function dynamic_sysbus_dev_allowed() which checks the
per-machine list of permitted dynamic sysbus devices and returns a
boolean result indicating whether the device is allowed. We can use
this in the implementation of validate_sysbus_device(), but we will
also need it so that machine hotplug callbacks can validate devices
rather than assuming that any sysbus device might be hotpluggable
into the platform bus.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210325153310.9131-3-peter.maydell@linaro.org
|
|
The function machine_class_allow_dynamic_sysbus_dev() is currently
undocumented; add a doc comment.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20210325153310.9131-2-peter.maydell@linaro.org
|
|
After introducing non-scalar machine properties, it would be preferrable
to have a single acpitable property which includes both generic
information (such as the OEM ids) and custom tables currently
passed via -acpitable.
Do not saddle ourselves with legacy oem-id and oem-table-id
properties, instead mark them as experimental.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20210402082128.13854-1-pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
There is no H_REGISTER_PROCESS_TABLE, it is H_REGISTER_PROC_TBL handler
for which is still called h_register_process_table() though.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20210225032335.64245-1-aik@ozlabs.ru>
Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The definition S390_ADAPTER_SUPPRESSIBLE was moved to "cpu.h", per
suggestion of Thomas Huth. From interface design perspective, IMHO, not
a good thing as it belongs to the public interface of
css_register_io_adapters(). We did this because CONFIG_KVM requeires
NEED_CPU_H and Thomas, and other commenters did not like the
consequences of that.
Moving the interrupt related declarations to s390_flic.h was suggested
by Cornelia Huck.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Halil Pasic <pasic@linux.ibm.com>
Message-Id: <20210317095622.2839895-2-kraxel@redhat.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
'remotes/pmaydell/tags/pull-target-arm-20210323' into staging
target-arm queue:
* hw/arm/virt: Disable pl011 clock migration if needed
* target/arm: Make M-profile VTOR loads on reset handle memory aliasing
* target/arm: Set ARMMMUFaultInfo.level in user-only arm_cpu_tlb_fill
# gpg: Signature made Tue 23 Mar 2021 14:26:09 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20210323:
target/arm: Set ARMMMUFaultInfo.level in user-only arm_cpu_tlb_fill
target/arm: Make M-profile VTOR loads on reset handle memory aliasing
hw/core/loader: Add new function rom_ptr_for_as()
memory: Add offset_in_region to flatview_cb arguments
memory: Document flatview_for_each_range()
memory: Make flatview_cb return bool, not int
hw/arm/virt: Disable pl011 clock migration if needed
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
'remotes/alistair/tags/pull-riscv-to-apply-20210322-2' into staging
RISC-V PR for 6.0
This PR includes:
- Fix for vector CSR access
- Improvements to the Ibex UART device
- PMP improvements and bug fixes
- Hypervisor extension bug fixes
- ramfb support for the virt machine
- Fast read support for SST flash
- Improvements to the microchip_pfsoc machine
# gpg: Signature made Tue 23 Mar 2021 01:56:53 GMT
# gpg: using RSA key F6C4AC46D4934868D3B8CE8F21E10D29DF977054
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [full]
# Primary key fingerprint: F6C4 AC46 D493 4868 D3B8 CE8F 21E1 0D29 DF97 7054
* remotes/alistair/tags/pull-riscv-to-apply-20210322-2:
target/riscv: Prevent lost illegal instruction exceptions
docs/system: riscv: Add documentation for 'microchip-icicle-kit' machine
hw/riscv: microchip_pfsoc: Map EMMC/SD mux register
hw/block: m25p80: Support fast read for SST flashes
target/riscv: Add proper two-stage lookup exception detection
target/riscv: Fix read and write accesses to vsip and vsie
hw/riscv: allow ramfb on virt
hw/riscv: Add fw_cfg support to virt
target/riscv: Use background registers also for MSTATUS_MPV
target/riscv: Make VSTIP and VSEIP read-only in hip
target/riscv: Adjust privilege level for HLV(X)/HSV instructions
target/riscv: flush TLB pages if PMP permission has been changed
target/riscv: add log of PMP permission checking
target/riscv: propagate PMP permission to TLB page
hw/char: disable ibex uart receive if the buffer is full
target/riscv: fix vs() to return proper error code
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
For accesses to rom blob data before or during reset, we have a
function rom_ptr() which looks for a rom blob that would be loaded to
the specified address, and returns a pointer into the rom blob data
corresponding to that address. This allows board or CPU code to say
"what is the data that is going to be loaded to this address?".
However, this function does not take account of memory region
aliases. If for instance a machine model has RAM at address
0x0000_0000 which is aliased to also appear at 0x1000_0000, a
rom_ptr() query for address 0x0000_0000 will only return a match if
the guest image provided by the user was loaded at 0x0000_0000 and
not if it was loaded at 0x1000_0000, even though they are the same
RAM and a run-time guest CPU read of 0x0000_0000 will read the data
loaded to 0x1000_0000.
Provide a new function rom_ptr_for_as() which takes an AddressSpace
argument, so that it can check whether the MemoryRegion corresponding
to the address is also mapped anywhere else in the AddressSpace and
look for rom blobs that loaded to that alias.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20210318174823.18066-5-peter.maydell@linaro.org
|
|
A clock is added by commit aac63e0e6ea3 ("hw/char/pl011: add a clock
input") since v5.2.0 which corresponds to virt-5.2 machine type. It
causes backwards migration failure from upstream to downstream (v5.1.0)
when the machine type is specified with virt-5.1.
This fixes the issue by following instructions from section "Connecting
subsections to properties" in docs/devel/migration.rst. With this applied,
the PL011 clock is migrated based on the machine type.
virt-5.2 or newer: migration
virt-5.1 or older: non-migration
Cc: qemu-stable@nongnu.org # v5.2.0+
Fixes: aac63e0e6ea3 ("hw/char/pl011: add a clock input")
Suggested-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: Andrew Jones <drjones@redhat.com>
Message-id: 20210318023801.18287-1-gshan@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Since HSS commit c20a89f8dcac, the Icicle Kit reference design has
been updated to use a register mapped at 0x4f000000 instead of a
GPIO to control whether eMMC or SD card is to be used. With this
support the same HSS image can be used for both eMMC and SD card
boot flow, while previously two different board configurations were
used. This is undocumented but one can take a look at the HSS code
HSS_MMCInit() in services/mmc/mmc_api.c.
With this commit, HSS image built from 2020.12 release boots again.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210322075248.136255-1-bmeng.cn@gmail.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
Provides fw_cfg for the virt machine on riscv. This enables
using e.g. ramfb later.
Signed-off-by: Asherah Connor <ashe@kivikakk.ee>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210318235041.17175-2-ashe@kivikakk.ee
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
Not disabling the UART leads to QEMU overwriting the UART receive buffer with
the newest received byte. The rx_level variable is added to allow the use of
the existing OpenTitan driver libraries.
Signed-off-by: Alexander Wagner <alexander.wagner@ulal.de>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210309152130.13038-1-alexander.wagner@ulal.de
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
The code that sets/gets oem fields is duplicated in both PC and MICROVM
variants. This commit moves it to X86MachineState so that all x86
variants can use it and duplication is removed.
Signed-off-by: Marian Postevca <posteuca@mutex.one>
Message-Id: <20210221001737.24499-2-posteuca@mutex.one>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
We want to have safety margins for all tables based on the table type.
Let's move the maximum size logic into acpi_add_rom_blob() and make it
dependent on the table name, so we don't have to replicate for each and
every instance that creates such tables.
Suggested-by: Laszlo Ersek <lersek@redhat.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210304105554.121674-4-david@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The resizeable memory region / RAMBlock that is created for the cmd blob
has a maximum size of whole host pages (e.g., 4k), because RAMBlocks
work on full host pages. In addition, in i386 ACPI code:
acpi_align_size(tables->linker->cmd_blob, ACPI_BUILD_ALIGN_SIZE);
makes sure to align to multiples of 4k, padding with 0.
For example, if our cmd_blob is created with a size of 2k, the maximum
size is 4k - we cannot grow beyond that. Growing might be required
due to guest action when rebuilding the tables, but also on incoming
migration.
This automatic generation of the maximum size used to be sufficient,
however, there are cases where we cross host pages now when growing at
runtime: we exceed the maximum size of the RAMBlock and can crash QEMU when
trying to resize the resizeable memory region / RAMBlock:
$ build/qemu-system-x86_64 --enable-kvm \
-machine q35,nvdimm=on \
-smp 1 \
-cpu host \
-m size=2G,slots=8,maxmem=4G \
-object memory-backend-file,id=mem0,mem-path=/tmp/nvdimm,size=256M \
-device nvdimm,label-size=131072,memdev=mem0,id=nvdimm0,slot=1 \
-nodefaults \
-device vmgenid \
-device intel-iommu
Results in:
Unexpected error in qemu_ram_resize() at ../softmmu/physmem.c:1850:
qemu-system-x86_64: Size too large: /rom@etc/table-loader:
0x2000 > 0x1000: Invalid argument
In this configuration, we consume exactly 4k (32 entries, 128 bytes each)
when creating the VM. However, once the guest boots up and maps the MCFG,
we also create the MCFG table and end up consuming 2 additional entries
(pointer + checksum) -- which is where we try resizing the memory region
/ RAMBlock, however, the maximum size does not allow for it.
Currently, we get the following maximum sizes for our different
mutable tables based on behavior of resizeable RAMBlock:
hw table max_size
------- ---------------------------------------------------------
virt "etc/acpi/tables" ACPI_BUILD_TABLE_MAX_SIZE (0x200000)
virt "etc/table-loader" HOST_PAGE_ALIGN(initial_size)
virt "etc/acpi/rsdp" HOST_PAGE_ALIGN(initial_size)
i386 "etc/acpi/tables" ACPI_BUILD_TABLE_MAX_SIZE (0x200000)
i386 "etc/table-loader" HOST_PAGE_ALIGN(initial_size)
i386 "etc/acpi/rsdp" HOST_PAGE_ALIGN(initial_size)
microvm "etc/acpi/tables" ACPI_BUILD_TABLE_MAX_SIZE (0x200000)
microvm "etc/table-loader" HOST_PAGE_ALIGN(initial_size)
microvm "etc/acpi/rsdp" HOST_PAGE_ALIGN(initial_size)
Let's set the maximum table size for "etc/table-loader" to 64k, so we
can properly grow at runtime, which should be good enough for the future.
Migration is not concerned with the maximum size of a RAMBlock, only
with the used size - so existing setups are not affected. Of course, we
cannot migrate a VM that would have crash when started on older QEMU from
new QEMU to older QEMU without failing early on the destination when
synchronizing the RAM state:
qemu-system-x86_64: Size too large: /rom@etc/table-loader: 0x2000 > 0x1000: Invalid argument
qemu-system-x86_64: error while loading state for instance 0x0 of device 'ram'
qemu-system-x86_64: load of migration failed: Invalid argument
We'll refactor the code next, to make sure we get rid of this implicit
behavior for "etc/acpi/rsdp" as well and to make the code easier to
grasp.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Shannon Zhao <shannon.zhaosl@gmail.com>
Cc: Marcel Apfelbaum <marcel.apfelbaum@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <richard.henderson@linaro.org>
Cc: Laszlo Ersek <lersek@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210304105554.121674-2-david@redhat.com>
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
