aboutsummaryrefslogtreecommitdiff
path: root/include/hw/ssi
AgeCommit message (Collapse)Author
2016-07-12Clean up header guards that don't match their file nameMarkus Armbruster
Header guard symbols should match their file name to make guard collisions less likely. Offenders found with scripts/clean-header-guards.pl -vn. Cleaned up with scripts/clean-header-guards.pl, followed by some renaming of new guard symbols picked by the script to better ones. Signed-off-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Richard Henderson <rth@twiddle.net>
2016-07-04ast2400: add SPI flash slavesCédric Le Goater
Each controller on the ast2400 has a memory range on which it maps its flash module slaves. Each slave is assigned a memory segment for its mapping that can be changed at bootime with the Segment Address Register. This is not supported in the current implementation so we are using the defaults provided by the specs. Each SPI flash slave can then be accessed in two modes: Command and User. When in User mode, accesses to the memory segment of the slaves are translated in SPI transfers. When in Command mode, the HW generates the SPI commands automatically and the memory segment is accessed as if doing a MMIO. Other SPI controllers call that mode linear addressing mode. For this purpose, we are adding below each crontoller an array of structs gathering for each SPI flash module, a segment rank, a MemoryRegion to handle the memory accesses and the associated SPI slave device, which should be a m25p80. Only the User mode is supported for now but we are preparing ground for the Command mode. The framework is sufficient to support Linux. Signed-off-by: Cédric Le Goater <clg@kaod.org> Message-id: 1467138270-32481-8-git-send-email-clg@kaod.org [PMM: Use g_new0() rather than g_malloc0()] Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-07-04ast2400: add SMC controllers (FMC and SPI)Cédric Le Goater
The Aspeed AST2400 soc includes a static memory controller for the BMC which supports NOR, NAND and SPI flash memory modules. This controller has two modes : the SMC for the legacy interface which supports only one module and the FMC for the new interface which supports up to five modules. The AST2400 also includes a SPI only controller used for the host firmware, commonly called BIOS on Intel. It can be used in three mode : a SPI master, SPI slave and SPI pass-through Below is the initial framework for the SMC controller (FMC mode only) and the SPI controller: the sysbus object, MMIO for registers configuration and controls. Each controller has a SPI bus and a configurable number of CS lines for SPI flash slaves. The differences between the controllers are small, so they are abstracted using indirections on the register numbers. Only SPI flash modules are supported. Signed-off-by: Cédric Le Goater <clg@kaod.org> Message-id: 1467138270-32481-7-git-send-email-clg@kaod.org Reviewed-by: Peter Maydell <peter.maydell@linaro.org> [PMM: added one missing error_propagate] Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-07-04ssi: change ssi_slave_init to be a realize opsCédric Le Goater
This enables qemu to handle late inits and report errors. All the SSI slave routine names were changed accordingly. Code was modified to handle errors when possible (m25p80 and ssi-sd) Tested with the m25p80 slave object. Suggested-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Cédric Le Goater <clg@kaod.org> Message-id: 1467138270-32481-2-git-send-email-clg@kaod.org Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-05-12i.MX: Add the Freescale SPI ControllerJean-Christophe DUBOIS
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-01-21xilinx_spips: Separate the state struct into a headerAlistair Francis
Separate out the XilinxSPIPS struct into a separate header file. Signed-off-by: Alistair Francis <alistair.francis@xilinx.com> Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com> Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-01-21ssi: Move ssi.h into a separate directoryAlistair Francis
Move the ssi.h include file into the ssi directory. While touching the code also fix the typdef lines as checkpatch complains. Signed-off-by: Alistair Francis <alistair.francis@xilinx.com> Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com> Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>