| Age | Commit message (Collapse) | Author |
|---|
|
This is a simple model of the POWER9 XIVE interrupt controller for the
PowerNV machine which only addresses the needs of the skiboot
firmware. The PowerNV model reuses the common XIVE framework developed
for sPAPR as the fundamentals aspects are quite the same. The
difference are outlined below.
The controller initial BAR configuration is performed using the XSCOM
bus from there, MMIO are used for further configuration.
The MMIO regions exposed are :
- Interrupt controller registers
- ESB pages for IPIs and ENDs
- Presenter MMIO (Not used)
- Thread Interrupt Management Area MMIO, direct and indirect
The virtualization controller MMIO region containing the IPI ESB pages
and END ESB pages is sub-divided into "sets" which map portions of the
VC region to the different ESB pages. These are modeled with custom
address spaces and the XiveSource and XiveENDSource objects are sized
to the maximum allowed by HW. The memory regions are resized at
run-time using the configuration of EDT set translation table provided
by the firmware.
The XIVE virtualization structure tables (EAT, ENDT, NVTT) are now in
the machine RAM and not in the hypervisor anymore. The firmware
(skiboot) configures these tables using Virtual Structure Descriptor
defining the characteristics of each table : SBE, EAS, END and
NVT. These are later used to access the virtual interrupt entries. The
internal cache of these tables in the interrupt controller is updated
and invalidated using a set of registers.
Still to address to complete the model but not fully required is the
support for block grouping. Escalation support will be necessary for
KVM guests.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The POWER9 PowerNV machine will use a XIVE interrupt presenter type.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The PowerNV machine with need to encode the block id in the source
interrupt number before forwarding the source event notification to
the Router.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The PowerNV machine can perform indirect loads and stores on the TIMA
on behalf of another CPU. Give the controller the possibility to call
the TIMA memory accessors with a XiveTCTX of its choice.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-4-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
We will use it to get the CPU interrupt presenter in XIVE when the
TIMA is accessed from the indirect page.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
SPAPR_MEMORY_BLOCK_SIZE is logically a difference in memory addresses, and
hence of type hwaddr which is 64-bit. Previously it wasn't marked as such
which means that it could be treated as 32-bit. That will work in some
circumstances but if multiplied by another 32-bit value it could lead to
a 32-bit overflow and an incorrect result.
One specific instance of this in spapr_lmb_dt_populate() was spotted by
Coverity (CID 1399145).
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Introduce a new spapr_cap SPAPR_CAP_CCF_ASSIST to be used to indicate
the requirement for a hw-assisted version of the count cache flush
workaround.
The count cache flush workaround is a software workaround which can be
used to flush the count cache on context switch. Some revisions of
hardware may have a hardware accelerated flush, in which case the
software flush can be shortened. This cap is used to set the
availability of such hardware acceleration for the count cache flush
routine.
The availability of such hardware acceleration is indicated by the
H_CPU_CHAR_BCCTR_FLUSH_ASSIST flag being set in the characteristics
returned from the KVM_PPC_GET_CPU_CHAR ioctl.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301031912.28809-2-sjitindarsingh@gmail.com>
[dwg: Small style fixes]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The spapr_cap SPAPR_CAP_IBS is used to indicate the level of capability
for mitigations for indirect branch speculation. Currently the available
values are broken (default), fixed-ibs (fixed by serialising indirect
branches) and fixed-ccd (fixed by diabling the count cache).
Introduce a new value for this capability denoted workaround, meaning that
software can work around the issue by flushing the count cache on
context switch. This option is available if the hypervisor sets the
H_CPU_BEHAV_FLUSH_COUNT_CACHE flag in the cpu behaviours returned from
the KVM_PPC_GET_CPU_CHAR ioctl.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301031912.28809-1-sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Add spapr_cap SPAPR_CAP_LARGE_DECREMENTER to be used to control the
availability of the large decrementer for a guest.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Message-Id: <20190301024317.22137-1-sjitindarsingh@gmail.com>
[dwg: Trivial style fix]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Hotplugging PHBs is a machine-level operation, but PHBs reside on the
main system bus, so we register spapr machine as the handler for the
main system bus.
Provide the usual pre-plug, plug and unplug-request handlers.
Move the checking of the PHB index to the pre-plug handler. It is okay
to do that and assert in the realize function because the pre-plug
handler is always called, even for the oldest machine types we support.
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
(Fixed interrupt controller phandle in "interrupt-map" and
TCE table size in "ibm,dma-window" FDT fragment, Greg Kurz)
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059672926.1466090.13612804072190051439.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Signed-off-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059670389.1466090.10015601248906623076.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This will be used by PHB hotplug in order to create the "interrupt-map"
property of the PHB node.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059669374.1466090.12943228478046223856.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This will be needed by PHB hotplug in order to access the "phandle"
property of the interrupt controller node.
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <155059668867.1466090.6339199751719123386.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The pseries machine only uses LSIs to support legacy PCI devices. Every
PHB claims 4 LSIs at realize time. When using in-kernel XICS (or upcoming
in-kernel XIVE), QEMU synchronizes the state of all irqs, including these
LSIs, later on at machine reset.
In order to support PHB hotplug, we need a way to tell KVM about the LSIs
that doesn't require a machine reset. An easy way to do that is to always
inform KVM when an interrupt is claimed, which really isn't a performance
path.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059668360.1466090.5969630516627776426.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
All DRC subtypes have been converted to generate the FDT fragment at
configure connector time instead of attach time. The fdt and fdt_offset
arguments of spapr_drc_attach() aren't needed anymore. Drop them and
make the implementation of the dt_populate() method mandatory.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059667853.1466090.16527852453054217565.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059666839.1466090.3833376527523126752.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059666331.1466090.6766540766297333313.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The current logic is to provide the FDT fragment when attaching a device
to a DRC. This works perfectly fine for our current hotplug support, but
soon we will add support for PHB hotplug which has some constraints, that
CPU, PCI and LMB devices don't seem to have.
The first constraint is that the "ibm,dma-window" property of the PHB
node requires the IOMMU to be configured, ie, spapr_tce_table_enable()
has been called, which happens during PHB reset. It is okay in the case
of hotplug since the device is reset before the hotplug handler is
called. On the contrary with coldplug, the hotplug handler is called
first and device is only reset during the initial system reset. Trying
to create the FDT fragment on the hotplug path in this case, would
result in somthing like this:
ibm,dma-window = < 0x80000000 0x00 0x00 0x00 0x00 >;
This will cause linux in the guest to panic, by simply removing and
re-adding the PHB using the drmgr command:
page = alloc_pages_node(nid, GFP_KERNEL, get_order(sz));
if (!page)
panic("iommu_init_table: Can't allocate %ld bytes\n", sz);
The second and maybe more problematic constraint is that the
"interrupt-map" property needs to reference the interrupt controller
node using the very same phandle that SLOF has already exposed to the
guest. QEMU requires SLOF to call the private KVMPPC_H_UPDATE_DT hcall
at some point to know about this phandle. With the latest QEMU and SLOF,
this happens when SLOF gets quiesced. This means that if the PHB gets
hotplugged after CAS but before SLOF quiesce, then we're sure that the
phandle is not known when the hotplug handler is called.
The FDT is only needed when the guest first invokes RTAS to configure
the connector actually, long after SLOF quiesce. Let's postpone the
creation of FDT fragments for PHBs to rtas_ibm_configure_connector().
Since we only need this for PHBs, introduce a new method in the base
DRC class for that. DRC subtypes will be converted to use it in
subsequent patches.
Allow spapr_drc_attach() to be passed a NULL fdt argument if the method
is available. When all DRC subtypes have been converted, the fdt argument
will eventually disappear.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155059665823.1466090.18358845122627355537.stgit@bahia.lab.toulouse-stg.fr.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The HW relies on LPCR:HR along with the PATE to determine whether
to use Radix or Hash mode. In fact it uses LPCR:HR more commonly
than the PATE.
For us, it's also more efficient to do so, especially since unlike
the HW we do not maintain a cache of the current PATE and HV PATE
in a generic place.
Prepare the grounds for that by ensuring that LPCR:HR is set
properly on SPAPR machines.
Another option would have been to use a callback to get the PATE
but this gets messy when implementing bare metal support, it's
much simpler (and faster) to use LPCR.
Since existing migration streams may not have it, fix it up in
spapr_post_load() as well based on the pseudo-PATE entry that
we keep.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190215170029.15641-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
On ppc hosts, hypervisor shares following system attributes
- /proc/device-tree/system-id
- /proc/device-tree/model
with a guest. This could lead to information leakage and misuse.[*]
Add machine attributes to control such system information exposure
to a guest.
[*] https://wiki.openstack.org/wiki/OSSN/OSSN-0028
Reported-by: Daniel P. Berrangé <berrange@redhat.com>
Fix-suggested-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <20190218181349.23885-1-ppandit@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Adds support for the Hypervisor directed interrupts in addition to the
OS ones.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[clg: - modified the icp_realize() and xive_tctx_realize() to take
into account explicitely the POWER9 interrupt model
- introduced a specific power9_set_irq for POWER9 ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190215161648.9600-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The KVM ICS class isn't used anymore. Drop it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023084177.1011724.14693955932559990358.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
We want to use the "simple" ICS type in both KVM and non-KVM setups.
Teach the "simple" ICS how to present interrupts to KVM and adapt
sPAPR accordingly.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023082996.1011724.16237920586343905010.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The pre_save(), post_load() and synchronize_state() methods of the
ICSStateClass type are really KVM only things. Make that obvious
by dropping the indirections and directly calling the KVM functions
instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023081817.1011724.14078777320394028836.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The KVM ICP class isn't used anymore. Drop it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023081228.1011724.12474992370439652538.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The base ICP class knows how to interact with KVM. Adapt sPAPR to use it
instead of the ICP KVM class.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023080638.1011724.792095453419098948.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The realization of KVM ICP currently follows the parent_realize logic,
which is a bit overkill here. Also we want to get rid of the KVM ICP
class. Explicitely call icp_kvm_realize() from the base ICP realize
function.
Note that ICPStateClass::parent_realize is retained because powernv
needs it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023080049.1011724.15423463482790260696.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The KVM ICP reset handler simply writes the ICP state to KVM. This
doesn't need the overkill parent_reset logic we have today. Call
icp_set_kvm_state() from the base ICP reset function instead.
Since there are no other users for ICPStateClass::parent_reset, and
it isn't currently expected to change, drop it as well.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023079461.1011724.12644984391500635645.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The pre_save(), post_load() and synchronize_state() methods of the
ICPStateClass type are really KVM only things. Make that obvious
by dropping the indirections and directly calling the KVM functions
instead.
Signed-off-by: Greg Kurz <groug@kaod.org>
Message-Id: <155023078871.1011724.3083923389814185598.stgit@bahia.lan>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
When using the 'dual' interrupt mode, the source numbers of both sPAPR
IRQ backends are aligned to share a common IRQ number space and to use
a similar mapping of the machine qemu_irq array which is indexed by
the source number.
The XICS IRQ number range initially being [ 0x1000 - 0x2000 ], this
requires to change the XICS ICSState offset to 0 and to provision for
an extra 4K of source numbers and qemu_irqs which will never be used
by the machine when running under the XICS interrupt mode. This is not
an optimal solution.
Change the init() method to allocate an IRQ number space of the
expected size for the XICS sPAPR IRQ backend. It breaks the interrupt
signaling when under the 'dual' mode because source numbers have
unexpected values but next patch will fix that.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190213210756.27032-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
MSI is the default and LSI specific code is guarded by the
xive_source_irq_is_lsi() helper. The xive_source_irq_set()
helper is a nop for MSIs.
Simplify the code by turning xive_source_irq_set() into
xive_source_irq_set_lsi() and only call it for LSIs. The
call to xive_source_irq_set(false) in spapr_xive_irq_free()
is also a nop. Just drop it.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <154999584656.690774.18352404495120358613.stgit@bahia.lan>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
All this code is used with both the XICS and XIVE interrupt controllers.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Next step is to remove them from under the PowerPCCPU
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Include the interrupt presenter under the machine_data as we plan to
remove it from under PowerPCCPU
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
It provides a mean to retrieve the XiveTCTX of a CPU. This will become
necessary with future changes which move the interrupt presenter
object pointers under the PowerPCCPU machine_data.
The PowerNV machine has an extra requirement on TIMA accesses that
this new method addresses. The machine can perform indirect loads and
stores on the TIMA on behalf of another CPU. The PIR being defined in
the controller registers, we need a way to peek in the controller
model to find the PIR value.
The XiveTCTX is moved above the XiveRouter definition to avoid forward
typedef declarations.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
To avoid overflow if larger values are added later use ram_addr_t for
the sdram_bank_sizes parameter to match ram_size to which it is compared.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
When compiling the ppc code with clang and -std=gnu99, there are a
couple of warnings/errors like this one:
CC ppc64-softmmu/hw/intc/xics.o
In file included from hw/intc/xics.c:35:
include/hw/ppc/xics.h:43:25: error: redefinition of typedef 'ICPState' is a C11 feature
[-Werror,-Wtypedef-redefinition]
typedef struct ICPState ICPState;
^
target/ppc/cpu.h:1181:25: note: previous definition is here
typedef struct ICPState ICPState;
^
Work around the problems by including the proper headers in spapr.h
and by using struct forward declarations in cpu.h.
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
|
|
When compiling with Clang in -std=gnu99 mode, there is a warning/error:
CC ppc64-softmmu/hw/intc/xics_spapr.o
In file included from /home/thuth/devel/qemu/hw/intc/xics_spapr.c:34:
/home/thuth/devel/qemu/include/hw/ppc/xics.h:203:34: error: redefinition of typedef 'sPAPRMachineState' is a C11 feature
[-Werror,-Wtypedef-redefinition]
typedef struct sPAPRMachineState sPAPRMachineState;
^
/home/thuth/devel/qemu/include/hw/ppc/spapr_irq.h:25:34: note: previous definition is here
typedef struct sPAPRMachineState sPAPRMachineState;
^
We have to remove the duplicated typedef here and include "spapr.h" instead.
But "spapr.h" should not be included for the pnv machine files. So move
the spapr-related prototypes into a new file called "xics_spapr.h" instead.
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
|
|
Depending on the interrupt mode of the machine, enable or disable the
XIVE MMIOs.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The 'dual' sPAPR IRQ backend supports both interrupt mode, XIVE
exploitation mode and the legacy compatibility mode (XICS). both modes
are not supported at the same time.
The machine starts with the legacy mode and a new interrupt mode can
then be negotiated by the CAS process. In this case, the new mode is
activated after a reset to take into account the required changes in
the machine. These impact the device tree layout, the interrupt
presenter object and the exposed MMIO regions in the case of XIVE.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
commit 15ed653fa49a ("ppc/xics: An ICS with offset 0 is assumed to be
uninitialized") introduced an extra check on the ICS offset which is
not strictly necessary.
Revert the change to be able to map the XICS IRQ number space on the
XIVE IRQ number space.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The qemu_irq array is now allocated at the machine level using a sPAPR
IRQ set_irq handler depending on the chosen interrupt mode. The use of
this handler is slightly inefficient today but it will become necessary
when the 'dual' interrupt mode is introduced.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Future changes of the ICSState object will remove the qemu_irq array
from under the interrupt controller model. Prepare ground for the PSI
interrupt sources and introduce a new one directly under the PSI
device model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
To support the 'dual' interrupt mode, XICS and XIVE, we plan to move
the qemu_irq array of each interrupt controller under the machine and
do the allocation under the sPAPR IRQ init method.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Today, the interrupt presenter is linked to a CPU using the
cpu_intc_create() method of the sPAPR IRQ backend. The resulting
object is assigned to the PowerPCCPU 'intc' pointer whatever the
interrupt mode, XICS or XIVE.
To support the 'dual' interrupt mode, we will need to distinguish
between the two presenter objects and for that, we plan to introduce a
second interrupt presenter object pointer under the PowerPCCPU. The
modifications below move the assignment of the presenter object under
the cpu_intc_create() method to prepare ground for the future changes.
Both sPAPR and PowerNV machines are impacted.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The qirq routines of the XiveSource and the sPAPRXive model are only
used under the sPAPR IRQ backend. Simplify the overall call stack and
gather all the code under spapr_qirq_xive(). It will ease future
changes.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
SLOF receives a device tree and updates it with various properties
before switching to the guest kernel and QEMU is not aware of any changes
made by SLOF. Since there is no real RTAS (QEMU implements it), it makes
sense to pass the SLOF final device tree to QEMU to let it implement
RTAS related tasks better, such as PCI host bus adapter hotplug.
Specifially, now QEMU can find out the actual XICS phandle (for PHB
hotplug) and the RTAS linux,rtas-entry/base properties (for firmware
assisted NMI - FWNMI).
This stores the initial DT blob in the sPAPR machine and replaces it
in the KVMPPC_H_UPDATE_DT (new private hypercall) handler.
This adds an @update_dt_enabled machine property to allow backward
migration.
SLOF already has a hypercall since
https://github.com/aik/SLOF/commit/e6fc84652c9c0073f9183
This makes use of the new fdt_check_full() helper. In order to allow
the configure script to pick the correct DTC version, this adjusts
the DTC presense test.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
H_HOME_NODE_ASSOCIATIVITY H-Call returns the associativity domain
designation associated with the identifier input parameter
This fixes a crash when we try to hotplug a CPU in memory-less and
CPU-less numa node. In this case, the kernel tries to online the
node, but without the information provided by this h-call, the node id,
it cannot and the CPU is started while the node is not onlined.
It also removes the warning message from the kernel:
VPHN is not supported. Disabling polling..
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This option is used to select the interrupt controller mode (XICS or
XIVE) with which the machine will operate. XICS being the default
mode for now.
When running a machine with the XIVE interrupt mode backend, the guest
OS is required to have support for the XIVE exploitation mode. In the
case of legacy OS, the mode selected by CAS should be XICS and the OS
should fail to boot. However, QEMU could possibly detect it, terminate
the boot process and reset to stop in the SLOF firmware. This is not
yet handled.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
