| Age | Commit message (Collapse) | Author |
|---|
|
Qemu already supports devices attached to ISA and sysbus. This drop adds
support for the I2C bus attached TPM devices.
This commit includes changes for the common code.
- Added support for the new checksum registers which are required for
the I2C support. The checksum calculation is handled in the qemu
common code.
- Added wrapper function for read and write data so that I2C code can
call it without MMIO interface.
The TPM TIS I2C spec describes in the table in section "Interface Locality
Usage per Register" that the TPM_INT_ENABLE and TPM_INT_STATUS registers
must be writable for any locality even if the locality is not the active
locality. Therefore, remove the checks whether the writing locality is the
active locality for these registers.
Signed-off-by: Ninad Palsule <ninad@linux.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Message-id: 20230414220754.1191476-3-ninadpalsule@us.ibm.com
|
|
Cc: M: Michael S. Tsirkin <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210614191335.1968807-4-stefanb@linux.ibm.com>
Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com>
|
|
The TPM Physical Presence interface consists of an ACPI part, a shared
memory part, and code in the firmware. Users can send messages to the
firmware by writing a code into the shared memory through invoking the
ACPI code. When a reboot happens, the firmware looks for the code and
acts on it by sending sequences of commands to the TPM.
This patch adds the ACPI code. It is similar to the one in EDK2 but doesn't
assume that SMIs are necessary to use. It uses a similar datastructure for
the shared memory as EDK2 does so that EDK2 and SeaBIOS could both make use
of it. I extended the shared memory data structure with an array of 256
bytes, one for each code that could be implemented. The array contains
flags describing the individual codes. This decouples the ACPI implementation
from the firmware implementation.
The underlying TCG specification is accessible from the following page.
https://trustedcomputinggroup.org/tcg-physical-presence-interface-specification/
This patch implements version 1.30.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
[ Marc-André - ACPI code improvements and windows fixes ]
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
To avoid having to hard code the base address of the PPI virtual
memory device we introduce a fw_cfg file etc/tpm/config that holds the
base address of the PPI device, the version of the PPI interface and
the version of the attached TPM.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
[ Marc-André: renamed to etc/tpm/config, made it static, document it ]
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Implement a virtual memory device for the TPM Physical Presence interface.
The memory is located at 0xFED45000 and used by ACPI to send messages to the
firmware (BIOS) and by the firmware to provide parameters for each one of
the supported codes.
This interface should be used by all TPM devices on x86 and can be
added by calling tpm_ppi_init_io().
Note: bios_linker cannot be used to allocate the PPI memory region,
since the reserved memory should stay stable across reboots, and might
be needed before the ACPI tables are installed.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
It eases code review, unit is explicit.
Patch generated using:
$ git grep -E '(1024|2048|4096|8192|(<<|>>).?(10|20|30))' hw/ include/hw/
and modified manually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20180625124238.25339-13-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Move the TPM TIS related register and flag #defines into
include/hw/acpi/tpm.h for access by the test case.
Write a test case that covers the TIS functionality.
Add the tests cases to the MAINTAINERS file.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
|
|
tpm_crb is a device for TPM 2.0 Command Response Buffer (CRB)
Interface as defined in TCG PC Client Platform TPM Profile (PTP)
Specification Family “2.0” Level 00 Revision 01.03 v22.
The PTP allows device implementation to switch between TIS and CRB
model at run time, but given that CRB is a simpler device to
implement, I chose to implement it as a different device.
The device doesn't implement other locality than 0 for now (my laptop
TPM doesn't either, so I assume this isn't so bad)
Tested with some success with Linux upstream and Windows 10, seabios &
modified ovmf. The device is recognized and correctly transmit
command/response with passthrough & emu. However, we are missing PPI
ACPI part atm.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
|
|
Add a TPM2 ACPI table if a TPM 2 is used in the backend.
Also add an SSDT for the TPM 2.
Rename tpm_find() to tpm_get_version() and have this function
return the version of the TPM found, TPMVersion_Unspec if
no TPM is found. Use the version number to build version
specific ACPI tables.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Add an SSDT ACPI table for the TPM device.
Add a TCPA table for BIOS logging area when a TPM is being used.
The latter follows this spec here:
http://www.trustedcomputinggroup.org/files/static_page_files/DCD4188E-1A4B-B294-D050A155FB6F7385/TCG_ACPIGeneralSpecification_PublicReview.pdf
This patch has Michael Tsirkin's patches folded in.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
|
