| Age | Commit message (Collapse) | Author |
|---|
|
According to PLIC specification (chapter 5), there
is only one case, when interrupt is claimed. Fix
PLIC controller to match this behavior.
Signed-off-by: Sergey Makarov <s.makarov@syntacore.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240918140229.124329-3-s.makarov@syntacore.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
According to PLIC specification chapter 4, zeroth
priority register is reserved. Discard writes to
this register.
Signed-off-by: Sergey Makarov <s.makarov@syntacore.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240918140229.124329-2-s.makarov@syntacore.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
RV32 OpenSBI need a fw_dynamic_info parameter with 32-bit fields instead
of target_ulong.
In RV64 QEMU, target_ulong is 64. So it is not right for booting RV32 OpenSBI.
We create a fw_dynmaic_info32 struct for this purpose.
Signed-off-by: TANG Tiancheng <tangtiancheng.ttc@alibaba-inc.com>
Reviewed-by: Liu Zhiwei <zhiwei_liu@linux.alibaba.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240919055048.562-2-zhiwei_liu@linux.alibaba.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
We computes indirections_len by adding 1 to indirection_table_mask, but
it may overflow indirection_table_mask is UINT16_MAX. Check if
indirection_table_mask is small enough before adding 1.
Fixes: 590790297c0d ("virtio-net: implement RSS configuration command")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
This adds more trace events to key eBPF RSS setup operations, and
also distinguishes events from multiple NIC instances.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
If the user/mgmt app passed in a set of pre-opened FDs for eBPF RSS,
then it is expecting QEMU to use them. Any failure to do so must be
considered a fatal error and propagated back up the stack, otherwise
deployment mistakes will not be detectable in a prompt manner. When
not using pre-opened FDs, then eBPF RSS is tried on a "best effort"
basis only and thus fallback to software RSS is valid.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
The eBPF code is currently reporting error messages through trace
events. Trace events are fine for debugging, but they are not to be
considered the primary error reporting mechanism, as their output
is inaccessible to callers.
This adds an "Error **errp" parameter to all methods which have
important error scenarios to report to the caller.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
staging
aspeed queue:
* Fixed GPIO interrupt status when in index mode
* Added GPIO support for the AST2700 SoC and specific test cases
* Fixed crypto controller (HACE) Accumulative hash function
* Converted Aspeed machine avocado tests to the new functional
framework. SDK tests still to be addressed.
* Fixed issue in the SSI controller when doing writes in user mode
* Added support for the WRSR2 register of Winbond flash devices
* Added SFDP table for the Windbond w25q80bl flash device
* Changed flash device models for the ast1030-a1 EVB
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmcZ6MIACgkQUaNDx8/7
# 7KFQPA//RTxi1PmCDlzd1ffzMWEadD3CpGLJ4RgEeZpNtkx6IF2uFFBdlNgjTSmD
# B8FdIOVb8qo2omXahKIVIgoKbGgn3U3jciH67D/x4Jyp8IhW6n5XwZzKNJ7kLVHX
# IluGmlvqNumSKl3vxsLvprC0ojRiO/SfWkzS6VOwoFPM7uNDTybQicWBBoy3Jh3e
# VVlMwIeKHMQVJGpI8PQbtnFZO4HaMqWwlo0EoIJji59fdyWULLvrXzH9YhzwFVjQ
# oCNvJUBLfxLse7c13cm/LuNmw+IQtLC5OztsOOtv1XZ1MruhJ7t316eGsQEpeWcD
# Yy5RK4mIBJMExu9oxcKOqgSznQSgenvNGWg6Z9FyyKGciylafnE8GeT35WObumyD
# v9gzgeLcw5DgvDgQXaYi4IkKyezaHoE3HPbFdBEZHBt8tn5pPGmXM0lEWL5xQ5B8
# h6HphjxIlFxeHIxYenLJowLBMOt8aFXzGboF2XCLrx19OC2zvoo7klCbFeAfZpvQ
# JMXP+GsQIe7fnBMbyXGrJh9q+/7tKR4ivtTV/vnSF0FPtyzxdoSrYsUA4SZqSWvI
# ONz62p+zlE/oXBUIaFnC2Ea41YwJ7mDbmcSU1dFxmE0xRVmoYlUocoeS2VOUmTH0
# CMgEcmMXQG0vx8nipQbScbuWRCBlf0YwJ7Y7stgI8HabmsMMbIg=
# =DqCH
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 24 Oct 2024 07:27:14 BST
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@redhat.com>" [full]
# gpg: aka "Cédric Le Goater <clg@kaod.org>" [full]
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-aspeed-20241024' of https://github.com/legoater/qemu:
test/qtest/aspeed_smc-test: Fix coding style
hw/arm/aspeed: Correct fmc_model w25q80bl for ast1030-a1 EVB
hw/arm/aspeed: Correct spi_model w25q256 for ast1030-a1 EVB.
hw/block/m25p80: Add SFDP table for w25q80bl flash
hw/block:m25p80: Support write status register 2 command (0x31) for w25q01jvq
hw/block:m25p80: Fix coding style
aspeed/smc: Fix write incorrect data into flash in user mode
tests/functional: Convert most Aspeed machine tests
hw/misc/aspeed_hace: Fix SG Accumulative hashing
tests/qtest:ast2700-gpio-test: Add GPIO test case for AST2700
aspeed/soc: Support GPIO for AST2700
aspeed/soc: Correct GPIO irq 130 for AST2700
hw/gpio/aspeed: Add AST2700 support
hw/gpio/aspeed: Fix clear incorrect interrupt status for GPIO index mode
hw/gpio/aspeed: Support different memory region ops
hw/gpio/aspeed: Support to set the different memory size
hw/gpio/aspeed: Fix coding style
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
vfio queue:
* Fixed size reported in vfio_state_pending_exact()
* Added support for PMD or PUD aligned mappings
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmcZ22wACgkQUaNDx8/7
# 7KHU5g/8Cr1487IJQb5cbpLu2Nviu3wjzhbCFFdbl99uLifdc0GK1P6fqDNQ7BVx
# 2vpZgJRXLTxlUSTpreFw4z6TH7/C4HoNiluQV4l0vxqG/Y9q68SJBpT9WENwXUyY
# +2laDmGQbUjDznxIFlmCgZZAssCIJNp0esNE9hvwkQCarZx9m+QQSSkeVHVWNFqX
# +zTd4v076Q9hi53+4e7FlqFKaFoa54IcZe3gz+GjY/IXMqCDNFw9e9xJxML+zSg3
# HZ4/YMQj+EsKX2gm460EYBmt13kd0wdtFzA1MNc7XcSlBlLk/WmezpEzHZRubiLs
# mbUZ68/cweJmrO0WatycWg9JwQ2q9FlKH1Acgun4Fcf8Zov5ovHuYAsWYbdGDbN1
# E7pY/XlUf6b7Vk+yAGTnKKRi6OguTEmVyRRFy/4V8TwvZNycbeOMebKilGQUGfKj
# iLWuzF6NilT4ZGo7sWnlLZWcmrxN57wJh77GlmcqiqguskB8WGdh/SZSVCkkzr3y
# PN3FGSTseNaxalcjECEFnfE8+bUShLei+I6fppTfqLBaLHJ72lRel0Cg07FS8oM4
# 3ev7etH7jFT5xET00DBamDXacgNtLqFqO6XIK3bFTkLmP0FFQi9u+bvy04IyTVCC
# gd9Zg2vhxp0mjuwtelB+i7yD3pmA2LWFkEzoShpkH/h38CnpoyQ=
# =+69I
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 24 Oct 2024 06:30:20 BST
# gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1
# gpg: Good signature from "Cédric Le Goater <clg@redhat.com>" [full]
# gpg: aka "Cédric Le Goater <clg@kaod.org>" [full]
# Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1
* tag 'pull-vfio-20241024' of https://github.com/legoater/qemu:
vfio/helpers: Align mmaps
vfio/helpers: Refactor vfio_region_mmap() error handling
vfio/migration: Change trace formats from hex to decimal
vfio/migration: Report only stop-copy size in vfio_state_pending_exact()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
staging
* Allow multiple boot devices (via bootindex properties) on s390x
* Avoid TEXTREL relocations in the s390-ccw.img firmware
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmcY9vsRHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbWnBQ//eM0RPHgp3OCbCy42HYp569RdHvXE69BS
# 7iO8uu7MGRKIAHJqqmDwFDfhfMtoJkfjq9bQpb+pmIUe50r2NAC9na9+bjIc2bK+
# sxHvS5PTZiQcPOiGwAmp3lEheFPWi6sugYVruO+6syGLJdoa39Vnj71pF86lJ6dk
# HFltOqa0lG3YWzueKXInLQnpRaIvPzjJVEUuNRk5H6ai0woItWvrPK82HMcKXSu5
# mwJiGP2dmwvZw3nC8GsNKbxxZNc2gEM6tFFozbsaE/Yfzmg/S4kHexzjSGd7svT7
# kex65F9aqiK3x1WrWwuCCU6D8qEkNqzXezNlmedvgcMokkdd8Xwlqvw2Ng3sbF7i
# 466jEdq0CuAiEhO6AvSYrEDpI8trWxj4EtxcjfqltUVR/SYFcW9hRdx99VwrRCo2
# woazKmHz7Hu6uS5+JPtfD+KxalIDXNXevY6uGyaWJp8TahDkUCim/gJ+Zb7Mx1iq
# Vrx/rCm1oV8v1xrn8NWTGewA8emVjbLI3PuDtPh9FWRpER7ekn+dDUinzeUl2wWK
# +USqIE2ougo1etRm7FAkyWEv9F/GjGTd8OegIGD6etWBNBq/YVMNwX1gjw4Q0qhM
# +7KmXLBKkuEBYSo4scSGt6DcasIUL93sc6rnWgiH3S/qMAYyKempKPkoROYQI8yA
# 0EI+x1fxW1w=
# =mWW5
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 23 Oct 2024 14:15:39 BST
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2024-10-23' of https://gitlab.com/thuth/qemu: (23 commits)
pc-bios/s390-ccw: Update s390-ccw.img with the full boot order support feature
pc-bios/s390-ccw: Introduce `EXTRA_LDFLAGS`
pc-bios/s390-ccw: Don't generate TEXTRELs
pc-bios/s390-ccw: Clarify alignment is in bytes
tests/qtest: Add s390x boot order tests to cdrom-test.c
docs/system: Update documentation for s390x IPL
pc-bios/s390x: Enable multi-device boot loop
s390x: Rebuild IPLB for SCSI device directly from DIAG308
hw/s390x: Build an IPLB for each boot device
s390x: Add individual loadparm assignment to CCW device
include/hw/s390x: Add include files for common IPL structs
pc-bios/s390-ccw: Enable failed IPL to return after error
pc-bios/s390-ccw: Remove panics from Netboot IPL path
pc-bios/s390-ccw: Remove panics from DASD IPL path
pc-bios/s390-ccw: Remove panics from SCSI IPL path
pc-bios/s390-ccw: Remove panics from ECKD IPL path
pc-bios/s390-ccw: Remove panics from ISO IPL path
docs/system/s390x/bootdevices: Update the documentation about network booting
pc-bios/s390-ccw: Merge netboot.mak into the main Makefile
hw/s390x: Remove the possibility to load the s390-netboot.img binary
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Currently, the default fmc_model was "sst25vf032b" whose size was 4MB for
ast1030-a1 EVB. However, according to the schematic of ast1030-a1 EVB,
ASPEED shipped default flash of fmc_cs0 and fmc_cs1 were "w25q80bl" and
"w25q256", respectively. The size of w25q80bl is 1MB and the size of w25q256
is 32MB.
The fmc_cs0 was connected to AST1030 A1 internal flash and the fmc_cs1 was
connected to external flash. The internal flash could not be changed because
it was placed into AST1030 A1 chip. Users only can change fmc_cs1 external
flash.
So far, only supports to set the default fmc_model for all chip select pins.
In other words, users cannot set the different default flash model for
fmc_cs0 and fmc_cs1, respectively.
Correct fmc_model default flash to w25q80bl the same as AST1030 A1
internal flash for ast1030-a1 EVB.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
|
|
Currently, the default spi_model was "sst25vf032b" whose size was 4MB for
ast1030-a1 EVB. However, according to the schematic of ast1030-a1 EVB,
ASPEED shipped default flash of spi1 and spi2 were w25q256 whose size
was 32MB.
Correct spi_model default flash to w25q256 for ast1030-a1 EVB.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
|
|
Add the SFDP table for the Windbond w25q80bl flash.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
|
|
According to the w25q01jv datasheet at page 16, it is required to set QE bit
in "Status Register 2" to enable quad mode.
Currently, m25p80 support users utilize "Write Status Register 1(0x01)" command
to set QE bit in "Status Register 2" and utilize "Read Status Register 2(0x35)"
command to get the QE bit status.
However, some firmware directly utilize "Status Register 2(0x31)" command to
set QE bit. To fully support quad mode for w25q01jvq, adds WRSR2 command.
Update collecting data needed 1 byte for WRSR2 command in decode_new_cmd
function and verify QE bit at the first byte of collecting data bit 2 in
complete_collecting_data.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
|
|
Fix coding style issues from checkpatch.pl
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
|
|
According to the design of ASPEED SPI controllers user mode, users write the
data to flash, the SPI drivers set the Control Register(0x10) bit 0 and 1
enter user mode. Then, SPI drivers send flash commands for writing data.
Finally, SPI drivers set the Control Register (0x10) bit 2 to stop
active control and restore bit 0 and 1.
According to the design of ASPEED SMC model, firmware writes the
Control Register and the "aspeed_smc_flash_update_ctrl" function is called.
Then, this function verify Control Register(0x10) bit 0 and 1. If it set user
mode, the value of s->snoop_index is SNOOP_START else SNOOP_OFF.
If s->snoop_index is SNOOP_START, the "aspeed_smc_do_snoop" function verify
the first incomming data is a new flash command and writes the corresponding
dummy bytes if need.
However, it did not check the current unselect status. If current unselect
status is "false" and firmware set the IO MODE by Control Register bit 31:28,
the value of s->snoop_index will be changed to SNOOP_START again and
"aspeed_smc_do_snoop" misunderstand that the incomming data is the new flash
command and it causes writing unexpected data into flash.
Example:
1. Firmware set user mode by Control Register bit 0 and 1(0x03)
2. SMC model set s->snoop SNOOP_START
3. Firmware set Quad Page Program with 4-Byte Address command (0x34)
4. SMC model verify this flash command and it needs 4 dummy bytes.
5. Firmware send 4 bytes address.
6. SMC model receives 4 bytes address
7. Firmware set QPI IO MODE by Control Register bit 31. (0x80000003)
8. SMC model verify new user mode by Control Register bit 0 and 1.
Then, set s->snoop SNOOP_START again. (It is the wrong behavior.)
9. Firmware send 0xebd8c134 data and it should be written into flash.
However, SMC model misunderstand that the first incoming data, 0x34,
is the new command because the value of s->snoop is changed to SNOOP_START.
Finally, SMC sned the incorrect data to flash model.
Introduce a new unselect attribute in AspeedSMCState to save the current
unselect status for user mode and set it "true" by default.
Update "aspeed_smc_flash_update_ctrl" function to check the previous unselect
status. If both new unselect status and previous unselect status is different,
update s->snoop_index value and call "aspeed_smc_flash_do_select".
Increase VMStateDescription version.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
[ clg: - Replaced VMSTATE_BOOL -> VMSTATE_BOOL_V ]
Signed-off-by: Cédric Le Goater <clg@redhat.com>
|
|
Make the Aspeed HACE module use the new qcrypto accumulative hashing functions
when in scatter-gather accumulative mode. A hash context will maintain a
"running-hash" as each scatter-gather chunk is received.
Previously each scatter-gather "chunk" was cached
so the hash could be computed once the final chunk was received.
However, the cache was a shallow copy, so once the guest overwrote the
memory provided to HACE the final hash would not be correct.
Possibly related to: https://gitlab.com/qemu-project/qemu/-/issues/1121
Buglink: https://github.com/openbmc/qemu/issues/36
Signed-off-by: Alejandro Zeise <alejandro.zeise@seagate.com>
[ clg: - Checkpatch fixes
- Reworked qcrypto_hash*() error reports in do_hash_operation() ]
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Acked-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
|
|
Add GPIO model for AST2700 GPIO support. The GPIO controller registers base
address is start at 0x14C0_B000 and its address space is 0x1000.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
|
|
The register set of GPIO have a significant change since AST2700.
Each GPIO pin has their own individual control register and users are able to
set one GPIO pin’s direction, interrupt enable, input mask and so on in the
same one control register.
AST2700 does not have GPIO18_XXX registers for GPIO 1.8v, removes
ASPEED_DEV_GPIO_1_8V. It is enough to only have ASPEED_DEV_GPIO
device in AST2700.
The AST2700 GPIO controller interrupt is connected to GICINT130_INTC at
bit 18. Therefore, correct GPIO irq 130.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
|
|
AST2700 integrates two set of Parallel GPIO Controller with maximum 212
control pins, which are 27 groups. (H, exclude pin: H7 H6 H5 H4)
In the previous design of ASPEED SOCs, one register is used for setting
one function for one set which are 32 pins and 4 groups.
ex: GPIO000 is used for setting data value for GPIO A, B, C and D in AST2600.
ex: GPIO004 is used for setting direction for GPIO A, B, C and D in AST2600.
However, the register set have a significant change since AST2700.
Each GPIO pin has their own individual control register.
In other words, users are able to set one GPIO pin’s direction,
interrupt enable, input mask and so on in the same one register.
Currently, aspeed_gpio_read and aspeed_gpio_write callback functions
are not compatible AST2700.
Introduce new aspeed_gpio_2700_read and aspeed_gpio_2700_write callback
functions and aspeed_gpio_2700_ops memory region operation for AST2700.
Introduce a new ast2700 class to support AST2700.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
|
|
The interrupt status field is W1C, where a set bit on read indicates an
interrupt is pending. If the bit extracted from data is set it should
clear the corresponding bit in reg_value. However, if the extracted
bit is clear then the value of the corresponding bit in reg_value
should be unchanged.
SHARED_FIELD_EX32() extracts the interrupt status bit from the write
(data). reg_value is set to the set's interrupt status, which means
that for any pin with an interrupt pending, the corresponding bit is
set. The deposit32() call updates the bit at pin_idx in the
reg_value, using the value extracted from the write (data).
The result is that if multiple interrupt status bits
were pending and the write was acknowledging specific one bit,
then the all interrupt status bits will be cleared.
However, it is index mode and should only clear the corresponding bit.
For example, say we have an interrupt pending for GPIOA0, where the
following statements are true:
set->int_status == 0b01
s->pending == 1
Before it is acknowledged, an interrupt becomes pending for GPIOA1:
set->int_status == 0b11
s->pending == 2
A write is issued to acknowledge the interrupt for GPIOA0. This causes
the following sequence:
reg_value == 0b11
pending == 2
s->pending == 0
set->int_status == 0b00
It should only clear bit 0 in index mode and the correct result
should be as following.
set->int_status == 0b11
s->pending == 2
pending == 1
s->pending == 1
set->int_status == 0b10
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Suggested-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Reviewed-by: Andrew Jeffery <andrew@codeconstruct.com.au>
|
|
It set "aspeed_gpio_ops" struct which containing read and write callbacks
to be used when I/O is performed on the GPIO region.
Besides, in the previous design of ASPEED SOCs, one register is used for
setting one function for 32 GPIO pins.
ex: GPIO000 is used for setting data value for GPIO A, B, C and D in AST2600.
ex: GPIO004 is used for setting direction for GPIO A, B, C and D in AST2600.
However, the register set have a significant change in AST2700.
Each GPIO pin has their own control register. In other words, users are able to
set one GPIO pin’s direction, interrupt enable, input mask and so on
in one register. The aspeed_gpio_read/aspeed_gpio_write callback functions
are not compatible AST2700.
Introduce a new "const MemoryRegionOps *" attribute in AspeedGPIOClass and
use it in aspeed_gpio_realize function.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
|
|
According to the datasheet of ASPEED SOCs, a GPIO controller owns 4KB of
register space for AST2700, AST2500, AST2400 and AST1030; owns 2KB of
register space for AST2600 1.8v and owns 2KB of register space for
AST2600 3.3v.
It set the memory region size 2KB by default and it does not compatible
register space for AST2700.
Introduce a new class attribute to set the GPIO controller memory size
for different ASPEED SOCs.
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
|
|
Fix coding style issues from checkpatch.pl
Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
|
|
Thanks to work by Peter Xu, support is introduced in Linux v6.12 to
allow pfnmap insertions at PMD and PUD levels of the page table. This
means that provided a properly aligned mmap, the vfio driver is able
to map MMIO at significantly larger intervals than PAGE_SIZE. For
example on x86_64 (the only architecture currently supporting huge
pfnmaps for PUD), rather than 4KiB mappings, we can map device MMIO
using 2MiB and even 1GiB page table entries.
Typically mmap will already provide PMD aligned mappings, so devices
with moderately sized MMIO ranges, even GPUs with standard 256MiB BARs,
will already take advantage of this support. However in order to better
support devices exposing multi-GiB MMIO, such as 3D accelerators or GPUs
with resizable BARs enabled, we need to manually align the mmap.
There doesn't seem to be a way for userspace to easily learn about PMD
and PUD mapping level sizes, therefore this takes the simple approach
to align the mapping to the power-of-two size of the region, up to 1GiB,
which is currently the maximum alignment we care about.
Cc: Peter Xu <peterx@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
|
|
Move error handling code to the end of the function so that it can more
easily be shared by new mmap failure conditions. No functional change
intended.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
|
|
Data sizes in VFIO migration trace events are printed in hex format
while in migration core trace events they are printed in decimal format.
This inconsistency makes it less readable when using both trace event
types. Hence, change the data sizes print format to decimal in VFIO
migration trace events.
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
|
|
vfio_state_pending_exact() is used to update migration core how much
device data is left for the device migration. Currently, the sum of
pre-copy and stop-copy sizes of the VFIO device are reported.
The pre-copy size is obtained via the VFIO_MIG_GET_PRECOPY_INFO ioctl,
which returns the amount of device data available to be transferred
while the device is in the PRE_COPY states.
The stop-copy size is obtained via the VFIO_DEVICE_FEATURE_MIG_DATA_SIZE
ioctl, which returns the total amount of device data left to be
transferred in order to complete the device migration.
According to the above, current implementation is wrong -- it reports
extra overlapping data because pre-copy size is already contained in
stop-copy size. Fix it by reporting only stop-copy size.
Fixes: eda7362af959 ("vfio/migration: Add VFIO migration pre-copy support")
Signed-off-by: Avihai Horon <avihaih@nvidia.com>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
|
|
Because virtio-scsi type devices use a non-architected IPLB pbt code they cannot
be set and stored normally. Instead, the IPLB must be rebuilt during re-ipl.
As s390x does not natively support multiple boot devices, the devno field is
used to store the position in the boot order for the device.
Handling the rebuild as part of DIAG308 removes the need to check the devices
for invalid IPLBs later in the IPL.
Signed-off-by: Jared Rossi <jrossi@linux.ibm.com>
Acked-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20241020012953.1380075-17-jrossi@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
|
|
Build an IPLB for any device with a bootindex (up to a maximum of 8 devices).
The IPLB chain is placed immediately before the BIOS in memory. Because this
is not a fixed address, the location of the next IPLB and number of remaining
boot devices is stored in the QIPL global variable for possible later access by
the guest during IPL.
Signed-off-by: Jared Rossi <jrossi@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20241020012953.1380075-16-jrossi@linux.ibm.com>
[thuth: Fix endianness problem when accessing the qipl structure]
Signed-off-by: Thomas Huth <thuth@redhat.com>
|
|
Add a loadparm property to the VirtioCcwDevice object so that different
loadparms can be defined on a per-device basis for CCW boot devices.
The machine/global loadparm is still supported. If both a global and per-device
loadparm are defined, the per-device value will override the global value for
that device, but any other devices that do not specify a per-device loadparm
will still use the global loadparm.
It is invalid to assign a loadparm to a non-boot device.
Signed-off-by: Jared Rossi <jrossi@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20241020012953.1380075-15-jrossi@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
|
|
Currently, structures defined in both hw/s390x/ipl.h and pc-bios/s390-ccw/iplb.h
must be kept in sync, which is prone to error. Instead, create a new directory
at include/hw/s390x/ipl/ to contain the definitions that must be shared.
Signed-off-by: Jared Rossi <jrossi@linux.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20241020012953.1380075-14-jrossi@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
|
|
Since the netboot code has now been merged into the main s390-ccw.img
binary, we don't need the separate s390-netboot.img anymore. Remove
it and the code that was responsible for loading it.
Message-Id: <20240621082422.136217-6-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
|
|
We are going to link the SLOF libc into the s390-ccw.img, and this
libc needs more memory for providing space for malloc() and friends.
Thus bump the memory size that we reserve for the bios to 3 MiB
instead of only 2 MiB. While we're at it, add a proper check that
there is really enough memory assigned to the machine before blindly
using it.
Message-ID: <20240621082422.136217-3-thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
|
|
trivial patches for 2024-10-22
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCgAdFiEEZKoqtTHVaQM2a/75gqpKJDselHgFAmcXQugACgkQgqpKJDse
# lHjSfg//ZVmwp7zuGJC6dFwgCIoVc1IqERliuiBQNosw/IYSPwt6S4+lECR6Hu+N
# 4ktKAO6MKwQgBDoqw9Wz+lDASHKJ3VbDkyxfE4wfOz7C1UrCxGEsUzy43wI3Ms5J
# fM175GWTQZiJZkmf0hLmRKtgmouq7YbjPqPvCQTQP/NT8k6f2KiY+YKLmo2cMoUJ
# Ra+JPOKMTQhGTCCOtijdK/6whtUuym7X6hW3LaXC8cjehfwE+dRf7gcApZG8fcKE
# 1ALFbXRlRL+FFM5GfsWr39rtJI0XXdm8fa+dIOuXJQe8X9xns/Ha8fLqiKVo+9k+
# Axk+B2xFopIf6CBPxfXyxzcDnx5KBhIIO86D/M+rSK+pqTaNYcad8OY9ciSBQien
# EgDJDp8DtM6gmY0xa7kMXEKy127l4DWlIp2bM3Ufuv3r5+FS1tSsz5Tfx/d9LRfV
# JPt/9Xl/gW5XAB3+HEc7nkP+/YW4C79nZbkxEYiDIFKa9SrAxbBkuTPGzReAly4y
# zUAaxk0qbtqfYrufz1oiEz3eCoY7zTmey015AfMPwQMHhqPIAYOjv6bwYVOzVTFj
# Vh7xhS+qn/iLDhEB10XqOALIuQu+PCtQjIwHakwGD0IEjG0G1b363p3eYO/+UpDl
# E3ydNh/K61/oCvQJcAJM0lY3KdlVxDCY499KwNDAjSnZL8i8gFY=
# =zFvF
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 22 Oct 2024 07:15:04 BST
# gpg: using RSA key 64AA2AB531D56903366BFEF982AA4A243B1E9478
# gpg: Good signature from "Michael Tokarev <mjt@debian.org>" [full]
# gpg: aka "Michael Tokarev <mjt@corpit.ru>" [full]
# gpg: aka "Michael Tokarev <mjt@tls.msk.ru>" [full]
# Primary key fingerprint: 9D8B E14E 3F2A 9DD7 9199 28F1 61AD 3D98 ECDF 2C8E
# Subkey fingerprint: 64AA 2AB5 31D5 6903 366B FEF9 82AA 4A24 3B1E 9478
* tag 'pull-trivial-patches' of https://gitlab.com/mjt0k/qemu:
replace error_setg(&error_fatal, ...) with error_report()
meson.build: Remove ncurses workaround for OpenBSD
configure: Replace literally printed '\n' with newline
ui/console-vc: Silence warning about sprintf() on OpenBSD
linux-user: Clean up unused header
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
According to include/qapi/error.h:
* Please don't error_setg(&error_fatal, ...), use error_report() and
* exit(), because that's more obvious.
Patch updates all instances of error_setg(&error_fatal, ...) with
error_report(...), adds the explicit exit(1) and removes redundant
return statements.
Signed-off-by: Tudor Gheorghiu <tudor.reda@gmail.com>
Suggested-by: Thomas Huth <thuth@redhat.com>
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2587
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
(Mjt: also fold __func__ to previous line)
|
|
staging
* Convert most Tuxrun Avocado tests to the new functional framework
* Update the OpenBSD CI image to OpenBSD v7.6
* Bump timeout of the ide-test
* New maintainer for the QTests
* Disable the pci-bridge on s390x by default
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmcWfCgRHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbV6kQ//YwRebyA192IBM+XQK5YYmguieHmWxV8J
# fZf0a1dWN8oiT3jzI48YWttiU9P6AMa/dwiuepVl4G9+d+w1c3RhS6kQqJljNbDb
# NGw+LVZZcwY1FJpEsEwbDfePkugYHmNXUU672kxz3I8bv/8NmLDc7R3cI5U/7+SP
# N4lxVM6Hd3XZZdc+O2S8En20E1oAJ6IvJwwhCqjLlT36Ez8P69KQhE0V8MtLnrBg
# FsXZuzmaxt/ZDMhTsiHNl6f7N1oD7Y2TPJrdq7V2aihpDA+zx0RlvBPpzD98ZgeS
# PtdkqjL63B5S3RL4fjJUSb/gbL4oChQ5TZDb2Dfw7Q5qPMZ1cgeJLBwdzHZEZrzF
# RTtn4fObYUqtRF3M0Ha4xXc8odSzJTV2fvpSVXcljG1E4AMcD6CMK0E472XbhkMS
# txZHW+C/IDVJ4OoSncrH8ybi1JasEqJZ0YaPfb+aTsPV058b65l+0jQJtlxLoTIf
# p5LluL3exwr0sS3Aq5tcV3pNITtCv1FkcUk7So8sohO2OLQtC9QA300CSXna8XhQ
# OxgRA1c3HXw23MTJKSWjseDIt1bajvBu+cr/pmDxlYnWWsSCcEFaAoQohwhOMA6Z
# JfJF0tSv+koUsw6hSl7146aylSvDYUKPilAGgAUAy1yscgglMvtmQqWkEta/XGP2
# U8qvX8nUwOM=
# =DJf9
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 21 Oct 2024 17:07:04 BST
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2024-10-21' of https://gitlab.com/thuth/qemu:
tests/functional: Convert the Avocado sh4 tuxrun test
Revert "hw/sh4/r2d: Realize IDE controller before accessing it"
tests/functional: Convert the Avocado ppc32 tuxrun test
tests/functional: Convert the Avocado mips64el tuxrun test
tests/functional: Convert the Avocado mips64 tuxrun test
tests/functional: Convert the Avocado mipsel tuxrun test
tests/functional: Convert the Avocado mips tuxrun test
tests/functional: Convert the Avocado x86_64 tuxrun test
tests/functional: Convert the Avocado i386 tuxrun test
tests/functional: Convert the Avocado riscv64 tuxrun tests
tests/functional: Convert the Avocado riscv32 tuxrun tests
tests/functional: Convert the Avocado arm tuxrun tests
tests/functional: Convert the Avocado s390x tuxrun test
tests/functional: Convert the Avocado sparc64 tuxrun test
tests/functional: Convert the Avocado ppc64 tuxrun tests
tests/functional: Add a base class for the TuxRun tests
hw/pci-bridge: Add a Kconfig switch for the normal PCI bridge
MAINTAINERS: A new maintainer for the qtests
tests/qtest: Raise the ide-test timeout
tests/vm: update openbsd image to 7.6
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
https://gitlab.com/edgar.iglesias/qemu into staging
Edgars Xen queue.
# -----BEGIN PGP SIGNATURE-----
#
# iQEzBAABCgAdFiEErET+3BT38evtv0FRKcWWeA9ryoMFAmcV7NYACgkQKcWWeA9r
# yoM0pAgA2RNMysVe9IhoAlZ6ThGRvAE9epuHtoPERSTfqtFPOOY3UOU7zxrsX9Ov
# YPh41I5YtbV3fB3X8kp51pqcTOWZBBdyCLtj0EFB0XTArPvpOFPueL1q2LgEnlLV
# 77mBHnMarb3SI4INRm/tWWpk7ljgXMA6TSd2JlmO5l1OcZGlURdhLFWBBIRnTg1n
# K+ZqQyq2KMANhIYvN0JAvM45FkwXntUzbxVMIjo0ICk2/EDgcFnGn9V0TgMkcIs3
# ctBEk6reZrdvNghX02r1wsH0HKGn78358G5uZAo9YEQOoTeGDswujHOVsn73ia2a
# 6DChqCfyvlrJt4ljip2WoaoCMlZGdA==
# =QB2W
# -----END PGP SIGNATURE-----
# gpg: Signature made Mon 21 Oct 2024 06:55:34 BST
# gpg: using RSA key AC44FEDC14F7F1EBEDBF415129C596780F6BCA83
# gpg: Good signature from "Edgar E. Iglesias (Xilinx key) <edgar.iglesias@xilinx.com>" [unknown]
# gpg: aka "Edgar E. Iglesias <edgar.iglesias@gmail.com>" [full]
# Primary key fingerprint: AC44 FEDC 14F7 F1EB EDBF 4151 29C5 9678 0F6B CA83
* tag 'edgar/xen-queue-2024-10-21.for-upstream' of https://gitlab.com/edgar.iglesias/qemu:
hw/xen: Avoid use of uninitialized bufioreq_evtchn
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
This reverts commit 3c5f86a22686ef475a8259c0d8ee714f61c770c9.
Changing the order here caused a regression with the "tuxrun"
kernels (from https://storage.tuxboot.com/20230331/) - ATA commands
fail with a "ata1: lost interrupt (Status 0x58)" message.
Apparently we need to wire the interrupt here first before
realizing the device, so revert the change to the original
behavior.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-ID: <20241011131937.377223-17-thuth@redhat.com>
|
|
The pci-bridge device is not usable on s390x, so introduce a Kconfig
switch that allows to disable it.
Message-ID: <20240913144844.427899-1-thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Cédric Le Goater <clg@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
|
|
Avoid use of uninitialized bufioreq_evtchn. It should only
be used if buffered IOREQs are enabled.
Resolves: Coverity CID 1563383
Reported-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
|
|
The error message doesn't matter much, as the "openpic" device isn't
user-creatable. But it's the last use of
QERR_PROPERTY_VALUE_OUT_OF_RANGE, which has to go. Change the message
just like the previous commit did for x86 CPUs.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20241010150144.986655-7-armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
|
|
Parameter @id is no longer used, drop. Return a bool to indicate
success / failure, as recommended by qapi/error.h.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-ID: <20241010150144.986655-4-armbru@redhat.com>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
|
|
staging
pull-loongarch-20241016
# -----BEGIN PGP SIGNATURE-----
#
# iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZw91kQAKCRBAov/yOSY+
# 3+RyA/9vpqCesEBch5mzrazO4MT2IxeN2bstF8mY+EyfEwK7Ocg+esRBsigWw56k
# y6RDyCzHg200GL9TC8bJ/nMiMJjXrahhHRPVs8AADazMzX/Ys7E7ntvUUnqqANh6
# ZX8fzNJMKW6qeUVrCIwCC7E+KjfNu32dcxbXCF4mZsehIumpUQ==
# =uk+a
# -----END PGP SIGNATURE-----
# gpg: Signature made Wed 16 Oct 2024 09:13:05 BST
# gpg: using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C 6C2C 40A2 FFF2 3926 3EDF
* tag 'pull-loongarch-20241016' of https://gitlab.com/gaosong/qemu:
hw/loongarch/fw_cfg: Build in common_ss[]
hw/loongarch/virt: Remove unnecessary 'cpu.h' inclusion
target/loongarch: Avoid bits shift exceeding width of bool type
hw/loongarch/virt: Add FDT table support with acpi ged pm register
acpi: ged: Add macro for acpi sleep control register
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
staging
Remove some target-specific endianness knowledge from target/.
For MIPS, propagate endianness at the board level, using QOM property.
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEE+qvnXhKRciHc/Wuy4+MsLN6twN4FAmcOihcACgkQ4+MsLN6t
# wN4VaRAAor+5gUJiV0OOMQVfP8e1o9ssKcYy9m31zLeii1Iq2M/2oz6YK4OjdQDe
# oJ8VRJvBPKC2Bpi14TfKsSGaP8CGNO/hdxcMi71pjHZC+bjHt5Uv0U/7T4XCBWuV
# N+85juN1PTc4cci4FkGIXaPB1YWL00L56BDCzja0uhLF4+Xe2eYGVrPXeFCkN/3I
# Ky7jHlB/dgzc47kTXvg5snCee2egDFf/x4igwZj6+gWJyo+jubRpwoOqKbK2M0Nd
# VvNpBVFNGZMP3Fn9lh45uDOuRWGu6zSIPBVkjoFc+wdGsFsITIMrZ3h46UffsGTJ
# F1j6Zsq6hoLbaNRRjZ6OsN6u683oo1lknmWauD62LrjXcX0RlRwRFbMD0AjedR8t
# 6+YHg5LlwGg6r/AOtEe28ggXZohB2vjr2V0MJm1x/XgLYhFHoN3//jxn22oOHj4p
# 0z3+eDc3Se8JNRV6jPMHbbuTqZqZjRgVFbYN3aMbdoXYzhpYnrPj6f7WQL2smiAW
# C2vdswrubQWKou1wcn6rbg0nnMRVTh+GxrtZ3mkgaxNzgNFxsrX8YubMsh77XUcr
# mnCGj1tE3hp40xsuSk6yZXY3ZZiTyZasvO1wq4gWOI9le0Zmq+d335F9+IVJ8RlP
# YhA+MY5aeomsixVRdmrPrgOfanQiHXv02lsbperU8QFfGRhf2Y8=
# =Qydb
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 15 Oct 2024 16:28:23 BST
# gpg: using RSA key FAABE75E12917221DCFD6BB2E3E32C2CDEADC0DE
# gpg: Good signature from "Philippe Mathieu-Daudé (F4BUG) <f4bug@amsat.org>" [full]
# Primary key fingerprint: FAAB E75E 1291 7221 DCFD 6BB2 E3E3 2C2C DEAD C0DE
* tag 'single-binary-20241015' of https://github.com/philmd/qemu: (33 commits)
hw/mips: Have mips_cpu_create_with_clock() take an endianness argument
hw/mips/cps: Set the vCPU 'cpu-big-endian' property
target/mips: Expose MIPSCPU::is_big_endian property
target/mips: Use tcg_constant_tl() instead of tcg_gen_movi_tl()
target/mips: Use gen_op_addr_addi() when possible
target/mips: Have gen_addiupc() expand $pc during translation
target/mips: Replace MO_TE by mo_endian()
target/mips: Introduce mo_endian() helper
target/mips: Remove unused MEMOP_IDX() macro
target/mips: Rename unused sysemu argument of OP_LD_ATOMIC()
target/mips: Explode MO_TExx -> MO_TE | MO_xx
target/mips: Factor mo_endian_rev() out of MXU code
target/mips: Convert mips16e decr_and_load/store() macros to functions
target/mips: Replace MO_TE by mo_endian_env() in get_pte()
target/mips: Introduce mo_endian_env() helper
target/mips: Rename cpu_is_bigendian() -> disas_is_bigendian()
target/mips: Declare mips_env_is_bigendian() in 'internal.h'
hw/xtensa/xtfpga: Remove TARGET_BIG_ENDIAN #ifdef'ry
target/ppc: Use tcg_constant_tl() instead of tcg_gen_movi_tl()
target/tricore: Use tcg_constant_tl() instead of tcg_gen_movi_tl()
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Nothing in LoongArch fw_cfg.c requires target specific definitions.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240927213254.17552-3-philmd@linaro.org>
Signed-off-by: Song Gao <gaosong@loongson.cn>
|
|
ACPI ged is used for power management on LoongArch virt platform, in
general it is parsed from acpi table. However if system boot directly from
elf kernel, no UEFI bios is provided and acpi table cannot be used also.
Here acpi ged pm register is exposed with FDT table, it is compatbile
with syscon method in FDT table, only that acpi ged pm register is accessed
with 8-bit mode, rather with 32-bit mode.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Tested-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240918014206.2165821-3-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
|
|
Macro definition is added for acpi sleep control register, ged emulation
driver can use the macro , also it can be used in FDT table if ged is
exposed with FDT table.
Signed-off-by: Bibo Mao <maobibo@loongson.cn>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Message-Id: <20240918014206.2165821-2-maobibo@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
|
|
mips_cpu_create_with_clock() creates a vCPU. Pass it the vCPU
endianness requested by argument. Update the board call sites.
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Tested-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20241010215015.44326-17-philmd@linaro.org>
|
