| Age | Commit message (Collapse) | Author |
|---|
|
The RTC emulation does not set the IRQ flags independent of the IRQ enable bits.
The original MC146818A datasheet from 1984 notes:
"flag bits in Register C [...] are set independent of the
state of the corresponding enable bits in Register B"
Similar sections can be found in newer documentation e.g. in rtc82885.
Qemu and Bochs set the IRQ flags only if they are enabled,
which breaks drivers polling on them.
The following patch corrects this for the update-ended-flag in Qemu only.
It does not fix the handling of the other flags.
Signed-off-by: Bernhard Kauer <kauer@tudos.org>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
The logic of Zilog makes channel B the first device and channel A the
second one.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
|
|
Backport from master:
Recent versions of the Linux kernel will not preempt CPU-intensive
tasks unless the clock used by sched_clock() works. On -M versatilepb
that's the 24MHz timer in the system controller. It's a very simple
timer, so implement it.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
|
|
Hi all,
currently the vga screen_dump code doesn't use the DisplayState
interface properly and tries to replace it temporarily while taking the
screenshot.
A better approach is to register a DisplayChangeListener, call
vga_hw_update, and finally write the ppm in the next call from dpy_update.
Testing is appreciated.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Hello,
for what I can tell, there is no way for vmware_vga to work correctly
right now. It assumes that the framebuffer bits-per-pixel and the one
from the DisplaySurface are identical (it uses directly the VRAM from
vga.c), but it always assumes 3 bytes per pixel, which is never possible
with the current version of DisplaySurface.
Attached patch fixes that by using ds_get_bits_per_pixel.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
commit 93c8cfd9e67a62711b86f4c93747566885eb7928
Author: Gleb Natapov <gleb@redhat.com>
Date: Sun Aug 2 11:36:47 2009 +0300
make windows notice media change
Broke save/restore by loading a new field but not saving it.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Windows seems to be very stupid about cdrom media change. It polls
cdrom status and if status goes ready->media not present->ready
it assumes that media was changed. If "media not present" step doesn't
happen even if "medium may have changed" was seen it assumes media
haven't changed. Fake "media not present" step.
Filip Navara did a great job debugging this issue in Windows and this is
what he found out:
BINGO! ... The media present notifications were broken ever since
Windows 2000 it seems. The media change is detected properly and it's
passed to ClassSetMediaChangeState function which in turn calls
ClasspInternalSetMediaChangeState. This function is responsible for
changing some internal state of the device object and sending the PnP
events which later result in application notifications. It has this
tiny bit of code (not copied byte for byte):
if (oldMediaState == NewState) {
// Media is in the same state it was before.
return;
}
so the end result is that for the case of UNIT NEEDS ATTENTION /
MEDIUM MAY HAVE CHANGED without NOT READY in-between is really broken.
It results in the internal media change counter incremented, so the
media contents are re-read when necessary, instead of relying on the
cache, but the notifications to applications are never sent.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Message-Id:
|
|
- One type 4 table is required per cpu. Add a check for this.
- Fix check for smbios file.
Changes from v1:
- static designation of smbios_validate_table, and remove whitespace
Signed-off-by: Beth Kon <eak@us.ibm.com>
--
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Message-Id:
|
|
Hi all,
currently vga always resizes the screen when vga_hw_invalidate is called
while this is not required and all the other graphic emulators don't.
This patch fixes it, making vga invalidate behaviour consistent with the
other emulated devices.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Message-Id:
|
|
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Read of interrupt register should clear it and also sequence step and status.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Once again, the emulation of the EERD and ICS registers in e1000.c is
incorrect. Nobody has noticed this before because none of the Intel-written
e1000 drivers use these registers, and all of the independently written open
source drivers copy Intel's example, so they don't use them either.
Regardless, these registers are documented in the programmer's manuals, and
their emulated behavior doesn't match the verified behavior of real hardware,
so any software that does use them doesn't function correctly.
-Bill
Signed-off-by: Bill Paul <wpaul@windriver.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
When a VM state change handler changes VM state, other VM state change
handlers can see the state transitions out of order.
bmdma_map(), scsi_disk_init() and virtio_blk_init() install VM state
change handlers to restart DMA. These handlers can vm_stop() by
running into a write error on a drive with werror=stop. This throws
the VM state change handler callback into disarray. Here's an example
case I observed:
0. The virtual IDE drive goes south. All future writes return errors.
1. Something encounters a write error, and duly stops the VM with
vm_stop().
2. vm_stop() calls vm_state_notify(0).
3. vm_state_notify() runs the callbacks in list vm_change_state_head.
It contains ide_dma_restart_cb() installed by bmdma_map(). It also
contains audio_vm_change_state_handler() installed by audio_init().
4. audio_vm_change_state_handler() stops audio stuff.
5. User continues VM with monitor command "c". This runs vm_start().
6. vm_start() calls vm_state_notify(1).
7. vm_state_notify() runs the callbacks in vm_change_state_head.
8. ide_dma_restart_cb() happens to come first. It does its work, runs
into a write error, and duly stops the VM with vm_stop().
9. vm_stop() runs vm_state_notify(0).
10. vm_state_notify() runs the callbacks in vm_change_state_head.
11. audio_vm_change_state_handler() stops audio stuff. Which isn't
running.
12. vm_stop() finishes, ide_dma_restart_cb() finishes, step 7's
vm_state_notify() resumes running handlers.
13. audio_vm_change_state_handler() starts audio stuff. Oopsie.
Fix this by moving the actual write from each VM state change handler
into a new bottom half (suggested by Gleb Natapov).
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
These are now unused.
However, perhaps the idea is that when we add -device, they will be
useful? In that case, we should add virtio-net-pci-0-10 too.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
We have the pc-0.10 machine type now which does exactly the same
thing.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
The pc-0.11 type allows users of qemu-0.11 to use a machine type which
they know will remain compatible when the upgrade to qemu-0.12.
Management tools may choose to canonicalize the 'pc' machine type to
'pc-0.11' so that if the 'pc' alias changes target in future versions
of qemu, the machine type used will remain compatible.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Add an 'alias' field to QEMUMachine and display it in the output of
'qemu -M ?' with an '(aliased to foo)' suffix.
Aliases can change targets in newer versions of qemu, so management tools
may choose canonicalize machine types to ensure that if a user chooses an
alias, that the actual machine type used will remain compatible in
future.
This is intended to mimic a symlink to a machine description file.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
I don't think it's critical to do this, but it's
best to keep uninit and error recovery consistent.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
This patch addresses the problems found by Andriy Gapon:
- The code was incorrectly overwriting the high order 32
bits of the timer and hpet config registers. This didn't show up
in testing because linux and windows use hpet in legacy mode,
where the high order 32 bits (advertising available interrupts)
of the timer config register are ignored, and the high order 32
bits of the hpet config register are reserved and unused.
- The mask for level-triggered interrupts was off by a bit. (hpet
doesn't currently support level-triggered interrupts).
In addition, I removed some unused #defines, and corrected the ioapic
interrupt values advertised. I'd set this up early in hpet development
and never went back to correct it, and no bugs resulted since linux and
windows use hpet in legacy mode where available interrupts are ignored.
Signed-off-by: Beth Kon <eak@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
This patch requires "Handle BH's queued by AIO completions in
qemu_aio_flush()" to work reliably. The combination of those two
patches survived 300+ migrations with heavy IO load running in the
guest.
Signed-off-by: Nolan Leake <nolan <at> sigbus.net>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
I used the following command to enable debugging:
perl -p -i -e 's/^\/\/#define DEBUG/#define DEBUG/g' * */* */*/*
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
Hi!
Attached patch uses qemu_isxdigit() instead of isxdigit().
Fixes build warning on NetBSD.
Signed-off-by: Christoph Egger <Christoph.Egger@amd.com>
--
---to satisfy European Law for business letters:
Advanced Micro Devices GmbH
Karl-Hammerschmidt-Str. 34, 85609 Dornach b. Muenchen
Geschaeftsfuehrer: Thomas M. McCoy, Giuliano Meroni
Sitz: Dornach, Gemeinde Aschheim, Landkreis Muenchen
Registergericht Muenchen, HRB Nr. 43632
|
|
Move the export to a file used by both qdev.c and sysbus.c.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
0x10000000 looks better than 268435456.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
The logic of Zilog makes channel B the first device and channel A the
second one.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
On some Sparc32 machines, fdc is located above 4G limit, so uint32_t is not
appropriate type for io_base.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
Move the qdev_init(dev); call after the setting of d->size.
Thanks to Filip Navara.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
The sequence of reading from eeprom is "offset by one" moved because of a false
detection of a clock cycle after an eeprom reset. Keeping the last clock value
after a reset keeps it in sync.
Signed-off-by: Naphtali Sprei <nsprei@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Add vectors property, allowing to turn off msi by setting vectors=0.
Add compat property to pc-0.10 disabling msi.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Add class property to virtio-console-pci allowing to specify the PCI class.
Add compat property to pc-0.10 to set the old PCI class.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Add class property to virtio-blk-pci allowing to specify the PCI class.
Add compat property to pc-0.10 to set the old PCI class.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Add id field to DeviceState. Make "info qtree" print it.
This helps users and management apps identifying devices in monitor
output, which is especially useful with otherwise identical devices
such as two virtio disks.
This patch doesn't add a way to set the id, followup patches will do.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
no_user: prevent users from adding certain devices.
desc: description of the device.
alias: to allow user friendly shortcuts on the command line, i.e.
-device usbmouse instead of -device "QEMU USB Mouse" or
-device lsi instead of -device lsi53c895a
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
This add support for switching devices into a compatibility mode
using device properties. Machine types can have a list of properties
for specific devices attached to allow the easy creation of machine
types compatible to older qemu versions.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
This patch is a major overhaul of the device properties. The properties
are saved directly in the device state struct now, the linked list of
property values is gone.
Advantages:
* We don't have to maintain the list with the property values.
* The value in the property list and the value actually used by
the device can't go out of sync any more (used to happen for
the pci.devfn == -1 case) because there is only one place where
the value is stored.
* A record describing the property is required now, you can't set
random properties any more.
There are bus-specific and device-specific properties. The former
should be used for properties common to all bus drivers. Typical
use case is bus addressing, i.e. pci.devfn and i2c.address.
Properties have a PropertyInfo struct attached with name, size and
function pointers to parse and print properties. A few common property
types have PropertyInfos defined in qdev-properties.c. Drivers are free
to implement their own very special property parsers if needed.
Properties can have default values. If unset they are zero-filled.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Currently only common PS2 state is initialized, leaving keyboard and
mouse specific state to contain stale values.
Signed-off-by: Dinesh Subhraveti <dineshs@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Without this, after system reset, hpet does not detect transition from
non-legacy to legacy mode.
Signed-off-by: Beth Kon <eak@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Here is a patch I had sent twice to the list 2 years ago.
Hopefuly this time someone will be interested
It adds support for passing vga mode to linux kernel through
vga= option in -append
Signed-off-by: Pascal Terjan <pterjan@gmail.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
Also increase QDEV_MAX_IRQ.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
