| Age | Commit message (Collapse) | Author |
|---|
|
Use device_class_set_parent_realize() to set parent realize() directly.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
Use device_class_set_parent_realize() to set parent realize() directly.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
Use device_class_set_parent_realize() to set parent realize() directly.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
Use device_class_set_parent_realize() to set parent realize() directly.
Signed-off-by: Zhao Liu <zhao1.liu@intel.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
Load the 64-bit SeaBIOS-hppa firmware by default when running on a 64-bit
machine. This will enable us to later support more than 4GB of RAM and is
required that the OS (or PALO bootloader) will start or install a 64-bit kernel
instead of a 32-bit kernel.
Note that SeaBIOS-hppa v16 provides the "-fw_cfg opt/OS64,string=3" option with
which the user can control what the firmware shall report back to the OS:
Support of 32-bit OS, support of a 64-bit OS, or support for both (default).
Wrap firmware loading inside !qtest_enabled() to avoid this warning with
qtest: "qemu-system-hppa: no firmware provided".
Signed-off-by: Helge Deller <deller@gmx.de>
Acked-by: Richard Henderson <richard.henderson@linaro.org>
|
|
Netbsd isn't able to detect a link on the emulated tulip card. That's
because netbsd reads the Chip Status Register of the Phy (address
0x14). The default phy data in the qemu tulip driver is all zero,
which means no link is established and autonegotation isn't complete.
Therefore set the register to 0x3b40, which means:
Link is up, Autonegotation complete, Full Duplex, 100MBit/s Link
speed.
Also clear the mask because this register is read only.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Helge Deller <deller@gmx.de>
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Linux writes zeroes at bootup into the default ports for LASI audio and
LASI floppy controller to reset those devices. Allow writing to those
registers to avoid HPMCs.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Firmware and qemu reads and writes the MAC address for the LASI LAN via
registers in LASI. Allow those accesses and return zero even if LASI
LAN isn't enabled to avoid HPMCs (=crashes).
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
The Astro/Elroy chip can work in either Hard-Fail or Soft-Fail mode.
Hard fail means the system bus will send an HPMC (=crash) to the
processor, soft fail means the system bus will ignore timeouts of
MMIO-reads or MMIO-writes and return -1ULL.
The HF mode is controlled by a bit in the status register and is usually
programmed by the OS. Return the corresponing values based on the current
value of that bit.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
|
|
Instead of stopping the emulation, report a MEMTX_DECODE_ERROR if the OS
tries to access non-existent registers.
Signed-off-by: Helge Deller <deller@gmx.de>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
|
|
https://github.com/alistair23/qemu into staging
RISC-V PR for 9.0
* Check for 'A' extension on all atomic instructions
* Add support for 'B' extension
* Internally deprecate riscv_cpu_options
* Implement optional CSR mcontext of debug Sdtrig extension
* Internally add cpu->cfg.vlenb and remove cpu->cfg.vlen
* Support vlenb and vregs[] in KVM
* RISC-V gdbstub and TCG plugin improvements
* Remove vxrm and vxsat from FCSR
* Use RISCVException as return type for all csr ops
* Use g_autofree more and fix a memory leak
* Add support for Zaamo and Zalrsc
* Support new isa extension detection devicetree properties
* SMBIOS support for RISC-V virt machine
* Enable xtheadsync under user mode
* Add rv32i,rv32e and rv64e CPUs
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEaukCtqfKh31tZZKWr3yVEwxTgBMFAmXGBRAACgkQr3yVEwxT
# gBPqVA//etMiwP8+lQb2E4pw+QwBIzpm3qFyBlqgSCFrekj1u2kYNd4CH3CKurWE
# ysoQ6OAMeb0MUbRHdjrejjzD/wOg7JNA9h7ynM1VbupveBrJY3GWC6qQWSG+A1j/
# LSgmr/dDya74chDxjxa+7ld3xqloHi5OtdGaeORfdPXl7mjCCKKCoSKYCex1ykup
# uuB7bsjeWeWEbuUsntmeuHJLZJuhpnbuZJmp17tEo+3vWXqjxV00Lik+XMwh3gua
# KOLiAqHjGr2NEhA3Mg1JLcQ+6JLTDM9ugZpQeNGQwMkfuB/RAU7jO/1Di3flbadF
# 8l2xOHu3mydDbfdxTGZNJjcIrMTX/YEewAYZLRYpNsyPOMntgq8HEegwCdWGvK7C
# M5Tc59MNSuBt+zkZkHd21qLYusa2ThP4YT/schh7IA+2F1TSKdhlptEzi2oebIc7
# ilLSgZ9Of72QlAH2OPJNSAL9Nbc06MHEM0JiHIJa5u+XdcVRhZus5h1YIOKXisqF
# YPP22RnI5Jj5d5csa/0ONAZGFh5SRMTJtpjKoKSkzoYJWDjCQ2MiUAOmLscchMZd
# wbK0vjeRf6kRG4U4z7nTmHS9kzH8RXUZDecVcOITuMpKih9LhUiCZ+xPunFYPycJ
# WNFa9/pENcCXJweXvtk4NHwx933rX56678lF6KY2hwUwwaiBOv4=
# =yuRM
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 09 Feb 2024 10:57:20 GMT
# gpg: using RSA key 6AE902B6A7CA877D6D659296AF7C95130C538013
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6AE9 02B6 A7CA 877D 6D65 9296 AF7C 9513 0C53 8013
* tag 'pull-riscv-to-apply-20240209' of https://github.com/alistair23/qemu: (61 commits)
target/riscv: add rv32i, rv32e and rv64e CPUs
target/riscv/cpu.c: add riscv_bare_cpu_init()
target/riscv: Enable xtheadsync under user mode
qemu-options: enable -smbios option on RISC-V
target/riscv: SMBIOS support for RISC-V virt machine
smbios: function to set default processor family
smbios: add processor-family option
target/riscv: support new isa extension detection devicetree properties
target/riscv: use misa_mxl_max to populate isa string rather than TARGET_LONG_BITS
target/riscv: Expose Zaamo and Zalrsc extensions
target/riscv: Check 'A' and split extensions for atomic instructions
target/riscv: Add Zaamo and Zalrsc extension infrastructure
hw/riscv/virt.c: use g_autofree in create_fdt_*
hw/riscv/virt.c: use g_autofree in virt_machine_init()
hw/riscv/virt.c: use g_autofree in create_fdt_virtio()
hw/riscv/virt.c: use g_autofree in create_fdt_sockets()
hw/riscv/virt.c: use g_autofree in create_fdt_socket_cpus()
hw/riscv/numa.c: use g_autofree in socket_fdt_write_distance_matrix()
hw/riscv/virt-acpi-build.c: fix leak in build_rhct()
target/riscv: Use RISCVException as return type for all csr ops
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Generate SMBIOS tables for the RISC-V mach-virt.
Add CONFIG_SMBIOS=y to the RISC-V default config.
Set the default processor family in the type 4 table.
The implementation is based on the corresponding ARM and Loongson code.
With the patch the following firmware tables are provided:
etc/smbios/smbios-anchor
etc/smbios/smbios-tables
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20240123184229.10415-4-heinrich.schuchardt@canonical.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
Provide a function to set the default processor family.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20240123184229.10415-3-heinrich.schuchardt@canonical.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
For RISC-V the SMBIOS standard requires specific values of the processor
family value depending on the bitness of the CPU.
Add a processor-family option for SMBIOS table 4.
The value of processor-family may exceed 255 and therefore must be provided
in the Processor Family 2 field. Set the Processor Family field to 0xFE
which signals that the Processor Family 2 is used.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Message-ID: <20240123184229.10415-2-heinrich.schuchardt@canonical.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
A few months ago I submitted a patch to various lists, deprecating
"riscv,isa" with a lengthy commit message [0] that is now commit
aeb71e42caae ("dt-bindings: riscv: deprecate riscv,isa") in the Linux
kernel tree. Primarily, the goal was to replace "riscv,isa" with a new
set of properties that allowed for strictly defining the meaning of
various extensions, where "riscv,isa" was tied to whatever definitions
inflicted upon us by the ISA manual, which have seen some variance over
time.
Two new properties were introduced: "riscv,isa-base" and
"riscv,isa-extensions". The former is a simple string to communicate the
base ISA implemented by a hart and the latter an array of strings used
to communicate the set of ISA extensions supported, per the definitions
of each substring in extensions.yaml [1]. A beneficial side effect was
also the ability to define vendor extensions in a more "official" way,
as the ISA manual and other RVI specifications only covered the format
for vendor extensions in the ISA string, but not the meaning of vendor
extensions, for obvious reasons.
Add support for setting these two new properties in the devicetrees for
the various devicetree platforms supported by QEMU for RISC-V. The Linux
kernel already supports parsing ISA extensions from these new
properties, and documenting them in the dt-binding is a requirement for
new extension detection being added to the kernel.
A side effect of the implementation is that the meaning for elements in
"riscv,isa" and in "riscv,isa-extensions" are now tied together as they
are constructed from the same source. The same applies to the ISA string
provided in ACPI tables, but there does not appear to be any strict
definitions of meanings in ACPI land either.
Link: https://lore.kernel.org/qemu-riscv/20230702-eats-scorebook-c951f170d29f@spud/ [0]
Link: https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/Documentation/devicetree/bindings/riscv/extensions.yaml [1]
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Andrew Jones <ajones@ventanamicro.com>
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Message-ID: <20240124-unvarying-foothold-9dde2aaf95d4@spud>
[ Changes by AF:
- Rebase on recent changes
]
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
We have a lot of cases where a char or an uint32_t pointer is used once
to alloc a string/array, read/written during the function, and then
g_free() at the end. There's no pointer re-use - a single alloc, a
single g_free().
Use 'g_autofree' to avoid the g_free() calls.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240122221529.86562-8-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
Move 'soc_name' to the loop, and give it g_autofree, to avoid the manual
g_free().
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240122221529.86562-7-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
Put 'name' declaration inside the loop, with g_autofree, to avoid
manually doing g_free() in each iteration.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240122221529.86562-6-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
Move 'clust_name' inside the loop, and g_autofree, to avoid having to
g_free() manually in each loop iteration.
'intc_phandles' is also g_autofreed to avoid another manual g_free().
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240122221529.86562-5-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
Move all char pointers to the loop. Use g_autofree in all of them to
avoid the g_free() calls.
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240122221529.86562-4-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
Use g_autofree in 'dist_matrix' to avoid the manual g_free().
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240122221529.86562-3-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
The 'isa' char pointer isn't being freed after use.
Issue detected by Valgrind:
==38752== 128 bytes in 1 blocks are definitely lost in loss record 3,190 of 3,884
==38752== at 0x484280F: malloc (vg_replace_malloc.c:442)
==38752== by 0x5189619: g_malloc (gmem.c:130)
==38752== by 0x51A5BF2: g_strconcat (gstrfuncs.c:628)
==38752== by 0x6C1E3E: riscv_isa_string_ext (cpu.c:2321)
==38752== by 0x6C1E3E: riscv_isa_string (cpu.c:2343)
==38752== by 0x6BD2EA: build_rhct (virt-acpi-build.c:232)
==38752== by 0x6BD2EA: virt_acpi_build (virt-acpi-build.c:556)
==38752== by 0x6BDC86: virt_acpi_setup (virt-acpi-build.c:662)
==38752== by 0x9C8DC6: notifier_list_notify (notify.c:39)
==38752== by 0x4A595A: qdev_machine_creation_done (machine.c:1589)
==38752== by 0x61E052: qemu_machine_creation_done (vl.c:2680)
==38752== by 0x61E052: qmp_x_exit_preconfig.part.0 (vl.c:2709)
==38752== by 0x6220C6: qmp_x_exit_preconfig (vl.c:2702)
==38752== by 0x6220C6: qemu_init (vl.c:3758)
==38752== by 0x425858: main (main.c:47)
Fixes: ebfd392893 ("hw/riscv/virt: virt-acpi-build.c: Add RHCT Table")
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240122221529.86562-2-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
misa_mxl_max is common for all instances of a RISC-V CPU class so they
are better put into class.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240203-riscv-v11-2-a23f4848a628@daynix.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
Block layer patches
- Allow concurrent BB context changes
- virtio: Re-enable notifications after drain
- virtio-blk: Fix missing use of irqfd
- scsi: Don't ignore most usb-storage properties
- blkio: Respect memory-alignment for bounce buffer allocations
- iotests tmpdir fixes
- virtio-blk: Code cleanups
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEE3D3rFZqa+V09dFb+fwmycsiPL9YFAmXEkwgRHGt3b2xmQHJl
# ZGhhdC5jb20ACgkQfwmycsiPL9Y3jA//TmSBVqHljauyImYOgCt8qCXACttV0xhQ
# Q5ldUNx/JmIFMoUR7OlpVAL2MtvdwE0jjY+sDlEmWtz4IFJcCsCTUCHZZb8blreb
# +mnMkqrQ6Nb3tPR2jeIknrXqNy1ffyjZItktjWXVcl6jaHB8YabHHqszs9DIaf4n
# lcKovBKxula8ckMgvm48wCwTtS7VEPeuC5FrOqUqTtuhg+QKp5ZVoyVFHtf6GKTD
# iuXzCd4yxu4fDKAthJJj4N1bQaOmCKU7K9N/665wj9P2TyfmwlBAfNwNAlYbdX1E
# Sv7eSioQs2+oUxmfD/PUsF7wTYtDCrSAUFn1kP/XdRyXPJR3dHGiBKV9w9CaWNrU
# y8rqOhxVcuoBLRljTF32BK4HniAREjRngtpT2FnQQIyedZrXIwyTAWjs+LW12T6O
# NMiU603Nl9ZYhO1et2+qspsVpNIfEpQWpK+OCon6E+ggj1ea+pfqU30VPx4JU05I
# VLiydluIbehSkRlTHgFcTgApmx843OGW7CvWfRyen86Cexgx3DEjJUQ4/bYqaCha
# yLIi91rToSDmtlzJrg9eYiMs5Y6vz+ORvvX5im1RlbUUb7Kx/LaA4BU/uArEbBt8
# xXm/grO4hFUGqtLgd2LIjWaHSsLoW4jKeEiExFUUfvH5DG9Zl5HmzFwu+DYxX+im
# MJLLetDJAWI=
# =8tc0
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 08 Feb 2024 08:38:32 GMT
# gpg: using RSA key DC3DEB159A9AF95D3D7456FE7F09B272C88F2FD6
# gpg: issuer "kwolf@redhat.com"
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* tag 'for-upstream' of https://repo.or.cz/qemu/kevin:
virtio-blk: avoid using ioeventfd state in irqfd conditional
virtio-blk: Use ioeventfd_attach in start_ioeventfd
virtio: Re-enable notifications after drain
virtio-scsi: Attach event vq notifier with no_poll
blkio: Respect memory-alignment for bounce buffer allocations
scsi: Don't ignore most usb-storage properties
virtio-blk: do not use C99 mixed declarations
iotests: give tempdir an identifying name
iotests: fix leak of tmpdir in dry-run mode
scsi: Await request purging
block-backend: Allow concurrent context changes
monitor: use aio_co_reschedule_self()
virtio-blk: declare VirtIOBlock::rq with a type
virtio-blk: add vq_rq[] bounds check in virtio_blk_dma_restart_cb()
virtio-blk: clarify that there is at least 1 virtqueue
virtio-blk: enforce iothread-vq-mapping validation
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
staging
* Emulate CVB, CVBY, CVBG and CVDG s390x instructions
* Fix bug in lsi53c895a reentrancy counter
* Deprecate the "power5+" and "power7+" CPU names
* Fix problems in the freebsd VM test
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEEJ7iIR+7gJQEY8+q5LtnXdP5wLbUFAmXCCXURHHRodXRoQHJl
# ZGhhdC5jb20ACgkQLtnXdP5wLbXtEA/9HKWMHbWqDAdlrpmfW8lCFaBHgV0+Fqsy
# GlxJykni2BxIWNoR7J6SdAqbgx3E2/7i8IMIUwYXlNBjEs/UQ0ZcnI5k6OfUS24p
# qfbdH717SgsaB9R1vCBhmOGGWYBfe/RqPGIcni/eg+jSxB5cn2XvEv3+ZBckvDsh
# KFuuAa6vvuBVhyXLbkP8Z+LEe27ttIYi5v1dvJ1an4UbFESqxVb0knyuFYpZpY8Y
# h7dZ0hyCid7YT03zVmSADK7anO+epBdzUU3SsKXj2dB9nebSjmkav6lQQBKYHHUg
# THojcWKwFPNK0AojhBuBCqFYgkGGt/9kjwlUt7jfm1TcSemN65XLNYHThRekPuAJ
# Jcze8dcEerbj1xsNWYh4hPvB92laEiyVR5BYFfUkJ9m2IAamPQLHvOT7jzhC3Y9k
# 4wvVcf9QKVtKW0QO54SQjD4A/qQu/4777oH5w83nGuxjUthmHDqZmjDlIRe6lKJt
# gsA+mKn+w9HrtiXOSkoMhK8PAyvCoAef/N7kvHZoHmp6TtfQAjPs4/v2uZMpnd60
# z7Cw50giHpo9lmiZ1Ey2fQvw9orYhNoXAc4XfYGHuYdQFWpCGz1PB2Km8uTPTEUe
# as364ULBqWoFBCRuRndy2+z2e3zhK5THTPCAyHf48M6teMEPa4KTsTCk7MzmfVfx
# C8RsLcmrFPI=
# =eQNc
# -----END PGP SIGNATURE-----
# gpg: Signature made Tue 06 Feb 2024 10:27:01 GMT
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5
* tag 'pull-request-2024-02-06' of https://gitlab.com/thuth/qemu:
meson: Link with libinotify on FreeBSD
test-util-filemonitor: Adapt to the FreeBSD inotify rename semantics
tests/vm/freebsd: Reload the sshd configuration
tests/vm: Set UseDNS=no in the sshd configuration
target/s390x: Prefer fast cpu_env() over slower CPU QOM cast macro
tests/tcg/s390x: Test CONVERT TO BINARY
tests/tcg/s390x: Test CONVERT TO DECIMAL
target/s390x: Emulate CVB, CVBY and CVBG
target/s390x: Emulate CVDG
docs/about: Deprecate the old "power5+" and "power7+" CPU names
target/ppc/cpu-models: Rename power5+ and power7+ for new QOM naming rules
hw/scsi/lsi53c895a: add missing decrement of reentrancy counter
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Requests that complete in an IOThread use irqfd to notify the guest
while requests that complete in the main loop thread use the traditional
qdev irq code path. The reason for this conditional is that the irq code
path requires the BQL:
if (s->ioeventfd_started && !s->ioeventfd_disabled) {
virtio_notify_irqfd(vdev, req->vq);
} else {
virtio_notify(vdev, req->vq);
}
There is a corner case where the conditional invokes the irq code path
instead of the irqfd code path:
static void virtio_blk_stop_ioeventfd(VirtIODevice *vdev)
{
...
/*
* Set ->ioeventfd_started to false before draining so that host notifiers
* are not detached/attached anymore.
*/
s->ioeventfd_started = false;
/* Wait for virtio_blk_dma_restart_bh() and in flight I/O to complete */
blk_drain(s->conf.conf.blk);
During blk_drain() the conditional produces the wrong result because
ioeventfd_started is false.
Use qemu_in_iothread() instead of checking the ioeventfd state.
Cc: qemu-stable@nongnu.org
Buglink: https://issues.redhat.com/browse/RHEL-15394
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240122172625.415386-1-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
Commit d3f6f294aeadd5f88caf0155e4360808c95b3146 ("virtio-blk: always set
ioeventfd during startup") has made virtio_blk_start_ioeventfd() always
kick the virtqueue (set the ioeventfd), regardless of whether the BB is
drained. That is no longer necessary, because attaching the host
notifier will now set the ioeventfd, too; this happens either
immediately right here in virtio_blk_start_ioeventfd(), or later when
the drain ends, in virtio_blk_ioeventfd_attach().
With event_notifier_set() removed, the code becomes the same as the one
in virtio_blk_ioeventfd_attach(), so we can reuse that function.
Signed-off-by: Hanna Czenczek <hreitz@redhat.com>
Message-ID: <20240202153158.788922-4-hreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
During drain, we do not care about virtqueue notifications, which is why
we remove the handlers on it. When removing those handlers, whether vq
notifications are enabled or not depends on whether we were in polling
mode or not; if not, they are enabled (by default); if so, they have
been disabled by the io_poll_start callback.
Because we do not care about those notifications after removing the
handlers, this is fine. However, we have to explicitly ensure they are
enabled when re-attaching the handlers, so we will resume receiving
notifications. We do this in virtio_queue_aio_attach_host_notifier*().
If such a function is called while we are in a polling section,
attaching the notifiers will then invoke the io_poll_start callback,
re-disabling notifications.
Because we will always miss virtqueue updates in the drained section, we
also need to poll the virtqueue once after attaching the notifiers.
Buglink: https://issues.redhat.com/browse/RHEL-3934
Signed-off-by: Hanna Czenczek <hreitz@redhat.com>
Message-ID: <20240202153158.788922-3-hreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
As of commit 38738f7dbbda90fbc161757b7f4be35b52205552 ("virtio-scsi:
don't waste CPU polling the event virtqueue"), we only attach an io_read
notifier for the virtio-scsi event virtqueue instead, and no polling
notifiers. During operation, the event virtqueue is typically
non-empty, but none of the buffers are intended to be used immediately.
Instead, they only get used when certain events occur. Therefore, it
makes no sense to continuously poll it when non-empty, because it is
supposed to be and stay non-empty.
We do this by using virtio_queue_aio_attach_host_notifier_no_poll()
instead of virtio_queue_aio_attach_host_notifier() for the event
virtqueue.
Commit 766aa2de0f29b657148e04599320d771c36fd126 ("virtio-scsi: implement
BlockDevOps->drained_begin()") however has virtio_scsi_drained_end() use
virtio_queue_aio_attach_host_notifier() for all virtqueues, including
the event virtqueue. This can lead to it being polled again, undoing
the benefit of commit 38738f7dbbda90fbc161757b7f4be35b52205552.
Fix it by using virtio_queue_aio_attach_host_notifier_no_poll() for the
event virtqueue.
Reported-by: Fiona Ebner <f.ebner@proxmox.com>
Fixes: 766aa2de0f29b657148e04599320d771c36fd126
("virtio-scsi: implement BlockDevOps->drained_begin()")
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Reviewed-by: Fiona Ebner <f.ebner@proxmox.com>
Signed-off-by: Hanna Czenczek <hreitz@redhat.com>
Message-ID: <20240202153158.788922-2-hreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
usb-storage is for the most part just a wrapper around an internally
created scsi-disk device. It uses DEFINE_BLOCK_PROPERTIES() to offer all
of the usual block device properties to the user, but then only forwards
a few select properties to the internal device while the rest is
silently ignored.
This changes scsi_bus_legacy_add_drive() to accept a whole BlockConf
instead of some individual values inside of it so that usb-storage can
now pass the whole configuration to the internal scsi-disk. This enables
the remaining block device properties, e.g. logical/physical_block_size
or discard_granularity.
Buglink: https://issues.redhat.com/browse/RHEL-22375
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20240131130607.24117-1-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
QEMU's coding style generally forbids C99 mixed declarations.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240206140410.65650-1-stefanha@redhat.com>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
scsi_device_for_each_req_async() currently does not provide any way to
be awaited. One of its callers is scsi_device_purge_requests(), which
therefore currently does not guarantee that all requests are fully
settled when it returns.
We want all requests to be settled, because scsi_device_purge_requests()
is called through the unrealize path, including the one invoked by
virtio_scsi_hotunplug() through qdev_simple_device_unplug_cb(), which
most likely assumes that all SCSI requests are done then.
In fact, scsi_device_purge_requests() already contains a blk_drain(),
but this will not fully await scsi_device_for_each_req_async(), only the
I/O requests it potentially cancels (not the non-I/O requests).
However, we can have scsi_device_for_each_req_async() increment the BB
in-flight counter, and have scsi_device_for_each_req_async_bh()
decrement it when it is done. This way, the blk_drain() will fully
await all SCSI requests to be purged.
This also removes the need for scsi_device_for_each_req_async_bh() to
double-check the current context and potentially re-schedule itself,
should it now differ from the BB's context: Changing a BB's AioContext
with a root node is done through bdrv_try_change_aio_context(), which
creates a drained section. With this patch, we keep the BB in-flight
counter elevated throughout, so we know the BB's context cannot change.
Signed-off-by: Hanna Czenczek <hreitz@redhat.com>
Message-ID: <20240202144755.671354-3-hreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
Hanna Czenczek <hreitz@redhat.com> noted that the array index in
virtio_blk_dma_restart_cb() is not bounds-checked:
g_autofree VirtIOBlockReq **vq_rq = g_new0(VirtIOBlockReq *, num_queues);
...
while (rq) {
VirtIOBlockReq *next = rq->next;
uint16_t idx = virtio_get_queue_index(rq->vq);
rq->next = vq_rq[idx];
^^^^^^^^^^
The code is correct because both rq->vq and vq_rq[] depend on
num_queues, but this is indirect and not 100% obvious. Add an assertion.
Suggested-by: Hanna Czenczek <hreitz@redhat.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240206190610.107963-4-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
It is not possible to instantiate a virtio-blk device with 0 virtqueues.
The following check is located in ->realize():
if (!conf->num_queues) {
error_setg(errp, "num-queues property must be larger than 0");
return;
}
Later on we access s->vq_aio_context[0] under the assumption that there
is as least one virtqueue. Hanna Czenczek <hreitz@redhat.com> noted that
it would help to show that the array index is already valid.
Add an assertion to document that s->vq_aio_context[0] is always
safe...and catch future code changes that break this assumption.
Suggested-by: Hanna Czenczek <hreitz@redhat.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20240206190610.107963-3-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
Hanna Czenczek <hreitz@redhat.com> noticed that the safety of
`vq_aio_context[vq->value] = ctx;` with user-defined vq->value inputs is
not obvious.
The code is structured in validate() + apply() steps so input validation
is there, but it happens way earlier and there is nothing that
guarantees apply() can only be called with validated inputs.
This patch moves the validate() call inside the apply() function so
validation is guaranteed. I also added the bounds checking assertion
that Hanna suggested.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Hanna Czenczek <hreitz@redhat.com>
Message-ID: <20240206190610.107963-2-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
QEMU initializes preallocated backend memory as the objects are parsed from
the command line. This is not optimal in some cases (e.g. memory spanning
multiple NUMA nodes) because the memory objects are initialized in series.
Allow the initialization to occur in parallel (asynchronously). In order to
ensure optimal thread placement, asynchronous initialization requires prealloc
context threads to be in use.
Signed-off-by: Mark Kanda <mark.kanda@oracle.com>
Message-ID: <20240131165327.3154970-2-mark.kanda@oracle.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
|
|
We used to check that the memory region size is multiples of the overall
requested address alignment for the device memory address.
We removed that check, because there are cases (i.e., hv-balloon) where
devices unconditionally request an address alignment that has a very large
alignment (i.e., 32 GiB), but the actual memory device size might not be
multiples of that alignment.
However, this change:
(a) allows for some practically impossible DIMM sizes, like "1GB+1 byte".
(b) allows for DIMMs that partially cover hugetlb pages, previously
reported in [1].
Both scenarios don't make any sense: we might even waste memory.
So let's reintroduce that check, but only check that the
memory region size is multiples of the memory region alignment (i.e.,
page size, huge page size), but not any additional memory device
requirements communicated using md->get_min_alignment().
The following examples now fail again as expected:
(a) 1M with 2M THP
qemu-system-x86_64 -m 4g,maxmem=16g,slots=1 -S -nodefaults -nographic \
-object memory-backend-ram,id=mem1,size=1M \
-device pc-dimm,id=dimm1,memdev=mem1
-> backend memory size must be multiple of 0x200000
(b) 1G+1byte
qemu-system-x86_64 -m 4g,maxmem=16g,slots=1 -S -nodefaults -nographic \
-object memory-backend-ram,id=mem1,size=1073741825B \
-device pc-dimm,id=dimm1,memdev=mem1
-> backend memory size must be multiple of 0x200000
(c) Unliagned hugetlb size (2M)
qemu-system-x86_64 -m 4g,maxmem=16g,slots=1 -S -nodefaults -nographic \
-object memory-backend-file,id=mem1,mem-path=/dev/hugepages/tmp,size=511M \
-device pc-dimm,id=dimm1,memdev=mem1
backend memory size must be multiple of 0x200000
(d) Unliagned hugetlb size (1G)
qemu-system-x86_64 -m 4g,maxmem=16g,slots=1 -S -nodefaults -nographic \
-object memory-backend-file,id=mem1,mem-path=/dev/hugepages1G/tmp,size=2047M \
-device pc-dimm,id=dimm1,memdev=mem1
-> backend memory size must be multiple of 0x40000000
Note that this fix depends on a hv-balloon change to communicate its
additional alignment requirements using get_min_alignment() instead of
through the memory region.
[1] https://lkml.kernel.org/r/f77d641d500324525ac036fe1827b3070de75fc1.1701088320.git.mprivozn@redhat.com
Message-ID: <20240117135554.787344-3-david@redhat.com>
Reported-by: Zhenyu Zhang <zhenyzha@redhat.com>
Reported-by: Michal Privoznik <mprivozn@redhat.com>
Fixes: eb1b7c4bd413 ("memory-device: Drop size alignment check")
Tested-by: Zhenyu Zhang <zhenyzha@redhat.com>
Tested-by: Mario Casquero <mcasquer@redhat.com>
Reviewed-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
|
|
The character "+" is now forbidden in QOM device names (see commit
b447378e1217 - "Limit type names to alphanumerical and some few special
characters"). For the "power5+" and "power7+" CPU names, there is
currently a hack in type_name_is_valid() to still allow them for
compatibility reasons. However, there is a much nicer solution for this:
Simply use aliases! This way we can still support the old names without
the need for the ugly hack in type_name_is_valid().
Message-ID: <20240117141054.73841-2-thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
|
|
When the maximum count of SCRIPTS instructions is reached, the code
stops execution and returns, but fails to decrement the reentrancy
counter. This effectively renders the SCSI controller unusable
because on next entry the reentrancy counter is still above the limit.
This bug was seen on HP-UX 10.20 which seems to trigger SCRIPTS
loops.
Fixes: b987718bbb ("hw/scsi/lsi53c895a: Fix reentrancy issues in the LSI controller (CVE-2023-0330)")
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-ID: <20240128202214.2644768-1-svens@stackframe.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Thomas Huth <thuth@redhat.com>
|
|
Let's implement the get_min_alignment() callback for memory devices, and
copy for the device memory region the alignment of the host memory
region. This mimics what virtio-mem does, and allows for re-introducing
proper alignment checks for the memory region size (where we don't care
about additional device requirements) in memory device core.
Message-ID: <20240117135554.787344-2-david@redhat.com>
Reviewed-by: Maciej S. Szmigiero <maciej.szmigiero@oracle.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
|
|
https://git.linaro.org/people/pmaydell/qemu-arm into staging
target/arm: fix exception syndrome for AArch32 bkpt insn
pci, vmbus, adb, s390x/css-bridge: Switch buses to 3-phase reset
system/vl.c: Fix handling of '-serial none -serial something'
target/arm: Add ID_AA64ZFR0_EL1.B16B16 to the exposed-to-userspace set
tests/qtest/xlnx-versal-trng-test.c: Drop use of variable length array
target/arm: Reinstate "vfp" property on AArch32 CPUs
doc/sphinx/hxtool.py: add optional label argument to SRST directive
hw/arm: Check for CPU types in machine_run_board_init() for various boards
pci-host: designware: Limit value range of iATU viewport register
hw/arm: Convert some DPRINTF macros to trace events and guest errors
hw/arm: NPCM7XX SoC: Add GMAC ethernet controller devices
hw/arm: Implement BCM2835 SPI Controller
# -----BEGIN PGP SIGNATURE-----
#
# iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmW9C84ZHHBldGVyLm1h
# eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3qS6D/wM0/JGEYfaadpuMEOAx4PG
# AnfScbPqVhx9J31P2Ks3VrB5F108aq/SaL2BmCb3BLF/ECChlhBXIjd7ukdHstts
# F1TvqtvLGDZQz6wSVUeB0YOvAjGa3vIskn+Xvk9e6Ne6PcXgVnxAof/cPsXUiYNy
# 6DJjNiLJ/a9Xgq9rjFO6vzW3AL95U6/FmD2F0pOotWXERhNhoyYVV6RtyeqKlDQP
# yFVk5h601YURk9PeNZn9zpOpZqjAM7PxyF3X50N3Sv+G0uoKSr6b+c3/fDJbJo3+
# 0LXomEa8hdheQxm1dLY5OD0JX3bvYxwH41bDg9B0iEdjxUdXt6LfXI9Nvw9BAwix
# 8AcGJJUaL4XU4uPfHBpRJApM15+MRb0hqfv4ZcGk8e67IIqVeDbKL2clTQGoHSg1
# KaB0POhtFx//M/uBOyk/FR2gb2eBNU8GuoCgxdDwh0K5ylcaK1YPiX4Tcglu4iS0
# Frvazphb2pO1BK6JiJwN2/9ezzDkDJqTKoSqdc4g3ETVOGnxr+tXwcds3t2iK3g2
# y+pgijDOAT3bJO5kYeGvhoEJPKqXwJ3UQ8zTJsU2XSYwBjIyv5V3oOn6elwYJaWq
# yUDTC3QEK61KfnQnfTyLfdGWX1aVzHnYLWmQdO+3cczuQU0s0MP246Z1GAgDtgvD
# jGjDBz6mryWvP2H0xSmERQ==
# =azdP
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 02 Feb 2024 15:35:42 GMT
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# gpg: aka "Peter Maydell <peter@archaic.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* tag 'pull-target-arm-20240202' of https://git.linaro.org/people/pmaydell/qemu-arm: (36 commits)
hw/arm: Connect SPI Controller to BCM2835
hw/ssi: Implement BCM2835 SPI Controller
tests/qtest: Adding PCS Module test to GMAC Qtest
hw/net: GMAC Tx Implementation
hw/net: GMAC Rx Implementation
tests/qtest: Creating qtest for GMAC Module
hw/arm: Add GMAC devices to NPCM7XX SoC
hw/net: Add NPCMXXX GMAC device
hw/xen: convert stderr prints to error/warn reports
hw/xen/xen-hvm-common.c: convert DPRINTF to tracepoints
hw/xen/xen-mapcache.c: convert DPRINTF to tracepoints
hw/arm/xen_arm.c: convert DPRINTF to trace events and error/warn reports
hw/arm/z2: convert DPRINTF to trace events and guest errors
hw/arm/strongarm.c: convert DPRINTF to trace events and guest errors
pci-host: designware: Limit value range of iATU viewport register
hw/arm/zynq: Check for CPU types in machine_run_board_init()
hw/arm/vexpress: Check for CPU types in machine_run_board_init()
hw/arm/npcm7xx_boards: Simplify setting MachineClass::valid_cpu_types[]
hw/arm/musca: Simplify setting MachineClass::valid_cpu_types[]
hw/arm/msf2: Simplify setting MachineClass::valid_cpu_types[]
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
This function is no longer used, as all its callers have been converted
to use pci_init_nic_devices() instead.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
|
|
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
|
|
Obtain the MAC address from the NIC configuration if there is one, or
generate one explicitly so that it can be placed in the PROM.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
|
|
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Acked-by: Thomas Huth <thuth@redhat.com>
|
|
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
|
|
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
|
|
Create the device only if there is a corresponding NIC config for it.
Remove the explicit check on nd_table[0].used from hw/hppa/machine.c
which (since commit d8a3220005d7) tries to do the same thing.
The lasi_82596 support has been disabled since it was first introduced,
since enable_lasi_lan() has always been zero. This allows the user to
enable it by explicitly requesting a NIC model 'lasi_82596' or just
using the alias 'lasi'. Otherwise, it defaults to a PCI NIC as before.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
|
|
When converting to the shiny build-system-du-jour, a typo prevented the
last_i82596 driver from being built. Correct the config option name to
re-enable the build. And include "sysemu/sysemu.h" so it actually builds.
Fixes: b1419fa66558 ("meson: convert hw/net")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2144
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
|
|
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Thomas Huth <thuth@redhat.com>
|
