| Age | Commit message (Collapse) | Author |
|---|
|
For GPIE.NSICR, Section 7.3.2.1.2 says:
> ICR bits are cleared on register read. If GPIE.NSICR = 0b, then the
> clear on read occurs only if no bit is set in the IMS or at least one
> bit is set in the IMS and there is a true interrupt as reflected in
> ICR.INTA.
e1000e does similar though it checks for CTRL_EXT.IAME, which does not
exist on igb.
Suggested-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
This follows the corresponding change for e1000e. This fixes:
tests/avocado/netdev-ethtool.py:NetDevEthtool.test_igb
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
In MSI-X mode, if there are interrupts already notified but not cleared
and a new interrupt arrives, e1000e incorrectly notifies the notified
ones again along with the new one.
To fix this issue, replace e1000e_update_interrupt_state() with
two new functions: e1000e_raise_interrupts() and
e1000e_lower_interrupts(). These functions don't only raise or lower
interrupts, but it also performs register writes which updates the
interrupt state. Before it performs a register write, these function
determines the interrupts already raised, and compares with the
interrupts raised after the register write to determine the interrupts
to notify.
The introduction of these functions made tracepoints which assumes that
the caller of e1000e_update_interrupt_state() performs register writes
obsolete. These tracepoints are now removed, and alternative ones are
added to the new functions.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
igb has a configurable size limit for LPE, and uses different limits
depending on whether the packet is treated as a VLAN packet.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
e1000e does not support using UDP for RSS hash, but igb does.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
eth_strip_vlan and eth_strip_vlan_ex refers to ehdr_buf as struct
eth_header. Enforce alignment for the structure.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
It is possible to have another VLAN tag even if the packet is already
tagged.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Rename variable "n" to "causes", which properly represents the content
of the variable.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Rename variable "n" to "causes", which properly represents the content
of the variable.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Section 7.3.4.1 says:
> When auto-clear is enabled for an interrupt cause, the EICR bit is
> set when a cause event mapped to this vector occurs. When the EITR
> Counter reaches zero, the MSI-X message is sent on PCIe. Then the
> EICR bit is cleared and enabled to be set by a new cause event
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
The constants need to be consistent between the PF and VF.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Keeping Tx packet state after the transmit queue is emptied but this
behavior is unreliable as the state can be reset anytime the migration
happens.
Always reset Tx packet state always after the queue is emptied.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Keeping Tx packet state after the transmit queue is emptied has some
problems:
- The datasheet says the descriptors can be reused after the transmit
queue is emptied, but the Tx packet state may keep references to them.
- The Tx packet state cannot be migrated so it can be reset anytime the
migration happens.
Always reset Tx packet state always after the queue is emptied.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Section 7.2.2.3 Advanced Transmit Data Descriptor says:
> For frames that spans multiple descriptors, all fields apart from
> DCMD.EOP, DCMD.RS, DCMD.DEXT, DTALEN, Address and DTYP are valid only
> in the first descriptors and are ignored in the subsequent ones.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
The goto is a bit confusing as it changes the control flow only if L4
protocol is not recognized. It is also different from e1000e, and
noisy when comparing e1000e and igb.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Without this change, the status flags may not be traced e.g. if checksum
offloading is disabled.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Without this change, the status flags may not be traced e.g. if checksum
offloading is disabled.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
e1000e and igb employs NetPktRssIpV6TcpEx for RSS hash if TcpIpv6 MRQC
bit is set. Moreover, igb also has a MRQC bit for NetPktRssIpV6Tcp
though it is not implemented yet. Rename it to TcpIpv6Ex to avoid
confusion.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Section 13.7.15 Receive Length Error Count says:
> Packets over 1522 bytes are oversized if LongPacketEnable is 0b
> (RCTL.LPE). If LongPacketEnable (LPE) is 1b, then an incoming packet
> is considered oversized if it exceeds 16384 bytes.
> These lengths are based on bytes in the received packet from
> <Destination Address> through <CRC>, inclusively.
As QEMU processes packets without CRC, the number of bytes for CRC
need to be subtracted. This change adds some size definitions to be used
to derive the new size thresholds to eth.h.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
This saves some code and enables tracepoint for e1000's VLAN filtering.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
The old eth_setup_vlan_headers has no user so remove it and rename
eth_setup_vlan_headers_ex.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
This function is not used.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
igb_receive_internal() used to check the iov length to determine
copy the iovs to a contiguous buffer, but the check is flawed in two
ways:
- It does not ensure that iovcnt > 0.
- It does not take virtio-net header into consideration.
The size of this copy is just 22 octets, which can be even less than
the code size required for checks. This (wrong) optimization is probably
not worth so just remove it. Removing this also allows igb to assume
aligned accesses for the ethernet header.
Fixes: 3a977deebe ("Intrdocue igb device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
e1000e_receive_internal() used to check the iov length to determine
copy the iovs to a contiguous buffer, but the check is flawed in two
ways:
- It does not ensure that iovcnt > 0.
- It does not take virtio-net header into consideration.
The size of this copy is just 18 octets, which can be even less than
the code size required for checks. This (wrong) optimization is probably
not worth so just remove it.
Fixes: 6f3fbe4ed0 ("net: Introduce e1000e device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
igb does not properly ensure the buffer passed to
net_rx_pkt_set_protocols() is contiguous for the entire L2/L3/L4 header.
Allow it to pass scattered data to net_rx_pkt_set_protocols().
Fixes: 3a977deebe ("Intrdocue igb device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
The datasheet says contradicting statements regarding ICR accesses so it
is not reliable to determine the behavior of ICR accesses. However,
e1000e does clear IMS bits when reading ICR accesses and Linux also
expects ICR accesses will clear IMS bits according to:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/drivers/net/ethernet/intel/igb/igb_main.c?h=v6.2#n8048
Fixes: 3a977deebe ("Intrdocue igb device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
While the datasheet of e1000e says it checks CTRL.VME for tx VLAN
tagging, igb's datasheet has no such statements. It also says for
"CTRL.VLE":
> This register only affects the VLAN Strip in Rx it does not have any
> influence in the Tx path in the 82576.
(Appendix A. Changes from the 82575)
There is no "CTRL.VLE" so it is more likely that it is a mistake of
CTRL.VME.
Fixes: fba7c3b788 ("igb: respect VMVIR and VMOLR for VLAN")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
igb's advanced descriptor uses a packet type encoding different from
one used in e1000e's extended descriptor. Fix the logic to encode
Rx packet type accordingly.
Fixes: 3a977deebe ("Intrdocue igb device emulation")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Before this change, e1000 and the common code updated BPRC and MPRC
depending on the matched filter, but e1000e and igb decided to update
those counters by deriving the packet type independently. This
inconsistency caused a multicast packet to be counted twice.
Updating BPRC and MPRC depending on are fundamentally flawed anyway as
a filter can be used for different types of packets. For example, it is
possible to filter broadcast packets with MTA.
Always determine what counters to update by inspecting the packets.
Fixes: 3b27430177 ("e1000: Implementing various counters")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
This allows to use the network packet abstractions even if PCI is not
used.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
This is intended to be followed by another change for the interface.
It also fixes the leak of memory mapping when the specified memory is
partially mapped.
Fixes: e263cd49c7 ("Packet abstraction for VMWARE network devices")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
The bytes and packets counter registers are cleared on read.
Copying the "total counter" registers to the "good counter" registers has
side effects.
If the "total" register is never read by the OS, it only gets incremented.
This leads to exponential growth of the "good" register.
This commit increments the counters individually to avoid this.
Signed-off-by: Timothée Cocault <timothee.cocault@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Announce the default NIC via MachineClass->default_nic and set up
MachineClass->no_parallel according to the availability of the
"isa-parallel" device, so that the Sun machines also work when
QEMU has been configured with "--without-default-devices".
Message-Id: <20230512124033.502654-11-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
|
|
Don't try to instantiate the parallel port if it has not been
enabled in the build configuration.
Message-Id: <20230512124033.502654-10-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
|
|
We are going to require the macro from other files, too, so move
this #define to the header file.
Message-Id: <20230512124033.502654-9-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
|
|
Mark the default NIC via the new MachineClass->default_nic setting
so that the machine-defaults code in vl.c can decide whether the
default NIC is usable or not (for example when compiling with the
"--without-default-devices" configure switch).
Message-Id: <20230512124033.502654-8-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
|
|
Mark the default NIC via the new MachineClass->default_nic setting
so that the machine-defaults code in vl.c can decide whether the
default NIC is usable or not (for example when compiling with the
"--without-default-devices" configure switch).
Message-Id: <20230512124033.502654-7-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
|
|
Mark the default NIC via the new MachineClass->default_nic setting
so that the machine-defaults code in vl.c can decide whether the
default NIC is usable or not (for example when compiling with the
"--without-default-devices" configure switch).
Message-Id: <20230512124033.502654-6-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
|
|
We are going to re-use this setting for other targets, so let's
move this to the main MachineClass.
Message-Id: <20230512124033.502654-4-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
|
|
The "isapc" machine can also be run without VGA card, so there
is no need for a hard requirement with a "select" here - "imply"
is enough.
Message-Id: <20230512124033.502654-2-thuth@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
|
|
into staging
virtio,pc,pci: fixes, features, cleanups
CXL volatile memory support
More memslots for vhost-user on x86 and ARM.
vIOMMU support for vhost-vdpa
pcie-to-pci bridge can now be compiled out
MADT revision bumped to 3
Fixes, cleanups all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# -----BEGIN PGP SIGNATURE-----
#
# iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmRniWoPHG1zdEByZWRo
# YXQuY29tAAoJECgfDbjSjVRpN4MH/RqdvHmujrjvjzXbbN/gq87Njp+kQLKEooIE
# ZkqdNaVUE6vjCH8iU+chjsxt4VSquSjOL9CWWrYefEIeqCFLWsuXSAY0VDAbY67x
# +aes51tTYILVsx7fbb+T5mJKRgVuWW4C5KaGeQ1djSexy42nvplZUJdIJUhZr0t9
# dzzOsD+mezHS7Xu2QOzSfl5QQRuOVVJnjJXkqJG/yRvHrZM5aTolatr/X7jNGedm
# 4oyMsVMaAcQ+dnEQigRJodf/MpFfs9DfNZAH55VwwQWsNT0t0ueD0xigR203jjaE
# mJJJipAqetFax2JjC7QMXWf+LR36BnL/0/xH+x/BWb0FI42wr0I=
# =ajmR
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 19 May 2023 07:36:26 AM PDT
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [undefined]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [undefined]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* tag 'for_upstream' of https://git.kernel.org/pub/scm/virt/kvm/mst/qemu: (40 commits)
hw/i386/pc: No need for rtc_state to be an out-parameter
hw/i386/pc: Create RTC controllers in south bridges
hw/cxl: Introduce cxl_device_get_timestamp() utility function
hw/cxl: rename mailbox return code type from ret_code to CXLRetCode
hw/pci-bridge: make building pcie-to-pci bridge configurable
virtio-pci: add handling of PCI ATS and Device-TLB enable/disable
hw/pci-host/pam: Make init_pam() usage more readable
hw/i386/pc: Initialize ram_memory variable directly
hw/i386/pc_{q35,piix}: Minimize usage of get_system_memory()
hw/i386/pc_{q35,piix}: Reuse MachineClass::desc as SMB product name
hw/i386/pc_q35: Reuse machine parameter
hw/pci-host/q35: Inline sysbus_add_io()
hw/pci-host/i440fx: Inline sysbus_add_io()
vhost-vdpa: Add support for vIOMMU.
vhost-vdpa: Add check for full 64-bit in region delete
vhost_vdpa: fix the input in trace_vhost_vdpa_listener_region_del()
vhost: expose function vhost_dev_has_iommu()
virtio-crypto: fix NULL pointer dereference in virtio_crypto_free_request
virtio-net: not enable vq reset feature unconditionally
vhost-user: Remove acpi-specific memslot limit
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
