| Age | Commit message (Collapse) | Author |
|---|
|
Voiding the ITS caches is not supposed to happen via
individual register writes. So we introduced a dedicated
ITS KVM device ioctl to perform a cold reset of the ITS:
KVM_DEV_ARM_VGIC_GRP_CTRL/KVM_DEV_ARM_ITS_CTRL_RESET. Let's
use this latter if the kernel supports it.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1511883692-11511-5-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
At the moment the ITS is not properly reset and this causes
various bugs on save/restore. We implement a minimalist reset
through individual register writes but for kernel versions
before v4.15 this fails voiding the vITS cache. We cannot
claim we have a comprehensive reset (hence the error message)
but that's better than nothing.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1511883692-11511-3-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
From the very beginning, post_load() was called from common
reset. This is not standard and obliged to discriminate the
reset case from the restore case using the iidr value.
Let's get rid of that call.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1511883692-11511-2-git-send-email-eric.auger@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add support for the ZynqMP QSPI (consisting of the Generic QSPI and Legacy
QSPI) and connect Numonyx n25q512a11 flashes to it.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20171126231634.9531-14-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add support for the Zynq Ultrascale MPSoc Generic QSPI.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-13-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Don't set TX FIFO UNDERFLOW interrupt after transmitting the commands.
Also update interrupts after reading out the interrupt status.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-12-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add support for 4 byte addresses in the LQSPI and correct LQSPI_CFG_SEP_BUS.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-11-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add support for zero pumping according to the transfer size register.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-10-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Make tx/rx_data_bytes more generic so they can be reused (when adding
support for the Zynqmp Generic QSPI).
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-9-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add support for the RX discard and RX drain functionality. Also transmit
one byte per dummy cycle (to the flash memories) with commands that require
these.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-8-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Update striping functionality to be big-endian bit order (as according to
the Zynq-7000 Technical Reference Manual). Output thereafter the even bits
into the flash memory connected to the lower QSPI bus and the odd bits into
the flash memory connected to the upper QSPI bus.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-7-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Move the FlashCMD enum, XilinxQSPIPS and XilinxSPIPSClass structures to the
header for consistency (struct XilinxSPIPS is found there). Also move out
a define and remove two double included headers (while touching the code).
Finally, add 4 byte address commands to the FlashCMD enum.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-6-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add support for Micron (Numonyx) n25q512a11 and n25q512a13 flashes.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Acked-by: Marcin Krzemiński <mar.krzeminski@gmail.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-5-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add support for the bank address register access commands (BRRD/BRWR) and
the BULK_ERASE (0x60) command.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Acked-by: Marcin Krzemiński <mar.krzeminski@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-4-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add support for SST READ ID 0x90/0xAB commands for reading out the flash
manufacturer ID and device ID.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20171126231634.9531-3-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add support for continuous read out of the RDSR and READ_FSR status
registers until the chip select is deasserted. This feature is supported
by amongst others 1 or more flashtypes manufactured by Numonyx (Micron),
Windbond, SST, Gigadevice, Eon and Macronix.
Signed-off-by: Francisco Iglesias <frasse.iglesias@gmail.com>
Acked-by: Marcin Krzemiński<mar.krzeminski@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Tested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Message-id: 20171126231634.9531-2-frasse.iglesias@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Commit 5c0919d02066 ("virtio-scsi: Add virtqueue_size parameter allowing
virtqueue size to be set.") introduced a new parameter to virtio-scsi.
Later, commit 920036106044 ("vhost-user-scsi: add missing virtqueue_size
param") added that parameter to the new vhost-user-scsi interface but
neglected the existing vhost-scsi interface it was built on.
Apply the same change to vhost-scsi, so that we can boot a guest with
a device defined. This also avoids crashing a guest when hotplugging
a vhost-scsi device.
Signed-off-by: Eric Farman <farman@linux.vnet.ibm.com>
Message-id: 20171201151538.6844-2-farman@linux.vnet.ibm.com
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
pc, pci, virtio: fixes for rc3
A bunch of fixes all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Fri 01 Dec 2017 17:06:33 GMT
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
pc: fix crash on attempted cpu unplug
virtio: check VirtQueue Vring object is set
vhost: fix error check in vhost_verify_ring_mappings()
dump-guest-memory.py: fix No symbol "vmcoreinfo_find"
vhost: restore avail index from vring used index on disconnection
virtio: Add queue interface to restore avail index from vring used index
i386/msi: Correct mask of destination ID in MSI address
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
At guest reset time, we allocate a hash page table (HPT) for the guest
based on the guest's RAM size. If dynamic HPT resizing is not available we
use the maximum RAM size, if it is we use the current RAM size.
But the "current RAM size" calculation is incorrect - we just use the
"base" ram_size from the machine structure. This doesn't include any
pluggable DIMMs that are already plugged at reset time.
This means that if you try to start a 'pseries' machine with a DIMM
specified on the command line that's much larger than the "base" RAM size,
then the guest will get a woefully inadequate HPT. This can lead to a
guest freeze during boot as it runs out of HPT space during initial MMU
setup.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
|
|
when qemu is started with '-no-acpi' CLI option, an attempt
to unplug a CPU using device_del results in null pointer
dereference at:
#0 object_get_class
#1 pc_machine_device_unplug_request_cb
#2 qmp_marshal_device_del
which is caused by pcms->acpi_dev == NULL due to ACPI support
being disabled.
Considering that ACPI support is necessary for unplug to work,
check that it's enabled and fail unplug request gracefully
if no acpi device were found.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
A guest could attempt to use an uninitialised VirtQueue object
or unset Vring.align leading to a arithmetic exception. Add check
to avoid it.
Reported-by: Zhangboxian <zhangboxian@huawei.com>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
|
|
Since commit f1f9e6c5 "vhost: adapt vhost_verify_ring_mappings() to
virtio 1 ring layout", we check the mapping of each part (descriptor
table, available ring and used ring) of each virtqueue separately.
The checking of a part is done by the vhost_verify_ring_part_mapping()
function: it returns either 0 on success or a negative errno if the
part cannot be mapped at the same place.
Unfortunately, the vhost_verify_ring_mappings() function checks its
return value the other way round. It means that we either:
- only verify the descriptor table of the first virtqueue, and if it
is valid we ignore all the other mappings
- or ignore all broken mappings until we reach a valid one
ie, we only raise an error if all mappings are broken, and we consider
all mappings are valid otherwise (false success), which is obviously
wrong.
This patch ensures that vhost_verify_ring_mappings() only returns
success if ALL mappings are okay.
Reported-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
vhost_virtqueue_stop() gets avail index value from the backend,
except if the backend is not responding.
It happens when the backend crashes, and in this case, internal
state of the virtio queue is inconsistent, making packets
to corrupt the vring state.
With a Linux guest, it results in following error message on
backend reconnection:
[ 22.444905] virtio_net virtio0: output.0:id 0 is not a head!
[ 22.446746] net enp0s3: Unexpected TXQ (0) queue failure: -5
[ 22.476360] net enp0s3: Unexpected TXQ (0) queue failure: -5
Fixes: 283e2c2adcb8 ("net: virtio-net discards TX data after link down")
Cc: qemu-stable@nongnu.org
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
In case of backend crash, it is not possible to restore internal
avail index from the backend value as vhost_get_vring_base
callback fails.
This patch provides a new interface to restore internal avail index
from the vring used index, as done by some vhost-user backend on
reconnection.
Signed-off-by: Maxime Coquelin <maxime.coquelin@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Migration of pseries is broken with TCG because
QEMU tries to restore KVM MMU state unconditionally.
The result is a SIGSEGV in kvm_vm_ioctl():
#0 kvm_vm_ioctl (s=0x0, type=-2146390353)
at qemu/accel/kvm/kvm-all.c:2032
#1 0x00000001003e3e2c in kvmppc_configure_v3_mmu (cpu=<optimized out>,
radix=<optimized out>, gtse=<optimized out>, proc_tbl=<optimized out>)
at qemu/target/ppc/kvm.c:396
#2 0x00000001002f8b88 in spapr_post_load (opaque=0x1019103c0,
version_id=<optimized out>) at qemu/hw/ppc/spapr.c:1578
#3 0x000000010059e4cc in vmstate_load_state (f=0x106230000,
vmsd=0x1009479e0 <vmstate_spapr>, opaque=0x1019103c0,
version_id=<optimized out>) at qemu/migration/vmstate.c:165
#4 0x00000001005987e0 in vmstate_load (f=<optimized out>, se=<optimized out>)
at qemu/migration/savevm.c:748
This patch fixes the problem by not calling the KVM function with the
TCG mode.
Fixes: d39c90f5f3 ("spapr: Fix migration of Radix guests")
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Reviewed-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Guest state should not be touched if VM is stopped, unfortunately we
didn't check running state and tried to drain tx queue unconditionally
in virtio_net_set_status(). A crash was then noticed as a migration
destination when user type quit after virtqueue state is loaded but
before region cache is initialized. In this case,
virtio_net_drop_tx_queue_data() tries to access the uninitialized
region cache.
Fix this by only dropping tx queue data when vm is running.
Fixes: 283e2c2adcb80 ("net: virtio-net discards TX data after link down")
Cc: Yuri Benditovich <yuri.benditovich@daynix.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
The patb_entry is used to store the location of the process table in
guest memory. The msb is also used to indicate the mmu mode of the
guest, that is patb_entry & 1 << 63 ? radix_mode : hash_mode.
Currently we set this to zero in spapr_setup_hpt_and_vrma() since if
this function gets called then we know we're hash. However some code
paths, such as setting up the hpt on incoming migration of a hash guest,
call spapr_reallocate_hpt() directly bypassing this higher level
function. Since we assume radix if the host is capable this results in
the msb in patb_entry being left set so in spapr_post_load() we call
kvmppc_configure_v3_mmu() and tell the host we're radix which as
expected means addresses cannot be translated once we actually run the cpu.
To fix this move the zeroing of patb_entry into spapr_reallocate_hpt().
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Add virt-2.11 machine type.
Signed-off-by: Eric Auger <eric.auger@redhat.com>
Message-id: 1511516626-21178-1-git-send-email-eric.auger@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
We no longer support the old s390 transport, neither does the newest
Linux kernel. Remove it from the linux header script as well as the
s390x virtio code. We still should handle the VIRTIO_NOTIFY hypercall,
to tolerate early printk on older guest kernels without an sclp console.
We continue to ignore these events.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Message-Id: <20171115154223.109991-1-borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
|
|
The spapr-vty device implements the PAPR defined virtual console,
which is also implemented by IBM's proprietary PowerVM hypervisor.
PowerVM's implementation has a bug where it inserts an extra \0 after
every \r going to the guest. Because of that Linux's guest side
driver has a workaround which strips \0 characters that appear
immediately after a \r.
That means that when running under qemu, sending a binary stream from
host to guest via spapr-vty which happens to include a \r\0 sequence
will get corrupted by that workaround.
To deal with that, this patch duplicates PowerVM's bug, inserting an
extra \0 after each \r. Ugly, but the best option available.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Greg Kurz <groug@kaod.org>
|
|
LUNs >= 256 have to be encoded with the so-called "flat space
addressing method" for virtio-scsi, where an additional bit has to
be set. SLOF already took care of this with the following commit:
https://git.qemu.org/?p=SLOF.git;a=commitdiff;h=f72a37713fea47da
(see https://bugzilla.redhat.com/show_bug.cgi?id=1431584 for details)
But QEMU does not use this encoding yet for device tree paths
that have to be handed over to SLOF to deal with the "bootindex"
property, so SLOF currently fails to boot from virtio-scsi devices
with LUNs >= 256 in the right boot order. Fix it by using the bit
to indicate the "flat space addressing method" for LUNs >= 256.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
'remotes/pmaydell/tags/pull-target-arm-20171120' into staging
target-arm queue:
* hw/arm: Silence xlnx-ep108 deprecation warning during tests
* hw/arm/aspeed: Unlock SCU when running kernel
* arm: check regime, not current state, for ATS write PAR format
* nvic: Fix ARMv7M MPU_RBAR reads
* target/arm: Report GICv3 sysregs present in ID registers if needed
# gpg: Signature made Mon 20 Nov 2017 17:35:25 GMT
# gpg: using RSA key 0x3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20171120:
hw/arm: Silence xlnx-ep108 deprecation warning during tests
hw/arm/aspeed: Unlock SCU when running kernel
arm: check regime, not current state, for ATS write PAR format
nvic: Fix ARMv7M MPU_RBAR reads
target/arm: Report GICv3 sysregs present in ID registers if needed
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
into staging
ppc patch queue 2017-11-20
Here's the current queue of ppc patches. These 2 patches are both
more complex than I'd ideally like this late in the 2.11 cycle.
However, they do fix important bugs, so I think it's worth it on
balance.
# gpg: Signature made Mon 20 Nov 2017 03:27:19 GMT
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.11-20171120:
spapr: reset DRCs after devices
target/ppc: Update setting of cpu features to account for compat modes
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The new deprecation warning for the xlnx-ep108 machine also pops up
during "make check" which is kind of confusing. Silence it if testing
mode is enabled.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Acked-by: Wei Huang <wei@redhat.com>
Message-id: 1510846183-756-1-git-send-email-thuth@redhat.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The ASPEED hardware contains a lock register for the SCU that disables
any writes to the SCU when it is locked. The machine comes up with the
lock enabled, but on all known hardware u-boot will unlock it and leave
it unlocked when loading the kernel.
This means the kernel expects the SCU to be unlocked. When booting from
an emulated ROM the normal u-boot unlock path is executed. Things don't
go well when booting using the -kernel command line, as u-boot does not
run first.
Change behaviour so that when a kernel is passed to the machine, set the
reset value of the SCU to be unlocked.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-id: 20171114122018.12204-1-joel@jms.id.au
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Fix an incorrect mask expression in the handling of v7M MPU_RBAR
reads that meant that we would always report the ADDR field as zero.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1509732813-22957-1-git-send-email-peter.maydell@linaro.org
|
|
Since commit ab06ec43577177a442e8 we test the vmxnet3 device in the
pxe-tester, too (when running "make check SPEED=slow"). This now
revealed that the code is not working there if the host is a big
endian machine (for example ppc64 or s390x) - "make check SPEED=slow"
is now failing on such hosts.
The vmxnet3 code lacks endianness conversions in a couple of places.
Interestingly, the bitfields in the structs in vmxnet3.h already tried to
take care of the *bit* endianness of the C compilers - but the code missed
to change the *byte* endianness when reading or writing the corresponding
structs. So the bitfields are now wrapped into unions which allow to change
the byte endianness during runtime with the non-bitfield member of the union.
With these changes, "make check SPEED=slow" now properly works on big endian
hosts, too.
Reported-by: David Gibson <dgibson@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: David Gibson <dgibson@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
The checksum algorithm used by IPv4, TCP and UDP allows a zero value
to be represented by either 0x0000 and 0xFFFF. But per RFC 768, a zero
UDP checksum must be transmitted as 0xFFFF because 0x0000 is a special
value meaning no checksum.
Substitute 0xFFFF whenever a checksum is computed as zero when
modifying a UDP datagram header. Doing this on IPv4 and TCP checksums
is unnecessary but legal. Add a wrapper for net_checksum_finish() that
makes the substitution.
(We can't just change net_checksum_finish(), as that function is also
used by receivers to verify checksums, and in that case the expected
value is always 0x0000.)
Signed-off-by: Ed Swierk <eswierk@skyportsystems.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Since commit 1865e288a823c764cd4344d ("Fix eepro100 simple transmission
mode"), the test/pxe-test is broken for the eepro100 device on big
endian hosts. However, it seems like that commit did not introduce the
problem, but just uncovered it: The EEPRO100State->tx.tbd_array_addr and
EEPRO100State->tx.tcb_bytes fields are already in host byte order, since
they have already been byte-swapped in the read_cb() function.
Thus byte-swapping them in tx_command() again results in the wrong
endianness. Removing the byte-swapping here fixes the pxe-test.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
This reverts commit 5e89dc01133f8f5e621f6b66b356c6f37d31dafb since:
- we should use ID in the spec instead the one used by OEM
- in the future, we should allow changing id through either property
or EEPROM file.
Cc: Stefan Weil <sw@weilnetz.de>
Cc: Michael Nawrocki <michael.nawrocki@gtri.gatech.edu>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
A DRC with a pending unplug request releases its associated device at
machine reset time.
In the case of LMB, when all DRCs for a DIMM device have been reset,
the DIMM gets unplugged, causing guest memory to disappear. This may
be very confusing for anything still using this memory.
This is exactly what happens with vhost backends, and QEMU aborts
with:
qemu-system-ppc64: used ring relocated for ring 2
qemu-system-ppc64: qemu/hw/virtio/vhost.c:649: vhost_commit: Assertion
`r >= 0' failed.
The issue is that each DRC registers a QEMU reset handler, and we
don't control the order in which these handlers are called (ie,
a LMB DRC will unplug a DIMM before the virtio device using the
memory on this DIMM could stop its vhost backend).
To avoid such situations, let's reset DRCs after all devices
have been reset.
Reported-by: Mallesh N. Koti <mallesh@linux.vnet.ibm.com>
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The device tree nodes ibm,arch-vec-5-platform-support and ibm,pa-features
are used to communicate features of the cpu to the guest operating
system. The properties of each of these are determined based on the
selected cpu model and the availability of hypervisor features.
Currently the compatibility mode of the cpu is not taken into account.
The ibm,arch-vec-5-platform-support node is used to communicate the
level of support for various ISAv3 processor features to the guest
before CAS to inform the guests' request. The available mmu mode should
only be hash unless the cpu is a POWER9 which is not in a prePOWER9
compat mode, in which case the available modes depend on the
accelerator and the hypervisor capabilities.
The ibm,pa-featues node is used to communicate the level of cpu support
for various features to the guest os. This should only contain features
relevant to the operating mode of the processor, that is the selected
cpu model taking into account any compat mode. This means that the
compat mode should be taken into account when choosing the properties of
ibm,pa-features and they should match the compat mode selected, or the
cpu model selected if no compat mode.
Update the setting of these cpu features in the device tree as described
above to properly take into account any compat mode. We use the
ppc_check_compat function which takes into account the current processor
model and the cpu compat mode.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
pc, pci, virtio: fixes for rc1
A bunch of fixes all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Thu 16 Nov 2017 16:37:21 GMT
# gpg: using RSA key 0x281F0DB8D28D5469
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>"
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>"
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
tests/bios-tables-test: Fix endianess problems when passing data to iasl
build-sys: restrict vmcoreinfo to fw_cfg+dma capable targets
vmcoreinfo: put it in the 'misc' device category
NUMA: Enable adding NUMA node implicitly
tests/acpi-test-data: update _CRS in DSDT
hw/pcie-pci-bridge: restrict to X86 and ARM
hw/pci-host: Fix x86 Host Bridges 64bit PCI hole
pci: Initialize pci_dev->name before use
fix: unrealize virtio device if we fail to hotplug it
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
vmcoreinfo is built for all targets. However, it requires fw_cfg with
DMA operations support (write operation). Restrict vmcoreinfo exposure
to architectures that are supporting FW_CFG_DMA, that is arm-virt and
x86 only atm.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com>
Tested-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Linux and Windows need ACPI SRAT table to make memory hotplug work properly,
however currently QEMU doesn't create SRAT table if numa options aren't present
on CLI.
Which breaks both linux and windows guests in certain conditions:
* Windows: won't enable memory hotplug without SRAT table at all
* Linux: if QEMU is started with initial memory all below 4Gb and no SRAT table
present, guest kernel will use nommu DMA ops, which breaks 32bit hw drivers
when memory is hotplugged and guest tries to use it with that drivers.
Fix above issues by automatically creating a numa node when QEMU is started with
memory hotplug enabled but without '-numa' options on CLI.
(PS: auto-create numa node only for new machine types so not to break migration).
Which would provide SRAT table to guests without explicit -numa options on CLI
and would allow:
* Windows: to enable memory hotplug
* Linux: switch to SWIOTLB DMA ops, to bounce DMA transfers to 32bit allocated
buffers that legacy drivers/hw can handle.
[Rewritten by Igor]
Reported-by: Thadeu Lima de Souza Cascardo <cascardo@canonical.com>
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Thomas Huth <thuth@redhat.com>
Cc: Alistair Francis <alistair23@gmail.com>
Cc: Takao Indoh <indou.takao@jp.fujitsu.com>
Cc: Izumi Taku <izumi.taku@jp.fujitsu.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The PCIE-PCI bridge is specific to "pure" PCIe systems
(on QEMU we have X86 and ARM), it does not make sense to
have it in other archs.
Reported-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Yongbok Kim <yongbok.kim@mips.com>
|
|
Currently there is no MMIO range over 4G
reserved for PCI hotplug. Since the 32bit PCI hole
depends on the number of cold-plugged PCI devices
and other factors, it is very possible is too small
to hotplug PCI devices with large BARs.
Fix it by reserving 2G for I4400FX chipset
in order to comply with older Win32 Guest OSes
and 32G for Q35 chipset.
Even if the new defaults of pci-hole64-size will appear in
"info qtree" also for older machines, the property was
not implemented so no changes will be visible to guests.
Note this is a regression since prev QEMU versions had
some range reserved for 64bit PCI hotplug.
Reviewed-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This moves pci_dev->name initialization earlier so
pci_dev->bus_master_as could get a name instead of an empty string.
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
If we fail to hotplug virtio-blk device and then suspend
or shutdown VM, qemu is likely to crash.
Re-production steps:
1. Run VM named vm001
2. Create a virtio-blk.xml which contains wrong configurations:
<disk device="lun" rawio="yes" type="block">
<driver cache="none" io="native" name="qemu" type="raw" />
<source dev="/dev/mapper/11-dm" />
<target bus="virtio" dev="vdx" />
</disk>
3. Run command : virsh attach-device vm001 virtio-blk.xml
error: Failed to attach device from blk-scsi.xml
error: internal error: unable to execute QEMU command 'device_add': Please set scsi=off for virtio-blk devices in order to use virtio 1.0
it means hotplug virtio-blk device failed.
4. Suspend or shutdown VM will leads to qemu crash
Problem happens in virtio_vmstate_change which is called by
vm_state_notify:
vdev’s parent_bus is NULL, so qdev_get_parent_bus(DEVICE(vdev)) will crash.
virtio_vmstate_change is added to the list vm_change_state_head at virtio_blk_device_realize(virtio_init),
but after hotplug virtio-blk failed, virtio_vmstate_change will not be removed from vm_change_state_head.
Adding unrealize function of virtio-blk device can solve this problem.
Signed-off-by: linzhecheng <linzhecheng@huawei.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
