| Age | Commit message (Collapse) | Author |
|---|
|
It isn't unusual to happen, for example during reboot when the guest
doesn't reveice events for a while. So better don't flood stderr
with alarming messages. Turn them into tracepoints instead so they
can be enabled in case they are needed for trouble-shooting.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1466675495-28797-1-git-send-email-kraxel@redhat.com
|
|
Last round of s390x patches for 2.7:
- A large update of the s390x PCI code, bringing it in line with
the architecture
- Fixes and improvements in the ipl (boot) code
- Refactoring in the css code
# gpg: Signature made Mon 11 Jul 2016 09:04:51 BST
# gpg: using RSA key 0xDECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20160711: (25 commits)
s390x/pci: make hot-unplug handler smoother
s390x/pci: replace fid with idx in msg data of msix
s390x/pci: fix stpcifc_service_call
s390x/pci: refactor list_pci
s390x/pci: refactor s390_pci_find_dev_by_idx
s390x/pci: add checkings in CLP_SET_PCI_FN
s390x/pci: enable zpci hot-plug/hot-unplug
s390x/pci: enable uid-checking
s390x/pci: introduce S390PCIBusDevice qdev
s390x/pci: introduce S390PCIIOMMU
s390x/pci: introduce S390PCIBus
s390x/pci: enforce zPCI state checking
s390x/pci: refactor s390_pci_find_dev_by_fh
s390x/pci: unify FH_ macros
s390x/pci: write fid in CLP_QUERY_PCI_FN
s390x/pci: acceleration for getting S390pciState
s390x/pci: fix failures of dma map/unmap
s390x/css: Unplug handler of virtual css bridge
s390x/css: Factor out virtual css bridge and bus
s390x/css: use define for "virtual-css-bridge" literal
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The current implementation of hot-unplug handler is abrupt. Any pci
operation will be just rejected if pci device is unconfigured. Thus a
pci device can not be reset or destroyed in a right, smooth and safe
way.
Improve this as follows:
- Notify the guest via a HP_EVENT_DECONFIGURE_REQUEST(0x303) event in
the unplug handler, giving it a chance to deconfigure the device via
sclp and allowing us to continue hot-unplug afterwards.
- Set up a timer that will generate the HP_EVENT_CONFIGURE_TO_STBRES
(0x304) event as before if the guest did not react after an adequate
time.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
Present code uses fid as the part of message data of msix for looking
up the specific zpci device. However it limits the usable range of fid,
and the code looking up the zpci device may fail due to truncation of
the fid.
In addition, fh is composed of enabled bit, FH_VIRT and the array index.
So we can use the array index as the identifier to store in msg data.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
Firstly the function misses dmaas checking. This patch adds it.
Secondly the function uses s390_pci_find_dev_by_fh() to look up the
zpci device. This may fail if the guest provides a valid and disabled
fh but fh of the associated zpci device is enabled. Thus we use
s390_pci_find_dev_by_idx() instead.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
Because of the refactor of s390_pci_find_dev_by_idx(), list_pci()
should be updated. We introduce a new function to get the next
available zpci device. It simplifies the code of looking up zpci
devices.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
s390_find_dev_by_idx() only indexes usable zpci devices. It implies
that the index value of each zpci device is dynamic and may change if
a new zpci device is plugged. So we have to use a constant index to
look up the device.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
The code in CLP_SET_PCI_FN case misses some checkings. Let's add
them.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
We need to support hot-plug/hot-unplug for the new zpci devices as
well. This patch enables the present hot-plug/hot-unplug handlers
to support not only generic pci devices but also zpci devices.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
The uid-checking facility guarantees uniqueness of the uid within the
vm and exposes the real uid to the guest when listing pci devices.
Let's always enable it and present it to the guest in the response to
the list pci clp command.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
To support definitions of s390 pci attributes in Qemu cmdline, we have
to make current S390PCIBusDevice struct inherit DeviceState and add
three properties for it. Currently we only support definitions of uid
and fid.
'uid' is optionally defined by users, identifies a zpci device and
must be defined with a 16-bit and non-zero unique value.
'fid' ranges from 0x0 to 0xFFFFFFFF. For fid property, we introduce a
new PropertyInfo by the name of s390_pci_fid_propinfo with our special
setter and getter. As 'fid' is optional, introduce 'fid_defined' to
track whether the user specified a fid.
'target' field is to direct qemu to find the corresponding generic PCI
device. It is equal to the 'id' value of one of generic pci devices.
If the user doesn't specify 'id' parameter for a generic pci device,
its 'id' value will be generated automatically and use this value as
'target' to create an associated zpci device.
If the user did not specify 'uid' or 'fid', values are generated
automatically. 'target' is required.
In addition, if a pci device has no associated zpci device, the code
will generate a zpci device automatically for it.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
Currently each zpci device holds its own DMA address space and memory
region. At the same time, all instances of zpci device are stored in
S390pciState. So duirng the initialization of S390pciState, all zpci
devices are created and then all DMA address spaces are created. Thus,
when initializing pci devices, their corresponding DMA address spaces
could be found.
But zpci qdev will be introduced later. Zpci device may be initialized
and plugged afterwards generic pci device. So we should initialize all
DMA address spaces and memory regions before initializing zpci devices.
We introduce a new struct named S390PCIIOMMU. And a new field of
S390pciState, which is an array to store all instances of S390PCIIOMMU,
is added so that qemu pci code could find the corresponding DMA
address space when initializing a generic pci device. And this should
be done before the connection of a zpci device and a generic pci
device is built.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
To enable S390PCIBusDevice as qdev, there should be a new bus to
plug and manage all instances of S390PCIBusDevice. Due to this,
S390PCIBus is introduced.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
Current code uses some fields combinatorially to indicate the state of
a s390 pci device. This patch introduces device states in order to make
the code more readable and more logical.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
Because this function is called very frequently, we should use a more
effective way to find the zpci device. So we use the FH's index to get
the device directly.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
Present code uses some macros to structure PCI Function Handle. But
their names don't have a uniform format. Let's use FH_MASK_ as the
unified prefix.
While we're at it, differentiate the SHM bits: use different bits for
vfio and emulated devices.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
We forgot to write the fid; fix that.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
There are a number of places where the code needs to get the instance
of S390pciState. It calls object_resolve_path() every time. This
wastes a lot of time and leads to low performance. Thus we add
s390_get_phb() to improve it.
Because we always have a phb, we remove all return checkings in the
callers and add an assert in s390_get_phb() to make sure that phb is
getted successfully.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
In commit d78c19b5cf4821d0c198f4132a085bdbf19dda4c, vfio code stores
the IOMMU's offset_within_address_space and adjusts the IOVA before
calling vfio_dma_map/vfio_dma_unmap. But s390_translate_iommu already
considers the base address of an IOMMU memory region.
Thus we use pal as the size and 0x0 as the base address to initialize
IOMMU memory subregion.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Reviewed-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
The previous patch moved virtual css bridge and bus out from
virtio-ccw, but kept the direct reference of virtio-ccw specific
unplug function inside css-bridge.c.
To make the virtual css bus and bridge useful for non-virtio devices,
this introduces a common unplug function pointer "unplug" to call
specific virtio-ccw unplug parts. Thus, the tight coupling to
virtio-ccw can be removed.
This unplug pointer is a member of CCWDeviceClass, which is introduced
as an abstract device layer called "ccw-device". This layer is between
DeviceState and specific devices which are plugged in virtual css bus,
like virtio-ccw device. The specific unplug handlers should be assigned
to "unplug" during initialization.
Signed-off-by: Jing Liu <liujbjl@linux.vnet.ibm.com>
Reviewed-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
Currently, common base layers virtual css bridge and bus are
defined in hw/s390x/virtio-ccw.c(h). In order to support
multiple types of devices in the virtual channel subsystem,
especially non virtio-ccw, refactoring work needs to be done.
This work is just a pure code move without any functional change
except dropping an empty function virtual_css_bridge_init() and
virtio_ccw_busdev_unplug() changing. virtio_ccw_busdev_unplug()
is specific to virtio-ccw but gets referenced from the common
virtual css bridge code. To keep the functional changes to a
minimum we export this function from virtio-ccw.c and continue
to reference it inside virtual_css_bridge_class_init()
(now living in hw/s390x/css-bridge.c). A follow-up patch will
clean this up.
Signed-off-by: Jing Liu <liujbjl@linux.vnet.ibm.com>
Reviewed-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
Introduce a TYPE_* define (like we already use for a couple of other
QOM types) for the name of the virtual CSS bridge QOM type instead of
sprinkling the same string literal over several source files.
Signed-off-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
A lot of what virtio_ccw_device_realize() does isn't specific to
virtio; it would apply to emulated CCW as well. Factor it out to make
it easier to implement emulated CCW devices later on.
Signed-off-by: Sascha Silbe <silbe@linux.vnet.ibm.com>
Reviewed-by: Dong Jia Shi <bjsdjshi@linux.vnet.ibm.com>
Reviewed-by: Halil Pasic <pasic@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
When migrating from a different QEMU version, the start_address and
bios_start_address may differ. During migration these values are migrated
and overwrite the values that were detected by QEMU itself.
On a reboot, QEMU will reload its own BIOS, but use the migrated start
addresses, which does not work if the values differ.
Fix this by not relying on the migrated values anymore, but still
provide them during migration, so existing QEMUs continue to work.
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Cc: qemu-stable@nongnu.org
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
If bootindex is specified for a device, we need to IPL from
it. Currently it works for ccw devices, but not for SCSI. To be able to
IPL from the specific device, pc-bios needs to know its address.
For this reason we add special QEMU_SCSI IPL type into the IPLB
structure, that contains the scsi device address.
We enhance the ipl block with a currently qemu-only parameter block
that allows us to specify a concrete scsi device.
Signed-off-by: Alexander Yarygin <yarygin@linux.vnet.ibm.com>
Reviewed-by: Eric Farman <farman@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
It's a prerequisite that certain bits of MSR_IA32_FEATURE_CONTROL should
be set before some features (e.g. VMX and LMCE) can be used, which is
usually done by the firmware. This patch adds a fw_cfg file
"etc/msr_feature_control" which contains the advised value of
MSR_IA32_FEATURE_CONTROL and can be used by guest firmware (e.g. SeaBIOS).
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Haozhong Zhang <haozhong.zhang@intel.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
Considering that features are converted to global properties and
global properties are automatically applied to every new instance
of created CPU (at object_new() time), there is no point in
parsing cpu_model string every time a CPU created. So move
parsing outside CPU creation loop and do it only once.
Parsing also should be done before any CPU is created so that
features would affect the first CPU a well.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
Considering that features are converted to global properties and
global properties are automatically applied to every new instance
of created CPU (at object_new() time), there is no point in
parsing cpu_model string every time a CPU created. So move
parsing outside CPU creation loop and do it only once.
Parsing also should be done before any CPU is created so that
features would affect the first CPU a well.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
Currently CPUClass->parse_features() is used to parse -cpu
features string and set properties on created CPU instances.
But considering that features specified by -cpu apply to every
created CPU instance, it doesn't make sense to parse the same
features string for every CPU created. It also makes every target
that cares about parsing features string explicitly call
CPUClass->parse_features() parser, which gets in a way if we
consider using generic device_add for CPU hotplug as device_add
has not a clue about CPU specific hooks.
Turns out we can use global properties mechanism to set
properties on every created CPU instance for a given type. That
way it's possible to convert CPU features into a set of global
properties for CPU type specified by -cpu cpu_model and common
Device.device_post_init() will apply them to CPU of given type
automatically regardless whether it's manually created CPU or CPU
created with help of device_add.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
Use the new GlobalProperty.errp field to handle compat_props
errors.
Example output before this change:
(with an intentionally broken entry added to PC_COMPAT_1_3 just
for testing)
$ qemu-system-x86_64 -machine pc-1.3
qemu-system-x86_64: hw/core/qdev-properties.c:1091: qdev_prop_set_globals_for_type: Assertion `prop->user_provided' failed.
Aborted (core dumped)
After:
$ qemu-system-x86_64 -machine pc-1.3
Unexpected error in x86_cpuid_set_vendor() at /home/ehabkost/rh/proj/virt/qemu/target-i386/cpu.c:1688:
qemu-system-x86_64: can't apply global cpu.vendor=x: Property '.vendor' doesn't take value 'x'
Aborted (core dumped)
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
Move the compat_props handling to core machine code.
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
The new field will allow error handling to be configured by
qdev_prop_register_global() callers: &error_fatal and
&error_abort can be used to make QEMU exit or abort if any errors
are reported when applying the properties.
While doing it, change the error message from "global %s.%s=%s
ignored" to "can't apply global %s.%s=%s".
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
The function is just a helper to handle the -global options, it
can stay in vl.c like most qemu_opts_foreach() calls.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
qdev_prop_set_globals_for_type() stops applying global properties
on the first error. It is a leftover from when QEMU exited on any
error when applying global property. Commit 25f8dd9 changed the
fatal error to a warning, but neglected to drop the stopping.
Fix that.
For example, the following command-line will not set CPUID level
to 3, but will warn only about "x86_64-cpu.vendor" being ignored.
$ ./x86_64-softmmu/qemu-system-x86_64 \
-global x86_64-cpu.vendor=x \
-global x86_64-cpu.level=3
qemu-system-x86_64: Warning: global x86_64-cpu.vendor=x ignored: Property '.vendor' doesn't take value 'x'
Fix this by not returning from qdev_prop_set_globals_for_type()
on the first error.
Cc: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
In various Freescale SOCs, the GPT timers can be configured to select
its input clock.
Depending on the SOC the set of available input clocks may vary.
The actual single GPT definition was no good enough and because of it
booting the sabrelite board with a i.MX6DL device tree would fail
because of an incorrect input clock definition for the i.MX6DL SOC.
This patch fixes the i.MX6DL boot failure by adding the ability to
define a different set of input clocks depending on the considered SOC.
A different class has been defined for i.MX25, i.MX31 and i.MX6 each with
its specific set of input clocks.
The patch has been tested by booting KZM, i.MX25 PDK, i.MX6Q sabrelite
and i.MX6DL sabrelite.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Message-id: 1467325619-8374-1-git-send-email-jcd@tribudubois.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
[PMM: fixed spacing round '/' operator]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
These two are spot by Coverity 1357232 and 1357233.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1467684998-12076-1-git-send-email-zhaoshenglong@huawei.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
On Windows 'aux.*' is a reserved name and cannot be used for
filenames; see
https://msdn.microsoft.com/en-gb/library/windows/desktop/aa365247(v=vs.85).aspx
This prevents cloning the QEMU git repo on Windows:
C:\Java\sources\kvm> git clone https://github.com/qemu/qemu.git
Cloning into 'qemu'...
remote: Counting objects: 279563, done.
remote: Total 279563 (delta 0), reused 0 (delta 0), pack-reused 279563R
Receiving objects: 100% (279563/279563), 122.45 MiB | 3.52 MiB/s, done.
Resolving deltas: 100% (221942/221942), done.
Checking connectivity... done.
error: unable to create file hw/misc/aux.c (No such file or directory)
error: unable to create file include/hw/misc/aux.h (No such file or directory)
Checking out files: 100% (4795/4795), done.
fatal: unable to checkout working tree
warning: Clone succeeded, but checkout failed.
You can inspect what was checked out with 'git status'
and retry the checkout with 'git checkout -f HEAD'
(bug https://bugs.launchpad.net/bugs/1595240)
Rename the offending files for the benefit of Windows.
Reported-by: Алексей Курган <akurgan@yandex.ru>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Wei Huang <wei@redhat.com>
Tested-by: KONRAD Frederic <fred.konrad@greensocs.com>
Message-id: 1467377145-32385-1-git-send-email-peter.maydell@linaro.org
|
|
The last "ret = AUX_I2C_NACK;" is dead, because it is always overridden
by AUX_I2C_ACK. What really the code wants is to jump out of the switch
statement, and a "return" will not cut it because it would omit a debug
printf.
Change the logic so that we can break out of the while loop. For clarity,
hoist the bus->last_* assignments up, right after i2c_start_transfer.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
xlnx_dp_aux_push_tx_fifo takes an immediate uint8_t and a buffer length,
which must be 1 because that is how many uint8_t's fit in a uint8_t.
Sure enough, that is what xlnx_dp_write passes to it, but the function
is just weird. Therefore, make xlnx_dp_aux_push_tx_fifo look like
xlnx_dp_aux_push_rx_fifo, taking a pointer to the buffer.
Reported by Coverity.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
This patch add the capability of basic vhost net busy polling which is
supported by recent kernel. User could configure the maximum number of
us that could be spent on busy polling through a new property of tap
"poll-us".
Cc: Greg Kurz <groug@kaod.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
staging
spice and qxl bugfixes.
# gpg: Signature made Wed 06 Jul 2016 10:44:10 BST
# gpg: using RSA key 0x4CB6D8EED3E87138
# gpg: Good signature from "Gerd Hoffmann (work) <kraxel@redhat.com>"
# gpg: aka "Gerd Hoffmann <gerd@kraxel.org>"
# gpg: aka "Gerd Hoffmann (private) <kraxel@gmail.com>"
# Primary key fingerprint: A032 8CFF B93A 17A7 9901 FE7D 4CB6 D8EE D3E8 7138
* remotes/spice/tags/pull-spice-20160706-1:
virgl: pass whole GL scanout dimensions
spice: use the right head for multi-monitor
virgl: count the calls to gl_block
spice: avoid .set_mm_time on >= 0.12.6
qxl: fix surface migration
qxl: store memory region and offset instead of pointer for guest slots
qxl: factor out qxl_get_check_slot_offset
qxl: handle no updates in interface_update_area_complete
qxl: use uint64_t for vram size
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
staging
QAPI patches for 2016-07-06
# gpg: Signature made Wed 06 Jul 2016 10:00:51 BST
# gpg: using RSA key 0x3870B400EB918653
# gpg: Good signature from "Markus Armbruster <armbru@redhat.com>"
# gpg: aka "Markus Armbruster <armbru@pond.sub.org>"
# Primary key fingerprint: 354B C8B3 D7EB 2A6B 6867 4E5F 3870 B400 EB91 8653
* remotes/armbru/tags/pull-qapi-2016-07-06:
replay: Use new QAPI cloning
sockets: Use new QAPI cloning
qapi: Add new clone visitor
qapi: Add new visit_complete() function
tests: Factor out common code in qapi output tests
tests: Clean up test-string-output-visitor
qmp-output-visitor: Favor new visit_free() function
string-output-visitor: Favor new visit_free() function
qmp-input-visitor: Favor new visit_free() function
string-input-visitor: Favor new visit_free() function
opts-visitor: Favor new visit_free() function
qapi: Add new visit_free() function
qapi: Add parameter to visit_end_*
qemu-img: Don't leak errors when outputting JSON
qapi: Improve use of qmp/types.h
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Now that we have a polymorphic visit_free(), we no longer need
opts_visitor_cleanup(); which in turn means we no longer need
to return a subtype from opts_visitor_new() nor a public upcast
function.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1465490926-28625-6-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
|
|
Rather than making the dealloc visitor track of stack of pointers
remembered during visit_start_* in order to free them during
visit_end_*, it's a lot easier to just make all callers pass the
same pointer to visit_end_*. The generated code has access to the
same pointer, while all other users are doing virtual walks and
can pass NULL. The dealloc visitor is then greatly simplified.
All three visit_end_*() functions intentionally take a void**,
even though the visit_start_*() functions differ between void**,
GenericList**, and GenericAlternate**. This is done for several
reasons: when doing a virtual walk, passing NULL doesn't care
what the type is, but when doing a generated walk, we already
have to cast the caller's specific FOO* to call visit_start,
while using void** lets us use visit_end without a cast. Also,
an upcoming patch will add a clone visitor that wants to use
the same implementation for all three visit_end callbacks,
which is made easier if all three share the same signature.
For visitors with already track per-object state (the QMP visitors
via a stack, and the string visitors which do not allow nesting),
add an assertion that the caller is indeed passing the same
pointer to paired calls.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1465490926-28625-4-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
|
|
'qjson.h' is not a QObject subtype; include this file directly in
.c files that are using it, rather than abusing qmp/types.h for
that purpose.
Meanwhile, for files that include a list of individual QObject
subtypes, it's easier to just use qmp/types.h for that purpose.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <1465490926-28625-2-git-send-email-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
|
|
Spice client needs the whole GL texture dimension to be able to show a
scanout with a monitor offset (different than +0+0).
Furthermore, this fixes a crash when calling surface_{width,height}()
after dpy_gfx_replace_surface(con, NULL) was called in
virgl_cmd_set_scanout()
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 1465911849-30423-4-git-send-email-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
In virgl_cmd_resource_flush(), when several consoles are updated, it
needs to keep blocking until all spice gl draws are done. This fixes an
assert() in spice when using multiple monitors with virgl.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-id: 1465911849-30423-2-git-send-email-marcandre.lureau@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Spice deprecated this callback in 0.12.6.
It's not a problem yet, but it will cause Clang to fail in a -Werror
build due to the deprecated tag.
Signed-off-by: John Snow <jsnow@redhat.com>
Message-id: 1467240095-12507-2-git-send-email-jsnow@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Create a helper function qxl_dirty_one_surface() to mark a single qxl
surface as dirty. Use the new qxl_get_check_slot_offset function and
lookup the memory region from the slot instead of assuming the surface
is stored in vram.
Use the new helper function in qxl_dirty_surfaces, for both primary and
off-screen surfaces. For off-screen surfaces this is no functional
change. For primary surfaces this will dirty only the memory actually
used instead of the whole surface0 region. It will also work correctly
in case the guest places the primary surface in vram instead of the
surface0 region (linux kms driver does that).
https://bugzilla.redhat.com/show_bug.cgi?id=1235732
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1466597244-5938-3-git-send-email-kraxel@redhat.com
|
|
Store MemoryRegion and offset instead of a pointer for each qxl memory
slot, so we can easily figure in which memory region an qxl object
stored.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 1466597244-5938-2-git-send-email-kraxel@redhat.com
|
