aboutsummaryrefslogtreecommitdiff
path: root/hw
AgeCommit message (Collapse)Author
2014-01-08hw: arm_gic: Introduce gic_set_priority functionChristoffer Dall
To make the code slightly cleaner to look at and make the save/restore code easier to understand, introduce this function to set the priority of interrupts. Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org> Message-id: 1387606179-22709-3-git-send-email-christoffer.dall@linaro.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2014-01-08arm_gic: Rename GIC_X_TRIGGER to GIC_X_EDGE_TRIGGERChristoffer Dall
TRIGGER can really mean mean anything (e.g. was it triggered, is it level-triggered, is it edge-triggered, etc.). Rename to EDGE_TRIGGER to make the code comprehensible without looking up the data structure. Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org> Message-id: 1387606179-22709-2-git-send-email-christoffer.dall@linaro.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2014-01-08arm/xilinx_zynq: Always instantiate the GEMsPeter Crosthwaite
Don't conditionalise GEM instantiation on networking attachments. The device should always be present even if not attached to a network. This allows for probing of the device by expectant guests (such as OS's). This is needed because sysbus (or AXI in Xilinx's real hw case) is not self identifying so the guest has no dynamic way of detecting device absence. Also allows for testing of the GEM in loopback mode with -net none. Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Message-id: 55649779a68ee3ff54b24c339b6fdbdccd1f0ed7.1388800598.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2014-01-08char/cadence_uart: Implement Tx flow controlPeter Crosthwaite
If the UART back-end blocks, buffer in the Tx FIFO to try again later. This stops the IO-thread busy waiting on char back-ends (which causes all sorts of performance problems). Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: 4bea048b3ab38425701d82ccc1ab92545c26b79c.1388626249.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2014-01-08char/cadence_uart: Delete redundant rx rst logicPeter Crosthwaite
uart_rx_reset() called immediately above already does this. Remove. Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: 05e30826496cf2579084ed801ac0b2c0d0a3071f.1388626249.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2014-01-08char/cadence_uart: Use the TX fifo for transmissionPeter Crosthwaite
Populate the TxFIFO with the Tx data before sending. Prepares support for proper Tx flow control implementation. Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: bdf7f8af2ef02839bea18665701bc2612f7baa6f.1388626249.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2014-01-08char/cadence_uart: Fix can_receive logicPeter Crosthwaite
The can_receive logic was only taking into account the RxFIFO occupancy. RxFIFO population is only used for the echo and normal modes however. Improve the logic to correctly return the true number of receivable characters based on the current mode: Normal mode: RxFIFO vacancy. Remote loopback: TxFIFO vacancy. Echo mode: The min of the TxFIFO and RxFIFO vacancies. Local Loopback: Return non-zero (to implement droppage) Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: 36a58440c9ca5080151e95765c2c81342de8a8df.1388626249.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2014-01-08char/cadence_uart: Remove TX timer & add TX FIFO statePeter Crosthwaite
This tx timer implementation is flawed. Despite the controller attempting to time the guest visable assertion of the TX-empty status bit (and corresponding interrupt) the controller is still transmitting characters instantaneously. There is also no sense of multiple character delay. The only side effect of this timer is assertion of tx-empty status. So just remove the timer completely and hold tx-empty as permanently asserted (its reset status). This matches the actual behaviour of instantaneous transmission. While we are VMSD version bumping, add the tx_fifo as device state to prepare for upcomming TxFIFO flow control. Implement the interrupt generation logic for the TxFIFO occupancy. Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: 7a208a7eb8d79d6429fe28b1396c3104371807b2.1388626249.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2014-01-08char/cadence_uart: Define Missing SR/ISR fieldsPeter Crosthwaite
Some (interrupt) status register bits relating to the TxFIFO path were not defined. Define them. This prepares support for proper Tx data path flow control. Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: 2068b963f0af8cc834c353944e9fa816d950b163.1388626249.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2014-01-08char/cadence_uart: Simplify status generationPeter Crosthwaite
The status register bits are always pure functions of other device state. Move the generation of these bits to the update_status() function to simplify. Makes developing much easier as theres now no need to recheck status bits on all the changes to rx/tx fifo state. Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: 321994929f789096975104f99c55732774be4cae.1388626249.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2014-01-08char/cadence_uart: s/r_fifo/rx_fifoPeter Crosthwaite
Rename this field to match the many other uses of "rx". Xilinx docmentation (UG585) also refers to this as "RxFIFO". Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: 7386d7cee0ea175f7e53ed5ff045265528d34e32.1388626249.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2014-01-08char/cadence_uart: Fix reset.Peter Crosthwaite
Don't reset the uart as an init step. Register the reset function as a proper reset fn instead. Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: d82cd2e65e5a6f8b6deeecb6cced61f0bf3f8c89.1388626249.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2014-01-08char/cadence_uart: Add missing uart_update_statePeter Crosthwaite
This should be rechecked on bus write accesses as such accesses may change the underlying state that generates the interrupt. Particular relevant for when the guest touches the interrupt status or mask. Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: 1c250cd61b7b8de492fbc8b79b8370958a56d83b.1388626249.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2014-01-08char/cadence_uart: Mark struct fields as public/privatePeter Crosthwaite
As per current QOM conventions. Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: a1e31bd62e9709ffb9b3efc6c120f83f30b7a660.1388626249.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-20spapr: limit numa memory regions by ram sizePaul Mackerras
This makes sure that all NUMA memory blocks reside within RAM or have zero length. Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com> Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Alexander Graf <agraf@suse.de>
2013-12-20spapr: make sure RMA is in first mode of first memory nodeAlexey Kardashevskiy
The SPAPR specification says that the RMA starts at the LPAR's logical address 0 and is the first logical memory block reported in the LPAR’s device tree. So SLOF only maps the first block and that block needs to span the full RMA. This makes sure that the RMA area is where SLOF expects it. Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com> Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Alexander Graf <agraf@suse.de>
2013-12-20device_tree: s/qemu_devtree/qemu_fdt globallyPeter Crosthwaite
The qemu_devtree API is a wrapper around the fdt_ set of APIs. Rename accordingly. Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> [agraf: also convert hw/arm/virt.c] Signed-off-by: Alexander Graf <agraf@suse.de>
2013-12-20roms: Flush icache when writing roms to guest memoryAlexander Graf
We use the rom infrastructure to write firmware and/or initial kernel blobs into guest address space. So we're basically emulating the cache off phase on very early system bootup. That phase is usually responsible for clearing the instruction cache for anything it writes into cachable memory, to ensure that after reboot we don't happen to execute stale bits from the instruction cache. So we need to invalidate the icache every time we write a rom into guest address space. We do not need to do this for every DMA since the guest expects it has to flush the icache manually in that case. This fixes random reboot issues on e5500 (booke ppc) for me. Signed-off-by: Alexander Graf <agraf@suse.de>
2013-12-20spapr: tie spapr-nvram to -pflashPaolo Bonzini
spapr-nvram's drive property is currently connected to a non-existent "-machine nvram=<drivename>" option. Instead, tie it to -pflash like other non-volatile RAM devices. This provides the following possibilities for adding a backend for the sPAPR non-volatile RAM: * -pflash filename * -drive if=pflash,file=filename,format=raw,... * -drive if=none,file=filename,format=raw,id=foo,... -global spapr-nvram.drive=foo Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Alexander Graf <agraf@suse.de>
2013-12-20PPC: Use default pci bus name for grackle and heathrowAlexander Graf
There's no good reason to call our bus "pci" rather than let the default bus name take over ("pci.0"). The big downside to calling it different from anyone else is that tools that pass -device get confused. They are looking for a bus "pci.0" rather than "pci". To make life easier for everyone, let's just drop the name override. Signed-off-by: Alexander Graf <agraf@suse.de>
2013-12-20spapr-rtas: add ibm, (get|set)-system-parameterAlexey Kardashevskiy
This adds very basic handlers for ibm,get-system-parameter and ibm,set-system-parameter RTAS calls. The only parameter handled at the moment is "platform-processor-diagnostics-run-mode" which is always disabled and does not support changing. This is expected to make "ppc64_cpu --run-mode=1" happy. Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> [agraf: s/papameter/parameter/g] Signed-off-by: Alexander Graf <agraf@suse.de>
2013-12-20spapr-rtas: replace return code constants with macrosAlexey Kardashevskiy
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Alexander Graf <agraf@suse.de>
2013-12-17hw/arm: add cubieboard supportliguang
Signed-off-by: liguang <lig.fnst@cn.fujitsu.com> Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: 1387159292-10436-6-git-send-email-lig.fnst@cn.fujitsu.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-17hw/arm: add allwinner a10 SoC supportliguang
Signed-off-by: liguang <lig.fnst@cn.fujitsu.com> Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: 1387159292-10436-5-git-send-email-lig.fnst@cn.fujitsu.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-17hw/intc: add allwinner A10 interrupt controllerliguang
Signed-off-by: liguang <lig.fnst@cn.fujitsu.com> Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Message-id: 1387159292-10436-4-git-send-email-lig.fnst@cn.fujitsu.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-17hw/timer: add allwinner a10 timerliguang
Signed-off-by: liguang <lig.fnst@cn.fujitsu.com> Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: 1387159292-10436-3-git-send-email-lig.fnst@cn.fujitsu.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-17hw/arm/digic: add NOR ROM supportAntony Pavlov
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Message-id: 1387188908-754-6-git-send-email-antonynpavlov@gmail.com [PMM: don't try to load ROM blob if qtest_enabled()] Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-17hw/arm/digic: add UART supportAntony Pavlov
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: 1387188908-754-5-git-send-email-antonynpavlov@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-17hw/arm/digic: add timer supportAntony Pavlov
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: 1387188908-754-4-git-send-email-antonynpavlov@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-17hw/arm/digic: prepare DIGIC-based boards supportAntony Pavlov
Also this patch adds initial support for Canon PowerShot A1100 IS compact camera. Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Message-id: 1387188908-754-3-git-send-email-antonynpavlov@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-17hw/arm: add very initial support for Canon DIGIC SoCAntony Pavlov
DIGIC is Canon Inc.'s name for a family of SoC for digital cameras and camcorders. There is no publicly available specification for DIGIC chips. All information about DIGIC chip internals is based on reverse engineering efforts made by CHDK (http://chdk.wikia.com) and Magic Lantern (http://www.magiclantern.fm) projects contributors. Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com> Reviewed-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: 1387188908-754-2-git-send-email-antonynpavlov@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-17hw/arm/boot: Add boot support for AArch64 processorMian M. Hamayun
This commit adds support for booting a single AArch64 CPU by setting appropriate registers. The bootloader includes placeholders for Board-ID that are used to implement uniform indexing across different bootloaders. Signed-off-by: Mian M. Hamayun <m.hamayun@virtualopensystems.com> Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Message-id: 1385645602-18662-7-git-send-email-peter.maydell@linaro.org [PMM: * updated to use ARMInsnFixup style bootloader fragments * dropped virt.c additions * use runtime checks for "is this an AArch64 core" rather than ifdefs * drop some unnecessary setting of registers in reset hook ] Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
2013-12-17hw/arm/boot: Allow easier swapping in of different loader codePeter Maydell
For AArch64 we will obviously require a different set of primary and secondary boot loader code fragments. However currently we hardcode the offsets into the loader code where we must write the entrypoint and other data into arm_load_kernel(). This makes it hard to substitute a different loader fragment, so switch to a more flexible scheme where instead of a raw array of instructions we use an array of (instruction, fixup-type) pairs that indicate which words need special action or data written into them. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Message-id: 1385645602-18662-6-git-send-email-peter.maydell@linaro.org Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org> Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
2013-12-17arm/highbank.c: Fix MPCore periphbase namePeter Crosthwaite
GIC_BASE_ADDR is not the base address of the GIC. Its clear from the code that this is the base address of the MPCore. Rename to MPCORE_PERIPHBASE accordingly. Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Message-id: 90798bd3507205c16238b8b19a1a58c5437cf7ca.1387160489.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-17arm/xilinx_zynq: Implement CBAR initialisationPeter Crosthwaite
Fix the CBAR initialisation by using the newly defined static property. Zynq will now correctly init the CBAR to the SCU base address. Needed to boot Linux on the xilinx_zynq machine model. Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Message-id: 8db7d57ebe5418fed397fcc86ea719f98446c178.1387160489.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-17arm/xilinx_zynq: Use object_new() rather than cpu_arm_init()Peter Crosthwaite
To allow the machine model to set device properties before CPU realization. Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Message-id: e57658b4506b26ab6b6fadbe6d7827f669f51895.1387160489.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-17arm/highbank: Fix CBAR initialisationPeter Crosthwaite
Fix the CBAR initialisation by using the newly defined static property. CBAR is now set before realization, so the intended value is now actually used. So I have kind of tested this. I booted an ARM kernel on Highbank with the stock Highbank DTB. It doesn't boot (and I will be doing something wrong), but before this patch I got this: ------------[ cut here ]------------ WARNING: CPU: 0 PID: 0 at /workspaces/pcrost/public/linux2.git/arch/arm/mm/ioremap.c:301 __arm_ioremap_pfn_caller+0x180/0x198() CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 3.13.0-rc1-next-20131126-dirty #2 [<c0015164>] (unwind_backtrace) from [<c00118c0>] (show_stack+0x10/0x14) [<c00118c0>] (show_stack) from [<c02bd5fc>] (dump_stack+0x78/0x90) [<c02bd5fc>] (dump_stack) from [<c001f110>] (warn_slowpath_common+0x68/0x84) [<c001f110>] (warn_slowpath_common) from [<c001f1f4>] (warn_slowpath_null+0x1c/0x24) [<c001f1f4>] (warn_slowpath_null) from [<c0017c6c>] (__arm_ioremap_pfn_caller+0x180/0x198) [<c0017c6c>] (__arm_ioremap_pfn_caller) from [<c0017cd8>] (__arm_ioremap_caller+0x54/0x5c) [<c0017cd8>] (__arm_ioremap_caller) from [<c0017d10>] (__arm_ioremap+0x18/0x1c) [<c0017d10>] (__arm_ioremap) from [<c03913c0>] (highbank_init_irq+0x34/0x8c) [<c03913c0>] (highbank_init_irq) from [<c038c228>] (init_IRQ+0x28/0x2c) [<c038c228>] (init_IRQ) from [<c03899ec>] (start_kernel+0x234/0x398) [<c03899ec>] (start_kernel) from [<00008074>] (0x8074) ---[ end trace 3406ff24bd97382f ]--- Which disappears with this patch. Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Message-id: fedec366aaa512d75093635f523d1dbcb3358361.1387160489.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-17arm/highbank: Use object_new() rather than cpu_arm_init()Peter Crosthwaite
To allow the machine model to set device properties before CPU realization. Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Message-id: 8c671e500390c8be0cc363e887e32867d1d1b0d2.1387160489.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-17Fix NOR flash device ID readingRoy Franz
Fix NOR flash manufacturer and device ID reading. This now properly takes into account device widths and device max widths as required. The reading of these IDs uses the same max_width dependent addressing as CFI queries. The old code remains for chips that don't specify a device width, as the new code relies on a device width being set in order to properly operate. The existing code seems very broken. Only ident0 and ident1 are used in the new code, as other fields relate to the lock state of blocks in flash. The VExpress flash configuration has been updated to match the new code, as the existing definition was 'wrong' in order to return the expected results with the broken device ID code. Signed-off-by: Roy Franz <roy.franz@linaro.org> Message-id: 1386279359-32286-8-git-send-email-roy.franz@linaro.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-17Fix CFI query responses for NOR flashRoy Franz
This change fixes the CFI query responses to handle NOR device widths that are different from the bank width. Support is also added for multi-width devices in a x8 configuration. This is typically x8/x16 devices, but the CFI specification mentions x8/x32 devices so those should be supported as well if they exist. The query response data is now replicated per-device in the bank, and is adjusted for x16 or x32 parts configured in x8 mode. The existing code is left in place for boards that have not been updated to specify an explicit device_width. The VExpress board has been updated in an earlier patch in this series so this is the only board currently affected. Signed-off-by: Roy Franz <roy.franz@linaro.org> Message-id: 1386279359-32286-7-git-send-email-roy.franz@linaro.org [PMM: fixed a few formatting nits] Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-17Add max device width parameter for NOR devicesRoy Franz
For handling CFI and device ID reads, we need to not only know the width that a NOR flash device is configured for, but also its maximum width. The maximum width addressing mode is used for multi-width parts no matter which width they are configured for. The most common case is x16 parts that also support x8 mode. When configured for x8 operation these devices respond to CFI and device ID requests differently than native x8 NOR parts. Signed-off-by: Roy Franz <roy.franz@linaro.org> Message-id: 1386279359-32286-6-git-send-email-roy.franz@linaro.org [PMM: Added comment explaining the semantics of width vs device-width vs max-device-width] Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-17Set proper device-width for vexpress flashRoy Franz
Create vexpress specific pflash registration function which properly configures the device-width of 16 bits (2 bytes) for the NOR flash on the vexpress platform. This change is required for buffered flash writes to work properly. Signed-off-by: Roy Franz <roy.franz@linaro.org> Message-id: 1386279359-32286-5-git-send-email-roy.franz@linaro.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-17return status for each NOR flash deviceRoy Franz
Now that we know how wide each flash device that makes up the bank is, return status for each device in the bank. Leave existing code that treats 32 bit wide banks as composed of two 16 bit devices as otherwise we may break configurations that do not set the device_width propery. Signed-off-by: Roy Franz <roy.franz@linaro.org> Message-id: 1386279359-32286-4-git-send-email-roy.franz@linaro.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-17Add device-width property to pflash_cfi01Roy Franz
The width of the devices that make up the flash interface is required to mask certain commands, in particular the write length for buffered writes. This length will be presented to each device on the interface by the program writing the flash, and the flash emulation code needs to be able to determine the length of the write as recieved by each flash device. The device-width defaults to the bank width which should maintain existing behavior for platforms that don't need this change. This change is required to support buffered writes on the vexpress platform that has a 32 bit flash interface with 2 16 bit devices on it. Signed-off-by: Roy Franz <roy.franz@linaro.org> Message-id: 1386279359-32286-3-git-send-email-roy.franz@linaro.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-17rename pflash_t member width to bank_widthRoy Franz
Rename the 'width' member of the pflash_t structure in preparation for adding a bank_width member. Signed-off-by: Roy Franz <roy.franz@linaro.org> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Message-id: 1386279359-32286-2-git-send-email-roy.franz@linaro.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2013-12-16spice: stop server for qxl hard resetGerd Hoffmann
Hard reset can happen at any time. We should be able to put qxl into a known-good state no matter what. Stop spice server thread for reset so it can't be confused by fetching stale commands lingering around in the rings while we reset is ongoing. Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
2013-12-13Merge remote-tracking branch 'bonzini/virtio' into stagingAnthony Liguori
# By Andreas Färber (18) and Paolo Bonzini (12) # Via Paolo Bonzini * bonzini/virtio: (30 commits) virtio: Convert exit to unrealize virtio: Complete converting VirtioDevice to QOM realize virtio-scsi: Convert to QOM realize virtio-rng: Convert to QOM realize virtio-balloon: Convert to QOM realize virtio-net: Convert to QOM realize virtio-serial: Convert to QOM realize virtio-blk: Convert to QOM realize virtio-9p: Convert to QOM realize virtio: Start converting VirtioDevice to QOM realize virtio-scsi: QOM realize preparations virtio-rng: QOM realize preparations virtio-balloon: QOM realize preparations virtio-net: QOM realize preparations virtio-serial: QOM realize preparations virtio-blk: QOM realize preparations virtio-9p: QOM realize preparations virtio-blk-dataplane: Improve error reporting virtio-pci: add device_unplugged callback virtio-rng: switch exit callback to VirtioDeviceClass ...
2013-12-13Merge remote-tracking branch 'mst/tags/for_anthony' into stagingAnthony Liguori
acpi.pci,pc,memory core fixes Most notably this includes changes to exec to support full 64 bit addresses. This also flushes out patches that got queued during 1.7 freeze. There are new tests, and a bunch of bug fixes all over the place. There are also some changes mostly useful for downstreams. I'm also listing myself as pc co-maintainer. I'm doing this reluctantly, but this seems to be necessary to make sure patches are not lost or delayed too much, and posting the MAINTAINERS patch did not seem to make anyone else volunteer. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> # gpg: Signature made Wed 11 Dec 2013 10:21:51 AM PST using RSA key ID D28D5469 # gpg: Can't check signature: public key not found # By Michael S. Tsirkin (14) and others # Via Michael S. Tsirkin * mst/tags/for_anthony: (28 commits) pc: use macro for HPET type hpet: fix build with CONFIG_HPET off acpi unit-test: adjust the test data structure for better handling acpi unit-test: load and check facs table exec: separate sections and nodes per address space memory.c: bugfix - ref counting mismatch in memory_region_find hpet: enable to entitle more irq pins for hpet hpet: inverse polarity when pin above ISA_NUM_IRQS pci: fix pci bridge fw path ACPI DSDT: Make control method `IQCR` serialized acpi: strip compiler info in built-in DSDT acpi unit-test: verify signature and checksum smbios: Set system manufacturer, product & version by default exec: reduce L2_PAGE_SIZE exec: make address spaces 64-bit wide exec: memory radix tree page level compression exec: pass hw address to phys_page_find exec: extend skip field to 6 bit, page entry to 32 bit exec: replace leaf with skip split definitions for exec.c and translate-all.c radix trees ... Message-id: cover.1386786228.git.mst@redhat.com Signed-off-by: Anthony Liguori <aliguori@amazon.com>
2013-12-13Merge remote-tracking branch 'bonzini/scsi-next' into stagingAnthony Liguori
# By Paolo Bonzini (4) and Peter Lieven (1) # Via Paolo Bonzini * bonzini/scsi-next: help: add id suboption to -iscsi scsi-disk: fix WRITE SAME with large non-zero payload block/iscsi: introduce bdrv_co_{readv, writev, flush_to_disk} scsi-disk: fix VERIFY emulation scsi-bus: fix transfer length and direction for VERIFY command Message-id: 1386594157-17535-1-git-send-email-pbonzini@redhat.com Signed-off-by: Anthony Liguori <aliguori@amazon.com>
2013-12-11pc: use macro for HPET typeMichael S. Tsirkin
avoid hard-coding strings Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
generated by cgit v1.2.3 (git 2.26.2) at 2025-01-28 17:33:10 +0000