Age | Commit message (Collapse) | Author |
|
The PL061 GPIO does not itself include pullup or pulldown resistors
to set the value of a GPIO line treated as an output when it is
configured as an input (ie when the PL061 itself is not driving it).
In real hardware it is up to the board to add suitable pullups or
pulldowns. Currently our implementation hardwires this to "outputs
pulled high", which is correct for some boards (eg the realview ones:
see figure 3-29 in the "RealView Platform Baseboard for ARM926EJ-S
User Guide" DUI0224I), but wrong for others.
In particular, the wiring in the 'virt' board and the gpio-pwr device
assumes that wires should be pulled low, because otherwise the
pull-to-high will trigger a shutdown or reset action. (The only
reason this doesn't happen immediately on startup is due to another
bug in the PL061, where we don't assert the GPIOs to the correct
value on reset, but will do so as soon as the guest touches a
register and pl061_update() gets called.)
Add properties to the pl061 so the board can configure whether it
wants GPIO lines to have pullup, pulldown, or neither.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
|
|
The Luminary variant of the PL061 has registers GPIOPUR and GPIOPDR
which lets the guest configure whether the GPIO lines are pull-up,
pull-down, or truly floating. Instead of assuming all lines are pulled
high, honour the PUR and PDR registers.
For the plain PL061, continue to assume that lines have an external
pull-up resistor, as we did before.
The stellaris board actually relies on this behaviour -- the CD line
of the ssd0323 display device is connected to GPIO output C7, and it
is only because of a different bug which we're about to fix that we
weren't incorrectly driving this line high on reset and putting the
ssd0323 into data mode.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
|
|
Add a comment documenting the "QEMU interface" of this device:
which MMIO regions, IRQ lines, GPIO lines, etc it exposes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
|
|
Add tracepoints for reads and writes to the PL061 registers. This requires
restructuring pl061_read() to only return after the tracepoint, rather
than having lots of early-returns.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
|
|
Currently the pl061_read() and pl061_write() functions handle offsets
using a combination of three if() statements and a switch(). Clean
this up to use just a switch, using case ranges.
This requires that instead of catching accesses to the luminary-only
registers on a stock PL061 via a check on s->rsvd_start we use
an "is this luminary?" check in the cases for each luminary-only
register.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
|
|
Convert the use of the DPRINTF debug macro in the PL061 model to
use tracepoints.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
|
|
icv_eoir_write() and icv_dir_write() ignore invalid virtual IRQ numbers
(like LPIs). The issue is that these functions check against the number
of implemented IRQs (QEMU's default is num_irq=288) which can be lower
than the maximum virtual IRQ number (1020 - 1). The consequence is that
if a hypervisor creates an LR for an IRQ between 288 and 1020, then the
guest is unable to deactivate the resulting IRQ. Note that other
functions that deal with large IRQ numbers, like icv_iar_read, check
against 1020 and not against num_irq.
Fix the checks by using GICV3_MAXIRQ (1020) instead of the number of
implemented IRQs.
Signed-off-by: Ricardo Koller <ricarkol@google.com>
Message-id: 20210702233701.3369-1-ricarkol@google.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
This is a Cortex-M3 based machine. Information can be found at:
https://www.st.com/en/evaluation-tools/stm32vldiscovery.html
Signed-off-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210617165647.2575955-3-erdnaxe@crans.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
This SoC is similar to stm32f205 SoC.
This will be used by the STM32VLDISCOVERY to create a machine.
Signed-off-by: Alexandre Iooss <erdnaxe@crans.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20210617165647.2575955-2-erdnaxe@crans.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
pc,pci,virtio: bugfixes, improvements
vhost-user-rng support.
Fixes all over the place.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
# gpg: Signature made Wed 07 Jul 2021 14:29:30 BST
# gpg: using RSA key 5D09FD0871C8F85B94CA8A0D281F0DB8D28D5469
# gpg: issuer "mst@redhat.com"
# gpg: Good signature from "Michael S. Tsirkin <mst@kernel.org>" [full]
# gpg: aka "Michael S. Tsirkin <mst@redhat.com>" [full]
# Primary key fingerprint: 0270 606B 6F3C DF3D 0B17 0970 C350 3912 AFBE 8E67
# Subkey fingerprint: 5D09 FD08 71C8 F85B 94CA 8A0D 281F 0DB8 D28D 5469
* remotes/mst/tags/for_upstream:
MAINTAINERS: Add maintainer for vhost-user RNG implementation
docs: add slot when adding new PCIe root port
acpi/ged: fix reset cause
tests: acpi: pc: update expected DSDT blobs
acpi: pc: revert back to v5.2 PCI slot enumeration
tests: acpi: prepare for changing DSDT tables
migration: failover: reset partially_hotplugged
virtio-pci: Changed return values for "notify", "device" and "isr" read.
virtio-pci: Added check for virtio device in PCI config cbs.
virtio-pci: Added check for virtio device presence in mm callbacks.
hw/pci-host/q35: Ignore write of reserved PCIEXBAR LENGTH field
virtio: Clarify MR transaction optimization
virtio: disable ioeventfd for record/replay
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
dev->max_queues was never initialised for backends that don't support
VHOST_USER_PROTOCOL_F_MQ, so it would use 0 as the maximum number of
queues to check against and consequently fail for any such backend.
Set it to 1 if the backend doesn't have multiqueue support.
Fixes: c90bd505a3e8210c23d69fecab9ee6f56ec4a161
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-Id: <20210705171429.29286-1-kwolf@redhat.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
If KVM_CAP_RPT_INVALIDATE KVM capability is enabled, then
- indicate the availability of H_RPT_INVALIDATE hcall to the guest via
ibm,hypertas-functions property.
- Enable the hcall
Both the above are done only if the new sPAPR machine capability
cap-rpt-invalidate is set.
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Message-Id: <20210706112440.1449562-3-bharata@linux.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This addresses the comments from v22.
The functional changes are (the VOF ones need retesting with Pegasos2):
(VOF) setprop will start failing if the machine class callback
did not handle it;
(VOF) unit addresses are lowered in path_offset();
(SPAPR) /chosen/bootargs is initialized from kernel_cmdline if
the client did not change it.
Fixes: 5c991e5d4378 ("spapr: Implement Open Firmware client interface")
Cc: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20210708065625.548396-1-aik@ozlabs.ru>
Tested-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Linux uses RTAS functions to access PCI devices so we need to provide
these with VOF. Implement some of the most important functions to
allow booting Linux with VOF. With this the board is now usable
without a binary ROM image and we can enable it by default as other
boards.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20210708215113.B3F747456E3@zero.eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This is obviously intended to be a mask, not a logical operation.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The pegasos2 board comes with an Open Firmware compliant ROM based on
SmartFirmware but it has some changes that are not open source
therefore the ROM binary cannot be included in QEMU. Guests running on
the board however depend on services provided by the firmware. The
Virtual Open Firmware recently added to QEMU implements a minimal set
of these services to allow some guests to boot without the original
firmware. This patch adds VOF as the default firmware for pegasos2
which allows booting Linux and MorphOS via -kernel option while a ROM
image can still be used with -bios for guests that don't run with VOF.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <1d6ed6f290c5c1f0b5a1e1c51cf1151452d70d9a.1624811233.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
There are several new L1D cache flush bits added to the hcall which reflect
hardware security features for speculative cache access issues.
These behaviours are now being specified as negative in order to simplify
patched kernel compatibility with older firmware (a new problem found in
existing systems would automatically be vulnerable).
[dwg: Technically this changes behaviour for existing machine types.
After discussion with Nick, we've determined this is safe, because
the worst that will happen if a guest gets the wrong information due
to a migration is that it will perform some unnecessary workarounds,
but will remain correct and secure (well, as secure as it was going
to be anyway). In addition the change only affects cap-cfpc=safe
which is not enabled by default, and in fact is not possible to set
on any current hardware (though it's expected it will be possible on
POWER10)]
Signed-off-by: Nicholas Piggin <npiggin@gmail.com>
Message-Id: <20210615044107.1481608-1-npiggin@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Add own machine state structure which will be used to store state
needed for firmware emulation.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <7f6d5fbf4f70c64dba001483174a2921dd616ecd.1624811233.git.balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The PAPR platform describes an OS environment that's presented by
a combination of a hypervisor and firmware. The features it specifies
require collaboration between the firmware and the hypervisor.
Since the beginning, the runtime component of the firmware (RTAS) has
been implemented as a 20 byte shim which simply forwards it to
a hypercall implemented in qemu. The boot time firmware component is
SLOF - but a build that's specific to qemu, and has always needed to be
updated in sync with it. Even though we've managed to limit the amount
of runtime communication we need between qemu and SLOF, there's some,
and it has become increasingly awkward to handle as we've implemented
new features.
This implements a boot time OF client interface (CI) which is
enabled by a new "x-vof" pseries machine option (stands for "Virtual Open
Firmware). When enabled, QEMU implements the custom H_OF_CLIENT hcall
which implements Open Firmware Client Interface (OF CI). This allows
using a smaller stateless firmware which does not have to manage
the device tree.
The new "vof.bin" firmware image is included with source code under
pc-bios/. It also includes RTAS blob.
This implements a handful of CI methods just to get -kernel/-initrd
working. In particular, this implements the device tree fetching and
simple memory allocator - "claim" (an OF CI memory allocator) and updates
"/memory@0/available" to report the client about available memory.
This implements changing some device tree properties which we know how
to deal with, the rest is ignored. To allow changes, this skips
fdt_pack() when x-vof=on as not packing the blob leaves some room for
appending.
In absence of SLOF, this assigns phandles to device tree nodes to make
device tree traversing work.
When x-vof=on, this adds "/chosen" every time QEMU (re)builds a tree.
This adds basic instances support which are managed by a hash map
ihandle -> [phandle].
Before the guest started, the used memory is:
0..e60 - the initial firmware
8000..10000 - stack
400000.. - kernel
3ea0000.. - initramdisk
This OF CI does not implement "interpret".
Unlike SLOF, this does not format uninitialized nvram. Instead, this
includes a disk image with pre-formatted nvram.
With this basic support, this can only boot into kernel directly.
However this is just enough for the petitboot kernel and initradmdisk to
boot from any possible source. Note this requires reasonably recent guest
kernel with:
https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=df5be5be8735
The immediate benefit is much faster booting time which especially
crucial with fully emulated early CPU bring up environments. Also this
may come handy when/if GRUB-in-the-userspace sees light of the day.
This separates VOF and sPAPR in a hope that VOF bits may be reused by
other POWERPC boards which do not support pSeries.
This assumes potential support for booting from QEMU backends
such as blockdev or netdev without devices/drivers used.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20210625055155.2252896-1-aik@ozlabs.ru>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
[dwg: Adjusted some includes which broke compile in some more obscure
compilation setups]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
QEMU reserves space for RTAS via /rtas/rtas-size which tells the client
how much space the RTAS requires to work which includes the RTAS binary
blob implementing RTAS runtime. Because pseries supports FWNMI which
requires plenty of space, QEMU reserves more than 2KB which is
enough for the RTAS blob as it is just 20 bytes (under QEMU).
Since FWNMI reset delivery was added, RTAS_SIZE macro is not used anymore.
This replaces RTAS_SIZE with RTAS_MIN_SIZE and uses it in
the /rtas/rtas-size calculation to account for the RTAS blob.
Fixes: 0e236d347790 ("ppc/spapr: Implement FWNMI System Reset delivery")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Message-Id: <20210622070336.1463250-1-aik@ozlabs.ru>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
'remotes/stefanha-gitlab/tags/block-pull-request' into staging
Pull request
# gpg: Signature made Thu 08 Jul 2021 14:11:37 BST
# gpg: using RSA key 8695A8BFD3F97CDAAC35775A9CA4ABB381AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>" [full]
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>" [full]
# Primary key fingerprint: 8695 A8BF D3F9 7CDA AC35 775A 9CA4 ABB3 81AB 73C8
* remotes/stefanha-gitlab/tags/block-pull-request:
block/io: Merge discard request alignments
block: Add backend_defaults property
block/file-posix: Optimize for macOS
util/async: print leaked BH name when AioContext finalizes
util/async: add a human-readable name to BHs for debugging
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
We support coordinated discarding of RAM using the RamDiscardManager for
the VFIO_TYPE1 iommus. Let's unlock support for coordinated discards,
keeping uncoordinated discards (e.g., via virtio-balloon) disabled if
possible.
This unlocks virtio-mem + vfio on x86-64. Note that vfio used via "nvme://"
by the block layer has to be implemented/unlocked separately. For now,
virtio-mem only supports x86-64; we don't restrict RamDiscardManager to
x86-64, though: arm64 and s390x are supposed to work as well, and we'll
test once unlocking virtio-mem support. The spapr IOMMUs will need special
care, to be tackled later, e.g.., once supporting virtio-mem.
Note: The block size of a virtio-mem device has to be set to sane sizes,
depending on the maximum hotplug size - to not run out of vfio mappings.
The default virtio-mem block size is usually in the range of a couple of
MBs. The maximum number of mapping is 64k, shared with other users.
Assume you want to hotplug 256GB using virtio-mem - the block size would
have to be set to at least 8 MiB (resulting in 32768 separate mappings).
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Auger Eric <eric.auger@redhat.com>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Cc: teawater <teawaterz@linux.alibaba.com>
Cc: Marek Kedzierski <mkedzier@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210413095531.25603-14-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
We implement the RamDiscardManager interface and only require coordinated
discarding of RAM to work.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Pankaj Gupta <pankaj.gupta@cloud.ionos.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Auger Eric <eric.auger@redhat.com>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Cc: teawater <teawaterz@linux.alibaba.com>
Cc: Marek Kedzierski <mkedzier@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210413095531.25603-13-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
vIOMMU support works already with RamDiscardManager as long as guests only
map populated memory. Both, populated and discarded memory is mapped
into &address_space_memory, where vfio_get_xlat_addr() will find that
memory, to create the vfio mapping.
Sane guests will never map discarded memory (e.g., unplugged memory
blocks in virtio-mem) into an IOMMU - or keep it mapped into an IOMMU while
memory is getting discarded. However, there are two cases where a malicious
guests could trigger pinning of more memory than intended.
One case is easy to handle: the guest trying to map discarded memory
into an IOMMU.
The other case is harder to handle: the guest keeping memory mapped in
the IOMMU while it is getting discarded. We would have to walk over all
mappings when discarding memory and identify if any mapping would be a
violation. Let's keep it simple for now and print a warning, indicating
that setting RLIMIT_MEMLOCK can mitigate such attacks.
We have to take care of incoming migration: at the point the
IOMMUs get restored and start creating mappings in vfio, RamDiscardManager
implementations might not be back up and running yet: let's add runstate
priorities to enforce the order when restoring.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Auger Eric <eric.auger@redhat.com>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Cc: teawater <teawaterz@linux.alibaba.com>
Cc: Marek Kedzierski <mkedzier@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210413095531.25603-10-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
Although RamDiscardManager can handle running into the maximum number of
DMA mappings by propagating errors when creating a DMA mapping, we want
to sanity check and warn the user early that there is a theoretical setup
issue and that virtio-mem might not be able to provide as much memory
towards a VM as desired.
As suggested by Alex, let's use the number of KVM memory slots to guess
how many other mappings we might see over time.
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Auger Eric <eric.auger@redhat.com>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Cc: teawater <teawaterz@linux.alibaba.com>
Cc: Marek Kedzierski <mkedzier@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210413095531.25603-9-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
Let's query the maximum number of possible DMA mappings by querying the
available mappings when creating the container (before any mappings are
created). We'll use this informaton soon to perform some sanity checks
and warn the user.
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Auger Eric <eric.auger@redhat.com>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Cc: teawater <teawaterz@linux.alibaba.com>
Cc: Marek Kedzierski <mkedzier@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210413095531.25603-8-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
Implement support for RamDiscardManager, to prepare for virtio-mem
support. Instead of mapping the whole memory section, we only map
"populated" parts and update the mapping when notified about
discarding/population of memory via the RamDiscardListener. Similarly, when
syncing the dirty bitmaps, sync only the actually mapped (populated) parts
by replaying via the notifier.
Using virtio-mem with vfio is still blocked via
ram_block_discard_disable()/ram_block_discard_require() after this patch.
Reviewed-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Auger Eric <eric.auger@redhat.com>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Cc: teawater <teawaterz@linux.alibaba.com>
Cc: Marek Kedzierski <mkedzier@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210413095531.25603-7-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
Let's properly notify when (un)plugging blocks, after discarding memory
and before allowing the guest to consume memory. Handle errors from
notifiers gracefully (e.g., no remaining VFIO mappings) when plugging,
rolling back the change and telling the guest that the VM is busy.
One special case to take care of is replaying all notifications after
restoring the vmstate. The device starts out with all memory discarded,
so after loading the vmstate, we have to notify about all plugged
blocks.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Auger Eric <eric.auger@redhat.com>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Cc: teawater <teawaterz@linux.alibaba.com>
Cc: Marek Kedzierski <mkedzier@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210413095531.25603-6-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
Any errors are unexpected and ram_block_discard_range() already properly
prints errors. Let's stop manually reporting errors.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Auger Eric <eric.auger@redhat.com>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Cc: teawater <teawaterz@linux.alibaba.com>
Cc: Marek Kedzierski <mkedzier@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210413095531.25603-5-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
Let's factor out the core logic, no need to replicate.
Reviewed-by: Pankaj Gupta <pankaj.gupta@cloud.ionos.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: Pankaj Gupta <pankaj.gupta.linux@gmail.com>
Cc: Peter Xu <peterx@redhat.com>
Cc: Auger Eric <eric.auger@redhat.com>
Cc: Wei Yang <richard.weiyang@linux.alibaba.com>
Cc: teawater <teawaterz@linux.alibaba.com>
Cc: Marek Kedzierski <mkedzier@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20210413095531.25603-4-david@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
The MAX34451 is a Maxim power-supply system manager that can monitor up to 16 voltage rails or currents. It also contains a temperature sensor and supports up to four external temperature sensors.
This commit adds support for interfacing with it, and setting limits on the supported sensors.
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-5-titusr@google.com>
[Moved the device to the sensor directory]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
The ADM1272 is a PMBus compliant Hot Swap Controller and Digital Power
Monitor by Analog Devices.
This commit adds support for interfacing with it, and support for
setting and monitoring sensor limits.
Datasheet: https://www.analog.com/media/en/technical-documentation/data-sheets/ADM1272.pdf
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-3-titusr@google.com>
[Moved the device to the sensor directory]
[remove include of trace.h, it is not needed]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
QEMU has support for SMBus devices, and PMBus is a more specific
implementation of SMBus. The additions made in this commit makes it easier to
add new PMBus devices to QEMU.
https://pmbus.org/specification-archives/
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Hao Wu <wuhaotsh@google.com>
Signed-off-by: Titus Rwantare <titusr@google.com>
Message-Id: <20210708172556.1868139-2-titusr@google.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
1) watchdog_expired is set bool which value could only be 0 or 1,
but watchdog_expired every bit mean different Timer Use.
2) Use the command -ipmitool mc get watchdog- to query
ipmi-watchdog status in guest.
...
[root@localhost ~]# ipmitool mc watchdog get
Watchdog Timer Use: SMS/OS (0x44)
Watchdog Timer Is: Started/Running
Watchdog Timer Actions: Hard Reset (0x01)
Pre-timeout interval: 0 seconds
Timer Expiration Flags: 0x00
Initial Countdown: 60 sec
Present Countdown: 57 sec
...
bool for watchdog_expired results -Timer Expiration Flags- always
be 0x00 or 0x01, but the -Timer Expiration Flags- indicts the Timer Use
after timeout. So change watchdog_expired data type from bool to uint8_t
to fix this problem.
Signed-off-by: Jinhua Cao <caojinhua1@huawei.com>
Message-Id: <20210625021232.73614-1-caojinhua1@huawei.com>
[I checked, a bool and uint8 are the same size for the vmstate transfer,
so this should be fine.]
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
To ease reviewing code using the I2C bus API, introduce the
i2c_start_recv() and i2c_start_send() helpers which don't
take the confusing 'is_recv' boolean argument.
Use these new helpers in the SMBus / AUX bus models.
Suggested-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
To allow further simplications, extract i2c_do_start_transfer()
from i2c_start_transfer(). This is mostly the same function,
but the former is static and takes an enum argument.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
Make the argument representing the direction of the transfer a
boolean type.
Rename the boolean argument as 'is_recv' to match i2c_recv_send().
Document the function prototype.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Message-Id: <20200621145235.9E241745712@zero.eik.bme.hu>
[PMD: Split patch, added docstring]
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
Other functions from I2C slave API are named "i2c_slave_XXX()".
Follow that pattern with set_address(). Add docstring along.
No logical change.
Patch created mechanically using:
$ sed -i s/i2c_set_slave_address/i2c_slave_set_address/ \
$(git grep -l i2c_set_slave_address)
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
We replaced all the i2c_send_recv() calls by the clearer i2c_recv()
and i2c_send(), so we can remove this confusing API.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
Instead of using the confuse i2c_send_recv(), replace
i2c_send_recv(send = true) by i2c_send() and
i2c_send_recv(send = false) by i2c_recv().
During the replacement we also change a while() statement by for().
The resulting code is easier to review.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
Remove the 'is_write' boolean by directly using its value in place.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
To allow further simplifications in the following commits,
start copying WRITE_I2C code to the READ_I2C, and READ_I2C_MOT
to WRITE_I2C_MOT. No logical change.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
Since its introduction in commit 6fc7f77fd2 i2c_start_transfer()
uses incorrectly the direction of the transfer (the last argument
is called 'is_recv'). Fix by inverting the argument, we now have
is_recv = !is_write.
Fixes: 6fc7f77fd2 ("introduce aux-bus")
Reported-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
Instead of using the confuse i2c_send_recv(), rewrite to directly
call i2c_recv() & i2c_send(), resulting in code easier to review.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
It took me a while to find this model datasheet, since it is
an OCR scan. Add a reference to save other developers time.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
Instead of using the confuse i2c_send_recv(), rewrite to directly
call i2c_recv() & i2c_send(), resulting in code easier to review.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
Define TYPE_LM8323 in the public "hw/input/lm832x.h"
header and use it in hw/arm/nseries.c.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
lm832x_key_event() is specific go LM832x devices, not to the
I2C bus API. Move it out of "i2c.h" to a new header.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Acked-by: Corey Minyard <cminyard@mvista.com>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
|
|
move kvm files into kvm/
After the reshuffling, update MAINTAINERS accordingly.
Make use of the new directory:
target/s390x/kvm/
Signed-off-by: Claudio Fontana <cfontana@suse.de>
Signed-off-by: Cho, Yu-Chen <acho@suse.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210707105324.23400-14-acho@suse.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
|