| Age | Commit message (Collapse) | Author |
|---|
|
According to the FEC chapter of i.MX25 reference manual
When writing the MMFR register, bit 29 and 28 select the requested operation.
* 10 means read operation with valid MII mgmt frame
* 11 means read operation with non compliant MII mgmt frame
* 01 means write operation with valid MII mgmt frame
* 00 means write operation with non compliant MII mgmt frame
So while bit 28 does change beween read/write for valid MII mgmt frame, the
mening is inverted for non compliant MII mgmt frame.
Bit 29 on the other hand means read/write whatever the type of mgmt frame
involved.
So this patch change the operation selection from bit 28 to bit 29 as it is
more generic.
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
This patch introduces emulation for the Intel 82574 adapter, AKA e1000e.
This implementation is derived from the e1000 emulation code, and
utilizes the TX/RX packet abstractions that were initially developed for
the vmxnet3 device. Although some parts of the introduced code may be
shared with e1000, the differences are substantial enough so that the
only shared resources for the two devices are the definitions in
hw/net/e1000_regs.h.
Similarly to vmxnet3, the new device uses virtio headers for task
offloads (for backends that support virtio extensions). Usage of
virtio headers may be forcibly disabled via a boolean device property
"vnet" (which is enabled by default). In such case task offloads
will be performed in software, in the same way it is done on
backends that do not support virtio headers.
The device code is split into two parts:
1. hw/net/e1000e.c: QEMU-specific code for a network device;
2. hw/net/e1000e_core.[hc]: Device emulation according to the spec.
The new device name is e1000e.
Intel specifications for the 82574 controller are available at:
http://www.intel.com/content/dam/doc/datasheet/82574l-gbe-controller-datasheet.pdf
Throughput measurement results (iperf2):
Fedora 22 guest, TCP, RX
4 ++------------------------------------------+
| |
| X X X X X
3.5 ++ X X X X |
| X |
| |
3 ++ |
G | X |
b | |
/ 2.5 ++ |
s | |
| |
2 ++ |
| |
| |
1.5 X+ |
| |
+ + + + + + + + + + + +
1 ++--+---+---+---+---+---+---+---+---+---+---+
32 64 128 256 512 1 2 4 8 16 32 64
B B B B B KB KB KB KB KB KB KB
Buffer size
Fedora 22 guest, TCP, TX
18 ++-------------------------------------------+
| X |
16 ++ X X X X X
| X |
14 ++ |
| |
12 ++ |
G | X |
b 10 ++ |
/ | |
s 8 ++ |
| |
6 ++ X |
| |
4 ++ |
| X |
2 ++ X |
X + + + + + + + + + + +
0 ++--+---+---+---+---+----+---+---+---+---+---+
32 64 128 256 512 1 2 4 8 16 32 64
B B B B B KB KB KB KB KB KB KB
Buffer size
Fedora 22 guest, UDP, RX
3 ++------------------------------------------+
| X
| |
2.5 ++ |
| |
| |
2 ++ X |
G | |
b | |
/ 1.5 ++ |
s | X |
| |
1 ++ |
| |
| X |
0.5 ++ |
| X |
X + + + + +
0 ++-------+--------+-------+--------+--------+
32 64 128 256 512 1
B B B B B KB
Datagram size
Fedora 22 guest, UDP, TX
1 ++------------------------------------------+
| X
0.9 ++ |
| |
0.8 ++ |
0.7 ++ |
| |
G 0.6 ++ |
b | |
/ 0.5 ++ |
s | X |
0.4 ++ |
| |
0.3 ++ |
0.2 ++ X |
| |
0.1 ++ X |
X X + + + +
0 ++-------+--------+-------+--------+--------+
32 64 128 256 512 1
B B B B B KB
Datagram size
Windows 2012R2 guest, TCP, RX
3.2 ++------------------------------------------+
| X |
3 ++ |
| |
2.8 ++ |
| |
2.6 ++ X |
G | X X X X X
b 2.4 ++ X X |
/ | |
s 2.2 ++ |
| |
2 ++ |
| X X |
1.8 ++ |
| |
1.6 X+ |
+ + + + + + + + + + + +
1.4 ++--+---+---+---+---+---+---+---+---+---+---+
32 64 128 256 512 1 2 4 8 16 32 64
B B B B B KB KB KB KB KB KB KB
Buffer size
Windows 2012R2 guest, TCP, TX
14 ++-------------------------------------------+
| |
| X X
12 ++ |
| |
10 ++ |
| |
G | |
b 8 ++ |
/ | X |
s 6 ++ |
| |
| |
4 ++ X |
| |
2 ++ |
| X X X |
+ X X + + X X + + + + +
0 X+--+---+---+---+---+----+---+---+---+---+---+
32 64 128 256 512 1 2 4 8 16 32 64
B B B B B KB KB KB KB KB KB KB
Buffer size
Windows 2012R2 guest, UDP, RX
1.6 ++------------------------------------------X
| |
1.4 ++ |
| |
1.2 ++ |
| X |
| |
G 1 ++ |
b | |
/ 0.8 ++ |
s | |
0.6 ++ X |
| |
0.4 ++ |
| X |
| |
0.2 ++ X |
X + + + + +
0 ++-------+--------+-------+--------+--------+
32 64 128 256 512 1
B B B B B KB
Datagram size
Windows 2012R2 guest, UDP, TX
0.6 ++------------------------------------------+
| X
| |
0.5 ++ |
| |
| |
0.4 ++ |
G | |
b | |
/ 0.3 ++ X |
s | |
| |
0.2 ++ |
| |
| X |
0.1 ++ |
| X |
X X + + + +
0 ++-------+--------+-------+--------+--------+
32 64 128 256 512 1
B B B B B KB
Datagram size
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Code that will be shared moved to a separate files.
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
To make this device and network packets
abstractions ready for IOMMU.
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
This patch extends the TX/RX packet abstractions with features that will
be used by the e1000e device implementation.
Changes are:
1. Support iovec lists for RX buffers
2. Deeper RX packets parsing
3. Loopback option for TX packets
4. Extended VLAN headers handling
5. RSS processing for RX packets
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
This patch drops "vmx" prefix from packet abstractions names
to emphasize the fact they are generic and not tied to any
specific network device.
These abstractions will be reused by e1000e emulation implementation
introduced by following patches so their names need generalization.
This patch (except renamed files, adjusted comments and changes in MAINTAINTERS)
was produced by:
git grep -lz 'vmxnet_tx_pkt' | xargs -0 perl -i'' -pE "s/vmxnet_tx_pkt/net_tx_pkt/g"
git grep -lz 'vmxnet_rx_pkt' | xargs -0 perl -i'' -pE "s/vmxnet_rx_pkt/net_rx_pkt/g"
git grep -lz 'VmxnetTxPkt' | xargs -0 perl -i'' -pE "s/VmxnetTxPkt/NetTxPkt/g"
git grep -lz 'VMXNET_TX_PKT' | xargs -0 perl -i'' -pE "s/VMXNET_TX_PKT/NET_TX_PKT/g"
git grep -lz 'VmxnetRxPkt' | xargs -0 perl -i'' -pE "s/VmxnetRxPkt/NetRxPkt/g"
git grep -lz 'VMXNET_RX_PKT' | xargs -0 perl -i'' -pE "s/VMXNET_RX_PKT/NET_RX_PKT/g"
sed -ie 's/VMXNET_/NET_/g' hw/net/vmxnet_rx_pkt.c
sed -ie 's/VMXNET_/NET_/g' hw/net/vmxnet_tx_pkt.c
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Added support for PCIe CAP v1, while reusing some of the existing v2
infrastructure.
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
This function will be used by e1000e device code.
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
into staging
ppc patch queue for 2016-05-31
Here's another ppc patch queue. This batch is all preliminaries
towards two significant features:
1) Full hypervisor-mode support for POWER8
Patches 1-8 start fixing various bugs with TCG's handling of
hypervisor mode
2) CPU hotplug support
Patches 9-12 make some preliminary fixes towards implementing CPU
hotplug on ppc64 (and other non-x86 platforms). These patches are
actually to generic code, not ppc, but are included here with
Paolo's ACK.
# gpg: Signature made Tue 31 May 2016 01:39:44 BST using RSA key ID 20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.7-20160531:
cpu: Add a sync version of cpu_remove()
cpu: Reclaim vCPU objects
exec: Do vmstate unregistration from cpu_exec_exit()
exec: Remove cpu from cpus list during cpu_exec_exit()
ppc: Add PPC_64H instruction flag to POWER7 and POWER8
ppc: Get out of emulation on SMT "OR" ops
ppc: Fix sign extension issue in mtmsr(d) emulation
ppc: Change 'invalid' bit mask of tlbiel and tlbie
ppc: tlbie, tlbia and tlbisync are HV only
ppc: Do some batching of TCG tlb flushes
ppc: Use split I/D mmu modes to avoid flushes on interrupts
ppc: Remove MMU_MODEn_SUFFIX definitions
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
On ppc64 especially, we flush the tlb on any slbie or tlbie instruction.
However, those instructions often come in bursts of 3 or more (context
switch will favor a series of slbie's for example to an slbia if the
SLB has less than a certain number of entries in it, and tlbie's can
happen in a series, with PAPR, H_BULK_REMOVE can remove up to 4 entries
at a time.
Doing a tlb_flush() each time is a waste of time. We end up doing a memset
of the whole TLB, reloading it for the next instruction, memset'ing again,
etc...
Those instructions don't have to take effect immediately. For slbie, they
can wait for the next context synchronizing event. For tlbie, the next
tlbsync.
This implements batching by keeping a flag that indicates that we have a
TLB in need of flushing. We check it on interrupts, rfi's, isync's and
tlbsync and flush the TLB if needed.
This reduces the number of tlb_flush() on a boot to a ubuntu installer
first dialog screen from roughly 360K down to 36K.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[clg: added a 'CPUPPCState *' variable in h_remove() and
h_bulk_remove() ]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: removed spurious whitespace change, use 0/1 not true/false
consistently, since tlb_need_flush has int type]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Move the old qemu_ram_addr_from_host to memory_region_from_host and
make it return an offset within the region. For qemu_ram_addr_from_host
return the ram_addr_t directly, similar to what it was before
commit 1b5ec23 ("memory: return MemoryRegion from qemu_ram_addr_from_host",
2013-07-04).
Reviewed-by: Marc-André Lureau <marcandre.lureau@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Remove direct uses of ram_addr_t and optimize memory_region_{get,set}_fd
now that a MemoryRegion knows its RAMBlock directly.
Reviewed-by: Marc-André Lureau <marcandre.lureau@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The rationale is similar to the above mode sense response interception:
this is practically the only channel to communicate restraints from
elsewhere such as host and block driver.
The scsi bus we attach onto can have a larger max xfer len than what is
accepted by the host file system (guarding between the host scsi LUN and
QEMU), in which case the SG_IO we generate would get -EINVAL.
Signed-off-by: Fam Zheng <famz@redhat.com>
Message-Id: <1464243305-10661-3-git-send-email-famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Using pread/pwrite or io_submit has the advantage of eliminating the
bounce buffer, but drops the SCSI status. This keeps the guest from
seeing unit attention codes, as well as statuses such as RESERVATION
CONFLICT. Because we know scsi-block operates on an SBC device we can
still use the DMA helpers with SG_IO; just remember to patch the CDBs
if the transfer is split into multiple segments.
This means that scsi-block will always use the thread-pool unfortunately,
instead of respecting aio=native.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Commonize all the checks for canceled requests and errors. The next patch
will add another case to check for, in order to handle passthrough commands.
There is no semantic change here; the only nontrivial modification is in
scsi_write_do_fua, where cancellation has been checked earlier by both
callers. Thus, the check is replaced with an assertion.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
scsi-block will be able to do FUA just by passing the request through
to the LUN (which is also more efficient); there is no need to emulate
it like we do for scsi-disk.
Add a new method to distinguish this.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
These are replacements for blk_aio_readv and blk_aio_writev that allow
customization of the data path. They reuse the DMA helpers' DMAIOFunc
callback type, so that the same function can be used in either the
QEMUSGList or the bounce-buffered case.
This customization will be needed in the next patch to do zero-copy
SG_IO on scsi-block.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This will be the place to add DMAIOFuncs in the next patch. There
are also a couple DeviceClass members that can be moved to the
abstract class's initialization function.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The usage of INT_MAX in this function confuses Coverity. I think
the defect is bogus, however there is no protection against
getting more than sizeof(s->inpkt) bytes from the character device
backend.
Rewrite the function to only fill in as much data as needed from
buf into s->inpkt. The plen variable is replaced by a simple
state machine and there is no need anymore to shift contents to
the beginning of s->inpkt.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
While doing MegaRAID SAS controller command frame lookup, routine
'megasas_lookup_frame' uses 'read_queue_head' value as an index
into 'frames[MEGASAS_MAX_FRAMES=2048]' array. Limit its value
within array bounds to avoid any OOB access.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <1464179110-18593-1-git-send-email-ppandit@redhat.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When reading MegaRAID SAS controller configuration via MegaRAID
Firmware Interface(MFI) commands, routine megasas_dcmd_cfg_read
uses an uninitialised local data buffer. Initialise this buffer
to avoid stack information leakage.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <1464178304-12831-1-git-send-email-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When setting MegaRAID SAS controller properties via MegaRAID
Firmware Interface(MFI) commands, a user supplied size parameter
is used to set property value. Use appropriate size value to avoid
OOB access issues.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Message-Id: <1464172291-2856-2-git-send-email-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The LSI SAS1068 Host Bus Adapter emulator in Qemu, periodically
looks for requests and fetches them. A loop doing that in
mptsas_fetch_requests() could run infinitely if 's->state' was
not operational. Move check to avoid such a loop.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Cc: qemu-stable@nongnu.org
Message-Id: <1464077264-25473-1-git-send-email-ppandit@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Vmware Paravirtual SCSI emulation uses command descriptors to
process SCSI commands. These descriptors come with their ring
buffers. A guest could set the ring buffer size to an arbitrary
value leading to OOB access issue. Add check to avoid it.
Reported-by: Li Qiang <liqiang6-s@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Cc: qemu-stable@nongnu.org
Message-Id: <1464000485-27041-1-git-send-email-ppandit@redhat.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@ravellosystems.com>
Reviewed-by: Dmitry Fleytman <dmitry@daynix.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
drop the qemu_char_get_next_serial and use chardev prop instead
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-Id: <1464158344-12266-6-git-send-email-zxq_yx_007@163.com>
Tested-by: Michael Walle <michael@walle.cc>
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
* Drop the old SysBus init function and use instance_init
* Call qemu_chr_add_handlers in the realize callback
* Use qdev chardev prop instead of qemu_char_get_next_serial
* Add lm32_uart_create function to create lm32 uart device
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-Id: <1464158344-12266-5-git-send-email-zxq_yx_007@163.com>
Tested-by: Michael Walle <michael@walle.cc>
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
* Drop the old SysBus init function
* Call qemu_chr_add_handlers in the realize callback
* Use qdev chardev prop instead of qemu_char_get_next_serial
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-Id: <1464158344-12266-4-git-send-email-zxq_yx_007@163.com>
Tested-by: Michael Walle <michael@walle.cc>
Acked-by: Michael Walle <michael@walle.cc>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
* Drop the old SysBus init function and use instance_init
* Call qemu_chr_add_handlers in the realize callback
* Use qdev chardev prop instead of qemu_char_get_next_serial
* Add etraxfs_ser_create function to create etraxfs serial device
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-Id: <1464158344-12266-3-git-send-email-zxq_yx_007@163.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
* Drop the old SysBus init function and use instance_init
* Call qemu_chr_add_handlers in the realize callback
Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com>
Message-Id: <1464158344-12266-2-git-send-email-zxq_yx_007@163.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
At the moment presence of vfio-pci devices on a bus affect the way
the guest view table is allocated. If there is no vfio-pci on a PHB
and the host kernel supports KVM acceleration of H_PUT_TCE, a table
is allocated in KVM. However, if there is vfio-pci and we do yet not
KVM acceleration for these, the table has to be allocated by
the userspace. At the moment the table is allocated once at boot time
but next patches will reallocate it.
This moves kvmppc_create_spapr_tce/g_malloc0 and their counterparts
to helpers.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The user could have picked LIOBN via the CLI but the device tree
rendering code would still use the value derived from the PHB index
(which is the default fallback if LIOBN is not set in the CLI).
This replaces SPAPR_PCI_LIOBN() with the actual DMA LIOBN value.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
There are possible racing situations involving hotplug events and
guest migration. For cases where a hotplug event is migrated, or
the guest is in the process of fetching device tree at the time of
migration, we need to ensure the device tree is created and
associated with the corresponding DRC for devices that were
hotplugged on the source, but 'coldplugged' on the target.
Signed-off-by: Jianjun Duan <duanj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This patch adds check for negative return value from get_image_size(),
where it is missing. It avoids unnecessary two function calls.
Signed-off-by: Zhou Jie <zhoujie2011@cn.fujitsu.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The last 8 bytes of the receive buffer list page (that has been supplied
by the guest with the H_REGISTER_LOGICAL_LAN call) contain a counter
for frames that have been dropped because there was no suitable receive
buffer available. This patch introduces code to use this field to
provide the information about dropped rx packets to the guest.
There it can be queried with "ethtool -S eth0 | grep rx_no_buffer".
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Currently, the spapr-vlan device is trying to flush the RX queue
after each RX buffer that has been added by the guest via the
H_ADD_LOGICAL_LAN_BUFFER hypercall. In case the receive buffer pool
was empty before, we only pass single packets to the guest this
way. This can cause very bad performance if a sender is trying
to stream fragmented UDP packets to the guest. For example when
using the UDP_STREAM test from netperf with UDP packets that are
much bigger than the MTU size, almost all UDP packets are dropped
in the guest since the chances are quite high that at least one of
the fragments got lost on the way.
When flushing the receive queue, it's much better if we'd have
a bunch of receive buffers available already, so that fragmented
packets can be passed to the guest in one go. To do this, the
spapr_vlan_receive() function should return 0 instead of -1 if there
are no more receive buffers available, so that receive_disabled = 1
gets temporarily set for the receive queue, and we have to delay
the queue flushing at the end of h_add_logical_lan_buffer() a little
bit by using a timer, so that the guest gets a chance to add multiple
RX buffers before we flush the queue again.
This improves the UDP_STREAM test with the spapr-vlan device a lot:
Running
netserver -p 44444 -L <guestip> -f -D -4
in the guest, and
netperf -p 44444 -L <hostip> -H <guestip> -t UDP_STREAM -l 60 -- -m 16384
in the host, I get the following values _without_ this patch:
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
229376 16384 60.00 1738970 0 3798.83
229376 60.00 23 0.05
That "0.05" means that almost all UDP packets got lost/discarded
at the receiving side.
With this patch applied, the value look much better:
Socket Message Elapsed Messages
Size Size Time Okay Errors Throughput
bytes bytes secs # # 10^6bits/sec
229376 16384 60.00 1789104 0 3908.35
229376 60.00 22818 49.85
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
into staging
VFIO updates 2016-05-26
- Infrastructure and quirks to support IGD assignment (Alex Williamson)
- Fixes to 128bit handling, IOMMU replay, IOMMU translation sanity
checking (Alexey Kardashevskiy)
# gpg: Signature made Thu 26 May 2016 18:50:29 BST using RSA key ID 3BB08B22
# gpg: Good signature from "Alex Williamson <alex.williamson@redhat.com>"
# gpg: aka "Alex Williamson <alex@shazbot.org>"
# gpg: aka "Alex Williamson <alwillia@redhat.com>"
# gpg: aka "Alex Williamson <alex.l.williamson@gmail.com>"
* remotes/awilliam/tags/vfio-update-20160526.1:
vfio: Check that IOMMU MR translates to system address space
memory: Fix IOMMU replay base address
vfio: Fix 128 bit handling when deleting region
vfio/pci: Add IGD documentation
vfio/pci: Add a separate option for IGD OpRegion support
vfio/pci: Intel graphics legacy mode assignment
vfio/pci: Setup BAR quirks after capabilities probing
vfio/pci: Consolidate VGA setup
vfio/pci: Fix return of vfio_populate_vga()
vfio: Create device specific region info helper
vfio: Enable sparse mmap capability
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
At the moment IOMMU MR only translate to the system memory.
However if some new code changes this, we will need clear indication why
it is not working so here is the check.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Since a788f227 "memory: Allow replay of IOMMU mapping notifications"
when new VFIO listener is added, all existing IOMMU mappings are
replayed. However there is a problem that the base address of
an IOMMU memory region (IOMMU MR) is ignored which is not a problem
for the existing user (which is pseries) with its default 32bit DMA
window starting at 0 but it is if there is another DMA window.
This stores the IOMMU's offset_within_address_space and adjusts
the IOVA before calling vfio_dma_map/vfio_dma_unmap.
As the IOMMU notifier expects IOVA offset rather than the absolute
address, this also adjusts IOVA in sPAPR H_PUT_TCE handler before
calling notifier(s).
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
7532d3cbf "vfio: Fix 128 bit handling" added support for 64bit IOMMU
memory regions when those are added to VFIO address space; however
removing code cannot cope with these as int128_get64() will fail on
1<<64.
This copies 128bit handling from region_add() to region_del().
Since the only machine type which is actually going to use 64bit IOMMU
is pseries and it never really removes them (instead it will dynamically
add/remove subregions), this should cause no behavioral change.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
The IGD OpRegion is enabled automatically when running in legacy mode,
but it can sometimes be useful in universal passthrough mode as well.
Without an OpRegion, output spigots don't work, and even though Intel
doesn't officially support physical outputs in UPT mode, it's a
useful feature. Note that if an OpRegion is enabled but a monitor is
not connected, some graphics features will be disabled in the guest
versus a headless system without an OpRegion, where they would work.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Enable quirks to support SandyBridge and newer IGD devices as primary
VM graphics. This requires new vfio-pci device specific regions added
in kernel v4.6 to expose the IGD OpRegion, the shadow ROM, and config
space access to the PCI host bridge and LPC/ISA bridge. VM firmware
support, SeaBIOS only so far, is also required for reserving memory
regions for IGD specific use. In order to enable this mode, IGD must
be assigned to the VM at PCI bus address 00:02.0, it must have a ROM,
it must be able to enable VGA, it must have or be able to create on
its own an LPC/ISA bridge of the proper type at PCI bus address
00:1f.0 (sorry, not compatible with Q35 yet), and it must have the
above noted vfio-pci kernel features and BIOS. The intention is that
to enable this mode, a user simply needs to assign 00:02.0 from the
host to 00:02.0 in the VM:
-device vfio-pci,host=0000:00:02.0,bus=pci.0,addr=02.0
and everything either happens automatically or it doesn't. In the
case that it doesn't, we leave error reports, but assume the device
will operate in universal passthrough mode (UPT), which doesn't
require any of this, but has a much more narrow window of supported
devices, supported use cases, and supported guest drivers.
When using IGD in this mode, the VM firmware is required to reserve
some VM RAM for the OpRegion (on the order or several 4k pages) and
stolen memory for the GTT (up to 8MB for the latest GPUs). An
additional option, x-igd-gms allows the user to specify some amount
of additional memory (value is number of 32MB chunks up to 512MB) that
is pre-allocated for graphics use. TBH, I don't know of anything that
requires this or makes use of this memory, which is why we don't
allocate any by default, but the specification suggests this is not
actually a valid combination, so the option exists as a workaround.
Please report if it's actually necessary in some environment.
See code comments for further discussion about the actual operation
of the quirks necessary to assign these devices.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Capability probing modifies wmask, which quirks may be interested in
changing themselves. Apply our BAR quirks after the capability scan
to make this possible.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Combine VGA discovery and registration. Quirks can have dependencies
on BARs, so the quirks push out until after we've scanned the BARs.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
This function returns success if either we setup the VGA region or
the host vfio doesn't return enough regions to support the VGA index.
This latter case doesn't make any sense. If we're asked to populate
VGA, fail if it doesn't exist and let the caller decide if that's
important.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Given a device specific region type and sub-type, find it. Also
cleanup return point on error in vfio_get_region_info() so that we
always return 0 with a valid pointer or -errno and NULL.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
|
