| Age | Commit message (Collapse) | Author |
|---|
|
Limit error messages resulting from bad guest behavior to avoid allowing
the guest to cause the control domain's disk to fill.
The first message in pci_msix_write() can simply be deleted, as this
is indeed bad guest behavior, but such out of bounds writes don't
really need to be logged.
The second one is more problematic, as there guest behavior may only
appear to be wrong: For one, the old logic didn't take the mask-all bit
into account. And then this shouldn't depend on host device state (i.e.
the host may have masked the entry without the guest having done so).
Plus these writes shouldn't be dropped even when an entry is unmasked.
Instead, if they can't be made take effect right away, they should take
effect on the next unmasking or enabling operation - the specification
explicitly describes such caching behavior. Until we can validly drop
the message (implementing such caching/latching behavior), issue the
message just once per MSI-X table entry.
Note that the log message in pci_msix_read() similar to the one being
removed here is not an issue: "addr" being of unsigned type, and the
maximum size of the MSI-X table being 32k, entry_nr simply can't be
negative and hence the conditonal guarding issuing of the message will
never be true.
This is XSA-130.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
|
|
It's being used by the hypervisor. For now simply mimic a device not
capable of masking, and fully emulate any accesses a guest may issue
nevertheless as simple reads/writes without side effects.
This is XSA-129.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
|
|
The old logic didn't work as intended when an access spanned multiple
fields (for example a 32-bit access to the location of the MSI Message
Data field with the high 16 bits not being covered by any known field).
Remove it and derive which fields not to write to from the accessed
fields' emulation masks: When they're all ones, there's no point in
doing any host write.
This fixes a secondary issue at once: We obviously shouldn't make any
host write attempt when already the host read failed.
This is XSA-128.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
|
|
This new C module will be used by ARM machine files to generate
platform bus node and their dynamic sysbus device tree nodes.
Dynamic sysbus device node addition is done in a machine init
done notifier. arm_register_platform_bus_fdt_creator does the
registration of this latter and is supposed to be called by
ARM machine files that support platform bus and their dynamic
sysbus. Addition of dynamic sysbus nodes is done only if the
user did not provide any dtb.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Shannon Zhao <zhaoshenglong@huawei.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 1433244554-12898-2-git-send-email-eric.auger@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
After introduction of kvm_arch_msi_data_to_gsi, kvm_gsi_direct_mapping
now can be set on ARM. Also kvm_msi_via_irqfd_allowed can be set,
depending on kernel irqfd support, hence enabling VIRTIO-PCI with
vhost back-end.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The masked interrupt status register should be the state of the interrupt
after masking.
There should be a logical AND instead of a logical OR between the
interrupt status and the interrupt mask.
Signed-off-by: Victor CLEMENT <victor.clement@openwide.fr>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 1433154824-6927-1-git-send-email-victor.clement@openwide.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add a GICv2m device to the virt board to enable MSIs on the generic PCI
host controller. We allocate 64 SPIs in the IRQ space for now (this can
be increased/decreased later) and map the GICv2m right after the GIC in
the memory map.
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1432897270-7780-5-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
In preparation for adding the GICv2m which requires address specifiers
and is a subnode of the gic, we extend the gic DT definition to specify
the #address-cells and #size-cells properties and add an empty ranges
property properties of the DT node, since this is required to add the
v2m node as a child of the gic node.
Note that we must also expand the irq-map to reference the gic with the
right address-cells as a consequence of this change.
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1432897270-7780-4-git-send-email-christoffer.dall@linaro.org
Suggested-by: Shanker Donthineni <shankerd@codeaurora.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The ARM GICv2m widget is a little device that handles MSI interrupt
writes to a trigger register and ties them to a range of interrupt lines
wires to the GIC. It has a few status/id registers and the interrupt wires,
and that's about it.
A board instantiates the device by setting the base SPI number and
number SPIs for the frame. The base-spi parameter is indexed in the SPI
number space only, so base-spi == 0, means IRQ number 32. When a device
(the PCI host controller) writes to the trigger register, the payload is
the GIC IRQ number, so we have to subtract 32 from that and then index
into our frame of SPIs.
When instantiating a GICv2m device, tell PCI that we have instantiated
something that can deal with MSIs. We rely on the board actually wiring
up the GICv2m to the PCI host controller.
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1432897270-7780-3-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Instead of passing the GIC phandle around between functions, add it to
the VirtBoardInfo just like we do for the clock_phandle. We are about
to add the v2m phandle as well, and it's easier not having to pass
around a bunch of phandles, return multiple values from functions, etc.
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Message-id: 1432897270-7780-2-git-send-email-christoffer.dall@linaro.org
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
All QMP commands use the "new" handler interface (mhandler.cmd_new).
Most HMP commands still use the traditional interface (mhandler.cmd),
but a few use the "new" one. Complicates handle_user_command() for no
gain, so I'm converting these to the traditional interface.
pcie_aer_inject_error's implementation is split into the
hmp_pcie_aer_inject_error() and pcie_aer_inject_error_print(). The
former is a peculiar crossbreed between HMP and QMP handler. On
success, it works like a QMP handler: store QDict through ret_data
parameter, return 0. Printing the QDict is left to
pcie_aer_inject_error_print(). On failure, it works more like an HMP
handler: print error to monitor, return negative number.
To convert to the traditional interface, turn
pcie_aer_inject_error_print() into a command handler wrapping around
hmp_pcie_aer_inject_error(). By convention, this command handler
should be called hmp_pcie_aer_inject_error(), so rename the existing
hmp_pcie_aer_inject_error() to do_pcie_aer_inject_error().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
|
|
commit 5cb18b3d7bff2a83275ee98af2a14eb9e21c93ab
TPM2 ACPI table support
was missing a file, so build with iasl fails
(build without iasl works since it uses the generated
hex files).
Reported-by: "Daniel P. Berrange" <berrange@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Based on patch by Nikolay Nikolaev:
Vhost-user will implement the multi queue support in a similar way
to what vhost already has - a separate thread for each queue.
To enable the multi queue functionality - a new command line parameter
"queues" is introduced for the vhost-user netdev.
Signed-off-by: Nikolay Nikolaev <n.nikolaev@virtualopensystems.com>
Signed-off-by: Changchun Ouyang <changchun.ouyang@intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Make features 64bit wide everywhere.
On migration a full 64bit guest_features field is sent if one of the
high bits is set, in addition to the lower 32bit guest_features field
which must stay for compatibility reasons. That way we send the lower
32 feature bits twice, but the code is simpler because we don't have
to split and compose the 64bit features into two 32bit fields.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Needed for virtio features which go from 32bit to 64bit with virtio 1.0
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
set_host_notifier and set_guest_notifiers supported by virtio-mmio now.
Most code copied from virtio-pci.
This makes it possible to use vhost-net with virtio-mmio,
improving performance by about 30%.
The kvm-arm does not yet support irqfd, need to fix the hard-coded part after
kvm-arm gets irqfd support.
Signed-off-by: Ying-Shiuan Pan <yingshiuan.pan@gmail.com>
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Signed-off-by: Shannon Zhao <zhaoshenglong@huawei.com>
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
|
|
Add encoding for ACPI DefIncrement Opcode.
Reviewed-by: Shannon Zhao <zhaoshenglong@huawei.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Add encoding for ACPI DefShiftRight Opcode.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
|
|
Add encoding for ACPI DefShiftLeft Opcode.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
|
|
Add encoding for ACPI DefIndex Opcode.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
|
|
Add encoding for ACPI DefLLess Opcode.
Reviewed-by: Shannon Zhao <zhaoshenglong@huawei.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Add encoding for ACPI DefAdd Opcode.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Shannon Zhao <shannon.zhao@linaro.org>
|
|
Add a TPM2 ACPI table if a TPM 2 is used in the backend.
Also add an SSDT for the TPM 2.
Rename tpm_find() to tpm_get_version() and have this function
return the version of the TPM found, TPMVersion_Unspec if
no TPM is found. Use the version number to build version
specific ACPI tables.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
In the TPM passthrough backend driver, modify the probing code so
that we can check whether a TPM 1.2 or TPM 2 is being used
and adapt the behavior of the TPM TIS accordingly.
Move the code that tested for a TPM 1.2 into tpm_utils.c
and extend it with test for probing for TPM 2. Have the
function return the version of TPM found.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Following the recent upgrade to version 1.3, extend the TPM TIS
interface with capabilities introduced for support of a TPM 2.
TPM TIS for TPM 2 introduced the following extensions beyond the
TPM TIS 1.3 (used for TPM 1.2):
- A new 32bit interface Id register was introduced.
- New flags for the status (STS) register were defined.
- New flags for the capability flags were defined.
Support the above if a TPM TIS 1.3 for TPM 2 is used with a TPM 2
on the backend side. Support the old TPM TIS 1.3 configuration if a
TPM 1.2 is being used. A subsequent patch will then determine which
TPM version is being used in the backend.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
GICv3 ITS distinguishes between devices by using hardwired device IDs passed on the bus.
This patch implements passing these IDs in qemu.
SMMU is also known to use stream IDs, therefore this addition can also be useful for
implementing platforms with SMMU.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Changes from v1:
- Added bus number to the stream ID
- Added stream ID not only to MSI-X, but also to plain MSI. Some common code was made into
msi_send_message() function.
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
build_append_namestringv() and aml_string() first calculate the
resulting string's length with vsnprintf(NULL, ...), then allocate,
then print for real. Simply use g_strdup_vprintf() or g_vasprintf()
instead.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
|
|
It is Very annoying to carry forward an outdatEd coNtroller with a mOdern
Machine type.
Hence, let us not instantiate the FDC when all of the following apply:
- the machine type is pc-q35-2.4 or later,
- "-device isa-fdc" is not passed on the command line (nor in the config
file),
- no "-drive if=floppy,..." is requested.
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: John Snow <jsnow@redhat.com>
Cc: "Gabriel L. Somlo" <gsomlo@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: qemu-block@nongnu.org
Suggested-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
|
|
The "no_floppy = 1" machine class setting causes "default_floppy" in
main() to become zero. Consequently, default_drive() will not call
drive_add() and drive_new() for IF_FLOPPY, index=0, meaning that no
default floppy drive will be created for the virtual machine. In that
case, board code should also not insist on the creation of the
board-default FDC.
The board-default FDC will still be created if the user requests a floppy
drive with "-drive if=floppy".
Additionally, separate FDCs can be specified manually with "-device
isa-fdc". They allow the
-device isa-fdc,driveA=...
syntax that is more flexible than the one required by the board-default
FDC:
-global isa-fdc.driveA=...
This patch doesn't change the behavior observably, as all Q35 machine
types have "no_floppy = 0".
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: John Snow <jsnow@redhat.com>
Cc: "Gabriel L. Somlo" <gsomlo@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: qemu-block@nongnu.org
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
|
|
Even if board code decides not to request the creation of the FDC (keyed
off board-level factors, to be determined later), we should create the FDC
nevertheless if the user passes '-drive if=floppy' on the command line.
Otherwise '-drive if=floppy' would break without explicit '-device
isa-fdc' on such boards.
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: John Snow <jsnow@redhat.com>
Cc: "Gabriel L. Somlo" <gsomlo@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: qemu-block@nongnu.org
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
|
|
This patch introduces no observable change, but it allows the callers of
pc_basic_device_init(), ie. pc_init1() and pc_q35_init(), to request (or
not request) the creation of the FDC explicitly.
At the moment both callers pass constant create_fdctrl=true (hence no
observable change).
Assuming a board passes create_fdctrl=false, "floppy" will be NULL on
output, and (beyond the FDC not being created) that NULL will be passed on
to pc_cmos_init(). Luckily, pc_cmos_init() already handles that case.
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: John Snow <jsnow@redhat.com>
Cc: "Gabriel L. Somlo" <gsomlo@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: qemu-block@nongnu.org
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
|
|
VIRTIO_PCI_QUEUE_MAX is not only used for pci, so rename it be generic.
Cc: Amit Shah <amit.shah@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This patch introduce a virtio-s390 specific device_plugged() function
and doing the number of virtqueue validation inside.
Cc: Alexander Graf <agraf@suse.de>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Cc: Alexander Graf <agraf@suse.de>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Cc: Alexander Graf <agraf@suse.de>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This patch introduces virtio_get_num_queues() which iterates the vqs
array and return the number of virtqueues used by device.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This patch passes error pointer to transport specific device_plugged()
callback. Through this way, device_plugged() can do some transport
specific check and fail. This will be uesd by following patches that
check the number of virtqueues against the transport limitation.
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Alexander Graf <agraf@suse.de>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Instead of adding queues for multiqueue during feature set. This patch
did this in .realize(), this will help the following patches that
count the number of virtqueues used in .device_plugged() callback.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Nearly all transports have been offering VIRTIO_F_NOTIFY_ON_EMPTY,
s390-virtio being the exception. There's no reason why it shouldn't
offer it as well, though (handling is done in core anyway), so let's
move it to the common virtio features.
While we're changing it anyway, fix the indentation for the
DEFINE_VIRTIO_COMMON_FEATURES macro.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This was copied from virtio-pci, but it doesn't make much sense for
ccw, as it doesn't have to handle the broken implementations this bit
is supposed to deal with. Remove it.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Move host_features from the individual transport proxies into
the virtio device. Transports may continue to add feature bits
during device plugging.
This should it make easier to offer different sets of host features
for virtio-1/transitional support.
Tested-by: Shannon Zhao <shannon.zhao@linaro.org>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
In the old times, we always had pvpanic in ACPI and a _STA method told
the guest not to use it. Automatic generation dropped the _STA method
as the specification says that missing _STA means enabled and working.
Some guests (Linux) had buggy drivers and this change made them unable
to utilize pvpanic.
A Linux patch is posted as well, but I think it's worth to make pvpanic
useable on old guests at the price of three lines and few bytes of SSDT.
The old _STA method was
Method (_STA, 0, NotSerialized) {
Store (PEST, Local0)
If (LEqual (Local0, Zero)) {
Return (Zero) }
Else {
Return (0x0F) }}
Igor pointed out that we don't need to use a method to return a constant
and that 0xB (don't show in UI) is the common definition now.
Also, the device used to be PEVT. (PEVT as in "panic event"?)
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
All pc-i440fx and pc-q35 init functions simply call the corresponding
compat function and then call the main init function. Use a macro to
generate that code.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The function is not needed anymore, we can simply call pc_init1()
directly.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This looks like a step backwards, but it will allow pc-0.1[0123] and
isapc to follow the same compat+init pattern used by the other
machine-types, allowing us to generate all init function using the same
macro later.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The helper is not needed anymore, as the PC machine classes are
registered using QOM directly.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Now that we have a DEFINE_PC_MACHINE helper macro that just requires an
initialization function, it is trivial to convert them to register a QOM
machine class directly, instead of using QEMUMachine.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This will simplify the DEFINE_PC_MACHINE macro, and will help us to
implement reuse of PC_COMPAT_* macros through class_init function reuse,
in the future.
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
