| Age | Commit message (Collapse) | Author |
|---|
|
Don't raise irq when not enabled.
Raise irq on enabling if DMA_INTR is set
Don't clear irq unless it was raised by DMA, as there are other irq sources
Don't set DMA_INTR bit spuriously.
v1->v2:
- Don't clear irq unless it was raised by DMA
- Raise irq on enabling if DMA_INTR is set
- Assume revertion of 787cfbc432bf1d353a77cbdb613754f3963371a3
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
This reverts commit 787cfbc432bf1d353a77cbdb613754f3963371a3.
|
|
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
Remove useless set to zero lines. Latency programming should be
done by BIOS, reset value is zero.
Add revision to APB, don't enable PCI_COMMAND_MASTER and set status
according to APB specification.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
Commit c2039bd0ffce8807e0eaac55254fde790825fa92 made rom loading
automatic for non-PC architectures. Remove now mostly unused
conditional rom loading support.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
This patch fixes 525e05147d5a3bdc08caa422d108c1ef71b584b5.
pci host bridge doesn't have header type of bridge.
The check should be by header type, instead of pci class device.
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mst/qemu
* 'for_anthony' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/qemu:
pci: fix pci_find_bus()
|
|
Export the physical block size in the ATA IDENTIFY command. The
other topology values are not supported in ATA so skip them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Export the physical block size in the READ CAPACITY (16) command,
and add the new block limits VPD page to export the minimum and
optiomal I/O sizes.
Note that we also need to bump the scsi revision level to SPC-2
as that is the minimum requirement by at least the Linux kernel
to try READ CAPACITY (16) first and look at the block limits VPD
page.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Export all topology information in the block config structure,
guarded by a new VIRTIO_BLK_F_TOPOLOGY feature flag.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Add three new qdev properties to export block topology information to
the guest. This is needed to get optimal I/O alignment for RAID arrays
or SSDs.
The options are:
- physical_block_size to specify the physical block size of the device,
this is going to increase from 512 bytes to 4096 kilobytes for many
modern storage devices
- min_io_size to specify the minimal I/O size without performance impact,
this is typically set to the RAID chunk size for arrays.
- opt_io_size to specify the optimal sustained I/O size, this is
typically the RAID stripe width for arrays.
I decided to not auto-probe these values from blkid which might easily
be possible as I don't know how to deal with these issues on migration.
Note that we specificly only set the physical_block_size, and not the
logial one which is the unit all I/O is described in. The reason for
that is that IDE does not support increasing the logical block size and
at last for now I want to stick to one meachnisms in queue and allow
for easy switching of transports for a given backing image which would
not be possible if scsi and virtio use real 4k sectors, while ide only
uses the physical block exponent.
To make this more common for the different block drivers introduce a
new BlockConf structure holding all common block properties and a
DEFINE_BLOCK_PROPERTIES macro to add them all together, mirroring
what is done for network drivers. Also switch over all block drivers
to use it, except for the floppy driver which has weird driveA/driveB
properties and probably won't require any advanced block options ever.
Example usage for a virtio device with 4k physical block size and
8k optimal I/O size:
-drive file=scratch.img,media=disk,cache=none,id=scratch \
-device virtio-blk-pci,drive=scratch,physical_block_size=4096,opt_io_size=8192
aliguori: updated patch to take into account BLOCK events
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
The addition of the whole ATA IDENTIY page caused the config space to
go above the allowed size in the PCI spec, and thus the feature was
already reverted in the Linux guest driver and disabled by default in
qemu.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
It's not needed to check the return of qobject_from_jsonf()
anymore, as an assert() has been added there.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Fix a race condition where qemu finds that there are not enough virtio
ring buffers available and the guest make more buffers available before
qemu can enable notifications.
Signed-off-by: Tom Lendacky <toml@us.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
This fixes a segfault due to buffer overrun in the usb-serial device.
The memcpy was incrementing the start location by recv_used yet, the
computation of first_size (how much to write at the end of the buffer
before wrapping to the front) was not accounting for it. This causes the
next element after the receive buffer (recv_ptr) to get overwritten with
random data.
Signed-off-by: David Ahern <daahern@cisco.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
I have streaming audio devices working within qemu-kvm. This is a port
of the changes to qemu.
Streaming audio generates a series of isochronous requests that are
repetitive and time sensitive. The URBs need to be submitted in
consecutive USB frames and responses need to be handled in a timely manner.
Summary of the changes for isochronous requests:
1. The initial 'valid' value is increased to 32. It needs to be higher
than its current value of 10 since the host adds a 10 frame delay to the
scheduling of the first request; if valid is set to 10 the first
isochronous request times out and qemu cancels it. 32 was chosen as a
nice round number, and it is used in the path where a TD-async pairing
already exists.
2. The token field in the TD is *not* unique for isochronous requests,
so it is not a good choice for finding a matching async request. The
buffer (where to write the guest data) is unique, so use that value instead.
3. TD's for isochronous request need to be completed in the async
completion handler so that data is pushed to the guest as soon as it is
available. The uhci code currently attempts to process complete
isochronous TDs the next time the UHCI frame with the request is
processed. The results in lost data since the async requests will have
long since timed out based on the valid parameter. Increasing the valid
value is not acceptable as it introduces a 1+ second delay in the data
getting pushed to the guest.
4. The frame timer needs to be run on 1 msec intervals. Currently, the
expire time for the processing the next frame is computed after the
processing of each frame. This regularly causes the scheduling of frames
to shift in time. When this happens the periodic scheduling of the
requests is broken and the subsequent request is seen as a new request
by the host resulting in a 10 msec delay (first isochronous request is
scheduled for 10 frames from when the URB is submitted).
[ For what's worth a small change is needed to the guest driver to have
more outstanding URBs (at least 4 URBs with 5 packets per URB).]
Signed-off-by: David Ahern <daahern@cisco.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Just call bdrv_mon_event() in the right place.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Just call bdrv_mon_event() in the right place.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Just call bdrv_mon_event() in the right place.
Signed-off-by: Luiz Capitulino <lcapitulino@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
When the MMUCR TI bit is set, all the UTLB and ITLB entries should be
flushed.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
|
|
|
|
The write the the PA_POWOFF register is currently ignored. Fix that by
calling qemu_system_shutdown_request() when a poweroff is requested.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
|
|
typo in c021f8e65f5009a5ab5711d9d5326fcab553ef1c.
comparison fix.
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
dprintf is already claimed by POSIX[1], and on at least one system
is implemented as a macro
[1] http://www.opengroup.org/onlinepubs/9699919799/functions/dprintf.html
Signed-off-by: malc <av1474@comtv.ru>
|
|
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
|
|
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
When several PCI bridges were in use, monitor command "info pci" would
enter into infinite loop. Buses behind the bridge were not discoverable
because secondary and subordinate bus numbers were not used properly.
Other buses were not found because bus search terminated on first miss.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
It's currently not used by PPC machines. Refactor so that also Sparc64
machines can use it.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
The vmport "device" accesses the VCPU registers, so it requires proper
cpu_synchronize_state. Add it to vmport_ioport_read, which also
synchronizes vmport_ioport_write.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
|
|
This provides the same information as reverted commit 2ba6edf0. Not
much, just better than nothing.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Option "-device DRIVER,?" and monitor command "device_add DRIVER,?"
print the supported properties instead of creating a device. The
former also terminates the program.
This is commit 2ba6edf0 (just reverted) done right.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
This reverts commit 2ba6edf0dd740166632df80caa85992b20791a68.
The commit has two issues:
* When it runs from the monitor, e.g. "device_add e1000,?", it prints
to stderr instead of the monitor.
* Help looks to callers just like failed device creation. This makes
main() exit unsuccessfully on "-device e1000,?".
We need to do this differently.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
This reverts commit 922910ce42d15bdb7c2347436b1b5798b5401de4.
The commit has four issues:
* When it runs from the monitor, e.g. "device_add e1000,mac=?", it
prints to stderr instead of the monitor.
* Help looks to callers just like failed device creation. This makes
main() exit unsuccessfully on "-device e1000,mac=?".
* It has an undocumented side effect on -global: "-global e1000.mac=?"
prints help, but only when we actually add an e1000 device.
* It does not work for properties that accept the value "?".
We need to do this differently.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Help was shoehorned into device creation, qdev_device_add(). Since
help doesn't create a device, it returns NULL, which looks to callers
just like failed device creation. Monitor handler do_device_add()
doesn't care, but main() exits unsuccessfully.
Move help out of device creation, into new qdev_device_help().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Also add reset control.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
This requires an updated OpenBIOS image.
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
If an I/O request fails right away instead of getting an error only in the
callback, we still need to consider rerror/werror.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Current code assumes that only write requests are ever going to be restarted.
This is wrong since rerror=stop exists. Instead of directly starting writes,
use the same request processing as used for new requests.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
We need a function that handles a single request. Create one by splitting out
code from virtio_blk_handle_output.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
This fixes CONFIG_FB_CIRRUS for Linux guests and probably much more:
When switching away from linearly mapped vram, we also have to restore
the I/O handlers for the LFB.
This regression was once introduced by commit 2bec46dc97.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
This commit enables one to use multiple virtio-serial devices and to
assign ports to arbitrary devices like this:
-device virtio-serial,id=foo -device virtio-serial,id=bar \
-device virtserialport,bus=foo.0,name=foo \
-device virtserialport,bus=bar.0,name=bar
Signed-off-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
sparc64 timer has tick counter which can be set and read,
and tick compare value used as deadline to fire timer interrupt.
The timer is not used as periodic timer, instead deadline
is set each time new timer interrupt is needed.
v3 -> v4:
- coding style
v2 -> v3:
- added missing timer debug output macro
- CPUTimer struct and typedef moved to cpu.h
- change CPU_SAVE_VERSION to 6, older save formats not supported
v1 -> v2:
- new conversion helpers cpu_to_timer_ticks and timer_to_cpu_ticks
- save offset from clock source to implement cpu_tick_set_count
- renamed struct sun4u_timer to CPUTimer
- load and save cpu timers
v0 -> v1:
- coding style
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
Buffer block writes to avoid flushing every word access onto backing
storage device. This significantly speeds up flash emulation for flashes
connected through an 8 or 16-bit bus combined with backing storage (-pflash).
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@petalogix.com>
|
