aboutsummaryrefslogtreecommitdiff
path: root/hw/sd
AgeCommit message (Collapse)Author
2018-05-15sdcard: Correct CRC16 offset in sd_function_switch()Philippe Mathieu-Daudé
Per the Physical Layer Simplified Spec. "4.3.10.4 Switch Function Status": The block length is predefined to 512 bits and "4.10.2 SD Status": The SD Status contains status bits that are related to the SD Memory Card proprietary features and may be used for future application-specific usage. The size of the SD Status is one data block of 512 bit. The content of this register is transmitted to the Host over the DAT bus along with a 16-bit CRC. Thus the 16-bit CRC goes at offset 64. Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Message-id: 20180509060104.4458-3-f4bug@amsat.org Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-04-10hw/sd/bcm2835_sdhost: Don't raise spurious interruptsPeter Maydell
The Linux bcm2835_sdhost driver doesn't work on QEMU, because our model raises spurious data interrupts. Our function bcm2835_sdhost_fifo_run() will flag an interrupt any time it is called with s->datacnt == 0, even if the host hasn't actually issued a data read or write command yet. This means that the driver gets a spurious data interrupt as soon as it enables IRQs and then does something else that causes us to call the fifo_run routine, like writing to SDHCFG, and before it does the write to SDCMD to issue the read. The driver's IRQ handler then spins forever complaining that there's no data and the SD controller isn't in a state where there's going to be any data: [ 41.040738] sdhost-bcm2835 3f202000.mmc: fsm 1, hsts 00000000 [ 41.042059] sdhost-bcm2835 3f202000.mmc: fsm 1, hsts 00000000 (continues forever). Move the interrupt flag setting to more plausible places: * for BUSY, raise this as soon as a BUSYWAIT command has executed * for DATA, raise this when the FIFO has any space free (for a write) or any data in it (for a read) * for BLOCK, raise this when the data count is 0 and we've actually done some reading or writing This is pure guesswork since the documentation for this hardware is not public, but it is sufficient to get the Linux bcm2835_sdhost driver to work. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Tested-by: Gerd Hoffmann <kraxel@redhat.com> Message-id: 20180319161556.16446-3-peter.maydell@linaro.org
2018-04-10hw/sd/bcm2835_sdhost: Add tracepointsPeter Maydell
Add some tracepoints to the bcm2835_sdhost driver, to assist debugging. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Tested-by: Gerd Hoffmann <kraxel@redhat.com> Message-id: 20180319161556.16446-2-peter.maydell@linaro.org
2018-03-23sdhci: fix incorrect use of Error *Paolo Bonzini
Detected by Coverity (CID 1386072, 1386073, 1386076, 1386077). local_err was unused, and this made the static analyzer unhappy. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Message-id: 20180320151355.25854-1-pbonzini@redhat.com Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-03-12hw: Do not include "sysemu/block-backend.h" if it is not necessaryThomas Huth
After reviewing a patch from Philippe that removes block-backend.h from hw/lm32/milkymist.c, I noticed that this header is included unnecessarily in a lot of other files, too. Remove those unneeded includes to speed up the compilation process a little bit. Signed-off-by: Thomas Huth <thuth@redhat.com> Message-Id: <1518684912-31637-1-git-send-email-thuth@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2018-03-09sdhci: Fix a typo in commentPhilippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Message-id: 20180309153654.13518-8-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-03-09sdcard: Add the Tuning Command (CMD19)Philippe Mathieu-Daudé
From the "Physical Layer Simplified Specification Version 3.01": A known data block ("Tuning block") can be used to tune sampling point for tuning required hosts. [...] This procedure gives the system optimal timing for each specific host and card combination and compensates for static delays in the timing budget including process, voltage and different PCB loads and skews. [...] Data block, carried by DAT[3:0], contains a pattern for tuning sampling position to receive data on the CMD and DAT[3:0] line. [based on a patch from Alistair Francis <alistair.francis@xilinx.com> from qemu/xilinx tag xilinx-v2015.2] Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180309153654.13518-5-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-03-09sdcard: Display which protocol is used when tracing (SD or SPI)Philippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Message-id: 20180309153654.13518-4-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-03-09sdcard: Display command name when tracing CMD/ACMDPhilippe Mathieu-Daudé
The SDBus will reuse these functions, so we put them in a new source file. Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Message-id: 20180309153654.13518-3-f4bug@amsat.org Reviewed-by: Peter Maydell <peter.maydell@linaro.org> [PMM: slight wordsmithing of comments, added note that string returned does not need to be freed] Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-03-09sdcard: Do not trace CMD55, except when we already expect an ACMDPhilippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Acked-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180309153654.13518-2-f4bug@amsat.org Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: simplify SD_SEND_OP_COND (ACMD41)Philippe Mathieu-Daudé
replace switch(single case) -> if() Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215221325.7611-17-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: simplify SEND_IF_COND (CMD8)Philippe Mathieu-Daudé
replace switch(single case) -> if() Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215221325.7611-16-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: warn if host uses an incorrect address for APP CMD (CMD55)Philippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215221325.7611-15-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: check the card is in correct state for APP CMD (CMD55)Philippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215221325.7611-14-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: handles more commands in SPI modePhilippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215221325.7611-13-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: use a more descriptive label 'unimplemented_spi_cmd'Philippe Mathieu-Daudé
Suggested-by: Alistair Francis <alistair.francis@xilinx.com> Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215221325.7611-12-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: handle the Security Specification commandsPhilippe Mathieu-Daudé
returning sd_illegal, since they are not implemented. Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215221325.7611-11-f4bug@amsat.org [PMM: tweak multiline comment format] Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: handle CMD54 (SDIO)Philippe Mathieu-Daudé
Linux uses it to poll the bus before polling for a card. Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215221325.7611-10-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: use the registerfields API for the CARD_STATUS register masksPhilippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Acked-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215221325.7611-9-f4bug@amsat.org Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: use the correct masked OCR in the R3 replyPhilippe Mathieu-Daudé
use the registerfields API to access the OCR register Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215221325.7611-8-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: simplify using the ldst APIPhilippe Mathieu-Daudé
the code is easier to review/refactor. Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215221325.7611-7-f4bug@amsat.org Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: remove commands from unsupported old MMC specificationPhilippe Mathieu-Daudé
This device does not model MMCA Specification previous to v4.2 Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215221325.7611-6-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: clean the SCR register and add few commentsPhilippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215221325.7611-5-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: fix the 'maximum data transfer rate' to 25MHzPhilippe Mathieu-Daudé
To comply with Spec v1.10 (and 2.00, 3.01): . TRAN_SPEED for current SD Memory Cards that field must be always 0_0110_010b (032h) which is equal to 25MHz - the mandatory maximum operating frequency of SD Memory Card. Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215221325.7611-4-f4bug@amsat.org [PMM: fixed comment indent] Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: update the CSD CRC register regardless the CSD structure versionPhilippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215221325.7611-3-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: Don't always set the high capacity bitPhilippe Mathieu-Daudé
Don't set the high capacity bit by default as it will be set if required in the sd_set_csd() function. [based on a patch from Alistair Francis <alistair.francis@xilinx.com> and Peter Ogden <ogden@xilinx.com> from qemu/xilinx tag xilinx-v2015.4] Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215221325.7611-2-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: use the registerfields API to access the OCR registerPhilippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215220540.6556-12-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: use G_BYTE from cutilsPhilippe Mathieu-Daudé
code is now easier to read. Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215220540.6556-11-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: define SDMMC_CMD_MAX instead of using the magic '64'Philippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215220540.6556-8-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: add more trace eventsPhilippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Acked-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215220540.6556-6-f4bug@amsat.org Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: replace fprintf() by qemu_hexdump()Philippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215220540.6556-5-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: add a trace event for command responsesPhilippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Message-id: 20180215220540.6556-4-f4bug@amsat.org Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: replace DPRINTF() by trace eventsPhilippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215220540.6556-3-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22sdcard: reorder SDState struct membersPhilippe Mathieu-Daudé
place card registers first, this will ease further code movements. Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180215220540.6556-2-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22hw/sd/ssi-sd: use the SDBus API, connect the SDCard to the busPhilippe Mathieu-Daudé
On reset the bus will reset the card, we can now drop the device_reset() call. Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20180216022933.10945-5-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22hw/sd/milkymist-memcard: expose a SDBus and connect the SDCard to itPhilippe Mathieu-Daudé
using the sdbus_*() API. Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Acked-by: Michael Walle <michael@walle.cc> Message-id: 20180216022933.10945-4-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22hw/sd/milkymist-memcard: split realize() out of SysBusDevice init()Philippe Mathieu-Daudé
Create the SDCard in the realize() function. Suggested-by: Michael Walle <michael@walle.cc> Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Acked-by: Michael Walle <michael@walle.cc> Message-id: 20180216022933.10945-3-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-22hw/sd/milkymist-memcard: use qemu_log_mask()Philippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Acked-by: Michael Walle <michael@walle.cc> Message-id: 20180216022933.10945-2-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2018-02-13sdhci: add Spec v4.2 register definitionsPhilippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Message-Id: <20180208164818.7961-31-f4bug@amsat.org>
2018-02-13sdhci: implement CMD/DAT[] fields in the Present State registerPhilippe Mathieu-Daudé
[based on a patch from Alistair Francis <alistair.francis@xilinx.com> from qemu/xilinx tag xilinx-v2015.2] Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-Id: <20180208164818.7961-23-f4bug@amsat.org>
2018-02-13sdhci: implement UHS-I voltage switchPhilippe Mathieu-Daudé
[based on a patch from Alistair Francis <alistair.francis@xilinx.com> from qemu/xilinx tag xilinx-v2015.2] Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-Id: <20180208164818.7961-22-f4bug@amsat.org>
2018-02-13sdbus: add trace eventsPhilippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-Id: <20180208164818.7961-21-f4bug@amsat.org>
2018-02-13sdhci: implement the Host Control 2 register (tuning sequence)Philippe Mathieu-Daudé
[based on a patch from Alistair Francis <alistair.francis@xilinx.com> from qemu/xilinx tag xilinx-v2015.2] Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-Id: <20180208164818.7961-20-f4bug@amsat.org>
2018-02-13sdhci: rename the hostctl1 registerPhilippe Mathieu-Daudé
As per the Spec v3.00 Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-Id: <20180208164818.7961-19-f4bug@amsat.org>
2018-02-13sdhci: add support for v3 capabilitiesPhilippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-Id: <20180208164818.7961-18-f4bug@amsat.org>
2018-02-13sdhci: check Spec v2 capabilities (DMA and 64-bit bus)Philippe Mathieu-Daudé
Incorrect value will throw an error. Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-Id: <20180208164818.7961-14-f4bug@amsat.org>
2018-02-13sdhci: Fix 64-bit ADMA2Sai Pavan Boddu
The 64-bit ADMA address is not converted to the cpu endianes correctly. This patch fixes the issue and uses a valid mask for the attribute data. Signed-off-by: Sai Pavan Boddu <saipava@xilinx.com> [AF: Re-write commit message] Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-Id: <20180208164818.7961-13-f4bug@amsat.org>
2018-02-13sdhci: replace DMA magic value by BLOCK_SIZE_MASKPhilippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-Id: <20180208164818.7961-12-f4bug@amsat.org>
2018-02-13sdhci: check the Spec v1 capabilities correctnessPhilippe Mathieu-Daudé
Incorrect value will throw an error. Note than Spec v2 is supported by default. Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-Id: <20180208164818.7961-11-f4bug@amsat.org>
2018-02-13sdhci: simplify sdhci_get_fifolen()Philippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-Id: <20180208164818.7961-10-f4bug@amsat.org>
generated by cgit v1.2.3 (git 2.26.2) at 2024-12-10 22:51:34 +0000