| Age | Commit message (Collapse) | Author |
|---|
|
Writes in PIO mode have two requirements:
- A data interrupt must be generated after a write command has been
issued to indicate that the chip is ready to receive data.
- A block interrupt must be generated after each block to indicate
that the chip is ready to receive the next data block.
Rearrange the code to make this happen. Tested on raspi3 (in PIO mode)
and raspi2 (in DMA mode).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Message-id: 1531779837-20557-1-git-send-email-linux@roeck-us.net
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The load/store API will ease further code movement.
Per the Physical Layer Simplified Spec. "3.6 Bus Protocol":
"In the CMD line the Most Significant Bit (MSB) is transmitted
first, the Least Significant Bit (LSB) is the last."
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The Linux bcm2835_sdhost driver doesn't work on QEMU, because our
model raises spurious data interrupts. Our function
bcm2835_sdhost_fifo_run() will flag an interrupt any time it is
called with s->datacnt == 0, even if the host hasn't actually issued
a data read or write command yet. This means that the driver gets a
spurious data interrupt as soon as it enables IRQs and then does
something else that causes us to call the fifo_run routine, like
writing to SDHCFG, and before it does the write to SDCMD to issue the
read. The driver's IRQ handler then spins forever complaining that
there's no data and the SD controller isn't in a state where there's
going to be any data:
[ 41.040738] sdhost-bcm2835 3f202000.mmc: fsm 1, hsts 00000000
[ 41.042059] sdhost-bcm2835 3f202000.mmc: fsm 1, hsts 00000000
(continues forever).
Move the interrupt flag setting to more plausible places:
* for BUSY, raise this as soon as a BUSYWAIT command has executed
* for DATA, raise this when the FIFO has any space free (for a write)
or any data in it (for a read)
* for BLOCK, raise this when the data count is 0 and we've
actually done some reading or writing
This is pure guesswork since the documentation for this hardware is
not public, but it is sufficient to get the Linux bcm2835_sdhost
driver to work.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180319161556.16446-3-peter.maydell@linaro.org
|
|
Add some tracepoints to the bcm2835_sdhost driver, to assist
debugging.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Gerd Hoffmann <kraxel@redhat.com>
Message-id: 20180319161556.16446-2-peter.maydell@linaro.org
|
|
This adds the BCM2835 SDHost controller from Arasan.
Signed-off-by: Clement Deschamps <clement.deschamps@antfield.fr>
Message-id: 20170224164021.9066-2-clement.deschamps@antfield.fr
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
