| Age | Commit message (Collapse) | Author |
|---|
|
There are two cases here: the first is when the TI command underflows, in which
case we raise INTR_BS to indicate an early change of phase, and the second is
when the TI command overflows because the host requested a transfer for more
data than is available. In the latter case force TC to zero so that the TI
completion logic executes correctly.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-30-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
esp_do_dma()
Ensure that the async_len checks for requesting data from the SCSI layer and
the TC == 0 checks to detect the end of the DMA transfer are consistent in both
do_dma_pdma_cb() and esp_do_dma(). In particular this involves adding the check
to see if the FIFO is at its low threshold since PDMA and mixed DMA and non-DMA
requests can leave data remaining in the FIFO.
At the same time update all the comments so that they are also consistent between
all similar code paths.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-29-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
Since esp_dma_done() is called in both cases, and ti_size cannot be zero
(otherwise esp_command_complete() would have been called instead), replace
the conditional logic with a single call to esp_dma_done().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-28-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
The following ti_cmd checks ensure that only DMA and non-DMA TI commmands will
can call into the esp_do_dma() and esp_do_nodma() callbacks.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-27-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
With the latest changes this condition cannot occur anymore and so the logic
can be completely removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-26-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
Now that the TC is updated for each PDMA access (rather than once the FIFO is
full) there is no need to adjust the TC at start of each DMA transfer if the
FIFO is not empty.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-25-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
In the case when more data is requested from the SCSI layer during a DMA data
transfer from a device, don't immediately fall through to the TC check logic.
Otherwise when TC is zero INTR_BS will be raised immediately rather than when
the next set of SCSI data is ready.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-24-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
Rather than wait for the FIFO to fill up before calling the PDMA callback, push
that logic directly into the from_device logic in do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-23-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
Ensure that esp_dma_done() is only called when TC is zero, which is currently
always the case for DMA transfers.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-22-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
No change to the condition itself, other than to clarify that esp_dma_done()
must be called when TC is zero.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-21-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
The TI end of transfer interrupt only occurs when the TC reaches zero and is
not related to the SCSI layer transfer.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-20-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
The internal state of the ESP sequencer is not affected when raising an interrupt
to indicate the end of a DMA transfer.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-19-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
There is no need to manually reset these values as the ESP emulation now
correctly handles them within its existing logic.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-18-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
This workaround is no longer required with the current code and so can be
removed.
[Note: whilst MacOS itself can boot correctly, removing this hack prevents
a bootable EMILE CDROM from working. This is caused by a separate bug which
will be fixed by a subsequent patch]
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-17-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
Following on from the recent changes to when the TC is updated, it is now
possible to remove another set of manual STAT_TC updates so that its state
is now managed within esp_set_tc().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-16-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
This function is used to set the current SCSI bus phase in the ESP_RSTAT register
without affecting any of flag bits.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-15-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
This is to ensure that STAT_TC is triggered during the right parts of the
transfer when it is controlled exclusively by the TC.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-14-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
Instead accumulate in the real FIFO as done in real hardware, and then transfer
to cmdfifo when we're ready to process the MESSAGE OUT and COMMAND phase data.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-13-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
The do_cmd variable is only set for the MESSAGE OUT and COMMAND phases i.e.
those which involve transfers from the host to the SCSI bus, and so the unused
case can be removed.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-12-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
esp_do_dma()
The ultimate aim is to for esp_do_dma() behaviour to be determined by the SCSI
bus phase, in which case it is necessary to have separate to/from device paths.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-11-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
Invert the logic so that the end of DMA transfer check becomes one that checks
for TC == 0 in the from device path in do_dma_pdma_cb().
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-10-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
This helps to simplify esp_reg_write() and potentially allows for a 2-level
deep FIFO to be implemented in future.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-9-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
zero
This should be exclusively managed by esp_set_tc() rather than being manually
set in multiple places. Start by removing the occurrences exclusive to PDMA
and command completion which are those that can be currently removed without
affecting any test images.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-8-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
This flag is set once the transfer counter counts down to zero.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-7-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
Since the DREQ value depends upon the result of the selection process, add a
workaround to each esp_select() to manually assert DREQ durring the MESSAGE OUT
and COMMAND phases.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-6-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
The FIFO contents should not be affected by performing SCSI target selection.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
The fifo8_pop_buf() function returns a pointer to the FIFO buffer up to the
specified length. Since the FIFO buffer is modelled as an array then once
the FIFO wraps around, only the continuous portion of the buffer can be
returned.
In future the use of continuous and unaligned accesses will advance the
internal FIFO head pointer, so modify esp_fifo_pop_buf() to ensure that
any wraparound content is also returned up to the requested length.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
Since get_cmd() can be called multiple times during a mixed FIFO/DMA request,
move the existing request cancel check into esp_select() which always occurs
at the start of new SCSI request.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
The FIFO contents should not be affected if the target selection fails.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20240112125420.514425-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
Block layer patches
- Allow concurrent BB context changes
- virtio: Re-enable notifications after drain
- virtio-blk: Fix missing use of irqfd
- scsi: Don't ignore most usb-storage properties
- blkio: Respect memory-alignment for bounce buffer allocations
- iotests tmpdir fixes
- virtio-blk: Code cleanups
# -----BEGIN PGP SIGNATURE-----
#
# iQJFBAABCAAvFiEE3D3rFZqa+V09dFb+fwmycsiPL9YFAmXEkwgRHGt3b2xmQHJl
# ZGhhdC5jb20ACgkQfwmycsiPL9Y3jA//TmSBVqHljauyImYOgCt8qCXACttV0xhQ
# Q5ldUNx/JmIFMoUR7OlpVAL2MtvdwE0jjY+sDlEmWtz4IFJcCsCTUCHZZb8blreb
# +mnMkqrQ6Nb3tPR2jeIknrXqNy1ffyjZItktjWXVcl6jaHB8YabHHqszs9DIaf4n
# lcKovBKxula8ckMgvm48wCwTtS7VEPeuC5FrOqUqTtuhg+QKp5ZVoyVFHtf6GKTD
# iuXzCd4yxu4fDKAthJJj4N1bQaOmCKU7K9N/665wj9P2TyfmwlBAfNwNAlYbdX1E
# Sv7eSioQs2+oUxmfD/PUsF7wTYtDCrSAUFn1kP/XdRyXPJR3dHGiBKV9w9CaWNrU
# y8rqOhxVcuoBLRljTF32BK4HniAREjRngtpT2FnQQIyedZrXIwyTAWjs+LW12T6O
# NMiU603Nl9ZYhO1et2+qspsVpNIfEpQWpK+OCon6E+ggj1ea+pfqU30VPx4JU05I
# VLiydluIbehSkRlTHgFcTgApmx843OGW7CvWfRyen86Cexgx3DEjJUQ4/bYqaCha
# yLIi91rToSDmtlzJrg9eYiMs5Y6vz+ORvvX5im1RlbUUb7Kx/LaA4BU/uArEbBt8
# xXm/grO4hFUGqtLgd2LIjWaHSsLoW4jKeEiExFUUfvH5DG9Zl5HmzFwu+DYxX+im
# MJLLetDJAWI=
# =8tc0
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 08 Feb 2024 08:38:32 GMT
# gpg: using RSA key DC3DEB159A9AF95D3D7456FE7F09B272C88F2FD6
# gpg: issuer "kwolf@redhat.com"
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6
* tag 'for-upstream' of https://repo.or.cz/qemu/kevin:
virtio-blk: avoid using ioeventfd state in irqfd conditional
virtio-blk: Use ioeventfd_attach in start_ioeventfd
virtio: Re-enable notifications after drain
virtio-scsi: Attach event vq notifier with no_poll
blkio: Respect memory-alignment for bounce buffer allocations
scsi: Don't ignore most usb-storage properties
virtio-blk: do not use C99 mixed declarations
iotests: give tempdir an identifying name
iotests: fix leak of tmpdir in dry-run mode
scsi: Await request purging
block-backend: Allow concurrent context changes
monitor: use aio_co_reschedule_self()
virtio-blk: declare VirtIOBlock::rq with a type
virtio-blk: add vq_rq[] bounds check in virtio_blk_dma_restart_cb()
virtio-blk: clarify that there is at least 1 virtqueue
virtio-blk: enforce iothread-vq-mapping validation
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
As of commit 38738f7dbbda90fbc161757b7f4be35b52205552 ("virtio-scsi:
don't waste CPU polling the event virtqueue"), we only attach an io_read
notifier for the virtio-scsi event virtqueue instead, and no polling
notifiers. During operation, the event virtqueue is typically
non-empty, but none of the buffers are intended to be used immediately.
Instead, they only get used when certain events occur. Therefore, it
makes no sense to continuously poll it when non-empty, because it is
supposed to be and stay non-empty.
We do this by using virtio_queue_aio_attach_host_notifier_no_poll()
instead of virtio_queue_aio_attach_host_notifier() for the event
virtqueue.
Commit 766aa2de0f29b657148e04599320d771c36fd126 ("virtio-scsi: implement
BlockDevOps->drained_begin()") however has virtio_scsi_drained_end() use
virtio_queue_aio_attach_host_notifier() for all virtqueues, including
the event virtqueue. This can lead to it being polled again, undoing
the benefit of commit 38738f7dbbda90fbc161757b7f4be35b52205552.
Fix it by using virtio_queue_aio_attach_host_notifier_no_poll() for the
event virtqueue.
Reported-by: Fiona Ebner <f.ebner@proxmox.com>
Fixes: 766aa2de0f29b657148e04599320d771c36fd126
("virtio-scsi: implement BlockDevOps->drained_begin()")
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Tested-by: Fiona Ebner <f.ebner@proxmox.com>
Reviewed-by: Fiona Ebner <f.ebner@proxmox.com>
Signed-off-by: Hanna Czenczek <hreitz@redhat.com>
Message-ID: <20240202153158.788922-2-hreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
usb-storage is for the most part just a wrapper around an internally
created scsi-disk device. It uses DEFINE_BLOCK_PROPERTIES() to offer all
of the usual block device properties to the user, but then only forwards
a few select properties to the internal device while the rest is
silently ignored.
This changes scsi_bus_legacy_add_drive() to accept a whole BlockConf
instead of some individual values inside of it so that usb-storage can
now pass the whole configuration to the internal scsi-disk. This enables
the remaining block device properties, e.g. logical/physical_block_size
or discard_granularity.
Buglink: https://issues.redhat.com/browse/RHEL-22375
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20240131130607.24117-1-kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
scsi_device_for_each_req_async() currently does not provide any way to
be awaited. One of its callers is scsi_device_purge_requests(), which
therefore currently does not guarantee that all requests are fully
settled when it returns.
We want all requests to be settled, because scsi_device_purge_requests()
is called through the unrealize path, including the one invoked by
virtio_scsi_hotunplug() through qdev_simple_device_unplug_cb(), which
most likely assumes that all SCSI requests are done then.
In fact, scsi_device_purge_requests() already contains a blk_drain(),
but this will not fully await scsi_device_for_each_req_async(), only the
I/O requests it potentially cancels (not the non-I/O requests).
However, we can have scsi_device_for_each_req_async() increment the BB
in-flight counter, and have scsi_device_for_each_req_async_bh()
decrement it when it is done. This way, the blk_drain() will fully
await all SCSI requests to be purged.
This also removes the need for scsi_device_for_each_req_async_bh() to
double-check the current context and potentially re-schedule itself,
should it now differ from the BB's context: Changing a BB's AioContext
with a root node is done through bdrv_try_change_aio_context(), which
creates a drained section. With this patch, we keep the BB in-flight
counter elevated throughout, so we know the BB's context cannot change.
Signed-off-by: Hanna Czenczek <hreitz@redhat.com>
Message-ID: <20240202144755.671354-3-hreitz@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
When the maximum count of SCRIPTS instructions is reached, the code
stops execution and returns, but fails to decrement the reentrancy
counter. This effectively renders the SCSI controller unusable
because on next entry the reentrancy counter is still above the limit.
This bug was seen on HP-UX 10.20 which seems to trigger SCRIPTS
loops.
Fixes: b987718bbb ("hw/scsi/lsi53c895a: Fix reentrancy issues in the LSI controller (CVE-2023-0330)")
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Message-ID: <20240128202214.2644768-1-svens@stackframe.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Helge Deller <deller@gmx.de>
Signed-off-by: Thomas Huth <thuth@redhat.com>
|
|
Even though the BLAST command isn't fully implemented in QEMU, the DMA_STAT_BCMBLT
bit should be set after the command has been issued to indicate that the command
has completed.
This fixes an issue with the DC390 DOS driver which issues the BLAST command as
part of its normal error recovery routine at startup, and otherwise sits in a
tight loop waiting for DMA_STAT_BCMBLT to be set before continuing.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-ID: <20240112131529.515642-5-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
|
|
interrupt
The setting of DMA_STAT_DONE at the end of a DMA transfer can be configured to
generate an interrupt, however the Linux driver manually checks for DMA_STAT_DONE
being set and if it is, considers that a DMA transfer has completed.
If DMA_STAT_DONE is set but the ESP device isn't indicating an interrupt then
the Linux driver considers this to be a spurious interrupt. However this can
occur in QEMU as there is a delay between the end of DMA transfer where
DMA_STAT_DONE is set, and the ESP device raising its completion interrupt.
This appears to be an incorrect assumption in the Linux driver as the ESP and
PCI DMA interrupt sources are separate (and may not be raised exactly
together), however we can work around this by synchronising the setting of
DMA_STAT_DONE at the end of a DMA transfer with the ESP completion interrupt.
In conjunction with the previous commit Linux is now able to correctly boot
from an am53c974 PCI SCSI device on the hppa C3700 machine without emitting
"iget: checksum invalid" and "Spurious irq, sreg=10" errors.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-ID: <20240112131529.515642-4-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
|
|
The am53c974/dc390 PCI interrupt has two separate sources: the first is from the
internal ESP device, and the second is from the PCI DMA transfer logic.
Update the ESP interrupt handler so that it sets DMA_STAT_SCSIINT rather than
driving the PCI IRQ directly, and introduce a new esp_pci_update_irq() function
to generate the correct PCI IRQ level. In particular this fixes spurious interrupts
being generated by setting DMA_STAT_DONE at the end of a transfer if DMA_CMD_INTE_D
isn't set in the DMA_CMD register.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-ID: <20240112131529.515642-3-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
|
|
The current code in esp_pci_dma_memory_rw() sets the DMA address to the value
of the DMA_SPA (Starting Physical Address) register which is incorrect: this
means that for each callback from the SCSI layer the DMA address is set back
to the starting address.
In the case where only a single SCSI callback occurs (currently for transfer
lengths < 128kB) this works fine, however for larger transfers the DMA address
wraps back to the initial starting address, corrupting the buffer holding the
data transferred to the guest.
Fix esp_pci_dma_memory_rw() to use the DMA_WAC (Working Address Counter) for
the DMA address which is correctly incremented across multiple SCSI layer
transfers.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Message-ID: <20240112131529.515642-2-mark.cave-ayland@ilande.co.uk>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>
|
|
The term "QEMU global mutex" is identical to the more widely used Big
QEMU Lock ("BQL"). Update the code comments and documentation to use
"BQL" instead of "QEMU global mutex".
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Harsh Prateek Bora <harshpb@linux.ibm.com>
Message-id: 20240102153529.486531-6-stefanha@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
* configure: use a native non-cross compiler for linux-user
* meson: cleanups
* target/i386: miscellaneous cleanups and optimizations
* target/i386: implement CMPccXADD
* target/i386: the sgx_epc_get_section stub is reachable
* esp: check for NULL result from scsi_device_find()
# -----BEGIN PGP SIGNATURE-----
#
# iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAmWRImYUHHBib256aW5p
# QHJlZGhhdC5jb20ACgkQv/vSX3jHroNd7AgAgcyJGiMfUkXqhefplpm06RDXQIa8
# FuoJqPb21lO75DQKfaFRAc4xGLagjJROMJGHMm9HvMu2VlwvOydkQlfFRspENxQ/
# 5XzGdb/X0A7HA/mwUfnMB1AZx0Vs32VI5IBSc6acc9fmgeZ84XQEoM3KBQHUik7X
# mSkE4eltR9gJ+4IaGo4voZtK+YoVD8nEcuqmnKihSPWizev0FsZ49aNMtaYa9qC/
# Xs3kiQd/zPibHDHJu0ulFsNZgxtUcvlLHTCf8gO4dHWxCFLXGubMush83McpRtNB
# Qoh6cTLH+PBXfrxMR3zmTZMNvo8Euls3s07Y8TkNP4vdIIE/kMeMDW1wJw==
# =mq30
# -----END PGP SIGNATURE-----
# gpg: Signature made Sun 31 Dec 2023 08:12:22 GMT
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* tag 'for-upstream' of https://gitlab.com/bonzini/qemu: (46 commits)
meson.build: report graphics backends separately
configure, meson: rename targetos to host_os
meson: rename config_all
meson: remove CONFIG_ALL
meson: remove config_targetos
meson: remove CONFIG_POSIX and CONFIG_WIN32 from config_targetos
meson: remove OS definitions from config_targetos
meson: always probe u2f and canokey if the option is enabled
meson: move subdirs to "Collect sources" section
meson: move config-host.h definitions together
meson: move CFI detection code with other compiler flags
meson: keep subprojects together
meson: move accelerator dependency checks together
meson: move option validation together
meson: move program checks together
meson: add more sections to main meson.build
configure: unify again the case arms in probe_target_compiler
configure: remove unnecessary subshell
Makefile: clean qemu-iotests output
meson: use version_compare() to compare version
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add a 'current_lun' check for a null value
to avoid null pointer dereferencing and
recover host if NULL return
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 4eb8606560 (esp: store lun coming from the MESSAGE OUT phase)
Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru>
Message-ID: <20231229152647.19699-1-adiupina@astralinux.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-Id: <20231221031652.119827-52-richard.henderson@linaro.org>
|
|
It is required to use error_report() instead of error_reportf_err(), if the
prior function does not take local_err as the argument. As a result, the
local_err is always NULL and segment fault may happen.
vhost_scsi_start()
-> vhost_scsi_set_endpoint(s) --> does not allocate local_err
-> error_reportf_err()
-> error_vprepend()
-> g_string_append(newmsg, (*errp)->msg) --> (*errp) is NULL
In addition, add ": " at the end of other error_reportf_err() logs.
Fixes: 7962e432b4e4 ("vhost-user-scsi: support reconnect to backend")
Signed-off-by: Dongli Zhang <dongli.zhang@oracle.com>
Message-Id: <20231214003117.43960-1-dongli.zhang@oracle.com>
Reviewed-by: Feng Li <fengli@smartx.com>
Reviewed-by: Raphael Norwitz <raphael.norwitz@nutanix.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This adds support for vhost-scsi to be able to create a worker thread
per virtqueue. Right now for vhost-net we get a worker thread per
tx/rx virtqueue pair which scales nicely as we add more virtqueues and
CPUs, but for scsi we get the single worker thread that's shared by all
virtqueues. When trying to send IO to more than 2 virtqueues the single
thread becomes a bottlneck.
This patch adds a new setting, worker_per_virtqueue, which can be set
to:
false: Existing behavior where we get the single worker thread.
true: Create a worker per IO virtqueue.
Signed-off-by: Mike Christie <michael.christie@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-Id: <20231204231618.21962-3-michael.christie@oracle.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
|
|
The SCSI subsystem no longer uses the AioContext lock. Request
processing runs exclusively in the BlockBackend's AioContext since
"scsi: only access SCSIDevice->requests from one thread" and hence the
lock is unnecessary.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-ID: <20231205182011.1976568-13-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
The AioContext lock no longer has any effect. Remove it.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-ID: <20231205182011.1976568-9-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
Since the removal of AioContext locking, the correctness of the code
relies on running requests from a single AioContext at any given time.
Add assertions that verify that callbacks are invoked in the correct
AioContext.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Message-ID: <20231205182011.1976568-3-stefanha@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
Protect the Task Management Function BH state with a lock. The TMF BH
runs in the main loop thread. An IOThread might process a TMF at the
same time as the TMF BH is running. Therefore tmf_bh_list and tmf_bh
must be protected by a lock.
Run TMF request completion in the IOThread using aio_wait_bh_oneshot().
This avoids more locking to protect the virtqueue and SCSI layer state.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20231205182011.1976568-2-stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
blk_aio_*() doesn't require the AioContext lock and the SCSI subsystem's
internal state also does not anymore.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Acked-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20231204164259.1515217-4-stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
virtio_queue_aio_attach_host_notifier()
virtio_queue_aio_attach_host_notifier() does not require the AioContext
lock. Stop taking the lock and add an explicit smp_wmb() because we were
relying on the implicit barrier in the AioContext lock before.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Message-ID: <20231204164259.1515217-3-stefanha@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
