Age | Commit message (Collapse) | Author |
|
Commit afe0a595356192d5f79703cf6462fcc112df007c ("rtl8139: support byte
read to TxStatus registers") reused rtl8139_TxStatus_read() for reading
TxAddr registers. It relies on the fact that TxStatus[] and TxAddr[]
are adjacent.
This causes a gcc warning because the compiler can detect that array
access is out-of-bounds:
hw/rtl8139.c:2501:27: error: array subscript is above array bounds [-Werror=array-bounds]
This patch refactors the function so that we don't rely on out-of-bounds
accesses.
Cc: Jason Wang <jasonwang@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
According the spec, the card works in network/host communication mode only when
both EEM1 and EEM0 are unset in 93C46 Command Register (normal op
mode). So this patch check these bits before trying to receive packets.
As some guest driver (such as linux, see cp_init_hw() in 8139cp.c)
allocate rx ring after the recevier were enabled, this would cause our
emulation codes tries to dma into guest memory when the rx descriptor
is not properly configured. This patch fixes this.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
According to the spec, only when opmode is "Config. Register Write
Enable" could driver write to CONFIG0,1,3,4 and bits 13,12,8 of BMCR.
Currently, we allow modifying to those registers also when 8139 is in
"Auto-load" mode and "93C46 (93C56) Programming" mode. This patch
fixes this.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Reduce duplicated codes.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Some drivers (such as win7) use byte read for TxStatus registers, so we need to
support this to let guest driver behave correctly.
For writing, only double-word access is allowed by spec.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The tx buffer would be re-allocated for tx descriptor with big size
and without LS bit set, this would make guest driver could easily let
qemu to allocate unlimited.
In linux host, a glib failure were easy to be triggered:
GLib-ERROR **: gmem.c:176: failed to allocate 18446744071562067968 bytes
This patch fix this by adding a limit. As the spec didn't tell the maximum size
of buffer allowed, stick it to current CP_TX_BUFFER_SIZE (65536).
Changes from V1:
Drop the while statement and s->cplus_txbuffer check.
Signed-off-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Replace device_init() with generalized type_init().
While at it, unify naming convention: type_init([$prefix_]register_types)
Also, type_init() is a function, so add preceding blank line where
necessary and don't put a semicolon after the closing brace.
Signed-off-by: Andreas Färber <afaerber@suse.de>
Cc: Anthony Liguori <anthony@codemonkey.ws>
Cc: malc <av1474@comtv.ru>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
This was done in a mostly automated fashion. I did it in three steps and then
rebased it into a single step which avoids repeatedly touching every file in
the tree.
The first step was a sed-based addition of the parent type to the subclass
registration functions.
The second step was another sed-based removal of subclass registration functions
while also adding virtual functions from the base class into a class_init
function as appropriate.
Finally, a python script was used to convert the DeviceInfo structures and
qdev_register_subclass functions to TypeInfo structures, class_init functions,
and type_register_static calls.
We are almost fully converted to QOM after this commit.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
We already have a QOM interface for this so let's use it.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Right now, DeviceInfo acts as the class for qdev. In order to switch to a
proper ObjectClass derivative, we need to ween all of the callers off of
interacting directly with the info pointer.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
|
|
adress->address
advertisment->advertisement
begining->beginning
bondary->boundary
controler->controller
controll->control
convertion->conversion
doesnt->doesn't
existant->existent
instuction->instruction
loosing->losing
managment->management
multipled->multiplied
negotation->negotiation
runing->running
teh->the
unchangable->unchangeable
writen->written
yeild->yield
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
|
|
This patch removes some unnecessary casts in the rtl8139 device,
introduced by commit 3ada003aee2004d24f23b9cd6f4eda87d9601ddb
'rtl8139: Use PCI DMA stub functions'.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
This patch makes iPXE work with the rtl8139 emulation. The rtl8139
driver in iPXE issues a 16bit access on the ChipCmd register
(offset 0x37) to check the status of the rx buffer. The offset of the
ioport access was getting fixed up to 0x36 in qemu, causing the value
read in iPXE to be invalid.
This fixes an issue with iPXE reporting timeouts during TFTP transfers.
Reposting this here because it is trivial enough and the original post
on qemu-devel didn't attract much attention.
Also, the inw() which was causing the issue has been replaced with an
inb() in upstream iPXE:
https://git.ipxe.org/ipxe.git/commit/91dd64ad25baa27954a7518e73df4fca8a2d0c93
Signed-off-by: Julian Pidancet <julian.pidancet@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
|
|
This updates the rtl8139 device emulation to use the explicit PCI DMA
functions, instead of directly calling physical memory access functions.
Signed-off-by: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Fix up some erroneous comments in code:
interrupt pins are named A-D, the
interrupt pin register is always readonly
and isn't zeroed out on reset.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
qemu_malloc/qemu_free no longer exist after this commit.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Reviewed-by: Richard Henderson <rth@twiddle.net>
Reviewed-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Conflicts:
hw/virtio-pci.c
|
|
use PCIDeviceInfo to initialize ids.
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Replace writeable -> writable
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
|
|
Conflicts:
exec.c
|
|
Compilation for Windows needs a different declaration for the
printf format attribute, so use the macro which was defined for
this purpose.
Cc: Benjamin Poirier <benjamin.poirier@gmail.com>
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
|
|
gcc can check the format string for correctness even when debugging output is
not enabled.
Have to make sure arguments are always available. They are optimized out if
unneeded.
Signed-off-by: Benjamin Poirier <benjamin.poirier@gmail.com>
Cc: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
|
|
Removes double (( )) to make DEBUG_PRINT compatible with real function calls.
Change the name to DPRINTF to be consistent with other DPRINTF macros
throughout qemu.
Include the "RTL8139: " prefix in the macro. This changes some debug output
slightly since the prefix wasn't present on all lines.
Part of the change was done using the "coccinelle" tool with the following
small semantic match:
@@ expression E; @@
- DEBUG_PRINT((E))
+ DPRINTF(E)
Signed-off-by: Benjamin Poirier <benjamin.poirier@gmail.com>
Cc: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
|
|
Prevents a compilation failure when DEBUG_RTL8139 is defined:
CC libhw32/rtl8139.o
cc1: warnings being treated as errors
hw/rtl8139.c: In function ‘rtl8139_cplus_transmit_one’:
hw/rtl8139.c:1960: error: format ‘%8lx’ expects type ‘long unsigned int’, but argument 5 has type ‘target_phys_addr_t’
make[1]: *** [rtl8139.o] Error 1
Signed-off-by: Benjamin Poirier <benjamin.poirier@gmail.com>
Cc: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Reviewed-by: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
|
|
And add missing ROMs to tarbin build target.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Add support to the emulated hardware to insert vlan tags in packets
going from the guest to the network.
Signed-off-by: Benjamin Poirier <benjamin.poirier@gmail.com>
Cc: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
Add support to the emulated hardware to extract vlan tags in packets
going from the network to the guest.
Signed-off-by: Benjamin Poirier <benjamin.poirier@gmail.com>
Cc: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Blue Swirl <blauwirbel@gmail.com>
--
AFAIK, extraction is optional to get vlans working. The driver
requests rx detagging but should not assume that it was done. Under
Linux, the mac layer will catch the vlan ethertype. I only added this
part for completeness (to emulate the hardware more truthfully...)
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
clean out ifdef's around ethernet checksum calculation
Signed-off-by: Benjamin Poirier <benjamin.poirier@gmail.com>
Acked-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Blue Swirl <blauwirbel@gmail.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
This was done with:
sed -i 's/qemu_get_clock\>/qemu_get_clock_ns/' \
$(git grep -l 'qemu_get_clock\>' )
sed -i 's/qemu_new_timer\>/qemu_new_timer_ns/' \
$(git grep -l 'qemu_new_timer\>' )
after checking that get_clock and new_timer never occur twice
on the same line. There were no missed occurrences; however, even
if there had been, they would have been caught by the compiler.
There was exactly one false positive in qemu_run_timers:
- current_time = qemu_get_clock (clock);
+ current_time = qemu_get_clock_ns (clock);
which is of course not in this patch.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The initialization should not be only on reset but also when initializing
the device.
It resolves a bug when hot plugging a pci network device: the mac address
was always null.
Signed-off-by: William Dauchy <wdauchy@gmail.com>
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
rtl8139 includes a cpu_register_io_memory acquired value in it's
migration data. This is not only unecessary, but we should treat
these values as unique to the VM instances since the value depends
on call order. In most cases, this miraculously still works.
However, if devices are added or removed from the system, it may
represent an ordering change, which could cause the target rtl8139
device to make use of another device's cpu_register_io_memory value.
If we detect that a hot-add/remove has occured, include a subsection
to restrict migrations only to driver versions known to include this
fix.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
If bootindex is specified on command line a string that describes device
in firmware readable way is added into sorted list. Later this list will
be passed into firmware to control boot order.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
This patch replaces explicit bswaps with endianness hints to the
mmio layer.
Because we don't depend on the target endianness anymore, we can also
move the driver over to Makefile.objs.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
As stated before, devices can be little, big or native endian. The
target endianness is not of their concern, so we need to push things
down a level.
This patch adds a parameter to cpu_register_io_memory that allows a
device to choose its endianness. For now, all devices simply choose
native endian, because that's the same behavior as before.
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
Make rtl8139 spec compliant, fixing reset values
for command register.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Don't overwrite pci header type.
Otherwise, multi function bit which pci_init_header_type() sets
appropriately is lost.
Anyway PCI_HEADER_TYPE_NORMAL is zero, so it is unnecessary to zero
which is already zero cleared.
how to test:
run qemu and issue info pci to see whether a device in question is
normal device, not pci-to-pci bridge.
This is handy because guest os isn't required.
tested changes:
The following files are covered by using following commands.
sparc64-softmmu
apb_pci.c, vga-pci.c, cmd646.c, ne2k_pci.c, sun4u.c
ppc-softmmu
grackle_pci.c, cmd646.c, ne2k_pci.c, vga-pci.c, macio.c
ppc-softmmu -M mac99
unin_pci.c(uni-north, uni-north-agp)
ppc64-softmmu
pci-ohci, ne2k_pci, vga-pci, unin_pci.c(u3-agp)
x86_64-softmmu
acpi_piix4.c, ide/piix.c, piix_pci.c
-vga vmware vmware_vga.c
-watchdog i6300esb wdt_i6300esb.c
-usb usb-uhci.c
-sound ac97 ac97.c
-nic model=rtl8139 rtl8139.c
-nic model=pcnet pcnet.c
-balloon virtio virtio-pci.c:
untested changes:
The following changes aren't tested.
prep_pci.c: ppc-softmmu -M prep should cover, but core dumped.
unin_pci.c(uni-north-pci): the caller is commented out.
openpic.c: the caller is commented out in ppc_prep.c
Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Blue Swirl <blauwirbel@gmail.com>
|
|
Add a QEMU timer only when needed (timeout status not set, timeout
irq wanted and timer set).
This patch is required for Darwin. Patch has been tested under
FreeBSD, Darwin and Linux.
Signed-off-by: Frediano Ziglio <freddy77@gmail.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Currently we do not implement VLAN tagging for rtl8139(C+),
still data is read from ring buffer headers.
- augment unused assignment with TODO item
- cast txdw1 to void for now
Signed-off-by: Igor V. Kovalenko <igor.v.kovalenko@gmail.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
No functional changes. I verified that the generated binary
does not change.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Juan Quintela <quintela@redhat.com>
Acked-by: Glauber Costa <glommer@gmail.com>
|
|
This patch adds a romfile property to the pci bus. It allows to specify
a romfile to load into the rom bar of the pci device. The default value
comes from a new field in PCIDeviceInfo. The property allows to change
the file and also to disable the rom loading using an empty string.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Currently, we preload option roms into the option rom space in memory. This
prevents DDIM from functioning correctly which severely limits the number
of roms we can support.
This patch introduces a pci_add_option_rom() which registers the
PCI_ROM_ADDRESS bar which points to our option rom. It also converts over
the cirrus vga adapter, the rtl8139, virtio, and the e1000 to use this
new mechanism.
The result is that PXE boot functions even with three unique types of cards.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Signed-off-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|
|
rtl8139.c is using malloc()/free() instead of qemu_malloc()/qemu_free().
Fix it.
Signed-off-by: Jean-Christophe DUBOIS <jcd@tribudubois.net>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
|