| Age | Commit message (Collapse) | Author |
|---|
|
The four interrupts of the PCI bus are connected to the same UIC pin
on the real Sam460ex. Evidence for this can be found in the UBoot
source for the Sam460ex in the Sam460ex.c file where
PCI_INTERRUPT_LINE is written. Change the ppc440_pcix model to behave
more like this.
This fixes the problem that can be observed when adding further PCI
cards that got their interrupt rotated to other interrupts than PCI
INT A. In particular, the bug was observed with an additional OHCI PCI
card or an ES1370 sound device.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Tested-by: Sebastian Bauer <mail@sebastianbauer.info>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Commit 51b0d834c changed error handling to report file name in error
message but forgot to move freeing it after usage. Noticed by Coverity.
Fixes: CID 1394217
Reported-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This function was introduced between v2.11 and v2.12 to replace obsolete
ways of specifying the NUMA nodes for DIMMs. It's used to find the correct
node for an LMB, by locating which DIMM object it lies within.
Unfortunately, one of the checks is inverted, so we check whether the
address is less than two different things, rather than actually checking
a range. This introduced a regression, meaning that after a reboot qemu
will advertise incorrect node information for memory to the guest.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
|
|
sam460ex_load_device_tree() handles nearly all possible errors by simply
exiting (within helper functions and macros). It handles two early error
cases by returning an error.
There's no particular point to this, so make it handle those directly as
well, removing the need for the caller to handle a failure. As a bonus it
gives us more specific error messages.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The qemu_fdt_*() helper functions already exit with a message instead of
returning errors, so we don't need to check for errors in the caller.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
In a couple of places sam460ex_load_device_tree() calls "raw" libfdt
functions which can fail, but doesn't check for error codes. At best,
if these fail the guest will be silently started in a non-standard state,
or it could fail entirely.
Fix this by using the _FDT() helper macro which aborts on a libfdt failure.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Commit 29f9cef "ppc: Include vga cirrus card into the compiling process"
changed the default display adapter for all PPC machines to cirrus. Unfortunately
it missed setting the default display type to stdvga for both PReP machines
causing the display to fail to initialise under OpenHackWare.
Update the MachineClass for both prep and 40p machines so that the default
std(vga) display adapter is the default if no options are specified
which fixes the display for the PReP machines.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Missed in 3c409c1927e, hopefully reported by Coverity.
Fixes: Coverity CID 1393788 (Copy-paste error)
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
commit efe2add7cb7f ("spapr/vio: deprecate the "irq" property")
introduced get/set accessors for the "irq" property to warn of its
usage, but the warning in the get pollutes the monitor 'info qtree'.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Commit 29f9cef39e "ppc: Include vga cirrus card into the compiling process"
changed the default display adapter for all PPC machines to cirrus. Unfortunately
it missed setting the default display type to stdvga for both Mac machines
causing the display to fail to initialise under OpenBIOS.
Update the MachineClass for both Old World and New World Macs so that the
default std(vga) display adapter is the default if no options are specified
which fixes the display for the Mac machines.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
into staging
ppc patch queue 2018-07-03
Here's a last minue pull request before today's soft freeze. Ideally
I would have sent this earlier, but I was waiting for a couple of
extra fixes I knew were close. And the freeze crept up on me, like
always.
Most of the changes here are bugfixes in any case. There are some
cleanups as well, which have been in my staging tree for a little
while. There are a couple of truly new features (some extensions to
the sam460ex platform), but these are low risk, since they only affect
a new and not really stabilized machine type anyway.
Higlights are:
* Mac platform improvements from Mark Cave-Ayland
* Sam460ex improvements from BALATON Zoltan et al.
* XICS interrupt handler cleanups from Cédric Le Goater
* TCG improvements for atomic loads and stores from Richard
Henderson
* Assorted other bugfixes
# gpg: Signature made Tue 03 Jul 2018 06:55:22 BST
# gpg: using RSA key 6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-3.0-20180703: (35 commits)
ppc: Include vga cirrus card into the compiling process
target/ppc: Relax reserved bitmask of indexed store instructions
target/ppc: set is_jmp on ppc_tr_breakpoint_check
spapr: compute default value of "hpt-max-page-size" later
target/ppc/kvm: don't pass cpu to kvm_get_smmu_info()
target/ppc/kvm: get rid of kvm_get_fallback_smmu_info()
ppc440_uc: Basic emulation of PPC440 DMA controller
sam460ex: Add RTC device
hw/timer: Add basic M41T80 emulation
ppc4xx_i2c: Rewrite to model hardware more closely
hw/ppc: Give sam46ex its own config option
fpu_helper.c: fix setting FPSCR[FI] bit
target/ppc: Implement the rest of gen_st_atomic
target/ppc: Implement the rest of gen_ld_atomic
target/ppc: Use atomic min/max helpers
target/ppc: Use MO_ALIGN for EXIWX and ECOWX
target/ppc: Split out gen_st_atomic
target/ppc: Split out gen_ld_atomic
target/ppc: Split out gen_load_locked
target/ppc: Tidy gen_conditional_store
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
# Conflicts:
# hw/ppc/spapr.c
|
|
Drivers for this card exists on PPC-based AmigaOS guests so it is useful to
allow users to emulate the graphics card for PPC machines.
As cirrus vga is currently preferred over std(vga) in absence of any user
choice, this change also sets the default display of spapr machines to
std as otherwise qemu refuses to start these machines. Not specifying an
explicit graphics mode is for instance done by 'make check'.
Signed-off-by: Sebastian Bauer <mail@sebastianbauer.info>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
It is currently not possible to run a pseries-2.12 or older machine
with HV KVM. QEMU prints the following and exits right away.
qemu-system-ppc64: KVM doesn't support for base page shift 34
The "hpt-max-page-size" capability was recently added to spapr to hide
host configuration details from HPT mode guests. Its default value for
newer machine types is 64k.
For backwards compatibility, pseries-2.12 and older machine types need
a different value. This is handled as usual in a class init function.
The default value is 16G, ie, all page sizes supported by POWER7 and
newer CPUs, but HV KVM requires guest pages to be hpa contiguous as
well as gpa contiguous. The default value is the page size used to
back the guest RAM in this case.
Unfortunately kvmppc_hpt_needs_host_contiguous_pages()->kvm_enabled() is
called way before KVM init and returns false, even if the user requested
KVM. We thus end up selecting 16G, which isn't supported by HV KVM. The
default value must be set during machine init, because we can safely
assume that KVM is initialized at this point.
We fix this by moving the logic to default_caps_with_cpu(). Since the
user cannot pass cap-hpt-max-page-size=0, we set the default to 0 in
the pseries-2.12 class init function and use that as a flag to do the
real work.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
PPC440 SoCs such as the AMCC 460EX have a DMA controller which is used
by AmigaOS on the sam460ex. Implement the parts used by AmigaOS so it
can get further booting on the sam460ex machine.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The Sam460ex has an M41T80 serial RTC chip on I2C bus 0 at address 0x68.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
At present the Sam460ex board is activated by the general CONFIG_PPC4XX
option. However that includes the board for both ppc-softmmu and
(deprecated) ppcemb-softmmu builds. As Sam460ex is developed, that would
require adding more things into ppcemb-softmmu, which we don't want to do.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
commit d35aefa9ae15 ("ppc/pnv: introduce a new intc_create() operation
to the chip model") changed the object link in the pnv_core_realize()
routine but a return was forgotten in case of error, which can lead to
more problems afterwards (segv)
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
With the previous changes, we can now let the ICS_KVM class inherit
directly from ICS_BASE class and not from the intermediate ICS_SIMPLE.
It makes the class hierarchy much cleaner.
What is left in the top classes is the low level interface to access
the KVM XICS device in ICS_KVM and the XICS emulating handlers in
ICS_SIMPLE.
This should not break migration compatibility.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
sam460ex (or at least this emulation) does not support the "ibm,cpm" power
management. As a result, Linux crashes when trying to access it. Remove
its device tree node. Also, if/when we boot the Linux kernel directly,
serial port clock frequencies in the device tree file will be unset, and
serial port initialization will fail. Add valid frequency values to
the serial ports to be able to use it. Also set valid values for the other
clock nodes otherwise set by u-boot.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Commit 84051eb400 "adb: add property to disable direct reg 3 writes" added a
workaround for MacOS 9 incorrectly setting the mouse address during boot of
PMU machines.
Further testing has shown that since fb6649f172 "adb: fix read reg 3 byte
ordering" this can still sometimes happen with the CUDA mac99 machine,
so let's enable this workaround for all New World machines using ADB for now.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
It eases code review, unit is explicit.
Patch generated using:
$ git grep -E '(1024|2048|4096|8192|(<<|>>).?(10|20|30))' hw/ include/hw/
and modified manually.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20180625124238.25339-33-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
These files don't use anything exposed by "qemu/cutils.h",
simplify preprocessing including directly "qemu/units.h".
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au> (ppc parts)
Message-Id: <20180625124238.25339-7-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Code change produced with:
$ git ls-files | egrep '\.[ch]$' | \
xargs sed -i -e 's/\(\W[KMGTPE]\)_BYTE/\1iB/g'
Suggested-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au> (ppc parts)
Message-Id: <20180625124238.25339-6-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Let's try to reduce error handling a bit. In the plug/unplug case, the
device was realized and therefore we can assume that getting access to
the memory region will not fail.
For get_vmstate_memory_region() this is already handled that way.
Document both cases.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-13-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Let's rename it to make it look more consistent.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180619134141.29478-4-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Currently during KVM initialization on POWER, kvm_fixup_page_sizes()
rewrites a bunch of information in the cpu state to reflect the
capabilities of the host MMU and KVM. This overwrites the information
that's already there reflecting how the TCG implementation of the MMU will
operate.
This means that we can get guest-visibly different behaviour between KVM
and TCG (and between different KVM implementations). That's bad. It also
prevents migration between KVM and TCG.
The pseries machine type now has filtering of the pagesizes it allows the
guest to use which means it can present a consistent model of the MMU
across all accelerators.
So, we can now replace kvm_fixup_page_sizes() with kvm_check_mmu() which
merely verifies that the expected cpu model can be faithfully handled by
KVM, rather than updating the cpu model to match KVM.
We call kvm_check_mmu() from the spapr cpu reset code. This is a hack:
conceptually it makes more sense where fixup_page_sizes() was - in the KVM
cpu init path. However, doing that would require moving the platform's
pagesize filtering much earlier, which would require a lot of work making
further adjustments. There wouldn't be a lot of concrete point to doing
that, since the only KVM implementation which has the awkward MMU
restrictions is KVM HV, which can only work with an spapr guest anyway.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
|
|
KVM HV has some limitations (deriving from the hardware) that mean not all
host-cpu supported pagesizes may be usable in the guest. At present this
means that KVM guests and TCG guests may see different available page sizes
even if they notionally have the same vcpu model. This is confusing and
also prevents migration between TCG and KVM.
This patch makes the environment consistent by always allowing the same set
of pagesizes. Since we can't remove the KVM limitations, we do this by
always applying the same limitations it has, even to TCG guests.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
|
|
The way we used to handle KVM allowable guest pagesizes for PAPR guests
required some convoluted checking of memory attached to the guest.
The allowable pagesizes advertised to the guest cpus depended on the memory
which was attached at boot, but then we needed to ensure that any memory
later hotplugged didn't change which pagesizes were allowed.
Now that we have an explicit machine option to control the allowable
maximum pagesize we can simplify this. We just check all memory backends
against that declared pagesize. We check base and cold-plugged memory at
reset time, and hotplugged memory at pre_plug() time.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
|
|
The way the POWER Hash Page Table (HPT) MMU is virtualized by KVM HV means
that every page that the guest puts in the pagetables must be truly
physically contiguous, not just GPA-contiguous. In effect this means that
an HPT guest can't use any pagesizes greater than the host page size used
to back its memory.
At present we handle this by changing what we advertise to the guest based
on the backing pagesizes. This is pretty bad, because it means the guest
sees a different environment depending on what should be host configuration
details.
As a start on fixing this, we add a new capability parameter to the
pseries machine type which gives the maximum allowed pagesizes for an
HPT guest. For now we just create and validate the parameter without
making it do anything.
For backwards compatibility, on older machine types we set it to the max
available page size for the host. For the 3.0 machine type, we fix it to
16, the intention being to only allow HPT pagesizes up to 64kiB by default
in future.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
|
|
spapr_irq_alloc_block and spapr_irq_alloc() are now deprecated.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Today, when a device requests for IRQ number in a sPAPR machine, the
spapr_irq_alloc() routine first scans the ICSState status array to
find an empty slot and then performs the assignement of the selected
numbers. Split this sequence in two distinct routines : spapr_irq_find()
for lookups and spapr_irq_claim() for claiming the IRQ numbers.
This will ease the introduction of a static layout of IRQ numbers.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
spapr capabilities have an apply hook to actually activate (or deactivate)
the feature in the system at reset time. However, a number of capabilities
affect the setup of cpus, and need to be applied to each of them -
including hotplugged cpus for extra complication. To make this simpler,
add an optional cpu_apply hook that is called from spapr_cpu_reset().
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
|
|
Previously, the effective values of the various spapr capability flags
were only determined at machine reset time. That was a lazy way of making
sure it was after cpu initialization so it could use the cpu object to
inform the defaults.
But we've now improved the compat checking code so that we don't need to
instantiate the cpus to use it. That lets us move the resolution of the
capability defaults much earlier.
This is going to be necessary for some future capabilities.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
|
|
ppc_check_compat() is used in a number of places to check if a cpu object
supports a certain compatiblity mode, subject to various constraints.
It takes a PowerPCCPU *, however it really only depends on the cpu's class.
We have upcoming cases where it would be useful to make compatibility
checks before we fully instantiate the cpu objects.
ppc_type_check_compat() will now make an equivalent check, but based on a
CPU's QOM typename instead of an instantiated CPU object.
We make use of the new interface in several places in spapr, where we're
essentially making a global check, rather than one specific to a particular
cpu. This avoids some ugly uses of first_cpu to grab a "representative"
instance.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
|
|
The device tree node of the ISA bus was being partially done in
different places. Move all the nodes creation under the same routine.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
It introduces a base PnvChip class from which the specific processor
chip classes, Pnv8Chip and Pnv9Chip, inherit. Each of them needs to
define an init and a realize routine which will create the controllers
of the target processor. For the moment, the base PnvChip class
handles the XSCOM bus and the cores.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
QEMU implements the "Shared Processor LPAR" (SPLPAR) option, which allows
the hypervisor to time-slice a physical processor into multiple virtual
processor. The intent is to allow more guests to run, and to optimize
processor utilization.
The guest OS can cede idle VCPUs, so that their processing capacity may
be used by other VCPUs, with the H_CEDE hcall. The guest OS can also
optimize spinlocks, by confering the time-slice of a spinning VCPU to the
spinlock holder if it's currently notrunning, with the H_CONFER hcall.
Both hcalls depend on a "Virtual Processor Area" (VPA) to be registered
by the guest OS, generally during early boot. Other per-VCPU areas can
be registered: the "SLB Shadow Buffer" which allows a more efficient
dispatching of VCPUs, and the "Dispatch Trace Log Buffer" (DTL) which
is used to compute time stolen by the hypervisor. Both DTL and SLB Shadow
areas depend on the VPA to be registered.
The VPA/SLB Shadow/DTL are state that QEMU should migrate, but this doesn't
happen, for no apparent reason other than it was just never coded. This
causes the features listed above to stop working after migration, and it
breaks the logic of the H_REGISTER_VPA hcall in the destination.
The VPA is set at the guest request, ie, we don't have to migrate
it before the guest has actually set it. This patch hence adds an
"spapr_cpu/vpa" subsection to the recently introduced per-CPU machine
data migration stream.
Since DTL and SLB Shadow are optional and both depend on VPA, they get
their own subsections "spapr_cpu/vpa/slb_shadow" and "spapr_cpu/vpa/dtl"
hanging from the "spapr_cpu/vpa" subsection.
Note that this won't break migration to older QEMUs. Is is already handled
by only registering the vmstate handler for per-CPU data with newer machine
types.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
A per-CPU machine data pointer was recently added to PowerPCCPU. The
motivation is to to hide platform specific details from the core CPU
code. This per-CPU data can hold state which is relevant to the guest
though, eg, Virtual Processor Areas, and we should migrate this state.
This patch adds the plumbing so that we can migrate the per-CPU data
for PAPR guests. We only do this for newer machine types for the sake
of backward compatibility. No state is migrated for the moment: the
vmstate_spapr_cpu_state structure will be populated by subsequent
patches.
Signed-off-by: Greg Kurz <groug@kaod.org>
[dwg: Fix some trivial spelling and spacing errors]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This moves the details of the ISA bus creation under the LPC model but
more important, the new PnvChip operation will let us choose the chip
class to use when we introduce the different chip classes for Power9
and Power8. It hides away the processor chip controllers from the
machine.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
On Power9, the thread interrupt presenter has a different type and is
linked to the chip owning the cores.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Commit 3d85885a1b1f3 tried to fix error handling, but it actually
went into the wrong direction by dropping the local Error *.
In the default KVM case, the rationale is to try the in-kernel XICS first,
and if not possible, to fallback to userland XICS. Passing errp everywhere
makes this fallback impossible if errp is &error_fatal (which happens to
be the case). And anyway, if the caller would pass a regular &local_err,
things would be worse: we could possibly pass an already set *errp to
error_setg() and crash, or return an error even in case of success.
So we definitely need a local Error * and only propagate it when we're
done with the fallback logic. This is what this patch does.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
CPUPPCState currently contains a number of fields containing the state of
the VPA. The VPA is a PAPR specific concept covering several guest/host
shared memory areas used to communicate some information with the
hypervisor.
As a PAPR concept this is really machine specific information, although it
is per-cpu, so it doesn't really belong in the core CPU state structure.
There's also other information that's per-cpu, but platform/machine
specific. So create a (void *)machine_data in PowerPCCPU which can be
used by the machine to locate per-cpu data. Intialization, lifetime and
cleanup of machine_data is entirely up to the machine type.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Tested-by: Greg Kurz <groug@kaod.org>
|
|
This extracts from the PvChip realize routine the part creating the
cores. On Power9, we will need to create the cores after the Xive
interrupt controller is created.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This moves some code out from spapr_cpu_core_realize() for clarity. No
functional change.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The spapr_realize_vcpu() function doesn't rollback in case of error.
This isn't a problem with coldplugged CPUs because the machine won't
start and QEMU will exit. Hotplug is a different story though: the
CPU thread is started under object_property_set_bool() and it assumes
it can access the CPU object.
If icp_create() fails, we return an error without unregistering the
reset handler for this CPU, and we let the underlying QEMU thread for
this CPU alive. Since spapr_cpu_core_realize() doesn't care to unrealize
already realized CPUs either, but happily frees all of them anyway, the
CPU thread crashes instantly:
(qemu) device_add host-spapr-cpu-core,core-id=1,id=gku
GKU: failing icp_create (cpu 0x11497fd0)
^^^^^^^^^^
Program received signal SIGSEGV, Segmentation fault.
[Switching to Thread 0x7fffee3feaa0 (LWP 24725)]
0x00000000104c8374 in object_dynamic_cast_assert (obj=0x11497fd0,
^^^^^^^^^^^^^^
pointer to the CPU object
623 trace_object_dynamic_cast_assert(obj ? obj->class->type->name
(gdb) p obj->class->type
$1 = (Type) 0x0
(gdb) p * obj
$2 = {class = 0x10ea9c10, free = 0x11244620,
^^^^^^^^^^
should be g_free
(gdb) p g_free
$3 = {<text variable, no debug info>} 0x7ffff282bef0 <g_free>
obj is a dangling pointer to the CPU that was just destroyed in
spapr_cpu_core_realize().
This patch adds proper rollback to both spapr_realize_vcpu() and
spapr_cpu_core_realize().
Signed-off-by: Greg Kurz <groug@kaod.org>
[dwg: Fixed a conflict due to a change in my tree]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Commit 94ad93bd97684 (QEMU 2.12) switched to instantiate CPUs separately
but it missed to adapt the error path accordingly. If something fails in
the CPU creation loop, then the CPU object that was just created is leaked.
The error paths in this function are a bit obfuscated, and adding
yet another label to free this CPU object makes it worse. We should
move the block of the loop to a separate function, with a proper
rollback path, but this is a bigger cleanup.
For now, let's just fix the bug by adding the missing calls to
object_unref(). This will allow easier backport to older QEMU
versions.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Because this is the preferred practice in QEMU.
Signed-off-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Currently we don't have any unrealize path for pnv cpu cores. We get away
with this because we don't yet support cpu hotplug for pnv.
However, we're going to want it eventually, and in the meantime, it makes
it non-obvious why there are a bunch of allocations on the realize() path
that don't have matching frees.
So, implement the missing unrealize path.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
|
|
pnv_cpu_init() is only called from the the pnv cpu core realize path, and
really only can be called from there. So fold it into its caller, which
we also rename for brevity.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
|
|
Currently, we allocate space for all the cpu objects within a single core
in one big block. This was copied from an older version of the spapr code
and requires some ugly pointer manipulation to extract the individual
objects.
This design was due to a misunderstanding of qemu lifetime conventions and
has already been changed in spapr (in 94ad93bd "spapr_cpu_core: instantiate
CPUs separately".
Make an equivalent change in pnv_core to get rid of the nasty pointer
arithmetic.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
|
