| Age | Commit message (Collapse) | Author |
|---|
|
The POWER9 processor does not support per-core frequency control. The
cores are arranged in groups of four, along with their respective L2
and L3 caches, into a structure known as a Quad. The frequency must be
managed at the Quad level.
Provide a basic Quad model to fake the settings done by the firmware
on the Non-Cacheable Unit (NCU). Each core pair (EX) needs a special
BAR setting for the TIMA area of XIVE because it resides on the same
address on all chips.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-12-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The OCC on POWER9 is very similar to the one found on POWER8. Provide
the same routines with P9 values for the registers and IRQ number.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-10-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
To ease the introduction of the OCC model for POWER9, provide a new
class attributes to define XSCOM operations per CPU family and a PSI
IRQ number.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190307223548.20516-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The LPC Controller on POWER9 is very similar to the one found on
POWER8 but accesses are now done via on MMIOs, without the XSCOM and
ECCB logic. The device tree is populated differently so we add a
specific POWER9 routine for the purpose.
SerIRQ routing is yet to be done.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The ISA bus has a different DT nodename on POWER9. Compute the name
when the PnvChip is realized, that is before it is used by the machine
to populate the device tree with the ISA devices.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
It will ease the introduction of the LPC Controller model for POWER9.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20190307223548.20516-5-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The PSI bridge on POWER9 is very similar to POWER8. The BAR is still
set through XSCOM but the controls are now entirely done with MMIOs.
More interrupts are defined and the interrupt controller interface has
changed to XIVE. The POWER9 model is a first example of the usage of
the notify() handler of the XiveNotifier interface, linking the PSI
XiveSource to its owning device model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
To ease the introduction of the PSI bridge model for POWER9, abstract
the POWER chip differences in a PnvPsi class model and introduce a
specific Pnv8Psi type for POWER8. POWER8 interface to the interrupt
controller is still XICS whereas POWER9 uses the new XIVE model.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190307223548.20516-2-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The POWER9 and POWER8 processors have different interrupt controllers,
and reporting their state requires calling different helper routines.
However, the interrupt presenters are still handled in the higher
level pic_print_info() routine because they are not related to the
chip.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-9-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The POWER9 and POWER8 processors have a different set of devices and a
different device tree layout.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-8-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This is a simple model of the POWER9 XIVE interrupt controller for the
PowerNV machine which only addresses the needs of the skiboot
firmware. The PowerNV model reuses the common XIVE framework developed
for sPAPR as the fundamentals aspects are quite the same. The
difference are outlined below.
The controller initial BAR configuration is performed using the XSCOM
bus from there, MMIO are used for further configuration.
The MMIO regions exposed are :
- Interrupt controller registers
- ESB pages for IPIs and ENDs
- Presenter MMIO (Not used)
- Thread Interrupt Management Area MMIO, direct and indirect
The virtualization controller MMIO region containing the IPI ESB pages
and END ESB pages is sub-divided into "sets" which map portions of the
VC region to the different ESB pages. These are modeled with custom
address spaces and the XiveSource and XiveENDSource objects are sized
to the maximum allowed by HW. The memory regions are resized at
run-time using the configuration of EDT set translation table provided
by the firmware.
The XIVE virtualization structure tables (EAT, ENDT, NVTT) are now in
the machine RAM and not in the hypervisor anymore. The firmware
(skiboot) configures these tables using Virtual Structure Descriptor
defining the characteristics of each table : SBE, EAS, END and
NVT. These are later used to access the virtual interrupt entries. The
internal cache of these tables in the interrupt controller is updated
and invalidated using a set of registers.
Still to address to complete the model but not fully required is the
support for block grouping. Escalation support will be necessary for
KVM guests.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-7-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The POWER9 PowerNV machine will use a XIVE interrupt presenter type.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-6-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
We will use it to get the CPU interrupt presenter in XIVE when the
TIMA is accessed from the indirect page.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20190306085032.15744-3-clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Using IEC binary prefixes from qemu/units.h provides a more human-friendly value
to size constants.
Suggested-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Message-Id: <20190225170155.1972-4-muriloo@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The current 0x10000000 value is actually 256MiB, not 128MB as the comment
suggests. Move it to a constant and fix the comment (no change in the size
value).
Signed-off-by: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Message-Id: <20190225170155.1972-3-muriloo@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Building kernel with CONFIG_DEBUG_INFO_REDUCED can generate a ~90MB image and
building with CONFIG_DEBUG_INFO can generate a ~225M one, both exceeds the
current limit of 32MiB.
Increasing kernel size limit to 256MiB should fit for now.
Signed-off-by: Murilo Opsfelder Araujo <muriloo@linux.ibm.com>
Message-Id: <20190225170155.1972-2-muriloo@linux.ibm.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Both functions, object_initialize() and object_property_add_child() increase
the reference counter of the new object, so one of the references has to be
dropped afterwards to get the reference counting right. Otherwise the child
object will not be properly cleaned up when the parent gets destroyed.
Thus let's use now object_initialize_child() instead to get the reference
counting here right.
Suggested-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1550748288-30598-1-git-send-email-thuth@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Include the interrupt presenter under the machine_data as we plan to
remove it from under PowerPCCPU
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Now that the 'intc' pointer is only used by the XICS interrupt mode,
let's make things clear and use a XICS type and name.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Today, the interrupt presenter is linked to a CPU using the
cpu_intc_create() method of the sPAPR IRQ backend. The resulting
object is assigned to the PowerPCCPU 'intc' pointer whatever the
interrupt mode, XICS or XIVE.
To support the 'dual' interrupt mode, we will need to distinguish
between the two presenter objects and for that, we plan to introduce a
second interrupt presenter object pointer under the PowerPCCPU. The
modifications below move the assignment of the presenter object under
the cpu_intc_create() method to prepare ground for the future changes.
Both sPAPR and PowerNV machines are impacted.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
These files don't use anything exposed by "qemu/cutils.h",
simplify preprocessing including directly "qemu/units.h".
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au> (ppc parts)
Message-Id: <20180625124238.25339-7-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Code change produced with:
$ git ls-files | egrep '\.[ch]$' | \
xargs sed -i -e 's/\(\W[KMGTPE]\)_BYTE/\1iB/g'
Suggested-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au> (ppc parts)
Message-Id: <20180625124238.25339-6-f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The device tree node of the ISA bus was being partially done in
different places. Move all the nodes creation under the same routine.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
It introduces a base PnvChip class from which the specific processor
chip classes, Pnv8Chip and Pnv9Chip, inherit. Each of them needs to
define an init and a realize routine which will create the controllers
of the target processor. For the moment, the base PnvChip class
handles the XSCOM bus and the cores.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This moves the details of the ISA bus creation under the LPC model but
more important, the new PnvChip operation will let us choose the chip
class to use when we introduce the different chip classes for Power9
and Power8. It hides away the processor chip controllers from the
machine.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
On Power9, the thread interrupt presenter has a different type and is
linked to the chip owning the cores.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This extracts from the PvChip realize routine the part creating the
cores. On Power9, we will need to create the cores after the Xive
interrupt controller is created.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Currently, we allocate space for all the cpu objects within a single core
in one big block. This was copied from an older version of the spapr code
and requires some ugly pointer manipulation to extract the individual
objects.
This design was due to a misunderstanding of qemu lifetime conventions and
has already been changed in spapr (in 94ad93bd "spapr_cpu_core: instantiate
CPUs separately".
Make an equivalent change in pnv_core to get rid of the nasty pointer
arithmetic.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
|
|
The env->slb_nr field gives the size of the SLB (Segment Lookaside Buffer).
This is another static-after-initialization parameter of the specific
version of the 64-bit hash MMU in the CPU. So, this patch folds the field
into PPCHash64Options with the other hash MMU options.
This is a bit more complicated that the things previously put in there,
because slb_nr was foolishly included in the migration stream. So we need
some of the usual dance to handle backwards compatible migration.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
|
|
Currently env->mmu_model is a bit of an unholy mess of an enum of distinct
MMU types, with various flag bits as well. This makes which bits of the
field should be compared pretty confusing.
Make a start on cleaning that up by moving two of the flags bits -
POWERPC_MMU_1TSEG and POWERPC_MMU_AMR - which are specific to the 64-bit
hash MMU into a new flags field in PPCHash64Options structure.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
|
|
As a rule we prefer to pass PowerPCCPU instead of CPUPPCState, and this
change will make some things simpler later on.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
|
|
The ISA serial port handling in serial-isa.c imposes a limit
of 4 serial ports. This is because we only know of 4 IO port
and IRQ settings for them, and is unrelated to the generic
MAX_SERIAL_PORTS limit, though they happen to both be set at
4 currently.
Use a new MAX_ISA_SERIAL_PORTS wherever that is the correct
limit to be checking against.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180420145249.32435-11-peter.maydell@linaro.org
|
|
When skiboot starts, it first clears the CPU structs for all possible
CPUs on a system :
for (i = 0; i <= cpu_max_pir; i++)
memset(&cpu_stacks[i].cpu, 0, sizeof(struct cpu_thread));
On POWER9, cpu_max_pir is quite big, 0x7fff, and the skiboot cpu_stacks
array overlaps with the memory region in which QEMU maps the initramfs
file. Move it upwards in memory to keep it safe.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The XSCOM base address of the core chiplet was wrongly calculated. Use
the OPAL macros to fix that and do a couple of renames.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
When addressed by XSCOM, the first core has the 0x20 chiplet ID but
the CPU PIR can start at 0x0.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
commit 1ed9c8af501f ("target/ppc: Add POWER9 DD2.0 model information")
deprecated the POWER9 model v1.0.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The 'pnv' prefix is now used for all and the routines populating the
device tree start with 'pnv_dt'. The handler of the PnvXScomInterface
is also renamed to 'dt_xscom' which should reflect that it is
populating the device tree under the 'xscom@' node of the chip.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
Use a new DEFINE_TYPES() helper to simplify type registration
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
deduce core type directly from chip type instead of
maintaining type mapping in PnvChipClass::cpu_model.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
typically for cpus/core type names following convention is used
new_type_prefix-superclass_typename
make PNV core/chip to follow common convention.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
use common cpu_model prasing in vl.c and set default cpu_model
using generic MachineClass::default_cpu_type.
Beside of switching to generic infrastructure it solves several
issues.
* ppc_cpu_class_by_name() is used to deal with lower/upper case
and alias translations into actual cpu type, which fixes
'-M powernv -cpu power8' and '-M powernv -cpu power9_v1.0'
usecases which error out with:
'invalid CPU model 'FOO' for powernv machine'
* allows to switch to lower-case typenames in pnv chip/core name
(by convention typnames should be lower-case)
* replace aliased names /power8, power9, .../ with exact cpu model
names (i.e. typenames should be stable but aliases might decide to
point to other cpu model withi family or changed by kvm). It will
also help to simplify pnv_chip/core code and get rid of dependency
on cpu_model parsing.
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
[dwg: Updated to make DD2.0 as default POWER9 chip]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The offset of the root node is guaranteed to be 0.
This doesn't fix anything, it's just trivial cleanup of the two
remaining places where this was done under hw/ppc.
Signed-off-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Daniel Henrique Barboza <danielhb@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
and exit before uselessly trying to load it if the file does not
exists.
Issue discovered by Coverity Scan.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Convert all uses of error_report("warning:"... to use warn_report()
instead. This helps standardise on a single method of printing warnings
to the user.
All of the warnings were changed using these two commands:
find ./* -type f -exec sed -i \
's|error_report(".*warning[,:] |warn_report("|Ig' {} +
Indentation fixed up manually afterwards.
The test-qdev-global-props test case was manually updated to ensure that
this patch passes make check (as the test cases are case sensitive).
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Suggested-by: Thomas Huth <thuth@redhat.com>
Cc: Jeff Cody <jcody@redhat.com>
Cc: Kevin Wolf <kwolf@redhat.com>
Cc: Max Reitz <mreitz@redhat.com>
Cc: Ronnie Sahlberg <ronniesahlberg@gmail.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Lieven <pl@kamp.de>
Cc: Josh Durgin <jdurgin@redhat.com>
Cc: "Richard W.M. Jones" <rjones@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Cc: Greg Kurz <groug@kaod.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Peter Chubb <peter.chubb@nicta.com.au>
Cc: Eduardo Habkost <ehabkost@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Igor Mammedov <imammedo@redhat.com>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Alexander Graf <agraf@suse.de>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Cornelia Huck <cohuck@redhat.com>
Cc: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Greg Kurz <groug@kaod.org>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed by: Peter Chubb <peter.chubb@data61.csiro.au>
Acked-by: Max Reitz <mreitz@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Message-Id: <e1cfa2cd47087c248dd24caca9c33d9af0c499b0.1499866456.git.alistair.francis@xilinx.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
|
|
Use the actual unsigned integer type name.
The type name change impacts the following externally visible area:
* vl.c's machine_help_func() puts it in help for -machine NAME,help.
* QMP command qom-list exposes it in ObjectPropertyInfo member @type.
* QMP command device-list-properties exposes it in DevicePropertyInfo
member @type.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <20170607163635.17635-15-marcandre.lureau@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
|
|
Signed-off-by: Cédric Le Goater <clg@kaod.org>
[dwg: Correct typo in commit message]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
ppc patch queue for 2017-05-11
This pull request supersedes the one from yesterday (20170510), fixing
an important style bug in one patch, and adding an extra couple of
simple patches.
Highlights of this set:
* Some fixes for POWER9
* TCG support for POWER9 radix MMU
* VGA rom for Mac machine types
* Fixes for the XICS interrupt controller
* MTTCG support for ppc targets
As suggested by Paolo, I've tried to add the Docker tests to my
standard pre-pull-request tests. I haven't wholly suceeded; this has
been tested with some of the Docker images, but others I haven't
managed due to problems that as best I can tell are not due to
problems in this patch series. I'll continue working on this for
future pull requests. Specifically, 'travis', 'fedora', and 'centos6'
seem to work. 'min-glib' jammed while gtesting moxie, which seems
very unlikely to be caused by this series. 'ubuntu', 'debian' and
'debian-bootstrap' hit build errors almost immediately that look like
problems with the container configuration, and 'debian-*-cross' hit
build errors later on which also look like missing dependencies from
the container.
# gpg: Signature made Thu 11 May 2017 05:13:46 AM BST
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* dgibson/tags/ppc-for-2.10-20170511: (23 commits)
target/ppc: Avoid printing wrong aliases in CPU help text
pnv: Fix build failures on some host platforms
target/ppc: Allow workarounds for POWER9 DD1
spapr: Don't accidentally advertise HTM support on POWER9
ppc: xics: fix compilation with CentOS 6
target/ppc: Enable RADIX mmu mode for pseries TCG guest
target/ppc: Implement ISA V3.00 radix page fault handler
target/ppc: Change tlbie invalid fields for POWER9 support
target/ppc: Update tlbie to check privilege level based on GTSE
target/ppc: Set UPRT and GTSE on all cpus in H_REGISTER_PROCESS_TABLE
ppc: add qemu_vga.ndrv ROM to fw_cfg interface for NewWorld Macs
ppc: add qemu_vga.ndrv ROM to fw_cfg interface for OldWorld Macs
Add QemuMacDrivers qemu_vga.ndrv revision d4e7d7a built as submodule
Add QemuMacDrivers as submodule
ppc/xics: preserve P and Q bits for KVM IRQs
ppc/xics: Fix stale irq->status bits after get
target/ppc: do not reset reserve_addr in exec_enter
tcg: enable MTTCG by default for PPC64 on x86
cpus: Fix CPU unplug for MTTCG
target/ppc: Generate fence operations
...
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
Today, when a PowerNV guest runs, it uses the sensor definitions of
the BMC simulator to populate the device tree. But an external IPMI
BMC could also be used and, in that case, it is not (yet) possible to
retrieve the sensor list. Generating the OEM SEL event for shutdown or
reboot also does not make sense as it should be generated on the BMC
side.
This change allows a guest to use an 'ipmi-bmc-extern' backend to the
'isa-ipmi-bt' device and a 'chardev' for transport such as :
-chardev socket,id=ipmi0,host=localhost,port=9002,reconnect=10 \
-device ipmi-bmc-extern,id=bmc0,chardev=ipmi0 \
-device isa-ipmi-bt,bmc=bmc0,irq=10
and connect to a BMC simulator, the OpenIPMI ipmi_sim simulator for
instance.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This patch removes redundant "qemu:" from error functions. The link to the bitesized task is:
http://wiki.qemu-project.org/Contribute/BiteSizedTasks#Error_checking
Signed-off-by: Ishani Chugh <chugh.ishani@research.iiit.ac.in>
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
