| Age | Commit message (Collapse) | Author |
|---|
|
To indicate Cadence GEM not Xilinx.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
into staging
migration/next for 20140515
# gpg: Signature made Thu 15 May 2014 02:32:25 BST using RSA key ID 5872D723
# gpg: Can't check signature: public key not found
* remotes/juanquintela/tags/migration/20140515:
usb: fix up post load checks
migration: show average throughput when migration finishes
savevm: Remove all the unneeded version_minimum_id_old (rest)
savevm: Remove all the unneeded version_minimum_id_old (usb)
Split ram_save_block
arch_init: Simplify code for load_xbzrle()
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
After previous Peter patch, they are redundant. This way we don't
assign them except when needed. Once there, there were lots of case
where the ".fields" indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (appart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Commit 191946c moved the code to handle padding to minimum
length from after the handling of the CRC to before it.
This means that the CRC code doesn't need to cope with the
possibility that the size is less than 60; remove this
dead code.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
|
|
Convert this device to use vmstate for its save/load, including
providing a post_load function that sanitizes inbound data to
avoid possible buffer overflows if it is malicious.
The sanitizing fixes CVE-2013-4532 (though nobody should be
relying on the security properties of most of the unmaintained
ARM board models anyway, and migration doesn't actually
work on this board due to issues in other device models).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The rx_fifo pointer is awkward to migrate, and is actually
redundant since it is always possible to determine it from
the current rx[].len/.data and rx_fifo_len. Remove both
rx_fifo and rx_fifo_len from the state, replacing them with
a simple rx_fifo_offset which points at the current location
in the RX fifo.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
|
|
Fix various debug format strings which were incorrect for the
data type, so that building with debug enabled is possible.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
|
|
Packet transmission for the stellaris ethernet controller can be triggered
in one of two ways:
* by setting a threshold value in the THR register; when the FIFO
fill level reaches the threshold, the h/w starts transmitting.
Software has to finish filling the FIFO before the transmit
process completes to avoid a (silent) underrun
* by software writing to the TR register to explicitly trigger
transmission
Since QEMU transmits packets instantaneously (from the guest's
point of view), implement "transmit based on threshold" with
our existing mechanism of "transmit as soon as we have the whole
packet", with the additional wrinkle that we don't transmit if
the packet size is below the specified threshold, and implement
"transmit by specific request" properly.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
|
|
The datasheet is clear that the frame length written to the DATA
register is actually stored in the TX FIFO; this means we don't
need to keep both tx_frame_len and tx_fifo_len state separately.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
|
|
The PADEN bit in the transmit control register enables padding of short
data packets out to the required minimum length. However a typo here
meant we were adjusting tx_fifo_len rather than tx_frame_len, so the
padding didn't actually happen. Fix this bug.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: qemu-stable@nongnu.org
|
|
The current tx_fifo code has a corner case where the guest can overrun
the fifo buffer: if automatic CRCs are disabled we allow the guest to write
the CRC word even if there isn't actually space for it in the FIFO.
The datasheet is unclear about exactly how the hardware deals with this
situation; the most plausible answer seems to be that the CRC word is
just lost.
Implement this fix by separating the "can we stuff another word in the
FIFO" logic from the "should we transmit the packet now" check. This
also moves us closer to the real hardware, which has a number of ways
it can be configured to trigger sending the packet, some of which we
don't implement.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: qemu-stable@nongnu.org
|
|
After commit 767adce2d, they are redundant. This way we don't assign them
except when needed. Once there, there were lots of cases where the ".fields"
indentation was wrong:
.fields = (VMStateField []) {
and
.fields = (VMStateField []) {
Change all the combinations to:
.fields = (VMStateField[]){
The biggest problem (apart from aesthetics) was that checkpatch complained
when we copy&pasted the code from one place to another.
Signed-off-by: Juan Quintela <quintela@redhat.com>
[PMM: fixed minor conflict, corrected commit message typos]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
This fixes warnings from the static code analysis (smatch).
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
into staging
migration/next for 20140505
# gpg: Signature made Mon 05 May 2014 21:27:24 BST using RSA key ID 5872D723
# gpg: Can't check signature: public key not found
* remotes/juanquintela/tags/migration/20140505: (36 commits)
migration: expose xbzrle cache miss rate
migration: expose the bitmap_sync_count to the end
migration: Add counts of updating the dirty bitmap
XBZRLE: Fix one XBZRLE corruption issues
migration: remove duplicate code
Coverity: Fix failure path for qemu_accept in migration
Init the XBZRLE.lock in ram_mig_init
Provide init function for ram migration
Count used RAMBlock pages for migration_dirty_pages
Make qemu_peek_buffer loop until it gets it's data
Disallow outward migration while awaiting incoming migration
virtio: validate config_len on load
virtio-net: out-of-bounds buffer write on load
openpic: avoid buffer overrun on incoming migration
ssi-sd: fix buffer overrun on invalid state load
savevm: Ignore minimum_version_id_old if there is no load_state_old
usb: sanity check setup_index+setup_len in post_load
vmstate: s/VMSTATE_INT32_LE/VMSTATE_INT32_POSITIVE_LE/
virtio-scsi: fix buffer overrun on invalid state load
zaurus: fix buffer overrun on invalid state load
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
CVE-2013-4149 QEMU 1.3.0 out-of-bounds buffer write in
virtio_net_load()@hw/net/virtio-net.c
> } else if (n->mac_table.in_use) {
> uint8_t *buf = g_malloc0(n->mac_table.in_use);
We are allocating buffer of size n->mac_table.in_use
> qemu_get_buffer(f, buf, n->mac_table.in_use * ETH_ALEN);
and read to the n->mac_table.in_use size buffer n->mac_table.in_use *
ETH_ALEN bytes, corrupting memory.
If adversary controls state then memory written there is controlled
by adversary.
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
|
|
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
CVE-2013-4150 QEMU 1.5.0 out-of-bounds buffer write in
virtio_net_load()@hw/net/virtio-net.c
This code is in hw/net/virtio-net.c:
if (n->max_queues > 1) {
if (n->max_queues != qemu_get_be16(f)) {
error_report("virtio-net: different max_queues ");
return -1;
}
n->curr_queues = qemu_get_be16(f);
for (i = 1; i < n->curr_queues; i++) {
n->vqs[i].tx_waiting = qemu_get_be32(f);
}
}
Number of vqs is max_queues, so if we get invalid input here,
for example if max_queues = 2, curr_queues = 3, we get
write beyond end of the buffer, with data that comes from
wire.
This might be used to corrupt qemu memory in hard to predict ways.
Since we have lots of function pointers around, RCE might be possible.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
|
|
into staging
trivial patches for 2014-04-28
# gpg: Signature made Mon 28 Apr 2014 05:56:01 BST using RSA key ID A4C3D7DB
# gpg: Good signature from "Michael Tokarev <mjt@tls.msk.ru>"
# gpg: aka "Michael Tokarev <mjt@corpit.ru>"
# gpg: aka "Michael Tokarev <mjt@debian.org>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6EE1 95D1 886E 8FFB 810D 4324 457C E0A0 8044 65C5
# Subkey fingerprint: 6F67 E18E 7C91 C5B1 5514 66A7 BEE5 9D74 A4C3 D7DB
* remotes/mjt/tags/trivial-patches-2014-04-28:
slirp/smb: Move ncalrpc directory to tmp
po: add proper Language: tags to .po files
po/Makefile: fix $SRC_PATH reference
init_paths: fix minor memory leak
virtfs-proxy-helper: fix call to accept
net/net.c: remove unnecessary semicolon
Add QEMU logo (SVG file)
vl: avoid closing stdout with 'writeconfig'
xilinx: Fix typo in comment (Marvel -> Marvell)
vl: Eliminate a superfluous local variable
vl: Remove useless 'continue'
gitignore: cleanups #2
tests/.gitignore: Ignore test-rfifolock
move test-* from .gitignore to tests/.gitignore
configure: Improve help behavior
vl: convert -m to QemuOpts
qemu-option: introduce qemu_find_opts_singleton
misc: Use cpu_physical_memory_read and cpu_physical_memory_write
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
Clear the BMCR Reset when writing to registers.
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
[ PC:
* Trivial style fixes to commit message
]
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
Signed-off-by: Prasad Joshi <prasadjoshi.linux@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
Phys must respond to address 0 by specification. Implement.
Signed-off-by: Nathan Rossi <nathan.rossi@xilinx.com>
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 6f4d53b04ddbfb19895bfb61a595e69f1c08859a.1396594056.git.peter.crosthwaite@xilinx.com
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The irq line status must be updated after writes to the INT_CTL and
INT_STA registers.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 1395771730-16882-8-git-send-email-b.galvani@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Message-id: 1395771730-16882-7-git-send-email-b.galvani@gmail.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
CVE-2013-4544
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 1396604722-11902-5-git-send-email-dmitry@daynix.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
CVE-2013-4544
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 1396604722-11902-4-git-send-email-dmitry@daynix.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
CVE-2013-4544
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 1396604722-11902-3-git-send-email-dmitry@daynix.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
CVE-2013-4544
Signed-off-by: Dmitry Fleytman <dmitry@daynix.com>
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 1396604722-11902-2-git-send-email-dmitry@daynix.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
When VM guest programs multicast addresses for
a virtio net card, it supplies a 32 bit
entries counter for the number of addresses.
These addresses are read into tail portion of
a fixed macs array which has size MAC_TABLE_ENTRIES,
at offset equal to in_use.
To avoid overflow of this array by guest, qemu attempts
to test the size as follows:
- if (in_use + mac_data.entries <= MAC_TABLE_ENTRIES) {
however, as mac_data.entries is uint32_t, this sum
can overflow, e.g. if in_use is 1 and mac_data.entries
is 0xffffffff then in_use + mac_data.entries will be 0.
Qemu will then read guest supplied buffer into this
memory, overflowing buffer on heap.
CVE-2014-0150
Cc: qemu-stable@nongnu.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Message-id: 1397218574-25058-1-git-send-email-mst@redhat.com
Reviewed-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Stefan Fritsch just fixed a virtio-net driver bug [1], virtio-net won't
filter out VLAN-tagged packets if VIRTIO_NET_F_CTRL_VLAN isn't negotiated.
This patch added a new field to @RxFilterInfo to indicate vlan receive
state ('normal', 'none', 'all'). If VIRTIO_NET_F_CTRL_VLAN isn't
negotiated, vlan receive state will be 'all', then all VLAN-tagged packets
will be received by guest.
This patch also fixed a boundary issue in visiting vlan table.
[1] http://lists.nongnu.org/archive/html/qemu-devel/2014-02/msg02604.html
Signed-off-by: Amos Kong <akong@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
|
|
If VIRTIO_NET_F_CTRL_VLAN is not negotiated, do not filter out all
VLAN-tagged packets but send them to the guest.
This fixes VLANs with OpenBSD guests (and probably NetBSD, too, because
the OpenBSD driver started as a port from NetBSD).
Signed-off-by: Stefan Fritsch <sf@sfritsch.de>
Signed-off-by: Amos Kong <akong@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
PowerPC queue for 2.0
* sPAPR loop fix
* SPR reset fix
* Reduce allocation size of indirect opcode tables
* Restrict number of CPU threads
* sPAPR H_SET_MODE fixes
* sPAPR firmware path fixes
* Static and constness cleanups
# gpg: Signature made Thu 20 Mar 2014 01:46:14 GMT using RSA key ID 3E7E013F
# gpg: Good signature from "Andreas Färber <afaerber@suse.de>"
# gpg: aka "Andreas Färber <afaerber@suse.com>"
* remotes/afaerber/tags/ppc-for-2.0:
spapr: Implement interface to fix device pathname
spapr: QOM'ify pseries machine
spapr_vio: Fix firmware names
spapr_llan: Add to boot device list
qdev: Introduce FWPathProvider interface
vl.c: Extend get_boot_devices_list() to ignore suffixes
spapr_hcall: Fix little-endian resource handling in H_SET_MODE
target-ppc: Introduce powerisa-207-server flag
target-ppc: Force CPU threads count to be a power of 2
target-ppc: Fix overallocation of opcode tables
target-ppc: Reset SPRs on CPU reset
spapr_hcall: Fix h_enter to loop correctly
target-ppc: Add missing 'static' and 'const' attributes
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
There are currently three types of object_property_add_link() callers:
1. The link property may be set at any time.
2. The link property of a DeviceState instance may only be set before
realize.
3. The link property may never be set, it is read-only.
Something similar can already be achieved with
object_property_add_str()'s set() argument. Follow its example and add
a check() argument to object_property_add_link().
Also provide default check() functions for case #1 and #2. Case #3 is
covered by passing a NULL function pointer.
Cc: Peter Crosthwaite <peter.crosthwaite@petalogix.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Anthony Liguori <aliguori@amazon.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
[AF: Tweaked documentation comment]
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Some object_property_add_link() callers expect property deletion to
unref the link property object. Other callers expect to manage the
refcount themselves. The former are currently broken and therefore leak
the link property object.
This patch adds a flags argument to object_property_add_link() so the
caller can specify which refcount behavior they require. The new
OBJ_PROP_LINK_UNREF_ON_RELEASE flag causes the link pointer to be
unreferenced when the property is deleted.
This fixes refcount leaks in qdev.c, xilinx_axidma.c, xilinx_axienet.c,
s390-virtio-bus.c, virtio-pci.c, virtio-rng.c, and ui/console.c.
Rationale for refcount behavior:
* hw/core/qdev.c
- bus children are explicitly unreferenced, don't interfere
- parent_bus is essentially a read-only property that doesn't hold a
refcount, don't unref
- hotplug_handler is leaked, do unref
* hw/dma/xilinx_axidma.c
- rx stream "dma" links are set using set_link, therefore they
need unref
- tx streams are set using set_link, therefore they need unref
* hw/net/xilinx_axienet.c
- same reasoning as hw/dma/xilinx_axidma.c
* hw/pcmcia/pxa2xx.c
- pxa2xx bypasses set_link and therefore does not use refcounts
* hw/s390x/s390-virtio-bus.c
* hw/virtio/virtio-pci.c
* hw/virtio/virtio-rng.c
* ui/console.c
- set_link is used and there is no explicit unref, do unref
Cc: Peter Crosthwaite <peter.crosthwaite@petalogix.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Anthony Liguori <aliguori@amazon.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Signed-off-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
Codespell found and fixed these new typos:
* doesnt -> doesn't
* funtion -> function
* perfomance -> performance
* remaing -> remaining
A coding style issue (line too long) was fixed manually.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
peer_{de,at}tach were called from inside assert().
We don't support building without NDEBUG but it's not tidy.
Rearrange to attach peer outside assert calls.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
When the guests adds buffers to receive queue, the network device
should flush its queue of pending packets. This is done with
qemu_flush_queued_packets.
This adds a call to qemu_flush_queued_packets() which wakes up the main
loop and let QEMU update the network device status which now is "can
receive". The patch basically does the same thing as e8b4c68 does.
Suggested-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
This implementation doesn't include ring priority, TCP/IP Off-Load, QoS.
Signed-off-by: Fabien Chouteau <chouteau@adacore.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
|
|
'remotes/pmaydell/tags/pull-target-arm-20140226' into staging
target-arm queue:
* fixes for various Coverity-spotted bugs
* support new KVM device control API for VGIC
* support KVM VGIC save/restore/migration
* more AArch64 system mode foundations
* support ARMv8 CRC instructions for A32/T32
* PL330 minor fixes and cleanup
# gpg: Signature made Wed 26 Feb 2014 17:51:32 GMT using RSA key ID 14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
* remotes/pmaydell/tags/pull-target-arm-20140226: (45 commits)
dma/pl330: implement dmaadnh instruction
dma/pl330: Fix buffer depth
dma/pl330: Add event debugging printfs
dma/pl330: Rename parent_obj
dma/pl330: printf format type sweep.
dma/pl330: Fix misleading type
dma/pl330: Delete overly verbose debug printf
target-arm: Add support for AArch32 ARMv8 CRC32 instructions
include/qemu/crc32c.h: Rename include guards to match filename
target-arm: Add utility function for checking AA32/64 state of an EL
target-arm: Implement AArch64 view of CPACR
target-arm: A64: Implement MSR (immediate) instructions
target-arm: Store AIF bits in env->pstate for AArch32
target-arm: A64: Implement WFI
target-arm: Get MMU index information correct for A64 code
target-arm: Implement AArch64 OSLAR_EL1 sysreg as WI
target-arm: Implement AArch64 dummy breakpoint and watchpoint registers
target-arm: Implement AArch64 ID and feature registers
target-arm: Implement AArch64 generic timers
target-arm: Implement AArch64 MPIDR
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add a cast to avoid an unintended sign extension that
would mean we returned 0xffffffff in the high 32 bits
for an IA0 read if bit 31 in the MAC address was 1.
(This is harmless since we'll only be doing 4 byte
reads, but it could be confusing, so best avoided.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Message-id: 1392647854-8067-3-git-send-email-peter.maydell@linaro.org
|
|
qemu_get_queue() is a shorthand for qemu_get_subqueue(n->nic, 0). Use
the shorthand where possible.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
There is no need to access backend->info->has_vnet_hdr() and friends
anymore. Use the qemu_has_vnet_hdr() API instead.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
The virtio_net offload APIs are used on the NIC's peer (i.e. the tap
device). The API was defined to implicitly use nc->peer, saving the
caller the trouble.
This wasn't ideal because:
1. There are callers who have the peer but not the NIC. Currently they
are forced to bypass the API and access peer->info->... directly.
2. The rest of the net.h API uses nc, not nc->peer, so it is
inconsistent.
This patch pushes nc->peer back up to callers.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
With this patch, virtio-net and vmxnet3 frontends make
use of the qemu_peer_* API for backend offloadings manipulations,
instead of calling TAP-specific functions directly.
We also remove the existing checks which prevent those frontends
from using offloadings with backends different from TAP (e.g. netmap).
Signed-off-by: Vincenzo Maffione <v.maffione@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
The following registers control whether MAC can receive frames:
- MODER.RXEN bit that enables/disables receiver;
- TX_BD_NUM register that specifies number of RX descriptors.
Notify QEMU networking core when the MAC is ready to receive frames.
Discard frame and raise BUSY interrupt when the frame arrives but the
current RX descriptor is not empty.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
The following registers control whether MAC can receive frames:
- MODER.RXEN bit that enables/disables receiver;
- TX_BD_NUM register that specifies number of RX descriptors.
Notify QEMU networking core when the MAC is ready to receive frames.
Discard frame and raise BUSY interrupt when the frame arrives but the
current RX descriptor is not empty.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Replace them with uint8/32/64.
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
|
