aboutsummaryrefslogtreecommitdiff
path: root/hw/net/e1000e_core.c
AgeCommit message (Collapse)Author
2023-05-23e1000e: Notify only new interruptsAkihiko Odaki
In MSI-X mode, if there are interrupts already notified but not cleared and a new interrupt arrives, e1000e incorrectly notifies the notified ones again along with the new one. To fix this issue, replace e1000e_update_interrupt_state() with two new functions: e1000e_raise_interrupts() and e1000e_lower_interrupts(). These functions don't only raise or lower interrupts, but it also performs register writes which updates the interrupt state. Before it performs a register write, these function determines the interrupts already raised, and compares with the interrupts raised after the register write to determine the interrupts to notify. The introduction of these functions made tracepoints which assumes that the caller of e1000e_update_interrupt_state() performs register writes obsolete. These tracepoints are now removed, and alternative ones are added to the new functions. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-05-23igb: Strip the second VLAN tag for extended VLANAkihiko Odaki
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-05-23igb: Implement Rx SCTP CSOAkihiko Odaki
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-05-23e1000e: Rename a variable in e1000e_receive_internal()Akihiko Odaki
Rename variable "n" to "causes", which properly represents the content of the variable. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-05-23e1000e: Reset packet state after emptying Tx queueAkihiko Odaki
Keeping Tx packet state after the transmit queue is emptied has some problems: - The datasheet says the descriptors can be reused after the transmit queue is emptied, but the Tx packet state may keep references to them. - The Tx packet state cannot be migrated so it can be reset anytime the migration happens. Always reset Tx packet state always after the queue is emptied. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-05-23e1000e: Always log status after building rx metadataAkihiko Odaki
Without this change, the status flags may not be traced e.g. if checksum offloading is disabled. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-05-23e1000x: Rename TcpIpv6 into TcpIpv6ExAkihiko Odaki
e1000e and igb employs NetPktRssIpV6TcpEx for RSS hash if TcpIpv6 MRQC bit is set. Moreover, igb also has a MRQC bit for NetPktRssIpV6Tcp though it is not implemented yet. Rename it to TcpIpv6Ex to avoid confusion. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-05-23e1000x: Share more Rx filtering logicAkihiko Odaki
This saves some code and enables tracepoint for e1000's VLAN filtering. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-05-23e1000e: Always copy ethernet headerAkihiko Odaki
e1000e_receive_internal() used to check the iov length to determine copy the iovs to a contiguous buffer, but the check is flawed in two ways: - It does not ensure that iovcnt > 0. - It does not take virtio-net header into consideration. The size of this copy is just 18 octets, which can be even less than the code size required for checks. This (wrong) optimization is probably not worth so just remove it. Fixes: 6f3fbe4ed0 ("net: Introduce e1000e device emulation") Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-05-23e1000x: Fix BPRC and MPRCAkihiko Odaki
Before this change, e1000 and the common code updated BPRC and MPRC depending on the matched filter, but e1000e and igb decided to update those counters by deriving the packet type independently. This inconsistency caused a multicast packet to be counted twice. Updating BPRC and MPRC depending on are fundamentally flawed anyway as a filter can be used for different types of packets. For example, it is possible to filter broadcast packets with MTA. Always determine what counters to update by inspecting the packets. Fixes: 3b27430177 ("e1000: Implementing various counters") Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Reviewed-by: Sriram Yagnaraman <sriram.yagnaraman@est.tech> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-05-23hw/net/net_tx_pkt: Decouple interface from PCIAkihiko Odaki
This allows to use the network packet abstractions even if PCI is not used. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-05-23e1000e: Fix tx/rx counterstimothee.cocault@gmail.com
The bytes and packets counter registers are cleared on read. Copying the "total counter" registers to the "good counter" registers has side effects. If the "total" register is never read by the OS, it only gets incremented. This leads to exponential growth of the "good" register. This commit increments the counters individually to avoid this. Signed-off-by: Timothée Cocault <timothee.cocault@gmail.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-28igb: Fix DMA requester specification for Tx packetAkihiko Odaki
igb used to specify the PF as DMA requester when reading Tx packets. This made Tx requests from VFs to be performed on the address space of the PF, defeating the purpose of SR-IOV. Add some logic to change the requester depending on the queue, which can be assigned to a VF. Fixes: 3a977deebe ("Intrdocue igb device emulation") Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10e1000: Split header filesAkihiko Odaki
Some definitions in the header files are invalid for igb so extract them to new header files to keep igb from referring to them. Signed-off-by: Gal Hammer <gal.hammer@sap.com> Signed-off-by: Marcel Apfelbaum <marcel.apfelbaum@gmail.com> Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10net/eth: Introduce EthL4HdrProtoAkihiko Odaki
igb, a new network device emulation, will need SCTP checksum offloading. Currently eth_get_protocols() has a bool parameter for each protocol currently it supports, but there will be a bit too many parameters if we add yet another protocol. Introduce an enum type, EthL4HdrProto to represent all L4 protocols eth_get_protocols() support with one parameter. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10e1000e: Implement system clockAkihiko Odaki
The system clock is necessary to implement PTP features. While we are not implementing PTP features for e1000e yet, we do have a plan to implement them for igb, a new network device derived from e1000e, so add system clock to the common base first. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10net/eth: Report if headers are actually presentAkihiko Odaki
The values returned by eth_get_protocols() are used to perform RSS, checksumming and segmentation. Even when a packet signals the use of the protocols which these operations can be applied to, the headers for them may not be present because of too short packet or fragmentation, for example. In such a case, the operations cannot be applied safely. Report the presence of headers instead of whether the use of the protocols are indicated with eth_get_protocols(). This also makes corresponding changes to the callers of eth_get_protocols() to match with its new signature and to remove redundant checks for fragmentation. Fixes: 75020a7021 ("Common definitions for VMWARE devices") Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10e1000e: Count CRC in Tx statisticsAkihiko Odaki
The datasheet 8.19.29 "Good Packets Transmitted Count - GPTC (0x04080; RC)" says: > This register counts the number of good (no errors) packets > transmitted. A good transmit packet is considered one that is 64 or > more bytes in length (from <Destination Address> through <CRC>, > inclusively) in length. It also says similar for the other Tx statistics registers. Add the number of bytes for CRC to those registers. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10e1000e: Combine rx tracesAkihiko Odaki
Whether a packet will be written back to the guest depends on the remaining space of the queue. Therefore, e1000e_rx_written_to_guest and e1000e_rx_not_written_to_guest should log the index of the queue instead of generated interrupts. This also removes the need of e1000e_rx_rss_dispatched_to_queue, which logs the queue index. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10e1000e: Do not assert when MSI-X is disabled laterAkihiko Odaki
Assertions will fail if MSI-X gets disabled while a timer for MSI-X interrupts is running so remove them to avoid abortions. Fortunately, nothing bad happens even if the assertions won't trigger as msix_notify(), called by timer handlers, does nothing when MSI-X is disabled. This bug was found by Alexander Bulekov when fuzzing igb, a new device implementation derived from e1000e: https://patchew.org/QEMU/20230129053316.1071513-1-alxndr@bu.edu/ The fixed test case is: fuzz/crash_aea040166819193cf9fedb810c6d100221da721a Fixes: 6f3fbe4ed0 ("net: Introduce e1000e device emulation") Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10e1000e: Perform software segmentation for loopbackAkihiko Odaki
e1000e didn't perform software segmentation for loopback if virtio-net header is enabled, which is wrong. To fix the problem, introduce net_tx_pkt_send_custom(), which allows the caller to specify whether offloading should be assumed or not. net_tx_pkt_send_custom() also allows the caller to provide a custom sending function. Packets with virtio-net headers and ones without virtio-net headers will be provided at the same time so the function can choose the preferred version. In case of e1000e loopback, it prefers to have virtio-net headers as they allows to skip the checksum verification if VIRTIO_NET_HDR_F_DATA_VALID is set. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10hw/net/net_rx_pkt: Remove net_rx_pkt_has_virt_hdrAkihiko Odaki
When virtio-net header is not set, net_rx_pkt_get_vhdr() returns zero-filled virtio_net_hdr, which is actually valid. In fact, tap device uses zero-filled virtio_net_hdr when virtio-net header is not provided by the peer. Therefore, we can just remove net_rx_pkt_has_virt_hdr() and always assume NetTxPkt has a valid virtio-net header. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10hw/net/net_tx_pkt: Automatically determine if virtio-net header is usedAkihiko Odaki
The new function qemu_get_using_vnet_hdr() allows to automatically determine if virtio-net header is used. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10net: Check L4 header sizeAkihiko Odaki
net_tx_pkt_build_vheader() inspects TCP header but had no check for the header size, resulting in an undefined behavior. Check the header size and drop the packet if the header is too small. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10e1000e: Remove extra pointer indirectionAkihiko Odaki
e1000e_write_packet_to_guest() passes the reference of variable ba as a pointer to an array, and that pointer indirection is just unnecessary; all functions which uses the passed reference performs no pointer operation on the pointer and they simply dereference the passed pointer. Remove the extra pointer indirection. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10e1000e: Set MII_ANER_NWAYAkihiko Odaki
This keeps Windows driver 12.18.9.23 from generating an event with ID 30. The description of the event is as follows: > Intel(R) 82574L Gigabit Network Connection > PROBLEM: The network adapter is configured for auto-negotiation but > the link partner is not. This may result in a duplex mismatch. > ACTION: Configure the link partner for auto-negotiation. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10e1000e: Introduce e1000_rx_desc_unionAkihiko Odaki
Before this change, e1000e_write_packet_to_guest() allocated the receive descriptor buffer as an array of uint8_t. This does not ensure the buffer is sufficiently aligned. Introduce e1000_rx_desc_union type, a union type of all receive descriptor types to correct this. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10e1000e: Improve software resetAkihiko Odaki
This change makes e1000e reset more things when software reset was triggered. Some registers are exempted from software reset in the datasheet and this change also implements the behavior accordingly. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10e1000e: Remove pending interrupt flagsAkihiko Odaki
They are duplicate of running throttling timer flags and incomplete as the flags are not cleared when the interrupts are fired or the device is reset. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10e1000e: Use memcpy to intialize registersAkihiko Odaki
Use memcpy instead of memmove to initialize registers. The initial register templates and register table instances will never overlap. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10e1000e: Use more constant definitionsAkihiko Odaki
The definitions of SW Semaphore Register were copied from: https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/tree/drivers/net/ethernet/intel/e1000e/defines.h?h=v6.0.9#n374 Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10e1000e: Mask registers when writingAkihiko Odaki
When a register has effective bits fewer than their width, the old code inconsistently masked when writing or reading. Make the code consistent by always masking when writing, and remove some code duplication. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10e1000e: Introduce E1000E_LOW_BITS_SET_FUNCAkihiko Odaki
e1000e_set_16bit and e1000e_set_12bit look so similar so define a generic macro. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10e1000: Use hw/net/mii.hAkihiko Odaki
hw/net/mii.h provides common definitions for MII. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Signed-off-by: Jason Wang <jasowang@redhat.com>
2023-03-10e1000e: Fix the code styleAkihiko Odaki
igb implementation first starts off by copying e1000e code. Correct the code style before that. Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Signed-off-by: Jason Wang <jasowang@redhat.com>
2022-09-27e1000e: set RX desc status with DD flag in a separate operationDing Hui
Like commit 034d00d48581 ("e1000: set RX descriptor status in a separate operation"), there is also same issue in e1000e, which would cause lost packets or stop sending packets to VM with DPDK. Do similar fix in e1000e. Resolves: https://gitlab.com/qemu-project/qemu/-/issues/402 Signed-off-by: Ding Hui <dinghui@sangfor.com.cn> Signed-off-by: Jason Wang <jasowang@redhat.com>
2022-09-22hw/net/e1000e_core: Use definition to avoid dynamic stack allocationPhilippe Mathieu-Daudé
The compiler isn't clever enough to figure 'min_buf_size' is a constant, so help it by using a definitions instead. Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com> Acked-by: Jason Wang <jasowang@redhat.com> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Message-id: 20220819153931.3147384-6-peter.maydell@linaro.org
2022-07-26e1000e: Fix possible interrupt loss when using MSIAke Koomsin
Commit "e1000e: Prevent MSI/MSI-X storms" introduced msi_causes_pending to prevent interrupt storms problem. It was tested with MSI-X. In case of MSI, the guest can rely solely on interrupts to clear ICR. Upon clearing all pending interrupts, msi_causes_pending gets cleared. However, when e1000e_itr_should_postpone() in e1000e_send_msi() returns true, MSI never gets fired by e1000e_intrmgr_on_throttling_timer() because msi_causes_pending is still set. This results in interrupt loss. To prevent this, we need to clear msi_causes_pending when MSI is going to get fired by the throttling timer. The guest can then receive interrupts eventually. Signed-off-by: Ake Koomsin <ake@igel.co.jp> Signed-off-by: Jason Wang <jasowang@redhat.com>
2022-02-14hw/net: e1000e: Clear ICR on read when using non MSI-X interruptsNick Hudson
In section 7.4.3 of the 82574 datasheet it states that "In systems that do not support MSI-X, reading the ICR register clears it's bits..." Some OSes rely on this. Signed-off-by: Nick Hudson <skrll@netbsd.org> Signed-off-by: Jason Wang <jasowang@redhat.com>
2021-08-02hw/net: e1000e: Don't zero out the VLAN tag in the legacy RX descriptorChristina Wang
In the legacy RX descriptor mode, VLAN tag was saved to d->special by e1000e_build_rx_metadata() in e1000e_write_lgcy_rx_descr(), but it was then zeroed out again at the end of the call, which is wrong. Fixes: c89d416a2b0f ("e1000e: Don't zero out buffer address in rx descriptor") Reported-by: Markus Carlstedt <markus.carlstedt@windriver.com> Signed-off-by: Christina Wang <christina.wang@windriver.com> Signed-off-by: Bin Meng <bin.meng@windriver.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2021-08-02hw/net: e1000e: Correct the initial value of VET registerChristina Wang
The initial value of VLAN Ether Type (VET) register is 0x8100, as per the manual and real hardware. While Linux e1000e driver always writes VET register to 0x8100, it is not always the case for everyone. Drivers relying on the reset value of VET won't be able to transmit and receive VLAN frames in QEMU. Unlike e1000 in QEMU, e1000e uses a field 'vet' in "struct E1000Core" to cache the value of VET register, but the cache only gets updated when VET register is written. To always get a consistent VET value no matter VET is written or remains its reset value, drop the 'vet' field and use 'core->mac[VET]' directly. Reported-by: Markus Carlstedt <markus.carlstedt@windriver.com> Signed-off-by: Christina Wang <christina.wang@windriver.com> Signed-off-by: Bin Meng <bin.meng@windriver.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2021-03-09sysemu: Let VMChangeStateHandler take boolean 'running' argumentPhilippe Mathieu-Daudé
The 'running' argument from VMChangeStateHandler does not require other value than 0 / 1. Make it a plain boolean. Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com> Reviewed-by: Alex Bennée <alex.bennee@linaro.org> Acked-by: David Gibson <david@gibson.dropbear.id.au> Message-Id: <20210111152020.1422021-3-philmd@redhat.com> Signed-off-by: Laurent Vivier <laurent@vivier.eu>
2021-01-08Remove superfluous timer_del() callsPeter Maydell
This commit is the result of running the timer-del-timer-free.cocci script on the whole source tree. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Acked-by: Corey Minyard <cminyard@mvista.com> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20201215154107.3255-4-peter.maydell@linaro.org
2020-11-24hw/net/e1000e: advance desc_offset in case of null descriptorPrasad J Pandit
While receiving packets via e1000e_write_packet_to_guest() routine, 'desc_offset' is advanced only when RX descriptor is processed. And RX descriptor is not processed if it has NULL buffer address. This may lead to an infinite loop condition. Increament 'desc_offset' to process next descriptor in the ring to avoid infinite loop. Reported-by: Cheol-woo Myung <330cjfdn@gmail.com> Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org> Signed-off-by: Jason Wang <jasowang@redhat.com>
2020-11-15e1000e: Fix Lesser GPL version numberChetan Pant
There is no "version 2" of the "Lesser" General Public License. It is either "GPL version 2.0" or "Lesser GPL version 2.1". This patch replaces all occurrences of "Lesser GPL version 2" with "Lesser GPL version 2.1" in comment section. Signed-off-by: Chetan Pant <chetan4windows@gmail.com> Message-Id: <20201023124134.20083-1-chetan4windows@gmail.com> Reviewed-by: Thomas Huth <thuth@redhat.com> Signed-off-by: Thomas Huth <thuth@redhat.com>
2020-09-10hw/net/e1000e: Remove duplicated write handler for FLSWDATA registerPhilippe Mathieu-Daudé
The FLSWDATA register writeop handler is initialized twice: 3067 #define e1000e_putreg(x) [x] = e1000e_mac_writereg 3068 typedef void (*writeops)(E1000ECore *, int, uint32_t); 3069 static const writeops e1000e_macreg_writeops[] = { .... 3102 e1000e_putreg(FLSWDATA), .... 3145 e1000e_putreg(FLSWDATA), To avoid confusion, remove the duplicated initialization. Fixes: 6f3fbe4ed0 ("net: Introduce e1000e device emulation") Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Li Qiang <liq3ea@gmail.com> Message-Id: <20200904131402.590055-3-f4bug@amsat.org> Signed-off-by: Laurent Vivier <laurent@vivier.eu>
2020-09-10hw/net/e1000e: Remove overwritten read handler for STATUS registerPhilippe Mathieu-Daudé
The STATUS register readop handler is initialized first with the generic e1000e_mac_readreg() handler: 2861 #define e1000e_getreg(x) [x] = e1000e_mac_readreg 2862 typedef uint32_t (*readops)(E1000ECore *, int); 2863 static const readops e1000e_macreg_readops[] = { .... 2919 e1000e_getreg(STATUS), Then overwritten with the specific e1000e_get_status handler: 3018 [STATUS] = e1000e_get_status, To avoid confusion, remove the overwritten initialization. 6f3fbe4ed0 ("net: Introduce e1000e device emulation") Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Li Qiang <liq3ea@gmail.com> Message-Id: <20200904131402.590055-2-f4bug@amsat.org> Signed-off-by: Laurent Vivier <laurent@vivier.eu>
2020-06-18hw/net/e1000e: Do not abort() on invalid PSRCTL register valuePhilippe Mathieu-Daudé
libFuzzer found using 'qemu-system-i386 -M q35': qemu: hardware error: e1000e: PSRCTL.BSIZE0 cannot be zero CPU #0: EAX=00000000 EBX=00000000 ECX=00000000 EDX=00000663 ESI=00000000 EDI=00000000 EBP=00000000 ESP=00000000 EIP=0000fff0 EFL=00000002 [-------] CPL=0 II=0 A20=1 SMM=0 HLT=0 ES =0000 00000000 0000ffff 00009300 CS =f000 ffff0000 0000ffff 00009b00 SS =0000 00000000 0000ffff 00009300 DS =0000 00000000 0000ffff 00009300 FS =0000 00000000 0000ffff 00009300 GS =0000 00000000 0000ffff 00009300 LDT=0000 00000000 0000ffff 00008200 TR =0000 00000000 0000ffff 00008b00 GDT= 00000000 0000ffff IDT= 00000000 0000ffff CR0=60000010 CR2=00000000 CR3=00000000 CR4=00000000 DR0=00000000 DR1=00000000 DR2=00000000 DR3=00000000 DR6=ffff0ff0 DR7=00000400 EFER=0000000000000000 FCW=037f FSW=0000 [ST=0] FTW=00 MXCSR=00001f80 FPR0=0000000000000000 0000 FPR1=0000000000000000 0000 FPR2=0000000000000000 0000 FPR3=0000000000000000 0000 FPR4=0000000000000000 0000 FPR5=0000000000000000 0000 FPR6=0000000000000000 0000 FPR7=0000000000000000 0000 XMM00=00000000000000000000000000000000 XMM01=00000000000000000000000000000000 XMM02=00000000000000000000000000000000 XMM03=00000000000000000000000000000000 XMM04=00000000000000000000000000000000 XMM05=00000000000000000000000000000000 XMM06=00000000000000000000000000000000 XMM07=00000000000000000000000000000000 ==1988== ERROR: libFuzzer: deadly signal #6 0x7fae4d3ea894 in __GI_abort (/lib64/libc.so.6+0x22894) #7 0x563f4cc59a1d in hw_error (qemu-fuzz-i386+0xe8ca1d) #8 0x563f4d7c93f2 in e1000e_set_psrctl (qemu-fuzz-i386+0x19fc3f2) #9 0x563f4d7b798f in e1000e_core_write (qemu-fuzz-i386+0x19ea98f) #10 0x563f4d7afc46 in e1000e_mmio_write (qemu-fuzz-i386+0x19e2c46) #11 0x563f4cc9a0a7 in memory_region_write_accessor (qemu-fuzz-i386+0xecd0a7) #12 0x563f4cc99c13 in access_with_adjusted_size (qemu-fuzz-i386+0xeccc13) #13 0x563f4cc987b4 in memory_region_dispatch_write (qemu-fuzz-i386+0xecb7b4) It simply sent the following 2 I/O command to the e1000e PCI BAR #2 I/O region: writew 0x0100 0x0c00 # RCTL = E1000_RCTL_DTYP_MASK writeb 0x2170 0x00 # PSRCTL = 0 2813 static void 2814 e1000e_set_psrctl(E1000ECore *core, int index, uint32_t val) 2815 { 2816 if (core->mac[RCTL] & E1000_RCTL_DTYP_MASK) { 2817 2818 if ((val & E1000_PSRCTL_BSIZE0_MASK) == 0) { 2819 hw_error("e1000e: PSRCTL.BSIZE0 cannot be zero"); 2820 } Instead of calling hw_error() which abort the process (it is meant for CPU fatal error condition, not for device logging), log the invalid request with qemu_log_mask(LOG_GUEST_ERROR) and return, ignoring the request. Cc: qemu-stable@nongnu.org Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Signed-off-by: Jason Wang <jasowang@redhat.com>
2020-03-31hw/net/e1000e_core: Let e1000e_can_receive() return a booleanPhilippe Mathieu-Daudé
The e1000e_can_receive() function simply returns a boolean value. Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com>
2020-03-09hw/net/e1000: Move macreg[] arrays to .rodata to save 1MiB of .dataPhilippe Mathieu-Daudé
Each array consumes 256KiB of .data. As we do not reassign entries, we can move it to the .rodata section, and save a total of 1MiB of .data (size reported on x86_64 host). Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Dmitry Fleytman <dmitry.fleytman@gmail.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Message-Id: <20200305010446.17029-3-philmd@redhat.com> Signed-off-by: Laurent Vivier <laurent@vivier.eu>
generated by cgit v1.2.3 (git 2.26.2) at 2025-03-23 04:39:33 +0000