aboutsummaryrefslogtreecommitdiff
path: root/hw/misc/trace-events
AgeCommit message (Collapse)Author
2023-01-12hw/misc: AXP209 PMU EmulationStrahinja Jankovic
This patch adds minimal support for AXP-209 PMU. Most important is chip ID since U-Boot SPL expects version 0x1. Besides the chip ID register, reset values for two more registers used by A10 U-Boot SPL are covered. Signed-off-by: Strahinja Jankovic <strahinja.p.jankovic@gmail.com> Message-id: 20221226220303.14420-5-strahinja.p.jankovic@gmail.com Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2022-08-08hw/misc/grlib_ahb_apb_pnp: Support 8 and 16 bit accessesPeter Maydell
In real hardware, the APB and AHB PNP data tables can be accessed with byte and halfword reads as well as word reads. Our implementation currently only handles word reads. Add support for the 8 and 16 bit accesses. Note that we only need to handle aligned accesses -- unaligned accesses should continue to trap, as happens on hardware. Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1132 Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Frederic Konrad <fkonrad@amd.com> Message-Id: <20220802131925.3380923-1-peter.maydell@linaro.org> Tested-by: Tomasz Martyniak <gitlab.com/tom4r> Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
2022-06-30hw/misc/aspeed: Add PECI controllerPeter Delevoryas
This introduces a really basic PECI controller that responses to commands by always setting the response code to success and then raising an interrupt to indicate the command is done. This helps avoid getting hit with constant errors if the driver continuously attempts to send a command and keeps timing out. The AST2400 and AST2500 only included registers up to 0x5C, not 0xFC. They supported PECI 1.1, 2.0, and 3.0. The AST2600 and AST1030 support PECI 4.0, which includes more read/write buffer registers from 0x80 to 0xFC to support 64-byte mode. This patch doesn't attempt to handle that, or to create a different version of the controller for the different generations, since it's only implementing functionality that is common to all generations. The basic sequence of events is that the firmware will read and write to various registers and then trigger a command by setting the FIRE bit in the command register (similar to the I2C controller). Then the firmware waits for an interrupt from the PECI controller, expecting the interrupt status register to be filled in with info on what happened. If the command was transmitted and received successfully, then response codes from the host CPU will be found in the data buffer registers. Signed-off-by: Peter Delevoryas <pdel@fb.com> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220630045133.32251-12-me@pjd.dev> [ clg: s/sysbus_mmio_map/aspeed_mmio_map/ ] Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-30aspeed/scu: Add trace events for read opsCédric Le Goater
Reviewed-by: Peter Delevoryas <pdel@fb.com> Message-Id: <20220628154740.1117349-2-clg@kaod.org> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-05-08lasi: move from hw/hppa to hw/miscMark Cave-Ayland
Move the LASI device implementation from hw/hppa to hw/misc so that it is located with all the other miscellaneous devices. Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk> Acked-by: Helge Deller <deller@gmx.de> Message-Id: <20220504092600.10048-43-mark.cave-ayland@ilande.co.uk> Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
2022-03-24hw: Fix misleading hexadecimal formatPhilippe Mathieu-Daudé
"0x%u" format is very misleading, replace by "0x%x". Found running: $ git grep -E '0x%[0-9]*([lL]*|" ?PRI)[dDuU]' hw/ Inspired-by: Richard Henderson <richard.henderson@linaro.org> Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Daniel P. Berrangé <berrange@redhat.com> Message-id: 20220323114718.58714-3-philippe.mathieu.daude@gmail.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2022-03-09mos6522: add register names to register read/write trace eventsMark Cave-Ayland
This helps to follow how the guest is programming the mos6522 when debugging. Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Laurent Vivier <laurent@vivier.eu> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Message-Id: <20220305150957.5053-8-mark.cave-ayland@ilande.co.uk> Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
2022-02-26aspeed/sdmc: Add trace eventsCédric Le Goater
This is useful to analyze changes in the U-Boot RAM driver when SDRAM training is performed. Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-01-20hw/misc/aspeed_i3c.c: Introduce a dummy AST2600 I3C model.Troy Lee
Aspeed 2600 SDK enables I3C support by default. The I3C driver will try to reset the device controller and set it up through device address table register. This dummy model responds to these registers with default values as listed in the ast2600v10 datasheet chapter 54.2. This avoids a guest machine kernel panic due to referencing an invalid kernel address if the device address table register isn't set correctly. Signed-off-by: Troy Lee <troy_lee@aspeedtech.com> Reviewed-by: Graeme Gregory <quic_ggregory@quicinc.com> Reviewed-by: Cédric Le Goater <clg@kaod.org> Tested-by: Graeme Gregory <quic_ggregory@quicinc.com> Message-id: 20220111084546.4145785-2-troy_lee@aspeedtech.com [PMM: tidied commit message; fixed format strings] Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2021-10-20mac_via: add GPIO for A/UX modeMark Cave-Ayland
Add a new auxmode GPIO that is updated when port B bit 6 is changed indicating whether the hardware is configured for A/UX mode. Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk> Reviewed-by: Laurent Vivier <laurent@vivier.eu> Message-Id: <20211020134131.4392-5-mark.cave-ayland@ilande.co.uk> Signed-off-by: Laurent Vivier <laurent@vivier.eu>
2021-06-02docs: fix references to docs/devel/tracing.rstStefano Garzarella
Commit e50caf4a5c ("tracing: convert documentation to rST") converted docs/devel/tracing.txt to docs/devel/tracing.rst. We still have several references to the old file, so let's fix them with the following command: sed -i s/tracing.txt/tracing.rst/ $(git grep -l docs/devel/tracing.txt) Signed-off-by: Stefano Garzarella <sgarzare@redhat.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com> Message-Id: <20210517151702.109066-2-sgarzare@redhat.com> Signed-off-by: Thomas Huth <thuth@redhat.com>
2021-05-12Drop the deprecated lm32 targetMarkus Armbruster
Target lm32 was deprecated in commit d8498005122, v5.2.0. See there for rationale. Some of its code lives on in device models derived from milkymist ones: hw/char/digic-uart.c and hw/display/bcm2835_fb.c. Cc: Michael Walle <michael@walle.cc> Signed-off-by: Markus Armbruster <armbru@redhat.com> Message-Id: <20210503084034.3804963-2-armbru@redhat.com> Acked-by: Michael Walle <michael@walle.cc> [Trivial conflicts resolved, reST markup fixed]
2021-03-18Merge remote-tracking branch 'remotes/vivier/tags/q800-for-6.0-pull-request' ↵Peter Maydell
into staging q800 pull request 20210316 Several fixes for mac_via needed for future support of MacOS ROM # gpg: Signature made Tue 16 Mar 2021 21:14:42 GMT # gpg: using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C # gpg: issuer "laurent@vivier.eu" # gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full] # gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full] # gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full] # Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C * remotes/vivier/tags/q800-for-6.0-pull-request: mac_via: remove VIA1 timer optimisations mac_via: fix 60Hz VIA1 timer interval mac_via: rename VBL timer to 60Hz timer mac_via: don't re-inject ADB response when switching to IDLE state mac_via: allow long accesses to VIA registers mac_via: fix up adb_via_receive() trace events mac_via: switch rtc pram trace-events to use hex rather than decimal for addresses Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2021-03-16mac_via: switch rtc pram trace-events to use hex rather than decimal for ↵Mark Cave-Ayland
addresses Since all the documentation uses the hex offsets, this makes it much easier to see what is going on. Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk> Reviewed-by: Laurent Vivier <laurent@vivier.eu> Message-Id: <20210311100505.22596-2-mark.cave-ayland@ilande.co.uk> Signed-off-by: Laurent Vivier <laurent@vivier.eu>
2021-03-15m68k: add a system controllerLaurent Vivier
Add a system controller for the m68k-virt machine. This controller allows the kernel to power off or reset the machine. Signed-off-by: Laurent Vivier <laurent@vivier.eu> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Message-Id: <20210312214145.2936082-5-laurent@vivier.eu>
2021-03-12hw/misc: Add NPCM7XX MFT ModuleHao Wu
This patch implements Multi Function Timer (MFT) module for NPCM7XX. This module is mainly used to configure PWM fans. It has just enough functionality to make the PWM fan kernel module work. The module takes two input, the max_rpm of a fan (modifiable via QMP) and duty cycle (a GPIO from the PWM module.) The actual measured RPM is equal to max_rpm * duty_cycle / NPCM7XX_PWM_MAX_DUTY. The RPM is measured as a counter compared to a prescaled input clock. The kernel driver reads this counter and report to user space. Refs: https://github.com/torvalds/linux/blob/master/drivers/hwmon/npcm750-pwm-fan.c Reviewed-by: Doug Evans <dje@google.com> Reviewed-by: Tyrone Ting <kfting@nuvoton.com> Signed-off-by: Hao Wu <wuhaotsh@google.com> Message-id: 20210311180855.149764-3-wuhaotsh@google.com Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2021-03-11Merge remote-tracking branch ↵Peter Maydell
'remotes/vivier2/tags/trivial-branch-for-6.0-pull-request' into staging Pull request # gpg: Signature made Wed 10 Mar 2021 21:56:09 GMT # gpg: using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C # gpg: issuer "laurent@vivier.eu" # gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full] # gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full] # gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full] # Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C * remotes/vivier2/tags/trivial-branch-for-6.0-pull-request: (22 commits) sysemu: Let VMChangeStateHandler take boolean 'running' argument sysemu/runstate: Let runstate_is_running() return bool hw/lm32/Kconfig: Have MILKYMIST select LM32_DEVICES hw/lm32/Kconfig: Rename CONFIG_LM32 -> CONFIG_LM32_DEVICES hw/lm32/Kconfig: Introduce CONFIG_LM32_EVR for lm32-evr/uclinux boards qemu-common.h: Update copyright string to 2021 tests/fp/fp-test: Replace the word 'blacklist' qemu-options: Replace the word 'blacklist' seccomp: Replace the word 'blacklist' scripts/tracetool: Replace the word 'whitelist' ui: Replace the word 'whitelist' virtio-gpu: Adjust code space style exec/memory: Use struct Object typedef fuzz-test: remove unneccessary debugging flags net: Use id_generate() in the network subsystem, too MAINTAINERS: Fix the location of tools manuals vhost_user_gpu: Drop dead check for g_malloc() failure backends/dbus-vmstate: Fix short read error handling target/hexagon/gen_tcg_funcs: Fix a typo hw/elf_ops: Fix a typo ... Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2021-03-09Various spelling fixesMichael Tokarev
An assorted set of spelling fixes in various places. Signed-off-by: Michael Tokarev <mjt@tls.msk.ru> Reviewed-by: Stefan Weil <sw@weilnetz.de> Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Message-Id: <20210309111510.79495-1-mjt@msgid.tls.msk.ru> Signed-off-by: Laurent Vivier <laurent@vivier.eu>
2021-03-08hw/misc/sse-cpu-pwrctrl: Implement SSE-300 CPU<N>_PWRCTRL register blockPeter Maydell
The SSE-300 has a new register block CPU<N>_PWRCTRL. There is one instance of this per CPU in the system (so just one for the SSE-300), and as well as the usual CIDR/PIDR ID registers it has just one register, CPUPWRCFG. This register allows the guest to configure behaviour of the system in power-down and deep-sleep states. Since QEMU does not model those, we make the register a dummy reads-as-written implementation. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20210219144617.4782-21-peter.maydell@linaro.org
2021-01-12hw/misc: Add a PWM module for NPCM7XXHao Wu
The PWM module is part of NPCM7XX module. Each NPCM7XX module has two identical PWM modules. Each module contains 4 PWM entries. Each PWM has two outputs: frequency and duty_cycle. Both are computed using inputs from software side. This module does not model detail pulse signals since it is expensive. It also does not model interrupts and watchdogs that are dependant on the detail models. The interfaces for these are left in the module so that anyone in need for these functionalities can implement on their own. The user can read the duty cycle and frequency using qom-get command. Reviewed-by: Havard Skinnemoen <hskinnemoen@google.com> Reviewed-by: Tyrone Ting <kfting@nuvoton.com> Signed-off-by: Hao Wu <wuhaotsh@google.com> Message-id: 20210108190945.949196-5-wuhaotsh@google.com Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2020-10-29Merge remote-tracking branch ↵Peter Maydell
'remotes/pmaydell/tags/pull-target-arm-20201027-1' into staging target-arm queue: * raspi: add model of cprman clock manager * sbsa-ref: add an SBSA generic watchdog device * arm/trace: Fix hex printing * raspi: Add models of Pi 3 model A+, Pi Zero and Pi A+ * hw/arm/smmuv3: Set the restoration priority of the vSMMUv3 explicitly * Nuvoton NPCM7xx: Add USB, RNG, GPIO and watchdog support * hw/arm: fix min_cpus for xlnx-versal-virt platform * hw/arm/highbank: Silence warnings about missing fallthrough statements * linux-user: Support Aarch64 BTI * Armv7M systick: fix corner case bugs by rewriting to use ptimer # gpg: Signature made Tue 27 Oct 2020 11:27:10 GMT # gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE # gpg: issuer "peter.maydell@linaro.org" # gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate] # gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate] # gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate] # Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE * remotes/pmaydell/tags/pull-target-arm-20201027-1: (48 commits) hw/timer/armv7m_systick: Rewrite to use ptimers hw/core/ptimer: Support ptimer being disabled by timer callback hw/arm/sbsa-ref: add SBSA watchdog device hw/watchdog: Implement SBSA watchdog device hw/arm/bcm2835_peripherals: connect the UART clock hw/char/pl011: add a clock input hw/misc/bcm2835_cprman: add sane reset values to the registers hw/misc/bcm2835_cprman: add the DSI0HSCK multiplexer hw/misc/bcm2835_cprman: implement clock mux behaviour hw/misc/bcm2835_cprman: add a clock mux skeleton implementation hw/misc/bcm2835_cprman: implement PLL channels behaviour hw/misc/bcm2835_cprman: add a PLL channel skeleton implementation hw/misc/bcm2835_cprman: implement PLLs behaviour hw/misc/bcm2835_cprman: add a PLL skeleton implementation hw/arm/raspi: add a skeleton implementation of the CPRMAN hw/arm/raspi: fix CPRMAN base address hw/core/clock: trace clock values in Hz instead of ns hw/core/clock: provide the VMSTATE_ARRAY_CLOCK macro arm/trace: Fix hex printing hw/arm/raspi: Add the Raspberry Pi 3 model A+ ... Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2020-10-27hw/arm/raspi: add a skeleton implementation of the CPRMANLuc Michel
The BCM2835 CPRMAN is the clock manager of the SoC. It is composed of a main oscillator, and several sub-components (PLLs, multiplexers, ...) to generate the BCM2835 clock tree. This commit adds a skeleton of the CPRMAN, with a dummy register read/write implementation. It embeds the main oscillator (xosc) from which all the clocks will be derived. Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Signed-off-by: Luc Michel <luc@lmichel.fr> Tested-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2020-10-27hw/misc: Add npcm7xx random number generatorHavard Skinnemoen
The RNG module returns a byte of randomness when the Data Valid bit is set. This implementation ignores the prescaler setting, and loads a new value into RNGD every time RNGCS is read while the RNG is enabled and random data is available. A qtest featuring some simple randomness tests is included. Reviewed-by: Tyrone Ting <kfting@nuvoton.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2020-10-26hw/misc/mps2-scc: Use the LED devicePhilippe Mathieu-Daudé
Per the 'ARM MPS2 and MPS2+ FPGA Prototyping Boards Technical Reference Manual' (100112_0200_07_en): 2.1 Overview of the MPS2 and MPS2+ hardware The MPS2 and MPS2+ FPGA Prototyping Boards contain the following components and interfaces: * User switches and user LEDs: - Two green LEDs and two push buttons that connect to the FPGA. - Eight green LEDs and one 8-way dip switch that connect to the MCC. Add the 8 LEDs connected to the MCC. This replaces the 'mps2_scc_leds' trace events by the generic 'led_set_intensity' event. Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Reviewed-by: Luc Michel <luc.michel@greensocs.com> Message-Id: <20200912134041.946260-7-f4bug@amsat.org>
2020-10-26hw/misc/mps2-fpgaio: Use the LED devicePhilippe Mathieu-Daudé
Per the 'ARM MPS2 and MPS2+ FPGA Prototyping Boards Technical Reference Manual' (100112_0200_07_en): 2.1 Overview of the MPS2 and MPS2+ hardware The MPS2 and MPS2+ FPGA Prototyping Boards contain the following components and interfaces: * User switches and user LEDs: - Two green LEDs and two push buttons that connect to the FPGA. - Eight green LEDs and one 8-way dip switch that connect to the MCC. Add the 2 LEDs connected to the FPGA. This replaces the 'mps2_fpgaio_leds' trace events by the generic 'led_set_intensity' event. Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Luc Michel <luc.michel@greensocs.com> Message-Id: <20200912134041.946260-6-f4bug@amsat.org>
2020-10-26hw/misc/led: Emit a trace event when LED intensity has changedPhilippe Mathieu-Daudé
Track the LED intensity, and emit a trace event when it changes. Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Reviewed-by: Luc Michel <luc.michel@greensocs.com> Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Message-Id: <20200912134041.946260-4-f4bug@amsat.org>
2020-10-26hw/misc/led: Add a LED devicePhilippe Mathieu-Daudé
Add a LED device which can be connected to a GPIO output. They can also be dimmed with PWM devices. For now we do not implement the dimmed mode, but in preparation of a future implementation, we start using the LED intensity. LEDs are limited to a fixed set of colors. Reviewed-by: Luc Michel <luc.michel@greensocs.com> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Message-Id: <20200912134041.946260-2-f4bug@amsat.org>
2020-09-14hw/misc: Add NPCM7xx Clock Controller device modelHavard Skinnemoen
Enough functionality to boot the Linux kernel has been implemented. This includes: - Correct power-on reset values so the various clock rates can be accurately calculated. - Clock enables stick around when written. In addition, a best effort attempt to implement SECCNT and CNTR25M was made even though I don't think the kernel needs them. Reviewed-by: Tyrone Ting <kfting@nuvoton.com> Reviewed-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Tested-by: Alexander Bulekov <alxndr@bu.edu> Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com> Message-id: 20200911052101.2602693-3-hskinnemoen@google.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2020-09-14hw/misc: Add NPCM7xx System Global Control Registers device modelHavard Skinnemoen
Implement a device model for the System Global Control Registers in the NPCM730 and NPCM750 BMC SoCs. This is primarily used to enable SMP boot (the boot ROM spins reading the SCRPAD register) and DDR memory initialization; other registers are best effort for now. The reset values of the MDLR and PWRON registers are determined by the SoC variant (730 vs 750) and board straps respectively. Reviewed-by: Joel Stanley <joel@jms.id.au> Reviewed-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Tested-by: Alexander Bulekov <alxndr@bu.edu> Signed-off-by: Havard Skinnemoen <hskinnemoen@google.com> Message-id: 20200911052101.2602693-2-hskinnemoen@google.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2020-09-09trace-events: Fix attribution of trace points to sourceMarkus Armbruster
Some trace points are attributed to the wrong source file. Happens when we neglect to update trace-events for code motion, or add events in the wrong place, or misspell the file name. Clean up with help of scripts/cleanup-trace-events.pl. Funnies requiring manual post-processing: * accel/tcg/cputlb.c trace points are in trace-events. * block.c and blockdev.c trace points are in block/trace-events. * hw/block/nvme.c uses the preprocessor to hide its trace point use from cleanup-trace-events.pl. * hw/tpm/tpm_spapr.c uses pseudo trace point tpm_spapr_show_buffer to guard debug code. * include/hw/xen/xen_common.h trace points are in hw/xen/trace-events. * linux-user/trace-events abbreviates a tedious list of filenames to */signal.c. * net/colo-compare and net/filter-rewriter.c use pseudo trace points colo_compare_miscompare and colo_filter_rewriter_debug to guard debug code. Signed-off-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com> Message-id: 20200806141334.3646302-5-armbru@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2020-09-09trace-events: Delete unused trace pointsMarkus Armbruster
Tracked down with the help of scripts/cleanup-trace-events.pl. Signed-off-by: Markus Armbruster <armbru@redhat.com> Message-id: 20200806141334.3646302-4-armbru@redhat.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2020-07-11hw/misc: avr: Add limited support for power reduction deviceMichael Rolnik
This is a simple device of just one register, and whenever this register is written to it calls qemu_set_irq function for each of 8 bits/IRQs. It is used to implement AVR Power Reduction. [AM: Remove word 'Atmel' from filenames and all elements of code] Suggested-by: Aleksandar Markovic <aleksandar.m.mail@gmail.com> Signed-off-by: Michael Rolnik <mrolnik@gmail.com> Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> [rth: Squash include fix and file rename from f4bug] Signed-off-by: Richard Henderson <richard.henderson@linaro.org> Signed-off-by: Aleksandar Markovic <aleksandar.m.mail@gmail.com> Reviewed-by: Alex Bennée <alex.bennee@linaro.org> Signed-off-by: Thomas Huth <huth@tuxfamily.org> Message-Id: <20200705140315.260514-22-huth@tuxfamily.org>
2020-06-26hw/misc/pca9552: Trace GPIO change eventsPhilippe Mathieu-Daudé
Emit a trace event when a GPIO change its state. Example booting obmc-phosphor-image: $ qemu-system-arm -M witherspoon-bmc -trace pca955x_gpio_change 1592690552.687372:pca955x_gpio_change pca1 GPIO id:0 status: 0 -> 1 1592690552.690169:pca955x_gpio_change pca1 GPIO id:1 status: 0 -> 1 1592690552.691673:pca955x_gpio_change pca1 GPIO id:2 status: 0 -> 1 1592690552.696886:pca955x_gpio_change pca1 GPIO id:3 status: 0 -> 1 1592690552.698614:pca955x_gpio_change pca1 GPIO id:13 status: 0 -> 1 1592690552.699833:pca955x_gpio_change pca1 GPIO id:14 status: 0 -> 1 1592690552.700842:pca955x_gpio_change pca1 GPIO id:15 status: 0 -> 1 1592690683.841921:pca955x_gpio_change pca1 GPIO id:14 status: 1 -> 0 1592690683.861660:pca955x_gpio_change pca1 GPIO id:14 status: 0 -> 1 1592690684.371460:pca955x_gpio_change pca1 GPIO id:14 status: 1 -> 0 1592690684.882115:pca955x_gpio_change pca1 GPIO id:14 status: 0 -> 1 1592690685.391411:pca955x_gpio_change pca1 GPIO id:14 status: 1 -> 0 1592690685.901391:pca955x_gpio_change pca1 GPIO id:14 status: 0 -> 1 1592690686.411678:pca955x_gpio_change pca1 GPIO id:14 status: 1 -> 0 1592690686.921279:pca955x_gpio_change pca1 GPIO id:14 status: 0 -> 1 We notice the GPIO #14 (front-power LED) starts to blink. This LED is described in the witherspoon device-tree [*]: front-power { retain-state-shutdown; default-state = "keep"; gpios = <&pca0 14 GPIO_ACTIVE_LOW>; }; [*] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dts?id=b1f9be9392f0#n140 Reviewed-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Tested-by: Cédric Le Goater <clg@kaod.org> Message-id: 20200623072723.6324-9-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2020-06-26hw/misc/pca9552: Trace GPIO High/Low eventsPhilippe Mathieu-Daudé
Add a trivial representation of the PCA9552 GPIOs. Example booting obmc-phosphor-image: $ qemu-system-arm -M witherspoon-bmc -trace pca955x_gpio_status 1592689902.327837:pca955x_gpio_status pca-unspecified GPIOs 0-15 [*...............] 1592689902.329934:pca955x_gpio_status pca-unspecified GPIOs 0-15 [**..............] 1592689902.330717:pca955x_gpio_status pca-unspecified GPIOs 0-15 [***.............] 1592689902.331431:pca955x_gpio_status pca-unspecified GPIOs 0-15 [****............] 1592689902.332163:pca955x_gpio_status pca-unspecified GPIOs 0-15 [****.........*..] 1592689902.332888:pca955x_gpio_status pca-unspecified GPIOs 0-15 [****.........**.] 1592689902.333629:pca955x_gpio_status pca-unspecified GPIOs 0-15 [****.........***] 1592690032.793289:pca955x_gpio_status pca-unspecified GPIOs 0-15 [****.........*.*] 1592690033.303163:pca955x_gpio_status pca-unspecified GPIOs 0-15 [****.........***] 1592690033.812962:pca955x_gpio_status pca-unspecified GPIOs 0-15 [****.........*.*] 1592690034.323234:pca955x_gpio_status pca-unspecified GPIOs 0-15 [****.........***] 1592690034.832922:pca955x_gpio_status pca-unspecified GPIOs 0-15 [****.........*.*] We notice the GPIO #14 (front-power LED) starts to blink. This LED is described in the witherspoon device-tree [*]: front-power { retain-state-shutdown; default-state = "keep"; gpios = <&pca0 14 GPIO_ACTIVE_LOW>; }; [*] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/arch/arm/boot/dts/aspeed-bmc-opp-witherspoon.dts?id=b1f9be9392f0#n140 Suggested-by: Cédric Le Goater <clg@kaod.org> Reviewed-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Tested-by: Cédric Le Goater <clg@kaod.org> Message-id: 20200623072723.6324-7-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2020-06-26mac_via: rework ADB state machine to be compatible with both MacOS and LinuxMark Cave-Ayland
The existing ADB state machine is designed to work with Linux which has a different interpretation of the state machine detailed in "Guide to the Macintosh Family Hardware". In particular the current Linux implementation includes an extra change to IDLE state when switching the VIA between send and receive modes which does not occur in MacOS, and omitting this transition causes the current mac_via ADB state machine to fail. Rework the ADB state machine accordingly so that it can enumerate and autopoll the ADB under both Linux and MacOS, including the addition of the new adb_autopoll_block() and adb_autopoll_unblock() functions. Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk> Tested-by: Finn Thain <fthain@telegraphics.com.au> Acked-by: Laurent Vivier <laurent@vivier.eu> Message-Id: <20200623204936.24064-20-mark.cave-ayland@ilande.co.uk>
2020-06-09hw/misc/grlib_ahb_apb_pnp: Add trace events on read accessesPhilippe Mathieu-Daudé
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: KONRAD Frederic <frederic.konrad@adacore.com> Message-Id: <20200331105048.27989-5-f4bug@amsat.org>
2020-06-09hw/misc/empty_slot: Move the 'hw/misc' and cover in MAINTAINERSPhilippe Mathieu-Daudé
Add an entry for the 'empty_slot' device. Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Acked-by: Artyom Tarasenko <atar4qemu@gmail.com> Message-Id: <20200510152840.13558-7-f4bug@amsat.org>
2020-03-12hw/arm/allwinner-h3: add SDRAM controller deviceNiek Linnenbank
In the Allwinner H3 SoC the SDRAM controller is responsible for interfacing with the external Synchronous Dynamic Random Access Memory (SDRAM). Types of memory that the SDRAM controller supports are DDR2/DDR3 and capacities of up to 2GiB. This commit adds emulation support of the Allwinner H3 SDRAM controller. Signed-off-by: Niek Linnenbank <nieklinnenbank@gmail.com> Reviewed-by: Alex Bennée <alex.bennee@linaro.org> Message-id: 20200311221854.30370-12-nieklinnenbank@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2020-03-12hw/arm/allwinner: add Security Identifier deviceNiek Linnenbank
The Security Identifier device found in various Allwinner System on Chip designs gives applications a per-board unique identifier. This commit adds support for the Allwinner Security Identifier using a 128-bit UUID value as input. Signed-off-by: Niek Linnenbank <nieklinnenbank@gmail.com> Reviewed-by: Alex Bennée <alex.bennee@linaro.org> Message-id: 20200311221854.30370-8-nieklinnenbank@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2020-03-12hw/arm/allwinner: add CPU Configuration moduleNiek Linnenbank
Various Allwinner System on Chip designs contain multiple processors that can be configured and reset using the generic CPU Configuration module interface. This commit adds support for the Allwinner CPU configuration interface which emulates the following features: * CPU reset * CPU status Signed-off-by: Niek Linnenbank <nieklinnenbank@gmail.com> Reviewed-by: Alex Bennée <alex.bennee@linaro.org> Message-id: 20200311221854.30370-7-nieklinnenbank@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2020-01-17hw/misc: Add the STM32F4xx EXTI deviceAlistair Francis
Signed-off-by: Alistair Francis <alistair@alistair23.me> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Message-id: ef941d59fd8658589d34ed432e1d6dfdcf7fb1d0.1576658572.git.alistair@alistair23.me Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2020-01-17hw/misc: Add the STM32F4xx Sysconfig deviceAlistair Francis
Signed-off-by: Alistair Francis <alistair@alistair23.me> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Message-id: 49b01423a09cef2ca832ff73a84a996568f1a8fc.1576658572.git.alistair@alistair23.me Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2020-01-07q800: fix mac_via RTC PRAM commandsLaurent Vivier
The command byte is not decoded correctly. This patch reworks the RTC/PRAM interface and fixes the problem. It adds a comment before the function to explain how are encoded commands and some trace-events to ease debugging. Bug: https://bugs.launchpad.net/qemu/+bug/1856549 Fixes: 6dca62a000 ("hw/m68k: add VIA support") Signed-off-by: Laurent Vivier <laurent@vivier.eu> Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk> Message-Id: <20191219201439.84804-2-laurent@vivier.eu>
2019-10-15hw/misc/bcm2835_mbox: Add trace eventsPhilippe Mathieu-Daudé
Add trace events for read/write accesses and IRQ. Properties are structures used for the ARM particular MBOX. Since one call in bcm2835_property.c concerns the mbox block, name this trace event in the same bcm2835_mbox* namespace. Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Alex Bennée <alex.bennee@linaro.org> Message-id: 20190926173428.10713-8-f4bug@amsat.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-09-18trace: Remove trailing newline in eventsPhilippe Mathieu-Daudé
While the tracing framework does not forbid trailing newline in events format string, using them lead to confuse output. It is the responsibility of the backend to properly end an event line. Some of our formats have trailing newlines, remove them. [Fixed typo in commit description reported by Eric Blake <eblake@redhat.com> --Stefan] Reviewed-by: John Snow <jsnow@redhat.com> Reviewed-by: Kevin Wolf <kwolf@redhat.com> Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com> Message-id: 20190916095121.29506-2-philmd@redhat.com Message-Id: <20190916095121.29506-2-philmd@redhat.com> Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2019-07-01hw/misc/aspeed_xdma: New deviceEddie James
The XDMA engine embedded in the Aspeed SOCs performs PCI DMA operations between the SOC (acting as a BMC) and a host processor in a server. The XDMA engine exists on the AST2400, AST2500, and AST2600 SOCs, so enable it for all of those. Add trace events on the important register writes in the XDMA engine. Signed-off-by: Eddie James <eajames@linux.ibm.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com> Signed-off-by: Cédric Le Goater <clg@kaod.org> Message-id: 20190618165311.27066-21-clg@kaod.org [clg: - changed title ] Signed-off-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-03-22trace-events: Fix attribution of trace points to sourceMarkus Armbruster
Some trace points are attributed to the wrong source file. Happens when we neglect to update trace-events for code motion, or add events in the wrong place, or misspell the file name. Clean up with help of cleanup-trace-events.pl. Same funnies as in the previous commit, of course. Manually shorten its change to linux-user/trace-events to */signal.c. Signed-off-by: Markus Armbruster <armbru@redhat.com> Message-id: 20190314180929.27722-6-armbru@redhat.com Message-Id: <20190314180929.27722-6-armbru@redhat.com> Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2019-03-22trace-events: Delete unused trace pointsMarkus Armbruster
Tracked down with cleanup-trace-events.pl. Funnies requiring manual post-processing: * block.c and blockdev.c trace points are in block/trace-events. * hw/block/nvme.c uses the preprocessor to hide its trace point use from cleanup-trace-events.pl. * include/hw/xen/xen_common.h trace points are in hw/xen/trace-events. * net/colo-compare and net/filter-rewriter.c use pseudo trace points colo_compare_udp_miscompare and colo_filter_rewriter_debug to guard debug code. Signed-off-by: Markus Armbruster <armbru@redhat.com> Message-id: 20190314180929.27722-5-armbru@redhat.com Message-Id: <20190314180929.27722-5-armbru@redhat.com> Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2019-03-22trace-events: Shorten file names in commentsMarkus Armbruster
We spell out sub/dir/ in sub/dir/trace-events' comments pointing to source files. That's because when trace-events got split up, the comments were moved verbatim. Delete the sub/dir/ part from these comments. Gets rid of several misspellings. Signed-off-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com> Message-id: 20190314180929.27722-3-armbru@redhat.com Message-Id: <20190314180929.27722-3-armbru@redhat.com> Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2019-02-28hw/misc/armsse-mhu.c: Model the SSE-200 Message Handling UnitPeter Maydell
Implement a model of the Message Handling Unit (MHU) found in the Arm SSE-200. This is a simple device which just contains some registers which allow the two cores of the SSE-200 to raise interrupts on each other. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20190219125808.25174-2-peter.maydell@linaro.org
generated by cgit v1.2.3 (git 2.26.2) at 2024-11-24 08:52:26 +0000