| Age | Commit message (Collapse) | Author |
|---|
|
MIPS KVM trap & emulate guest kernels have a different segment layout
compared with traditional MIPS kernels, to allow both the user and
kernel code to run from the user address segment without repeatedly
trapping to KVM.
QEMU currently supports this layout only for KVM, but its sometimes
useful to be able to run these kernels in QEMU on a PC, so enable it for
TCG too.
This also paves the way for MIPS KVM VZ support (which uses the normal
virtual memory layout) by abstracting whether user mode kernel segments
are in use.
Suggested-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Yongbok Kim <yongbok.kim@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: kvm@vger.kernel.org
Reviewed-by: Richard Henderson <rth@twiddle.net>
[Yongbok Kim:
minor change]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
|
|
Since commit 9768e2abf7 the initrd is loaded at the end of the low
memory to avoid clash for the kernel relocation when kaslr is used.
However this in turn conflicts with the bootmap memory that the kernel
tries to place after initrd, but in low memory. The bootmap spans the
whole usable physical address space. The machine can have at most 2GiB
of memory, 256MiB of low memory mapped at 0x00000000, and 1792MiB of
high memory mapped at 0x90000000. The biggest bootmap therefore
corresponds to the adresses 0x00000000 -> 0xffffffff, which at 1 bit
per 4kiB page corresponds to 128kiB in memory.
Therefore reserve 128kiB after the initrd.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Tested-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
|
|
Emulated MIPS boards bail out with a simple "could not load kernel" when
a kernel could not be load, without specifying the underlying reason.
Fix that by calling load_elf_strerror.
At the same time use error_report to report the error instead of
fprintf.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
|
|
Instead of reaching into the PCI state, allow the AHCIDevice to
respond with how many ports it has.
Signed-off-by: John Snow <jsnow@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20170623220926.11479-2-jsnow@redhat.com
Signed-off-by: John Snow <jsnow@redhat.com>
|
|
Use the new functions memory_region_init_{ram,rom,rom_device}()
instead of manually calling the _nomigrate() version and then
vmstate_register_ram_global().
Patch automatically created using coccinelle script:
spatch --in-place -sp_file scripts/coccinelle/memory-region-init-ram.cocci -dir hw
(As it turns out, there are no instances of the rom and
rom_device functions that are caught by this script.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1499438577-7674-8-git-send-email-peter.maydell@linaro.org
|
|
Rename memory_region_init_rom() to memory_region_init_rom_nomigrate()
and memory_region_init_rom_device() to
memory_region_init_rom_device_nomigrate().
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1499438577-7674-5-git-send-email-peter.maydell@linaro.org
|
|
Rename memory_region_init_ram() to memory_region_init_ram_nomigrate().
This leaves the way clear for us to provide a memory_region_init_ram()
which does handle migration.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-id: 1499438577-7674-4-git-send-email-peter.maydell@linaro.org
|
|
This defines new QOM object - IOMMUMemoryRegion - with MemoryRegion
as a parent.
This moves IOMMU-related fields from MR to IOMMU MR. However to avoid
dymanic QOM casting in fast path (address_space_translate, etc),
this adds an @is_iommu boolean flag to MR and provides new helper to
do simple cast to IOMMU MR - memory_region_get_iommu. The flag
is set in the instance init callback. This defines
memory_region_is_iommu as memory_region_get_iommu()!=NULL.
This switches MemoryRegion to IOMMUMemoryRegion in most places except
the ones where MemoryRegion may be an alias.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Message-Id: <20170711035620.4232-2-aik@ozlabs.ru>
Acked-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Frontends should have an interface to setup the handler of a backend change.
The interface will be used in the next commits
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <1499342940-56739-3-git-send-email-anton.nefedov@virtuozzo.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Currently the malta board is loading the initrd just after the kernel.
This doesn't work for kaslr enabled kernels, as the initrd ends-up being
overwritten.
Move the initrd at the end of the low memory, that should leave a
sufficient gap for kaslr.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Tested-by: Yongbok Kim <yongbok.kim@imgtec.com>
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
|
|
So they are all in one place. The following patch will move serial &
parallel declarations to the respective headers.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
|
|
Those are apparently unnecessary includes.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
|
|
Time to wire up all the call sites that request a shutdown or
reset to use the enum added in the previous patch.
It would have been less churn to keep the common case with no
arguments as meaning guest-triggered, and only modified the
host-triggered code paths, via a wrapper function, but then we'd
still have to audit that I didn't miss any host-triggered spots;
changing the signature forces us to double-check that I correctly
categorized all callers.
Since command line options can change whether a guest reset request
causes an actual reset vs. a shutdown, it's easy to also add the
information to reset requests.
Signed-off-by: Eric Blake <eblake@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au> [ppc parts]
Reviewed-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk> [SPARC part]
Reviewed-by: Cornelia Huck <cornelia.huck@de.ibm.com> [s390x parts]
Message-Id: <20170515214114.15442-5-eblake@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
|
|
cannot_instantiate_with_device_add_yet was introduced by commit
efec3dd631d94160288392721a5f9c39e50fb2bc to replace no_user. It was
supposed to be a temporary measure.
When it was introduced, we had 54
cannot_instantiate_with_device_add_yet=true lines in the code.
Today (3 years later) this number has not shrunk: we now have
57 cannot_instantiate_with_device_add_yet=true lines. I think it
is safe to say it is not a temporary measure, and we won't see
the flag go away soon.
Instead of a long field name that misleads people to believe it
is temporary, replace it a shorter and less misleading field:
user_creatable.
Except for code comments, changes were generated using the
following Coccinelle patch:
@@
expression DC;
@@
(
-DC->cannot_instantiate_with_device_add_yet = false;
+DC->user_creatable = true;
|
-DC->cannot_instantiate_with_device_add_yet = true;
+DC->user_creatable = false;
)
@@
typedef ObjectClass;
expression dc;
identifier class, data;
@@
static void device_class_init(ObjectClass *class, void *data)
{
...
dc->hotpluggable = true;
+dc->user_creatable = true;
...
}
@@
@@
struct DeviceClass {
...
-bool cannot_instantiate_with_device_add_yet;
+bool user_creatable;
...
}
@@
expression DC;
@@
(
-!DC->cannot_instantiate_with_device_add_yet
+DC->user_creatable
|
-DC->cannot_instantiate_with_device_add_yet
+!DC->user_creatable
)
Cc: Alistair Francis <alistair.francis@xilinx.com>
Cc: Laszlo Ersek <lersek@redhat.com>
Cc: Marcel Apfelbaum <marcel@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Thomas Huth <thuth@redhat.com>
Acked-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Message-Id: <20170503203604.31462-2-ehabkost@redhat.com>
[ehabkost: kept "TODO remove once we're there" comment]
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
Introduce support for emulating the MIPS Boston development board. The
Boston board is built around an FPGA & 3 PCIe controllers, one of which
is connected to an Intel EG20T Platform Controller Hub. It is used
during the development & debug of new CPUs and the software intended to
run on them, and is essentially the successor to the older MIPS Malta
board.
This patch does not implement the EG20T, instead connecting an already
supported ICH-9 AHCI controller. Whilst this isn't accurate it's enough
for typical stock Boston software (eg. Linux kernels) to work with hard
disks given that both the ICH-9 & EG20T implement the AHCI
specification.
Boston boards typically boot kernels in the FIT image format, and this
patch will treat kernels provided to QEMU as such. When loading a kernel
directly, the board code will generate minimal firmware much as the
Malta board code does. This firmware will set up the CM, CPC & GIC
register base addresses then set argument registers & jump to the kernel
entry point. Alternatively, bootloader code may be loaded using the bios
argument in which case no firmware will be generated & execution will
proceed from the start of the boot code at the default MIPS boot
exception vector (offset 0x1fc00000 into (c)kseg1).
Currently real Boston boards are always used with FPGA bitfiles that
include a Global Interrupt Controller (GIC), so the interrupt
configuration is only defined for such cases. Therefore the board will
only allow use of CPUs which implement the CPS components, including the
GIC, and will otherwise exit with a message.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
[yongbok.kim@imgtec.com:
isolated boston machine support for mips64el.
updated for recent Chardev changes.
ignore missing bios/kernel for qtest.
added default -drive to if=ide explicitly.
changed default memory size into 1G due to make check failure
on 32-bit hosts]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
|
|
This reverts commit d3473e147a754e999718bf6fcb015d9978c6a1ee.
This commit creates a board which defaults to having 2GB of RAM.
Unfortunately on 32-bit hosts we can't create boards with 2GB of RAM,
and so 'make check' fails. I missed this during testing of the
merge, unfortunately. Luckily the offending commit is the last
one in the merge request, so we can just revert it for now.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Introduce support for emulating the MIPS Boston development board. The
Boston board is built around an FPGA & 3 PCIe controllers, one of which
is connected to an Intel EG20T Platform Controller Hub. It is used
during the development & debug of new CPUs and the software intended to
run on them, and is essentially the successor to the older MIPS Malta
board.
This patch does not implement the EG20T, instead connecting an already
supported ICH-9 AHCI controller. Whilst this isn't accurate it's enough
for typical stock Boston software (eg. Linux kernels) to work with hard
disks given that both the ICH-9 & EG20T implement the AHCI
specification.
Boston boards typically boot kernels in the FIT image format, and this
patch will treat kernels provided to QEMU as such. When loading a kernel
directly, the board code will generate minimal firmware much as the
Malta board code does. This firmware will set up the CM, CPC & GIC
register base addresses then set argument registers & jump to the kernel
entry point. Alternatively, bootloader code may be loaded using the bios
argument in which case no firmware will be generated & execution will
proceed from the start of the boot code at the default MIPS boot
exception vector (offset 0x1fc00000 into (c)kseg1).
Currently real Boston boards are always used with FPGA bitfiles that
include a Global Interrupt Controller (GIC), so the interrupt
configuration is only defined for such cases. Therefore the board will
only allow use of CPUs which implement the CPS components, including the
GIC, and will otherwise exit with a message.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
[yongbok.kim@imgtec.com:
isolated boston machine support for mips64el.
updated for recent Chardev changes.
ignore missing bios/kernel for qtest.
added default -drive to if=ide explicitly]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
|
|
We've traditionally rejected orphans here and there, but not
systematically. For instance, the sun4m machines have an onboard SCSI
HBA (bus=0), and have always rejected bus>0. Other machines with an
onboard SCSI HBA don't.
Commit a66c9dc made all orphans trigger a warning, and the previous
commit turned this into an error. The checks "here and there" are now
redundant. Drop them.
Note that the one in mips_jazz.c was wrong: it rejected bus > MAX_FD,
but MAX_FD is the number of floppy drives per bus.
Error messages change from
$ qemu-system-x86_64 -drive if=ide,bus=2
qemu-system-x86_64: Too many IDE buses defined (3 > 2)
$ qemu-system-mips64 -M magnum,accel=qtest -drive if=floppy,bus=2,id=fd1
qemu: too many floppy drives
$ qemu-system-sparc -M LX -drive if=scsi,bus=1
qemu: too many SCSI bus
to
$ qemu-system-x86_64 -drive if=ide,bus=2
qemu-system-x86_64: -drive if=ide,bus=2: machine type does not support if=ide,bus=2,unit=0
$ qemu-system-mips64 -M magnum,accel=qtest -drive if=floppy,bus=2,id=fd1
qemu-system-mips64: -drive if=floppy,bus=2,id=fd1: machine type does not support if=floppy,bus=2,unit=0
$ qemu-system-sparc -M LX -drive if=scsi,bus=1
qemu-system-sparc: -drive if=scsi,bus=1: machine type does not support if=scsi,bus=1,unit=0
Cc: John Snow <jsnow@redhat.com>
Cc: "Hervé Poussineau" <hpoussin@reactos.org>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1487153147-11530-9-git-send-email-armbru@redhat.com>
Reviewed-by: John Snow <jsnow@redhat.com>
|
|
Block backends defined with -drive if=ide are meant to be picked up by
machine initialization code: a suitable frontend gets created and
wired up automatically.
if=ide drives not picked up that way can still be used with -device as
if they had if=none, but that's unclean and best avoided. Unused ones
produce an "Orphaned drive without device" warning.
-drive parameter "if" is optional, and the default depends on the
machine type. If a machine type doesn't specify a default, the
default is "ide".
Many machine types default to if=ide, even though they don't actually
have an IDE controller. A future patch will change these defaults to
something more sensible. To prepare for it, this patch makes default
"ide" explicit for the machines that actually pick up if=ide drives:
* alpha: clipper
* arm/aarch64: spitz borzoi terrier tosa
* i386/x86_64: generic-pc-machine (with concrete subtypes pc-q35-*
pc-i440fx-* pc-* isapc xenfv)
* mips64el: fulong2e
* mips/mipsel/mips64el: malta mips
* ppc/ppc64: mac99 g3beige prep
* sh4/sh4eb: r2d
* sparc64: sun4u sun4v
Note that ppc64 machine powernv already sets an "ide" default
explicitly. Its IDE controller isn't implemented, yet.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1487153147-11530-2-git-send-email-armbru@redhat.com>
|
|
Pick a uniform chardev type name.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Some files contain multiple #includes of the same header file.
Removed most of those unnecessary duplicate entries using
scripts/clean-includes.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Anand J <anand.indukala@gmail.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
No need to keep explicit_fe_open around if it affects only a
qemu_chr_fe_set_handlers(). Use an additional argument instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-24-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This also switches from qemu_chr_add_handlers() to
qemu_chr_fe_set_handlers(). Note that qemu_chr_fe_set_handlers() now
takes the focus when fe_open (qemu_chr_add_handlers() did take the
focus)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-16-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Similar to previous change, for the remaining CharDriverState front ends
users.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-13-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The CharDriverState.init() callback is no longer set since commit
a61ae7f88ce and thus unused. The only user, the malta FGPA display has
been converted to use an event "opened" callback instead.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-7-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The CharDriverState.init() callback was introduced in commit
ceecf1d158. It is only called from text_console_do_init(), but it is no
longer set since commit a61ae7f88 (init assignment has been removed by
accident).
It seems correct to use an event callback instead and print the console
text on CHR_EVENT_OPENED. That way we can remove the single user of
CharDriverState init().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-6-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Since commit b6607a1a204d, serial_hds_isa_init() was introduced to
factor out serial_isa_init() loops. However, sun4uv shouldn't start from
0 when there is a mm serial on 0 already. Add a "from" argument to
serial_hds_isa_init().
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Message-Id: <20161022095318.17775-5-marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Commit 9af9e0f, 6daf194d, be62a2eb and 312fd5f got rid of a bunch, but
they keep coming back. checkpatch.pl tries to flag them since commit
5d596c2, but it's not very good at it. Offenders tracked down with
Coccinelle script scripts/coccinelle/err-bad-newline.cocci, an updated
version of the script from commit 312fd5f.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Message-Id: <1470224274-31522-2-git-send-email-armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
|
|
The print routine provided as part of the in-built bootloader had a bug
in that it attempted to use a jump instruction as part of a loop, but
the target has its upper bits zeroed leading to control flow
transferring to 0xb0000814 rather than the intended 0xbfc00814. Fix this
by using a branch instruction instead, which seems more fit for purpose.
A simple way to test this is to build a Linux kernel with EVA enabled &
attempt to boot it in QEMU. It will attempt to print a message
indicating the configuration mismatch but QEMU would previously
incorrectly jump & wind up printing a continuous stream of the letter E.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Leon Alrae <leon.alrae@imgtec.com>
Reviewed-by: Aurelien Jarno <aurelien@aurel32.net>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Delay the host-bridge 'realization' until the
PCI root bus is attached.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Tested-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Acked-by: Leon Alrae <leon.alrae@imgtec.com>
Tested-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Add GIC to CPS and expose its interrupt pins instead of CPU's.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
This changes a cpu.h dependency into a cpu-qom.h dependency.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Make ITU available in the system if CPU supports multithreading
and is part of CPS.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
If the user specifies smp > 1 and the CPU with CM GCR support, then
create Coherent Processing System (which takes care of instantiating CPUs)
rather than CPUs directly and connect i8259 and cbus to the pins exposed by
CPS. However, there is no GIC yet, thus CPS exposes CPU's IRQ pins so use
the same pin numbers as before.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Global smp_cpus is never zero (even if user provides -smp 0), thus clocks
and irqs are always initialized for each created CPU in the loop at the
beginning of mips_malta_init.
These two lines cause a leak of already allocated timer and irqs for the
first CPU - remove them.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Remove CPUMIPSState from the write_bootloader() argument list as it
is not used in the function.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Create Cluster Power Controller and add a link to the CPC MemoryRegion
in GCR. Guest can enable / map CPC to any physical address by writing to
the memory-mapped GCR_CPC_BASE register.
Set vp-start-reset property to 1 to allow only first VP to run from reset.
Others are brought up by the guest via CPC memory-mapped registers.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Implement generic MIPS Coherent Processing System (CPS) which in this
commit just creates VPs, but it will serve as a container also for
other components like Global Configuration Registers and Cluster Power
Controller.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Move declarations out of qemu-common.h for functions declared in
utils/ files: e.g. include/qemu/path.h for utils/path.c.
Move inline functions out of qemu-common.h and into new files (e.g.
include/qemu/bcd.h)
Signed-off-by: Veronia Bahaa <veroniabahaa@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Commit 57cb38b included qapi/error.h into qemu/osdep.h to get the
Error typedef. Since then, we've moved to include qemu/osdep.h
everywhere. Its file comment explains: "To avoid getting into
possible circular include dependencies, this file should not include
any other QEMU headers, with the exceptions of config-host.h,
compiler.h, os-posix.h and os-win32.h, all of which are doing a
similar job to this file and are under similar constraints."
qapi/error.h doesn't do a similar job, and it doesn't adhere to
similar constraints: it includes qapi-types.h. That's in excess of
100KiB of crap most .c files don't actually need.
Add the typedef to qemu/typedefs.h, and include that instead of
qapi/error.h. Include qapi/error.h in .c files that need it and don't
get it now. Include qapi-types.h in qom/object.h for uint16List.
Update scripts/clean-includes accordingly. Update it further to match
reality: replace config.h by config-target.h, add sysemu/os-posix.h,
sysemu/os-win32.h. Update the list of includes in the qemu/osdep.h
comment quoted above similarly.
This reduces the number of objects depending on qapi/error.h from "all
of them" to less than a third. Unfortunately, the number depending on
qapi-types.h shrinks only a little. More work is needed for that one.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
[Fix compilation without the spice devel packages. - Paolo]
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Change all machine_init() users that simply call type_register*()
to use type_init().
Cc: Evgeny Voevodin <e.voevodin@samsung.com>
Cc: Maksim Kozlov <m.kozlov@samsung.com>
Cc: Igor Mitsyanko <i.mitsyanko@gmail.com>
Cc: Dmitry Solodkiy <d.solodkiy@samsung.com>
Cc: Peter Maydell <peter.maydell@linaro.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Andrzej Zaborowski <balrogg@gmail.com>
Cc: Michael Walle <michael@walle.cc>
Cc: "Hervé Poussineau" <hpoussin@reactos.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Leon Alrae <leon.alrae@imgtec.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Blue Swirl <blauwirbel@gmail.com>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Acked-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
|
|
Some CPUs are of an opposite data-endianness to other components in the
system. Sometimes elfs have the data sections layed out with this CPU
data-endianness accounting for when loaded via the CPU, so byte swaps
(relative to other system components) will occur.
The leading example, is ARM's BE32 mode, which is is basically LE with
address manipulation on half-word and byte accesses to access the
hw/byte reversed address. This means that word data is invariant
across LE and BE32. This also means that instructions are still LE.
The expectation is that the elf will be loaded via the CPU in this
endianness scheme, which means the data in the elf is reversed at
compile time.
As QEMU loads via the system memory directly, rather than the CPU, we
need a mechanism to reverse elf data endianness to implement this
possibility.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Floppy uses the DMA controller in rc4030 chipset, and not the i8259 from the ISA bus.
It's better to disable DMA than to call the wrong DMA controller.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-13-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
|
|
i8257 DMA controller exists on one ISA bus, so let's specify it at initialization.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-3-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
|
|
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
We can have at most one ISA bus. If you try to create another one,
isa_bus_new() complains to stderr and returns null.
isa_bus_new() is called in two contexts, machine's init() and device's
realize() methods. Since complaining to stderr is not proper in the
latter context, convert isa_bus_new() to Error.
Machine's init():
* mips_jazz_init(), called from the init() methods of machines
"magnum" and "pica"
* mips_r4k_init(), the init() method of machine "mips"
* pc_init1() called from the init() methods of non-q35 PC machines
* typhoon_init(), called from clipper_init(), the init() method of
machine "clipper"
These callers always create the first ISA bus, hence isa_bus_new()
can't fail. Simply pass &error_abort.
Device's realize():
* i82378_realize(), of PCI device "i82378"
* ich9_lpc_realize(), of PCI device "ICH9-LPC"
* pci_ebus_realize(), of PCI device "ebus"
* piix3_realize(), of PCI device "pci-piix3", abstract parent of
"PIIX3" and "PIIX3-xen"
* piix4_realize(), of PCI device "PIIX4"
* vt82c686b_realize(), of PCI device "VT82C686B"
Propagate the error. Note that these devices are typically created
only by machine init() methods with qdev_init_nofail() or similar. If
we screwed up and created an ISA bus before that call, we now give up
right away. Before, we'd hobble on, and typically die in
isa_bus_irqs(). Similar if someone finds a way to hot-plug one of
these critters.
Cc: Richard Henderson <rth@twiddle.net>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: "Hervé Poussineau" <hpoussin@reactos.org>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: Markus Armbruster <armbru@pond.sub.org>
Reviewed-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Message-Id: <1450370121-5768-11-git-send-email-armbru@redhat.com>
|
|
Signed-off-by: Cao jin <caoj.fnst@cn.fujitsu.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
