aboutsummaryrefslogtreecommitdiff
path: root/hw/char/cadence_uart.c
AgeCommit message (Collapse)Author
2021-09-13hw/char: cadence_uart: Log a guest error when device is unclocked or in resetBin Meng
We've got SW that expects FSBL (Bootlooader) to setup clocks and resets. It's quite common that users run that SW on QEMU without FSBL (FSBL typically requires the Xilinx tools installed). That's fine, since users can stil use -device loader to enable clocks etc. To help folks understand what's going, a log (guest-error) message would be helpful here. In particular with the serial port since things will go very quiet if they get things wrong. Suggested-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Message-id: 20210901124521.30599-7-bmeng.cn@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2021-09-13hw/char: cadence_uart: Ignore access when unclocked or in reset for ↵Bin Meng
uart_{read, write}() Read or write to uart registers when unclocked or in reset should be ignored. Add the check there, and as a result of this, the check in uart_write_tx_fifo() is now unnecessary. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Message-id: 20210901124521.30599-6-bmeng.cn@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2021-09-13hw/char: cadence_uart: Convert to memop_with_attrs() opsBin Meng
This converts uart_read() and uart_write() to memop_with_attrs() ops. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Message-id: 20210901124521.30599-5-bmeng.cn@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2021-09-13hw/char: cadence_uart: Move clock/reset check to uart_can_receive()Bin Meng
Currently the clock/reset check is done in uart_receive(), but we can move the check to uart_can_receive() which is earlier. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Message-id: 20210901124521.30599-4-bmeng.cn@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2021-09-13hw/char: cadence_uart: Disable transmit when input clock is disabledBin Meng
At present when input clock is disabled, any character transmitted to tx fifo can still show on the serial line, which is wrong. Fixes: b636db306e06 ("hw/char/cadence_uart: add clock support") Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Message-id: 20210901124521.30599-3-bmeng.cn@gmail.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2021-08-05chardev: mark explicitly first argument as poisonedMarc-André Lureau
Since commit 9894dc0cdcc397ee5b26370bc53da6d360a363c2 "char: convert from GIOChannel to QIOChannel", the first argument to the watch callback can actually be a QIOChannel, which is not a GIOChannel (but a QEMU Object). Even though we never used that pointer, change the callback type to warn the users. Possibly a better fix later, we may want to store the callback and call it from intermediary functions. Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
2021-03-08clock: Add ClockEvent parameter to callbacksPeter Maydell
The Clock framework allows users to specify a callback which is called after the clock's period has been updated. Some users need to also have a callback which is called before the clock period is updated. As the first step in adding support for notifying Clock users on pre-update events, add an argument to the ClockCallback to specify what event is being notified, and add an argument to the various functions for registering a callback to specify which events are of interest to that callback. Note that the documentation update renders correct the previously incorrect claim in 'Adding a new clock' that callbacks "will be explained in a following section". Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Luc Michel <luc@lmichel.fr> Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20210219144617.4782-2-peter.maydell@linaro.org
2020-12-18qdev: Move softmmu properties to qdev-properties-system.hEduardo Habkost
Move the property types and property macros implemented in qdev-properties-system.c to a new qdev-properties-system.h header. Signed-off-by: Eduardo Habkost <ehabkost@redhat.com> Reviewed-by: Igor Mammedov <imammedo@redhat.com> Message-Id: <20201211220529.2290218-16-ehabkost@redhat.com> Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
2020-04-30hw/char/cadence_uart: add clock supportDamien Hedde
Switch the cadence uart to multi-phase reset and add the reference clock input. The input clock frequency is added to the migration structure. The reference clock controls the baudrate generation. If it disabled, any input characters and events are ignored. If this clock remains unconnected, the uart behaves as before (it default to a 50MHz ref clock). Signed-off-by: Damien Hedde <damien.hedde@greensocs.com> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Message-id: 20200406135251.157596-8-damien.hedde@greensocs.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2020-01-24qdev: set properties with device_class_set_props()Marc-André Lureau
The following patch will need to handle properties registration during class_init time. Let's use a device_class_set_props() setter. spatch --macro-file scripts/cocci-macro-file.h --sp-file ./scripts/coccinelle/qdev-set-props.cocci --keep-comments --in-place --dir . @@ typedef DeviceClass; DeviceClass *d; expression val; @@ - d->props = val + device_class_set_props(d, val) Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Message-Id: <20200110153039.1379601-20-marcandre.lureau@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2020-01-08chardev: Use QEMUChrEvent enum in IOEventHandler typedefPhilippe Mathieu-Daudé
The Chardev events are listed in the QEMUChrEvent enum. By using the enum in the IOEventHandler typedef we: - make the IOEventHandler type more explicit (this handler process out-of-band information, while the IOReadHandler is in-band), - help static code analyzers. This patch was produced with the following spatch script: @match@ expression backend, opaque, context, set_open; identifier fd_can_read, fd_read, fd_event, be_change; @@ qemu_chr_fe_set_handlers(backend, fd_can_read, fd_read, fd_event, be_change, opaque, context, set_open); @depends on match@ identifier opaque, event; identifier match.fd_event; @@ static -void fd_event(void *opaque, int event) +void fd_event(void *opaque, QEMUChrEvent event) { ... } Then the typedef was modified manually in include/chardev/char-fe.h. Signed-off-by: Philippe Mathieu-Daudé <philmd@redhat.com> Acked-by: Corey Minyard <cminyard@mvista.com> Acked-by: Cornelia Huck <cohuck@redhat.com> Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com> Message-Id: <20191218172009.8868-15-philmd@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2019-08-16Include migration/vmstate.h lessMarkus Armbruster
In my "build everything" tree, changing migration/vmstate.h triggers a recompile of some 2700 out of 6600 objects (not counting tests and objects that don't depend on qemu/osdep.h). hw/hw.h supposedly includes it for convenience. Several other headers include it just to get VMStateDescription. The previous commit made that unnecessary. Include migration/vmstate.h only where it's still needed. Touching it now recompiles only some 1600 objects. Signed-off-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Message-Id: <20190812052359.30071-16-armbru@redhat.com> Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com>
2019-08-16Include hw/irq.h a lot lessMarkus Armbruster
In my "build everything" tree, changing hw/irq.h triggers a recompile of some 5400 out of 6600 objects (not counting tests and objects that don't depend on qemu/osdep.h). hw/hw.h supposedly includes it for convenience. Several other headers include it just to get qemu_irq and.or qemu_irq_handler. Move the qemu_irq and qemu_irq_handler typedefs from hw/irq.h to qemu/typedefs.h, and then include hw/irq.h only where it's still needed. Touching it now recompiles only some 500 objects. Signed-off-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com> Tested-by: Philippe Mathieu-Daudé <philmd@redhat.com> Message-Id: <20190812052359.30071-13-armbru@redhat.com>
2019-06-12Include qemu/module.h where needed, drop it from qemu-common.hMarkus Armbruster
Signed-off-by: Markus Armbruster <armbru@redhat.com> Message-Id: <20190523143508.25387-4-armbru@redhat.com> [Rebased with conflicts resolved automatically, except for hw/usb/dev-hub.c hw/misc/exynos4210_rng.c hw/misc/bcm2835_rng.c hw/misc/aspeed_scu.c hw/display/virtio-vga.c hw/arm/stm32f205_soc.c; ui/cocoa.m fixed up]
2018-01-16maint: Fix macros with broken 'do/while(0); ' usageEric Blake
The point of writing a macro embedded in a 'do { ... } while (0)' loop (particularly if the macro has multiple statements or would otherwise end with an 'if' statement) is so that the macro can be used as a drop-in statement with the caller supplying the trailing ';'. Although our coding style frowns on brace-less 'if': if (cond) statement; else something else; that is the classic case where failure to use do/while(0) wrapping would cause the 'else' to pair with any embedded 'if' in the macro rather than the intended outer 'if'. But conversely, if the macro includes an embedded ';', then the same brace-less coding style would now have two statements, making the 'else' a syntax error rather than pairing with the outer 'if'. Thus, even though our coding style with required braces is not impacted, ending a macro with ';' makes our code harder to port to projects that use brace-less styles. The change should have no semantic impact. I was not able to fully compile-test all of the changes (as some of them are examples of the ugly bit-rotting debug print statements that are completely elided by default, and I didn't want to recompile with the necessary -D witnesses - cleaning those up is left as a bite-sized task for another day); I did, however, audit that for all files touched, all callers of the changed macros DID supply a trailing ';' at the callsite, and did not appear to be used as part of a brace-less conditional. Found mechanically via: $ git grep -B1 'while (0);' | grep -A1 \\\\ Signed-off-by: Eric Blake <eblake@redhat.com> Acked-by: Cornelia Huck <cohuck@redhat.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com> Message-Id: <20171201232433.25193-7-eblake@redhat.com> Reviewed-by: Juan Quintela <quintela@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2017-07-14char: avoid chardevice direct accessAnton Nefedov
frontends should avoid accessing CharDriver struct where possible Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com> Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com> Message-Id: <1499342940-56739-6-git-send-email-anton.nefedov@virtuozzo.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2017-07-14char: add backend hotswap handlerAnton Nefedov
Frontends should have an interface to setup the handler of a backend change. The interface will be used in the next commits Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com> Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com> Message-Id: <1499342940-56739-3-git-send-email-anton.nefedov@virtuozzo.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2017-06-02char: move CharBackend handling in char-fe unitMarc-André Lureau
Move all the frontend struct and methods to a seperate unit. This avoids accidentally mixing backend and frontend calls, and helps with readabilty. Make qemu_chr_replay() a macro shared by both char and char-fe. Export qemu_chr_write(), and use a macro for qemu_chr_write_all() (nb: yes, CharBackend is for char frontend :) Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
2017-06-02chardev: serial & parallel declaration to own headersMarc-André Lureau
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
2017-06-02chardev: move headers to include/chardevMarc-André Lureau
So they are all in one place. The following patch will move serial & parallel declarations to the respective headers. Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
2016-12-27cadence_uart: Check if receiver timeout counter is disabledAndrew Gacek
When register Rcvr_timeout_reg0 (R_RTOR in cadence_uart.c) is set to 0, the receiver timeout counter should be disabled. See page 1801 of "Zynq-7000 AP SoC Technical Reference Manual". This commit adds a such a check before setting the receive timeout interrupt. Signed-off-by: Andrew Gacek <andrew.gacek@gmail.com> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-12-27cadence_uart: Check baud rate generator and divider values on migrationAlistair Francis
The Cadence UART device emulator calculates speed by dividing the baud rate by a 'baud rate generator' & 'baud rate divider' value. The device specification defines these register values to be non-zero and within certain limits. Checks were recently added when writing to these registers but not when restoring from migration. This patch adds checks when restoring from migration to avoid divide by zero errors. Reported-by: Huawei PSIRT <psirt@huawei.com> Signed-off-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 04ae30ed8ee1758cd2d2af880da4d28f74c67738.1481132150.git.alistair.francis@xilinx.com Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-11-07char: cadence: check baud rate generator and divider valuesPrasad J Pandit
The Cadence UART device emulator calculates speed by dividing the baud rate by a 'baud rate generator' & 'baud rate divider' value. The device specification defines these register values to be non-zero and within certain limits. Add checks for these limits to avoid errors like divide by zero. Reported-by: Huawei PSIRT <psirt@huawei.com> Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 1477596278-1470-1-git-send-email-ppandit@redhat.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-10-28char: cadence: correct reset value for baud rate registersPrasad J Pandit
The Cadence UART device emulator stores 'baud rate generator' and 'baud rate divider' values, used in computing speed, in two registers. The device specification defines their range and their reset value. Use their correct value when resetting the device in cadence_uart_reset. Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org> Message-id: 1477378140-2670-1-git-send-email-ppandit@redhat.com Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-10-24char: remove explicit_fe_open, use a set_handlers argumentMarc-André Lureau
No need to keep explicit_fe_open around if it affects only a qemu_chr_fe_set_handlers(). Use an additional argument instead. Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Message-Id: <20161022095318.17775-24-marcandre.lureau@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2016-10-24char: make some qemu_chr_fe skip if no driverMarc-André Lureau
In most cases, front ends do not care about the side effect of CharBackend, so we can simply skip the checks and call the qemu_chr_fe functions even without associated CharDriver. Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Message-Id: <20161022095318.17775-20-marcandre.lureau@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2016-10-24char: use qemu_chr_fe* functions with CharBackend argumentMarc-André Lureau
This also switches from qemu_chr_add_handlers() to qemu_chr_fe_set_handlers(). Note that qemu_chr_fe_set_handlers() now takes the focus when fe_open (qemu_chr_add_handlers() did take the focus) Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Message-Id: <20161022095318.17775-16-marcandre.lureau@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2016-10-24char: rename some frontend functionsMarc-André Lureau
qemu_chr_accept_input() and qemu_chr_disconnect() are only used by frontend, so use qemu_chr_fe prefix. Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Message-Id: <20161022095318.17775-14-marcandre.lureau@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2016-10-24char: replace PROP_CHR with CharBackendMarc-André Lureau
Store the property in a CharBackend instead of CharDriverState*. This also replace systematically chr by chr.chr to access the CharDriverState*. The following patches will replace it with calls to qemu_chr_fe CharBackend functions. Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Message-Id: <20161022095318.17775-12-marcandre.lureau@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2016-06-29Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into stagingPeter Maydell
* serial port fixes (Paolo) * Q35 modeling improvements (Paolo, Vasily) * chardev cleanup improvements (Marc-André) * iscsi bugfix (Peter L.) * cpu_exec patch from multi-arch patches (Peter C.) * pci-assign tweak (Lin Ma) # gpg: Signature made Wed 29 Jun 2016 15:56:30 BST # gpg: using RSA key 0xBFFBD25F78C7AE83 # gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" # gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" # Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1 # Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83 * remotes/bonzini/tags/for-upstream: (35 commits) socket: unlink unix socket on remove socket: add listen feature char: clean up remaining chardevs when leaving vhost-user: disable chardev handlers on close vhost-user-test: fix g_cond_wait_until compat implementation vl: smp_parse: fix regression ich9: implement SCI_IRQ_SEL register ich9: implement ACPI_EN register serial: reinstate watch after migration serial: remove watch on reset char: change qemu_chr_fe_add_watch to return unsigned serial: separate serial_xmit and serial_watch_cb serial: simplify tsr_retry reset serial: make tsr_retry unsigned iscsi: fix assertion in is_sector_request_lun_aligned target-*: Don't redefine cpu_exec() pci-assign: Move "Invalid ROM" error message to pci-assign-load-rom.c vnc: generalize "VNC server running on ..." message scsi: esp: fix migration MC146818 RTC: add GPIO access to output IRQ ... Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-06-29char: change qemu_chr_fe_add_watch to return unsignedPaolo Bonzini
g_source_attach can return any value between 1 and UINT_MAX if you let QEMU run long enough. However, qemu_chr_fe_add_watch can also return a negative errno value when the device is disconnected or does not support chr_add_watch. Change it to return zero to avoid overloading these values. Fix the cadence_uart which asserts in this case (easily obtained with "-serial pty"). Tested-by: Bret Ketchum <bcketchum@gmail.com> Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2016-06-27cadence_uart: Protect against transmit errorsAlistair Francis
If qemu_chr_fe_write() returns an error (represented by a negative number) we should skip incrementing the count and initiating a memmove(). Signed-off-by: Alistair Francis <alistair.francis@xilinx.com> Reported-by: Peter Maydell <peter.maydell@linaro.org> Message-id: 667e5dc534d33338fcfc2471e5aa32fe7cbd13dc.1466546703.git.alistair.francis@xilinx.com Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-06-06hw/char: QOM'ify cadence_uart modelxiaoqiang zhao
* drop qemu_char_get_next_serial and use chardev prop * create cadence_uart_create wrapper function to create cadence_uart_device * change affected board code to use the new way Signed-off-by: xiaoqiang zhao <zxq_yx_007@163.com> Message-id: 1465028065-5855-3-git-send-email-zxq_yx_007@163.com Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-05-19hw: explicitly include qemu/log.hPaolo Bonzini
Move the inclusion out of hw/hw.h, most files do not need it. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2016-04-19cadence_uart: bounds check write offsetMichael S. Tsirkin
cadence_uart_init() initializes an I/O memory region of size 0x1000 bytes. However in uart_write(), the 'offset' parameter (offset within region) is divided by 4 and then used to index the array 'r' of size CADENCE_UART_R_MAX which is much smaller: (0x48/4). If 'offset>>=2' exceeds CADENCE_UART_R_MAX, this will cause an out-of-bounds memory write where the offset and the value are controlled by guest. This will corrupt QEMU memory, in most situations this causes the vm to crash. Fix by checking the offset against the array size. Cc: qemu-stable@nongnu.org Reported-by: 李强 <liqiang6-s@360.cn> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Message-id: 20160418100735.GA517@redhat.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2016-03-22Replaced get_tick_per_sec() by NANOSECONDS_PER_SECONDRutuja Shah
This patch replaces get_ticks_per_sec() calls with the macro NANOSECONDS_PER_SECOND. Also, as there are no callers, get_ticks_per_sec() is then removed. This replacement improves the readability and understandability of code. For example, timer_mod(fdctrl->result_timer, qemu_clock_get_ns(QEMU_CLOCK_VIRTUAL) + (get_ticks_per_sec() / 50)); NANOSECONDS_PER_SECOND makes it obvious that qemu_clock_get_ns matches the unit of the expression on the right side of the plus. Signed-off-by: Rutuja Shah <rutu.shah.26@gmail.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2016-01-29arm: Clean up includesPeter Maydell
Clean up includes so that osdep.h is included first and headers which it implies are not included manually. This commit was created with scripts/clean-includes. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Message-id: 1453832250-766-13-git-send-email-peter.maydell@linaro.org
2015-05-18char: cadence_uart: Split state struct and type into headerPeter Crosthwaite
Create a new header for Cadence UART to allow using the device with modern SoC programming conventions. The state struct needs to be visible to embed the device in SoC containers. Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Tested-by: Alistair Francis <alistair.francis@xilinx.com> Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: 46a0fbd45b6b205f54c4a8c778deb75c77f8abdf.1431381507.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2015-05-18char: cadence_uart: Clean up variable namesPeter Crosthwaite
Clean up some variable names in preparation for migrating the state struct and type cast macro to a public header. The acronym "UART" on it's own is not specific enough to be used in a more global namespace so preface with "cadence". Fix the capitalisation of "uart" in the state type while touching the typename. Preface macros used by the state struct itself with CADENCE_UART so they don't conflict in namespace either. Reviewed-by: Alistair Francis <alistair.francis@xilinx.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com> Tested-by: Alistair Francis <alistair.francis@xilinx.com> Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: 3812b7426c338beae9e082557f3524a99310ddc6.1431381507.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2015-04-02sysbus: Make devices picking up backends unavailable with -deviceMarkus Armbruster
Device models aren't supposed to go on fishing expeditions for backends. They should expose suitable properties for the user to set. For onboard devices, board code sets them. A number of sysbus devices pick up block backends in their init() / instance_init() methods with drive_get_next() instead: sl-nand, milkymist-memcard, pl181, generic-sdhci. Likewise, a number of sysbus devices pick up character backends in their init() / realize() methods with qemu_char_get_next_serial(): cadence_uart, digic-uart, etraxfs,serial, lm32-juart, lm32-uart, milkymist-uart, pl011, stm32f2xx-usart, xlnx.xps-uartlite. All these mistakes are already marked FIXME. See the commit that added these FIXMEs for a more detailed explanation of what's wrong. Fortunately, only machines ppce500 and pseries-* support -device with sysbus devices, and none of the devices above is supported with these machines. Set cannot_instantiate_with_device_add_yet to preserve our luck. Cc: Andrzej Zaborowski <balrogg@gmail.com> Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Cc: Antony Pavlov <antonynpavlov@gmail.com> Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com> Cc: Michael Walle <michael@walle.cc> Signed-off-by: Markus Armbruster <armbru@redhat.com>
2015-04-02hw: Mark devices picking up char backends actively FIXMEMarkus Armbruster
Character devices defined with -serial and -parallel are for board initialization to wire up. Board code examines serial_hds[] and parallel_hds[] to find them, and creates devices with their qdev chardev properties set accordingly. Except a few devices go on a fishing expedition for a suitable backend instead of exposing a chardev property for board code to set: they use serial_hds[] (often via qemu_char_get_next_serial()) or parallel_hds[] in their realize() or init() method to connect to a backend. Picking up backends that way works when the devices are created by board code. But it's inappropriate for -device or device_add. Not only is it inconsistent with how the other characrer device models work (they connect to a backend explicitly identified by a "chardev" property), it breaks when the backend has been picked up by the board or a previous -device / device_add already. Example: $ qemu-system-ppc64 -M bamboo -S -device i82378 -device pc87312 -device pc87312 qemu-system-ppc64: -device pc87312: Property 'isa-parallel.chardev' can't take value 'parallel0', it's in use Mark them with suitable FIXME comments. Cc: Li Guang <lig.fnst@cn.fujitsu.com> Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Cc: Antony Pavlov <antonynpavlov@gmail.com> Cc: "Edgar E. Iglesias" <edgar.iglesias@gmail.com> Cc: Michael Walle <michael@walle.cc> Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Cc: "Andreas Färber" <andreas.faerber@web.de> Signed-off-by: Markus Armbruster <armbru@redhat.com>
2015-03-17cadence_uart: Convert to QOM realize()Alistair Francis
Use DeviceClass::realize() and TypeInfo::instance_init() instead of the deprecated SysBusDevice::init(). Signed-off-by: Alistair Francis <alistair.francis@xilinx.com> Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Signed-off-by: Andreas Färber <afaerber@suse.de>
2015-01-26vmstate: accept QEMUTimer in VMSTATE_TIMER*, add VMSTATE_TIMER_PTR*Paolo Bonzini
Old users of VMSTATE_TIMER* are mechanically changed to VMSTATE_TIMER_PTR variants. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-07-17cadence_uart: check for serial backend before using it.KONRAD Frederic
This checks that s->chr is not NULL before using it. Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com> Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2014-06-30serial: poll the serial console with G_IO_HUPRoger Pau Monne
On FreeBSD polling a master pty while the other end is not connected with G_IO_OUT only results in an endless wait. This is different from the Linux behaviour, that returns immediately. In order to demonstrate this, I have the following example code: http://xenbits.xen.org/people/royger/test_poll.c When executed on Linux: $ ./test_poll In callback On FreeBSD instead, the callback never gets called: $ ./test_poll So, in order to workaround this, poll the source with G_IO_HUP (which makes the code behave the same way on both Linux and FreeBSD). Signed-off-by: Roger Pau Monné <roger.pau@citrix.com> Cc: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Cc: Michael Tokarev <mjt@tls.msk.ru> Cc: "Andreas Färber" <afaerber@suse.de> Cc: Paolo Bonzini <pbonzini@redhat.com> Cc: xen-devel@lists.xenproject.org [Add hw/char/cadence_uart.c too. - Paolo] Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-05-13savevm: Remove all the unneeded version_minimum_id_old (arm)Juan Quintela
After commit 767adce2d, they are redundant. This way we don't assign them except when needed. Once there, there were lots of cases where the ".fields" indentation was wrong: .fields = (VMStateField []) { and .fields = (VMStateField []) { Change all the combinations to: .fields = (VMStateField[]){ The biggest problem (apart from aesthetics) was that checkpatch complained when we copy&pasted the code from one place to another. Signed-off-by: Juan Quintela <quintela@redhat.com> [PMM: fixed minor conflict, corrected commit message typos] Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2014-01-08char/cadence_uart: Implement Tx flow controlPeter Crosthwaite
If the UART back-end blocks, buffer in the Tx FIFO to try again later. This stops the IO-thread busy waiting on char back-ends (which causes all sorts of performance problems). Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: 4bea048b3ab38425701d82ccc1ab92545c26b79c.1388626249.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2014-01-08char/cadence_uart: Delete redundant rx rst logicPeter Crosthwaite
uart_rx_reset() called immediately above already does this. Remove. Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: 05e30826496cf2579084ed801ac0b2c0d0a3071f.1388626249.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2014-01-08char/cadence_uart: Use the TX fifo for transmissionPeter Crosthwaite
Populate the TxFIFO with the Tx data before sending. Prepares support for proper Tx flow control implementation. Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: bdf7f8af2ef02839bea18665701bc2612f7baa6f.1388626249.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2014-01-08char/cadence_uart: Fix can_receive logicPeter Crosthwaite
The can_receive logic was only taking into account the RxFIFO occupancy. RxFIFO population is only used for the echo and normal modes however. Improve the logic to correctly return the true number of receivable characters based on the current mode: Normal mode: RxFIFO vacancy. Remote loopback: TxFIFO vacancy. Echo mode: The min of the TxFIFO and RxFIFO vacancies. Local Loopback: Return non-zero (to implement droppage) Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Message-id: 36a58440c9ca5080151e95765c2c81342de8a8df.1388626249.git.peter.crosthwaite@xilinx.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
generated by cgit v1.2.3 (git 2.26.2) at 2024-12-04 20:30:25 +0000