aboutsummaryrefslogtreecommitdiff
path: root/hw/arm
AgeCommit message (Collapse)Author
2022-09-29hw/arm/virt: Fix devicetree warning about the root nodeJean-Philippe Brucker
The devicetree specification requires a 'model' property in the root node. Fix the corresponding dt-validate warning: /: 'model' is a required property From schema: dtschema/schemas/root-node.yaml Use the same name for model as for compatible. The specification recommends that 'compatible' follows the format 'manufacturer,model' and 'model' follows the format 'manufacturer,model-number'. Since our 'compatible' doesn't observe this, 'model' doesn't really need to either. Signed-off-by: Jean-Philippe Brucker <jean-philippe@linaro.org> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Eric Auger <eric.auger@redhat.com> Message-id: 20220927100347.176606-2-jean-philippe@linaro.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2022-09-29hw/arm/xlnx-zynqmp: Connect ZynqMP's USB controllersFrancisco Iglesias
Connect ZynqMP's USB controllers. Signed-off-by: Francisco Iglesias <francisco.iglesias@amd.com> Acked-by: Alistair Francis <alistair.francis@wdc.com> Message-id: 20220920081517.25401-1-frasse.iglesias@gmail.com Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2022-09-14target/arm: Make boards pass base address to armv7m_load_kernel()Peter Maydell
Currently armv7m_load_kernel() takes the size of the block of memory where it should load the initial guest image, but assumes that it should always load it at address 0. This happens to be true of all our M-profile boards at the moment, but it isn't guaranteed to always be so: M-profile CPUs can be configured (via init-svtor and init-nsvtor, which match equivalent hardware configuration signals) to have the initial vector table at any address, not just zero. (For instance the Teeny board has the boot ROM at address 0x0200_0000.) Add a base address argument to armv7m_load_kernel(), so that callers now pass in both base address and size. All the current callers pass 0, so this is not a behaviour change. Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Message-Id: <20220823160417.3858216-3-peter.maydell@linaro.org> Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
2022-09-14target/arm: Remove useless TARGET_BIG_ENDIAN check in armv7m_load_kernel()Peter Maydell
Arm system emulation targets always have TARGET_BIG_ENDIAN clear, so there is no need to have handling in armv7m_load_kernel() for the case when it is defined. Remove the unnecessary code. Side notes: * our M-profile implementation is always little-endian (that is, it makes the IMPDEF choice that the read-only AIRCR.ENDIANNESS is 0) * if we did want to handle big-endian ELF files here we should do it the way that hw/arm/boot.c:arm_load_elf() does, by looking at the ELF header to see what endianness the file itself is Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Message-Id: <20220823160417.3858216-2-peter.maydell@linaro.org> Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
2022-09-14target/arm: Add cortex-a35Hao Wu
Add cortex A35 core and enable it for virt board. Signed-off-by: Hao Wu <wuhaotsh@google.com> Reviewed-by: Joe Komlodi <komlodi@google.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Message-Id: <20220819002015.1663247-1-wuhaotsh@google.com> Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
2022-08-25hw: Add compat machines for 7.2Cornelia Huck
Add 7.2 machine types for arm/i440fx/m68k/q35/s390x/spapr. Signed-off-by: Cornelia Huck <cohuck@redhat.com> Reviewed-by: Daniel Henrique Barboza <danielhb413@gmail.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Message-Id: <20220727121755.395894-1-cohuck@redhat.com> [thuth: fixed conflict with pcmc->legacy_no_rng_seed] Signed-off-by: Thomas Huth <thuth@redhat.com>
2022-08-12hw/arm/virt-acpi-build: Present the GICR structure properly for GICv4Zenghui Yu
With the introduction of the new TCG GICv4, build_madt() is badly broken as we do not present any GIC Redistributor structure in MADT for GICv4 guests, so that they have no idea about where the Redistributor register frames are. This fixes a Linux guest crash at boot time with ACPI enabled and '-machine gic-version=4'. While at it, let's convert the remaining hard coded gic_version into enumeration VIRT_GIC_VERSION_2 for consistency. Signed-off-by: Zenghui Yu <yuzenghui@huawei.com> Message-id: 20220812022018.1069-1-yuzenghui@huawei.com Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2022-08-01Merge tag 'pull-aspeed-20220801' of https://github.com/legoater/qemu into ↵Richard Henderson
staging aspeed queue: * Fix ownership of RAM regions on the fby35 machine # -----BEGIN PGP SIGNATURE----- # # iQIzBAABCAAdFiEEoPZlSPBIlev+awtgUaNDx8/77KEFAmLn1N8ACgkQUaNDx8/7 # 7KHaVA//eh5wIZKeg1Qit8dhVoPXcO7b97KFpBreyCkfdREJpoLjoFe4y+rnKhnL # tJm6qx1YG5s0UN/ODcy4TyKV9CkpcjsRZ+BHuZ+jjiz3WzuarZUTbZx1jVSJP6z0 # xcXc3CucKe/yyidGV1gKGiWetuXv2F6nYHzfvJ4auei6Rga8rwmiN7Rqf3Qfh6Lw # Islj/9axfLxGzuMV85uuRZdRrrlmTOjDgnF4mxwVXRrxjtLIaAbzKT6mc1p1FUry # cuE7bDjbZoT7ftBn5y4gQXV38M3XcWzB1KvzMslldkccU7cTbJg8620KSNiscOkJ # 03xEJiBJoAzy/X1PUmEODNYUV8a19xcsXEyqaRQiyYtO1XMBDcNkSaiaFacOnhFT # UxabJf3qvzf1QwAmgxGUdbR5usNXsr8Yrnpf1lew7Mvr3SwOYVXqb/JPp+j7uoV3 # CVvvTFZm+hBQghaHC0wHBX+C3aLsTis4Jppn5loulo6fb9KZiosj2kPRwEIetVkt # ZgkBOLWRWtizdWKM7HImt7F+v/r7ClFlwAIJj8QQV0HTtVZ+gM6MXWj5oczKENJ8 # vPkoP6AUoOWzKFEhBU5XtQ9DdwPSP9m6zAZXl4LD17tVPUPpsuSEDaxhH5hAEnIR # 39Mgx7hoK0uLHhM02RrNodD/NDmrZCPV3PwZ979z0Q/C8dttRkY= # =hAJg # -----END PGP SIGNATURE----- # gpg: Signature made Mon 01 Aug 2022 06:27:59 AM PDT # gpg: using RSA key A0F66548F04895EBFE6B0B6051A343C7CFFBECA1 # gpg: Good signature from "Cédric Le Goater <clg@kaod.org>" [undefined] # gpg: WARNING: This key is not certified with a trusted signature! # gpg: There is no indication that the signature belongs to the owner. # Primary key fingerprint: A0F6 6548 F048 95EB FE6B 0B60 51A3 43C7 CFFB ECA1 * tag 'pull-aspeed-20220801' of https://github.com/legoater/qemu: aspeed/fby35: Fix owner of the BMC RAM memory region aspeed: Remove unused fields from AspeedMachineState Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
2022-08-01aspeed/fby35: Fix owner of the BMC RAM memory regionCédric Le Goater
A MachineState object is used as a owner of the RAM region and this asserts in memory_region_init_ram() when QEMU is built with CONFIG_QOM_CAST_DEBUG : /* This will assert if owner is neither NULL nor a DeviceState. * We only want the owner here for the purposes of defining a * unique name for migration. TODO: Ideally we should implement * a naming scheme for Objects which are not DeviceStates, in * which case we can relax this restriction. */ owner_dev = DEVICE(owner); Use the BMC and BIC objects as the owners of their memory regions. Cc: Peter Delevoryas <peter@pjd.dev> Fixes: 778e14cc5cd5 ("aspeed: Add AST2600 (BMC) to fby35") Reviewed-by: Peter Delevoryas <peter@pjd.dev> Message-Id: <20220727102714.803041-3-clg@kaod.org> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-08-01aspeed: Remove unused fields from AspeedMachineStateCédric Le Goater
Fixes: 346160cbf2af ("aspeed: Set the dram container at the SoC level") Message-Id: <20220727102714.803041-2-clg@kaod.org> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-08-01trivial: Fix duplicated wordsThomas Huth
Some files wrongly contain the same word twice in a row. One of them should be removed or replaced. Message-Id: <20220722145859.1952732-1-thuth@redhat.com> Signed-off-by: Thomas Huth <thuth@redhat.com>
2022-07-18Align Raspberry Pi DMA interrupts with Linux DTSAndrey Makarov
There is nothing in the specs on DMA engine interrupt lines: it should have been in the "BCM2835 ARM Peripherals" datasheet but the appropriate "ARM peripherals interrupt table" (p.113) is nearly empty. All Raspberry Pi models 1-3 (based on bcm2835) have Linux device tree (arch/arm/boot/dts/bcm2835-common.dtsi +25): /* dma channel 11-14 share one irq */ This information is repeated in the driver code (drivers/dma/bcm2835-dma.c +1344): /* * in case of channel >= 11 * use the 11th interrupt and that is shared */ In this patch channels 0--10 and 11--14 are handled separately. Signed-off-by: Andrey Makarov <andrey.makarov@auriga.com> Message-id: 20220716113210.349153-1-andrey.makarov@auriga.com [PMM: fixed checkpatch nits] Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2022-07-14aspeed: Add fby35-bmc slot GPIO'sPeter Delevoryas
Signed-off-by: Peter Delevoryas <peter@pjd.dev> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220712023219.41065-4-peter@pjd.dev> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-07-14aspeed: Add AST1030 (BIC) to fby35Peter Delevoryas
With the BIC, the easiest way to run everything is to create two pty's for each SoC and reserve stdin/stdout for the monitor: wget https://github.com/facebook/openbmc/releases/download/openbmc-e2294ff5d31d/fby35.mtd wget https://github.com/peterdelevoryas/OpenBIC/releases/download/oby35-cl-2022.13.01/Y35BCL.elf qemu-system-arm -machine fby35 \ -drive file=fby35.mtd,format=raw,if=mtd \ -device loader,file=fby35.mtd,addr=0,cpu-num=0 \ -serial pty -serial pty -serial mon:stdio -display none -S screen /dev/ttys0 screen /dev/ttys1 (qemu) c This commit only adds the the first server board's Bridge IC, but in the future we'll try to include the other three server board Bridge IC's too. Signed-off-by: Peter Delevoryas <peter@pjd.dev> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220705191400.41632-9-peter@pjd.dev> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-07-14aspeed: fby35: Add a bootrom for the BMCCédric Le Goater
The BMC boots from the first flash device by fetching instructions from the flash contents. Add an alias region on 0x0 for this purpose. There are currently performance issues with this method (TBs being flushed too often), so as a faster alternative, install the flash contents as a ROM in the BMC memory space. See commit 1a15311a12fa ("hw/arm/aspeed: add a 'execute-in-place' property to boot directly from CE0") Signed-off-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Peter Delevoryas <peter@pjd.dev> [ clg: blk_pread() fixes ] Message-Id: <20220705191400.41632-8-peter@pjd.dev> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-07-14aspeed: Add AST2600 (BMC) to fby35Peter Delevoryas
You can test booting the BMC with both '-device loader' and '-drive file'. This is necessary because of how the fb-openbmc boot sequence works (jump to 0x20000000 after U-Boot SPL). wget https://github.com/facebook/openbmc/releases/download/openbmc-e2294ff5d31d/fby35.mtd qemu-system-arm -machine fby35 -nographic \ -device loader,file=fby35.mtd,addr=0,cpu-num=0 -drive file=fby35.mtd,format=raw,if=mtd Signed-off-by: Peter Delevoryas <peter@pjd.dev> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220705191400.41632-7-peter@pjd.dev> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-07-14aspeed: Add fby35 skeletonPeter Delevoryas
Signed-off-by: Peter Delevoryas <peter@pjd.dev> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220705191400.41632-6-peter@pjd.dev> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-07-14aspeed: Make aspeed_board_init_flashes publicPeter Delevoryas
Signed-off-by: Peter Delevoryas <peter@pjd.dev> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220705191400.41632-5-peter@pjd.dev> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-07-14aspeed: Refactor UART init for multi-SoC machinesPeter Delevoryas
This change moves the code that connects the SoC UART's to serial_hd's to the machine. It makes each UART a proper child member of the SoC, and then allows the machine to selectively initialize the chardev for each UART with a serial_hd. This should preserve backwards compatibility, but also allow multi-SoC boards to completely change the wiring of serial devices from the command line to specific SoC UART's. This also removes the uart-default property from the SoC, since the SoC doesn't need to know what UART is the "default" on the machine anymore. I tested this using the images and commands from the previous refactoring, and another test image for the ast1030: wget https://github.com/facebook/openbmc/releases/download/v2021.49.0/fuji.mtd wget https://github.com/facebook/openbmc/releases/download/v2021.49.0/wedge100.mtd wget https://github.com/peterdelevoryas/OpenBIC/releases/download/oby35-cl-2022.13.01/Y35BCL.elf Fuji uses UART1: qemu-system-arm -machine fuji-bmc \ -drive file=fuji.mtd,format=raw,if=mtd \ -nographic ast2600-evb uses uart-default=UART5: qemu-system-arm -machine ast2600-evb \ -drive file=fuji.mtd,format=raw,if=mtd \ -serial null -serial mon:stdio -display none Wedge100 uses UART3: qemu-system-arm -machine palmetto-bmc \ -drive file=wedge100.mtd,format=raw,if=mtd \ -serial null -serial null -serial null \ -serial mon:stdio -display none AST1030 EVB uses UART5: qemu-system-arm -machine ast1030-evb \ -kernel Y35BCL.elf -nographic Fixes: 6827ff20b2975 ("hw: aspeed: Init all UART's with serial devices") Signed-off-by: Peter Delevoryas <peter@pjd.dev> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220705191400.41632-4-peter@pjd.dev> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-07-14aspeed: Create SRAM name from first CPU indexPeter Delevoryas
To support multiple SoC's running simultaneously, we need a unique name for each RAM region. DRAM is created by the machine, but SRAM is created by the SoC, since in hardware it is part of the SoC's internals. We need a way to uniquely identify each SRAM region though, for VM migration. Since each of the SoC's CPU's has an index which identifies it uniquely from other CPU's in the machine, we can use the index of any of the CPU's in the SoC to uniquely identify differentiate the SRAM name from other SoC SRAM's. In this change, I just elected to use the index of the first CPU in each SoC. Signed-off-by: Peter Delevoryas <peter@pjd.dev> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220705191400.41632-3-peter@pjd.dev> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-07-12block: Change blk_{pread,pwrite}() param orderAlberto Faria
Swap 'buf' and 'bytes' around for consistency with blk_co_{pread,pwrite}(), and in preparation to implement these functions using generated_co_wrapper. Callers were updated using this Coccinelle script: @@ expression blk, offset, buf, bytes, flags; @@ - blk_pread(blk, offset, buf, bytes, flags) + blk_pread(blk, offset, bytes, buf, flags) @@ expression blk, offset, buf, bytes, flags; @@ - blk_pwrite(blk, offset, buf, bytes, flags) + blk_pwrite(blk, offset, bytes, buf, flags) It had no effect on hw/block/nand.c, presumably due to the #if, so that file was updated manually. Overly-long lines were then fixed by hand. Signed-off-by: Alberto Faria <afaria@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Reviewed-by: Hanna Reitz <hreitz@redhat.com> Message-Id: <20220705161527.1054072-4-afaria@redhat.com> Signed-off-by: Hanna Reitz <hreitz@redhat.com>
2022-07-12block: Add a 'flags' param to blk_pread()Alberto Faria
For consistency with other I/O functions, and in preparation to implement it using generated_co_wrapper. Callers were updated using this Coccinelle script: @@ expression blk, offset, buf, bytes; @@ - blk_pread(blk, offset, buf, bytes) + blk_pread(blk, offset, buf, bytes, 0) It had no effect on hw/block/nand.c, presumably due to the #if, so that file was updated manually. Overly-long lines were then fixed by hand. Signed-off-by: Alberto Faria <afaria@redhat.com> Reviewed-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Greg Kurz <groug@kaod.org> Reviewed-by: Hanna Reitz <hreitz@redhat.com> Message-Id: <20220705161527.1054072-3-afaria@redhat.com> Signed-off-by: Hanna Reitz <hreitz@redhat.com>
2022-07-07hw/arm/virt: dt: add rng-seed propertyJason A. Donenfeld
In 60592cfed2 ("hw/arm/virt: dt: add kaslr-seed property"), the kaslr-seed property was added, but the equally as important rng-seed property was forgotten about, which has identical semantics for a similar purpose. This commit implements it in exactly the same way as kaslr-seed. It then changes the name of the disabling option to reflect that this has more to do with randomness vs determinism, rather than something particular about kaslr. Cc: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> [PMM: added deprecated.rst section for the deprecation] Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2022-06-30hw/misc/aspeed: Add PECI controllerPeter Delevoryas
This introduces a really basic PECI controller that responses to commands by always setting the response code to success and then raising an interrupt to indicate the command is done. This helps avoid getting hit with constant errors if the driver continuously attempts to send a command and keeps timing out. The AST2400 and AST2500 only included registers up to 0x5C, not 0xFC. They supported PECI 1.1, 2.0, and 3.0. The AST2600 and AST1030 support PECI 4.0, which includes more read/write buffer registers from 0x80 to 0xFC to support 64-byte mode. This patch doesn't attempt to handle that, or to create a different version of the controller for the different generations, since it's only implementing functionality that is common to all generations. The basic sequence of events is that the firmware will read and write to various registers and then trigger a command by setting the FIRE bit in the command register (similar to the I2C controller). Then the firmware waits for an interrupt from the PECI controller, expecting the interrupt status register to be filled in with info on what happened. If the command was transmitted and received successfully, then response codes from the host CPU will be found in the data buffer registers. Signed-off-by: Peter Delevoryas <pdel@fb.com> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220630045133.32251-12-me@pjd.dev> [ clg: s/sysbus_mmio_map/aspeed_mmio_map/ ] Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-30hw/i2c: add asynchronous sendKlaus Jensen
Add an asynchronous version of i2c_send() that requires the slave to explicitly acknowledge on the bus with i2c_ack(). The current master must use the new i2c_start_send_async() to indicate that it wants to do an asynchronous transfer. This allows the i2c core to check if the target slave supports this or not. This approach relies on adding a new enum i2c_event member, which is why a bunch of other devices needs changes in their event handling switches. Signed-off-by: Klaus Jensen <k.jensen@samsung.com> Message-Id: <20220601210831.67259-5-its@irrelevant.dk> Signed-off-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220630045133.32251-6-me@pjd.dev> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-30hw/arm/aspeed: firework: add I2C MUXes for VR channelsJae Hyun Yoo
Add 2-level cascaded I2C MUXes for SOC VR channels into the Firework machine. Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220627154703.148943-8-quic_jaehyoo@quicinc.com> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-30hw/arm/aspeed: firework: Add Thermal DiodesMaheswara Kurapati
Add Thermal Diodes for Firework machine. Signed-off-by: Maheswara Kurapati <quic_mkurapat@quicinc.com> Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220627154703.148943-7-quic_jaehyoo@quicinc.com> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-30hw/arm/aspeed: Add MAX31785 Fan controllersMaheswara Kurapati
Add MAX31785 fan controllers in machines so that the Linux driver populates the sysfs interface. Firework has two MAX31785 Fan controllers at 0x52, and 0x54 on bus 9. Witherspoon has one at 0x52 on bus 3. Rainier has one at 0x52 on bus 7. Signed-off-by: Maheswara Kurapati <quic_mkurapat@quicinc.com> Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220627154703.148943-6-quic_jaehyoo@quicinc.com> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-30hw/arm/aspeed: add Qualcomm Firework BMC machineGraeme Gregory
Add base for Qualcomm Firework BMC machine. Signed-off-by: Graeme Gregory <quic_ggregory@quicinc.com> Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220627154703.148943-3-quic_jaehyoo@quicinc.com> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-30hw/arm/aspeed: add support for the Qualcomm DC-SCM v1 boardJae Hyun Yoo
Add qcom-dc-scm-v1 board support. Signed-off-by: Jae Hyun Yoo <quic_jaehyoo@quicinc.com> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220627154703.148943-2-quic_jaehyoo@quicinc.com> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-30aspeed: Remove use of qemu_get_cpuPeter Delevoryas
Signed-off-by: Peter Delevoryas <pdel@fb.com> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220624003701.1363500-6-pdel@fb.com> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-30aspeed: Map unimplemented devices in SoC memoryPeter Delevoryas
Signed-off-by: Peter Delevoryas <pdel@fb.com> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220624003701.1363500-5-pdel@fb.com> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-30aspeed: Remove usage of sysbus_mmio_mapPeter Delevoryas
sysbus_mmio_map maps devices into "get_system_memory()". With the new SoC memory attribute, we want to make sure that each device is mapped into the SoC memory. In single SoC machines, the SoC memory is the same as "get_system_memory()", but in multi SoC machines it will be different. Signed-off-by: Peter Delevoryas <pdel@fb.com> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220624003701.1363500-4-pdel@fb.com> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-30aspeed: Add memory property to Aspeed SoCPeter Delevoryas
Multi-SoC machines can use this property to specify a memory container for each SoC. Single SoC machines will just specify get_system_memory(). Signed-off-by: Peter Delevoryas <pdel@fb.com> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220624003701.1363500-3-pdel@fb.com> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-30aspeed: Set CPU memory property explicitlyPeter Delevoryas
Signed-off-by: Peter Delevoryas <pdel@fb.com> Message-Id: <20220624003701.1363500-2-pdel@fb.com> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-30aspeed: Set the dram container at the SoC levelCédric Le Goater
Currently, the Aspeed machines allocate a ram container region in which the machine ram region is mapped. See commit ad1a9782186d ("aspeed: add a RAM memory region container"). An extra region is mapped after ram in the ram container to catch invalid access done by FW. That's how FW determines the size of ram. See commit ebe31c0a8ef7 ("aspeed: add a max_ram_size property to the memory controller"). Let's move all the logic under the SoC where it should be. It will also ease the work on multi SoC support. Reviewed-by: Peter Delevoryas <pdel@fb.com> Message-Id: <20220623202123.3972977-1-clg@kaod.org> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-27target/arm: Extend arm_pamax to more than aarch64Richard Henderson
Move the code from hw/arm/virt.c that is supposed to handle v7 into the one function. Signed-off-by: Richard Henderson <richard.henderson@linaro.org> Reported-by: He Zhe <zhe.he@windriver.com> Message-id: 20220619001541.131672-2-richard.henderson@linaro.org Reviewed-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2022-06-22aspeed: Add I2C buses to AST1030 modelTroy Lee
Instantiate the I2C buses in AST1030 model and create two slave device for ast1030-evb. Signed-off-by: Troy Lee <troy_lee@aspeedtech.com> Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com> Signed-off-by: Steven Lee <steven_lee@aspeedtech.com> Reviewed-by: Joel Stanley <joel@jms.id.au> [ clg : - adapted to current AST1030 upstream models - changed AST2600 to AST1030 in comment - fixed typo in commit log ] Message-Id: <20220324100439.478317-3-troy_lee@aspeedtech.com> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-22aspeed: Remove fake RTC device on ast2500-evbCédric Le Goater
The board has no such device. It might have been useful for some tests in the past, it's not anymore and the same can be achieved on the command line. Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-06-10hw/core/loader: return image sizes as ssize_tJamie Iles
Various loader functions return an int which limits images to 2GB which is fine for things like a BIOS/kernel image, but if we want to be able to load memory images or large ramdisks then any file over 2GB would silently fail to load. Cc: Luc Michel <lmichel@kalray.eu> Signed-off-by: Jamie Iles <jamie@nuviainc.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com> Reviewed-by: Luc Michel <lmichel@kalray.eu> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Message-Id: <20211111141141.3295094-2-jamie@nuviainc.com> Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
2022-06-08xlnx-zynqmp: fix the irq mapping for the display port and its dmaFrederic Konrad
When the display port has been initially implemented the device driver wasn't using interrupts. Now that the display port driver waits for vblank interrupt it has been noticed that the irq mapping is wrong. So use the value from the linux device tree and the ultrascale+ reference manual. Signed-off-by: Frederic Konrad <fkonrad@amd.com> Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com> Acked-by: Alistair Francis <alistair.francis@wdc.com> Message-id: 20220601172353.3220232-5-fkonrad@xilinx.com [PMM: refold lines in commit message] Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2022-05-25hw/arm/aspeed: Add i2c devices for AST2600 EVBHoward Chiu
Add EEPROM and LM75 temperature sensor according to hardware schematic Signed-off-by: Howard Chiu <howard_chiu@aspeedtech.com> Reviewed-by: Cédric Le Goater <clg@kaod.org> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-05-25hw/gpio: Add ASPEED GPIO model for AST1030Jamin Lin
AST1030 integrates one set of Parallel GPIO Controller with maximum 151 control pins, which are 21 groups (A~U, exclude pin: M6 M7 Q5 Q6 Q7 R0 R1 R4 R5 R6 R7 S0 S3 S4 S5 S6 S7 ) and the group T and U are input only. Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220525053444.27228-3-jamin_lin@aspeedtech.com> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-05-25hw: aspeed: Init all UART's with serial devicesPeter Delevoryas
Background: AspeedMachineClass.uart_default specifies the serial console UART, which usually corresponds to the "stdout-path" in the device tree. The default value is UART5, since most boards use UART5 for this: amc->uart_default = ASPEED_DEV_UART5; Users can override AspeedMachineClass.uart_default in their board's machine class init to specify something besides UART5. For example, for fuji-bmc: amc->uart_default = ASPEED_DEV_UART1; We only connect this one UART, of the 5 UART's on the AST2400 and AST2500 and the 13 UART's on the AST2600 and AST1030, to a serial device that QEMU users can use. None of the other UART's are initialized, and the only way to override this attribute is by creating a specialized board definition, requiring QEMU source code changes and rebuilding. The result of this is that if you want to get serial console output on a board that uses UART3, you need to add a board definition. This was encountered by Zev in OpenBMC. [1] Changes: This commit initializes all of the UART's present on each Aspeed chip with serial devices and allows the QEMU user to connect as many or few as they like to serial devices. For example, you can still run QEMU and just connect stdout to the machine's default UART, without specifying any additional serial devices: qemu-system-arm -machine fuji-bmc \ -drive file=fuji.mtd,format=raw,if=mtd \ -nographic However, if you don't want to add a special machine definition, you can now manually configure UART1 to connect to stdout and get serial console output, even if the machine's default is UART5: qemu-system-arm -machine ast2600-evb \ -drive file=fuji.mtd,format=raw,if=mtd \ -serial null -serial mon:stdio -display none In the example above, the first "-serial null" argument is connected to UART5, and "-serial mon:stdio" is connected to UART1. Another example: you can get serial console output from Wedge100, which uses UART3, by reusing the palmetto AST2400 machine and rewiring the serial device arguments: qemu-system-arm -machine palmetto-bmc \ -drive file=wedge100.mtd,format=raw,if=mtd \ -serial null -serial null -serial null \ -serial mon:stdio -display none There is a slight change in behavior introduced with this change: now, each UART's memory-mapped IO region will have a serial device model connected to it. Previously, all reads and writes to those regions would be ineffective and return zero values, but now some values will be nonzero, even when the user doesn't connect a serial device backend (like a socket, file, etc). For example, the line status register might indicate that the transmit buffer is empty now, whereas previously it might have always indicated it was full. [1] https://lore.kernel.org/openbmc/YnzGnWjkYdMUUNyM@hatter.bewilderbeest.net/ [2] https://github.com/facebook/openbmc/releases/download/v2021.49.0/fuji.mtd [3] https://github.com/facebook/openbmc/releases/download/v2021.49.0/wedge100.mtd Signed-off-by: Peter Delevoryas <pdel@fb.com> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220516062328.298336-6-pdel@fb.com> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-05-25hw: aspeed: Introduce common UART init functionPeter Delevoryas
Signed-off-by: Peter Delevoryas <pdel@fb.com> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220516062328.298336-5-pdel@fb.com> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-05-25hw: aspeed: Ensure AST1030 respects uart-defaultPeter Delevoryas
The AST1030 machine initialization was not respecting the Aspeed SoC property "uart-default", which specifies which UART should be connected to the first serial device, it was just always connecting UART5. This doesn't change any behavior, because the default value for "uart-default" is UART5, but it makes it possible to override this in new machine definitions using the AST1030. Signed-off-by: Peter Delevoryas <pdel@fb.com> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220516062328.298336-4-pdel@fb.com> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-05-25hw: aspeed: Add uarts_num SoC attributePeter Delevoryas
AST2400 and AST2500 have 5 UART's, while the AST2600 and AST1030 have 13. Signed-off-by: Peter Delevoryas <pdel@fb.com> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220516062328.298336-3-pdel@fb.com> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-05-25hw: aspeed: Add missing UART'sPeter Delevoryas
This adds the missing UART memory and IRQ mappings for the AST2400, AST2500, AST2600, and AST1030. This also includes the new UART interfaces added in the AST2600 and AST1030 from UART6 to UART13. The addresses and interrupt numbers for these two later chips are identical. Signed-off-by: Peter Delevoryas <pdel@fb.com> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220516062328.298336-2-pdel@fb.com> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-05-25aspeed: Introduce a get_irq AspeedSoCClass methodCédric Le Goater
and make routine aspeed_soc_get_irq() common to all SoCs. This will be useful to share code. Cc: Jamin Lin <jamin_lin@aspeedtech.com> Cc: Peter Delevoryas <pdel@fb.com> Reviewed-by: Peter Delevoryas <pdel@fb.com> Signed-off-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220516055620.2380197-1-clg@kaod.org> Signed-off-by: Cédric Le Goater <clg@kaod.org>
2022-05-25hw/arm/aspeed: Add fby35 machine typePeter Delevoryas
Add the 'fby35-bmc' machine type based on the kernel DTS[1] and userspace i2c setup scripts[2]. Undefined values are inherited from the AST2600-EVB. Reference images can be found in Facebook OpenBMC Github Release assets as "fby35.mtd". [3] You can boot the reference images as follows (fby35 uses dual-flash): qemu-system-arm -machine fby35-bmc \ -drive file=fby35.mtd,format=raw,if=mtd \ -drive file=fby35.mtd,format=raw,if=mtd \ -nographic [1] https://github.com/facebook/openbmc-linux/blob/412d5053258007117e94b1e36015aefc1301474b/arch/arm/boot/dts/aspeed-bmc-facebook-fby35.dts [2] https://github.com/facebook/openbmc/blob/e2294ff5d31dd65c248fe396a385286d6d5c463d/meta-facebook/meta-fby35/recipes-fby35/plat-utils/files/setup-dev.sh [3] https://github.com/facebook/openbmc/releases Signed-off-by: Peter Delevoryas <pdel@fb.com> Reviewed-by: Cédric Le Goater <clg@kaod.org> Message-Id: <20220503225925.1798324-2-pdel@fb.com> Signed-off-by: Cédric Le Goater <clg@kaod.org>
generated by cgit v1.2.3 (git 2.26.2) at 2025-03-15 20:29:18 +0000