| Age | Commit message (Collapse) | Author |
|---|
|
staging
# gpg: Signature made Mon 29 Jan 2018 08:14:19 GMT
# gpg: using RSA key 0xEF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
MAINTAINERS: update Dmitry Fleytman email
qemu-doc: Get rid of "vlan=X" example in the documentation
net: Allow netdevs to be used with 'hostfwd_add' and 'hostfwd_remove'
net: Allow hubports to connect to other netdevs
colo: compare the packet based on the tcp sequence number
colo: modified the payload compare function
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
It does not make much sense to limit these commands to the legacy 'vlan'
concept only, they should work with the modern netdevs, too. So now
it is possible to use this command with one, two or three parameters.
With one parameter, the command installs a hostfwd rule on the default
"user" network:
hostfwd_add tcp:...
With two parameters, the command installs a hostfwd rule on a netdev
(that's the new way of using this command):
hostfwd_add netdev_id tcp:...
With three parameters, the command installs a rule on a 'vlan' (aka hub):
hostfwd_add hub_id name tcp:...
Same applies to the hostfwd_remove command now.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Since everything else about the nbd-server-* QMP commands is
accessible from HMP, we might as well make removing an export
available as well. For now, I went with a bool flag rather
than a mode string for choosing between safe (default) and
hard modes.
Signed-off-by: Eric Blake <eblake@redhat.com>
Message-Id: <20180125144557.25502-1-eblake@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Eric Blake <eblake@redhat.com>
|
|
Extend the flexibility of the previous QMP patch to also work
in HMP.
Signed-off-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20180109192802.17167-1-eblake@redhat.com>
|
|
It's easy to use device_add and device_del as replacement instead.
The usb_add and usb_del commands are deprecated since QEMU 2.10,
and nobody complained that they are still needed, so let's get rid
of them now to make the HMP interface a little bit less overloaded.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <1512073140-17672-1-git-send-email-thuth@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
|
|
HMP equivalent to the just added migrate-continue
Unpause a migrate paused at a given state.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
|
|
staging
s390x/kvm/migration/cpumodel: fixes, enhancements and cleanups
- add a network boot rom for s390 (Thomas Huth)
- migration of storage attributes like the CMMA used/unused state
- PCI related enhancements - full support for aen, ais and zpci
- migration support for css with vmstates (Halil Pasic)
- cpu model enhancements for cpu features
- guarded storage support
# gpg: Signature made Fri 14 Jul 2017 11:33:04 BST
# gpg: using RSA key 0x117BBC80B5A61C7C
# gpg: Good signature from "Christian Borntraeger (IBM) <borntraeger@de.ibm.com>"
# Primary key fingerprint: F922 9381 A334 08F9 DBAB FBCA 117B BC80 B5A6 1C7C
* remotes/borntraeger/tags/s390x-20170714: (40 commits)
s390x/gdb: add gs registers
s390x/arch_dump: also dump guarded storage control block
s390x/kvm: enable guarded storage
s390x/kvm: Enable KSS facility for nested virtualization
s390x/cpumodel: add esop/esop2 to z12 model
s390x/cpumodel: we are always in zarchitecture mode
s390x/cpumodel: wire up new hardware features
s390x/flic: migrate ais states
s390x/cpumodel: add zpci, aen and ais facilities
s390x: initialize cpu firstly
pc-bios/s390: rebuild s390-ccw.img
pc-bios/s390: add s390-netboot.img
pc-bios/s390-ccw: Link libnet into the netboot image and do the TFTP load
pc-bios/s390-ccw: Add virtio-net driver code
pc-bios/s390-ccw: Add core files for the network bootloading program
roms/SLOF: Update submodule to latest status
pc-bios/s390-ccw: Add code for virtio feature negotiation
pc-bios/s390-ccw: Remove unused structs from virtio.h
pc-bios/s390-ccw: Move byteswap functions to a separate header
pc-bios/s390-ccw: Add a write() function for stdio
...
Conflicts:
target/s390x/kvm.c
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add an "info" monitor command to non-destructively inspect the state of
the storage attributes of the guest, and a normal command to toggle
migration mode (useful for debugging).
Signed-off-by: Claudio Imbrenda <imbrenda@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
Signed-off-by: Anton Nefedov <anton.nefedov@virtuozzo.com>
Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <1499342940-56739-11-git-send-email-anton.nefedov@virtuozzo.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Now that all encryption keys must be provided upfront via
the QCryptoSecret API and associated block driver properties
there is no need for any explicit encryption handling APIs
in the block layer. Encryption can be handled transparently
within the block driver. We only retain an API for querying
whether an image is encrypted or not, since that is a
potentially useful piece of metadata to report to the user.
Reviewed-by: Alberto Garcia <berto@igalia.com>
Reviewed-by: Max Reitz <mreitz@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-id: 20170623162419.26068-18-berrange@redhat.com
Signed-off-by: Max Reitz <mreitz@redhat.com>
|
|
Sending a break on a serial console can be useful for debugging the
guest. But not all chardev backends support sending breaks (only telnet
and mux do). The chardev-send-break command allows to send a break even
if using other backends.
Signed-off-by: Stefan Fritsch <sf@sfritsch.de>
Acked-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <20170611074817.13621-1-sf@sfritsch.de>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Use 'send a break' in all 3 pieces of text as suggested by eblake
|
|
The commands 'device_add' and 'device_del' should be used
nowadays instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 1495175803-12830-1-git-send-email-thuth@redhat.com
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
The netdev_add and netdev_del commands should be used nowadays instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
These commands are useful when testing machine-check passthrough.
gpa2hva is useful to inject a MADV_HWPOISON madvise from gdb, while
gpa2hpa is useful to inject an error with the mce-inject kernel
module.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1490021158-4469-1-git-send-email-pbonzini@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20170420133058.12911-1-pbonzini@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
|
|
We leave users to choose whatever heartbeat solution they want,
if the heartbeat is lost, or other errors they detect, they can use
experimental command 'x_colo_lost_heartbeat' to tell COLO to do failover,
COLO will do operations accordingly.
For example, if the command is sent to the Primary side,
the Primary side will exit COLO mode, does cleanup work,
and then, PVM will take over the service work. If sent to the Secondary side,
the Secondary side will run failover work, then takes over PVM's service work.
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Eric Blake <eblake@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
|
|
This is no longer necessary now that we aren't using middle mode
anymore.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <20160912091913.15831-12-marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
|
|
The idea is simple - backup is "written-once" data. It is written block
by block and it is large enough. It would be nice to save storage
space and compress it.
The patch adds a flag to the qmp/hmp drive-backup command which enables
block compression. Compression should be implemented in the format driver
to enable this feature.
There are some limitations of the format driver to allow compressed writes.
We can write data only once. Though for backup this is perfectly fine.
These limitations are maintained by the driver and the error will be
reported if we are doing something wrong.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Jeff Cody <jcody@redhat.com>
CC: Markus Armbruster <armbru@redhat.com>
CC: Eric Blake <eblake@redhat.com>
CC: John Snow <jsnow@redhat.com>
CC: Stefan Hajnoczi <stefanha@redhat.com>
CC: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
Signed-off-by: Lluís Vilanova <vilanova@ac.upc.edu>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
Define two new migration parameters to be used with TLS encryption.
The 'tls-creds' parameter provides the ID of an instance of the
'tls-creds' object type, or rather a subclass such as 'tls-creds-x509'.
Providing these credentials will enable use of TLS on the migration
data stream.
If using x509 certificates, together with a migration URI that does
not include a hostname, the 'tls-hostname' parameter provides the
hostname to use when verifying the server's x509 certificate. This
allows TLS to be used in combination with fd: and exec: protocols
where a TCP connection is established by a 3rd party outside of
QEMU.
NB, this requires changing the migrate_set_parameter method in the
HMP to accept a 's' (string) value instead of 'i' (integer). This
is backwards compatible, because the parsing of strings allows the
quotes to be optional, thus any integer is also a valid string.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1461751518-12128-26-git-send-email-berrange@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
|
|
This patch adds an option to the drive_add HMP command to create only a
BlockDriverState without a BlockBackend on top.
The motivation for this is that libvirt needs to specify options to a
migration target (specifically, detect-zeroes). drive-mirror doesn't
allow specifying options, and the proper way to do this is to create the
target BDS separately with blockdev-add (where you can specify options)
and then use blockdev-mirror to that BDS.
However, libvirt can't use blockdev-add as long as it is still
experimental, and we're expecting that it will still take some time, so
we need to resort to drive_add.
The problem with drive_add is that so far it always created a BB, and
BDSes with a BB can't be used as a mirroring target as long as we don't
support multiple BBs per BDS - and while we're working towards that
goal, it's another thing that will still take some time.
So to achieve the goal, the simplest solution to provide the
functionality now without adding one-off options to the mirror QMP
commands is to extend drive_add to create nodes without BBs.
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
Postcopy seems to have survived a cycle with only a few fixes,
and Jiri has the current libvirt wired up and working
( https://www.redhat.com/archives/libvir-list/2016-March/msg00080.html )
so remove the experimental tag.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-Id: <1457690016-9070-3-git-send-email-dgilbert@redhat.com>
Signed-off-by: Amit Shah <amit.shah@redhat.com>
|
|
This patch only adds the interfaces, but does not implement them.
"detach" parameter is made optional, to make sure that all the old
dump-guest-memory requests will still be able to work.
Signed-off-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Message-Id: <1455772616-8668-3-git-send-email-peterx@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Improve the text in both the qapi-schema and hmp help to point out
you need to set the postcopy-ram capability prior to issuing
migrate-start-postcopy.
Also fix the text of the migrate_start_postcopy error that
deals with capabilities.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Acked-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
|
|
Expose the new read-only-mode option of 'blockdev-change-medium' for the
'change' HMP command.
Signed-off-by: Max Reitz <mreitz@redhat.com>
Reviewed-by: Kevin Wolf <kwolf@redhat.com>
Signed-off-by: Kevin Wolf <kwolf@redhat.com>
|
|
Once postcopy is enabled (with migrate_set_capability), the migration
will still start on precopy mode. To cause a transition into postcopy
the:
migrate_start_postcopy
command must be issued. Postcopy will start sometime after this
(when it's next checked in the migration loop).
Issuing the command before migration has started will error,
and issuing after it has finished is ignored.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Juan Quintela <quintela@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
|
|
Currently device_del requires that the client provide the
device short ID. device_add allows devices to be created
without giving an ID, at which point there is no way to
delete them with device_del. The QOM object path, however,
provides an alternative way to identify the devices.
Allowing device_del to accept an object path ensures all
devices are deletable regardless of whether they have an
ID.
(qemu) device_add usb-mouse
(qemu) qom-list /machine/peripheral-anon
device[0] (child<usb-mouse>)
type (string)
(qemu) device_del /machine/peripheral-anon/device[0]
Devices are required to be marked as hotpluggable
otherwise an error is raised
(qemu) device_del /machine/unattached/device[4]
Device 'PIIX3' does not support hotplugging
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1441974836-17476-1-git-send-email-berrange@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
[Commit message touched up, accidental white-space change dropped]
Signed-off-by: Markus Armbruster <armbru@redhat.com>
|
|
It will be easier if you need to add info-commands to edit
only hmp-commands-info.hx, before this had to edit monitor.c and
hmp-commands.hx.
From the build point of view all documentation is saved into
qemu-monitor-info.texi which from now on is used for all user
documentation building.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <1441899541-1856-5-git-send-email-den@openvz.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The table info(information about the system state) closes earlier
and some of its elements are outside(trace-events, rocker, etc). This
can be confusing and lead to additional bugs.
Signed-off-by: Pavel Butsykin <pbutsykin@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <1441899541-1856-4-git-send-email-den@openvz.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Make "info iothreads" available on the HMP monitor.
For example, the results are as follows when executing qemu
command with "-object iothread,id=iothread-1 -object
iothread,id=iothread-2".
(qemu) info iothreads
iothread-1: thread_id=123
iothread-2: thread_id=456
Signed-off-by: Ting Wang <kathy.wangting@huawei.com>
Message-Id: <1435306033-58372-1-git-send-email-kathy.wangting@huawei.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
Reviewed-by: Amos Jianjun Kong <kongjianjun@gmail.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
|
|
into staging
# gpg: Signature made Thu 03 Sep 2015 15:46:52 BST using RSA key ID 81AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
* remotes/stefanha/tags/tracing-pull-request:
trace-events: Add hmp completion
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add completion for the trace event names in the hmp trace-event
command.
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-id: 1439548063-18410-1-git-send-email-dgilbert@redhat.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
Provide an info skeys hmp sub-command to allow the end user to dump a storage
key for a given address. This is useful for guest operating system developers.
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
Add dump-skeys command to the human monitor.
Reviewed-by: Thomas Huth <thuth@linux.vnet.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Jason J. Herne <jjherne@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
Add QMP/HMP support for rocker devices. This is mostly for debugging purposes
to see inside the device's tables and port configurations. Some examples:
(qemu) info rocker sw1
name: sw1
id: 0x0000013512005452
ports: 4
(qemu) info rocker-ports sw1
ena/ speed/ auto
port link duplex neg?
sw1.1 up 10G FD No
sw1.2 up 10G FD No
sw1.3 !ena 10G FD No
sw1.4 !ena 10G FD No
(qemu) info rocker-of-dpa-flows sw1
prio tbl hits key(mask) --> actions
2 60 pport 1 vlan 1 LLDP src 00:02:00:00:02:00 dst 01:80:c2:00:00:0e
2 60 pport 1 vlan 1 ARP src 00:02:00:00:02:00 dst 00:02:00:00:03:00
2 60 pport 2 vlan 2 IPv6 src 00:02:00:00:03:00 dst 33:33:ff:00:00:02 proto 58
3 50 vlan 2 dst 33:33:ff:00:00:02 --> write group 0x32000001 goto tbl 60
2 60 pport 2 vlan 2 IPv6 src 00:02:00:00:03:00 dst 33:33:ff:00:03:00 proto 58
3 50 1 vlan 2 dst 33:33:ff:00:03:00 --> write group 0x32000001 goto tbl 60
2 60 pport 2 vlan 2 ARP src 00:02:00:00:03:00 dst 00:02:00:00:02:00
3 50 2 vlan 2 dst 00:02:00:00:02:00 --> write group 0x02000001 goto tbl 60
2 60 1 pport 2 vlan 2 IP src 00:02:00:00:03:00 dst 00:02:00:00:02:00 proto 1
3 50 2 vlan 1 dst 00:02:00:00:03:00 --> write group 0x01000002 goto tbl 60
2 60 1 pport 1 vlan 1 IP src 00:02:00:00:02:00 dst 00:02:00:00:03:00 proto 1
2 60 pport 1 vlan 1 IPv6 src 00:02:00:00:02:00 dst 33:33:ff:00:00:01 proto 58
3 50 vlan 1 dst 33:33:ff:00:00:01 --> write group 0x31000000 goto tbl 60
2 60 pport 1 vlan 1 IPv6 src 00:02:00:00:02:00 dst 33:33:ff:00:02:00 proto 58
3 50 1 vlan 1 dst 33:33:ff:00:02:00 --> write group 0x31000000 goto tbl 60
1 60 173 pport 2 vlan 2 LLDP src <any> dst 01:80:c2:00:00:0e --> write group 0x02000000
1 60 6 pport 2 vlan 2 IPv6 src <any> dst <any> --> write group 0x02000000
1 60 174 pport 1 vlan 1 LLDP src <any> dst 01:80:c2:00:00:0e --> write group 0x01000000
1 60 174 pport 2 vlan 2 IP src <any> dst <any> --> write group 0x02000000
1 60 6 pport 1 vlan 1 IPv6 src <any> dst <any> --> write group 0x01000000
1 60 181 pport 2 vlan 2 ARP src <any> dst <any> --> write group 0x02000000
1 10 715 pport 2 --> apply new vlan 2 goto tbl 20
1 60 177 pport 1 vlan 1 ARP src <any> dst <any> --> write group 0x01000000
1 60 174 pport 1 vlan 1 IP src <any> dst <any> --> write group 0x01000000
1 10 717 pport 1 --> apply new vlan 1 goto tbl 20
1 0 1432 pport 0(0xffff) --> goto tbl 10
(qemu) info rocker-of-dpa-groups sw1
id (decode) --> buckets
0x32000001 (type L2 multicast vlan 2 index 1) --> groups [0x02000001,0x02000000]
0x02000001 (type L2 interface vlan 2 pport 1) --> pop vlan out pport 1
0x01000002 (type L2 interface vlan 1 pport 2) --> pop vlan out pport 2
0x02000000 (type L2 interface vlan 2 pport 0) --> pop vlan out pport 0
0x01000000 (type L2 interface vlan 1 pport 0) --> pop vlan out pport 0
0x31000000 (type L2 multicast vlan 1 index 0) --> groups [0x01000002,0x01000000]
[Added "query-" prefixes to rocker.json commands as suggested by Eric
Blake <eblake@redhat.com>.
--Stefan]
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Message-id: 1433985681-56138-5-git-send-email-sfeldma@gmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
|
|
All QMP commands use the "new" handler interface (mhandler.cmd_new).
Most HMP commands still use the traditional interface (mhandler.cmd),
but a few use the "new" one. Complicates handle_user_command() for no
gain, so I'm converting these to the traditional interface.
pcie_aer_inject_error's implementation is split into the
hmp_pcie_aer_inject_error() and pcie_aer_inject_error_print(). The
former is a peculiar crossbreed between HMP and QMP handler. On
success, it works like a QMP handler: store QDict through ret_data
parameter, return 0. Printing the QDict is left to
pcie_aer_inject_error_print(). On failure, it works more like an HMP
handler: print error to monitor, return negative number.
To convert to the traditional interface, turn
pcie_aer_inject_error_print() into a command handler wrapping around
hmp_pcie_aer_inject_error(). By convention, this command handler
should be called hmp_pcie_aer_inject_error(), so rename the existing
hmp_pcie_aer_inject_error() to do_pcie_aer_inject_error().
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
|
|
All QMP commands use the "new" handler interface (mhandler.cmd_new).
Most HMP commands still use the traditional interface (mhandler.cmd),
but a few use the "new" one. Complicates handle_user_command() for no
gain, so I'm converting these to the traditional interface.
For device_add, that's easy: just wrap the obvious hmp_device_add()
around do_device_add().
monitor_user_noop() is now unused, drop it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
|
|
All QMP commands use the "new" handler interface (mhandler.cmd_new).
Most HMP commands still use the traditional interface (mhandler.cmd),
but a few use the "new" one. Complicates handle_user_command() for no
gain, so I'm converting these to the traditional interface.
For drive_del, that's easy: hmp_drive_del() sheds its unused last
parameter, and its return value, which the caller ignored anyway.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
|
|
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
|
|
Protocol must be spice, vnc isn't implemented. Fix up documentation.
Attempts to use vnc or any other unknown protocol yield the misleading
error message "Invalid parameter 'protocol'". Improve it to
"Parameter 'protocol' expects spice".
Cc: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by. Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Luiz Capitulino <lcapitulino@redhat.com>
|
|
Add the hmp interface to tune and query the parameters used in
live migration.
Signed-off-by: Liang Li <liang.z.li@intel.com>
Signed-off-by: Yang Zhang <yang.z.zhang@intel.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
|
|
Live migration with spice works like this today:
(1) client_migrate_info monitor cmd
(2) spice server notifies client, client connects to target host.
(3) qemu waits until spice client connect is finished.
(4) send over vmstate (i.e. main part of live migration).
(5) spice handover to target host.
(3) is implemented by making client_migrate_info a async monitor
command. This is the only async monitor command we have.
The original reason to implement this dance was that qemu did not accept
new tcp connections while the incoming migration was running, so (2) and
(4) could not be done in parallel. That issue was fixed long ago though.
Qemu version 1.3.0 (released Dec 2012) and newer happily accept tcp
connects while the incoming migration runs.
Time to drop step (3). This patch does exactly that, by making the
monitor command synchronous and removing the code needed to handle the
async monitor command in ui/spice-core.c
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Several issues:
* Commands i and o lack @item. Their one-liner documentation gets
squashed into the preceding command print. Add the obvious @item.
* Commands i, o and cpu-add lack @findex. The function index doesn't
have them. Add the obvious @findex.
* Commit 727f005 put block_set_io_throttle was added in the middle of
block_passwd. Move it.
* Correct spelling of commands chardev-add and chardev-remove in @item
and @findex.
* Some commands have a blank line between @item/@findex and the text,
most don't. Normalize to no blank line.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
The command handler is a union of two function types. If
cmd->user_print is set, handle_user_command() calls
cmd->mhandler.cmd_new(), else cmd->mhandler.cmd().
Command definitions must therefore either set both user_print() and
mhandler.cmd_new(), or only mhandler.cmd().
quit's sets user_print and mhandler.cmd(). handle_user_command()
calls hmp_quit() through mhandler.cmd_new() rather than
mhandler.cmd(), i.e. through a function pointer with a different type.
Broken in commit 7a7f325, v1.0.
Works in practice because hmp_quit() doesn't use its arguments, and
handle_user_command() ignores its function value.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
To complement qdev's bus-oriented info qtree, info qom-tree
prints a hierarchical view of the QOM composition tree.
By default, the machine composition tree is shown. This can be overriden
by supplying a path argument, such as "info qom-tree /".
Tested-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Re-implemented based on qmp_qom_set() to facilitate argument parsing.
Warn about ambiguous path arguments.
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Tested-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Implement it as a wrapper for QMP qom-list, but mimic the behavior of
scripts/qmp/qom-list in making the path argument optional and listing
the root if absent, to hint users what kind of path to pass.
Reviewed-by: Gonglei <arei.gonglei@huawei.com>
Tested-by: Alistair Francis <alistair.francis@xilinx.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
|
|
Add migrate_incoming/migrate-incoming to start an incoming
migration.
Once a qemu has been started with
-incoming defer
the migration can be started by issuing:
migrate_incoming uri
Signed-off-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Juan Quintela <quintela@redhat.com>
|
|
Commit 79ca616 (v1.6.0) accidentally disabled legacy x86-only HMP
commands pci_add, pci_del: it defined CONFIG_PCI_HOTPLUG only as make
variable, not as preprocessor macro, killing the code conditional on
defined(CONFIG_PCI_HOTPLUG_OLD).
In all this time, nobody reported the loss. I only noticed it when I
tried to test some error reporting change that forced me to touch this
old crap again.
Fun: git-log hw/pci/pci-hotplug-old.c shows our faith in the backward
compatibility god has been strong enough to sacrifice at its altar
about a dozen times, but not strong enough to even once verify the
legacy feature's still there, let alone works.
Remove the commands along with the code backing them.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Some are called do_COMMAND() (old ones, usually), some hmp_COMMAND(),
and sometimes COMMAND pointlessly differs in spelling.
Normalize to hmp_COMMAND(), where COMMAND is exactly the command name
with '-' replaced by '_'.
Exceptions:
* do_device_add() and client_migrate_info() *not* renamed to
hmp_device_add(), hmp_client_migrate_info(), because they're also
QMP handlers. They still need to be converted to QAPI.
* do_memory_dump(), do_physical_memory_dump(), do_ioport_read(),
do_ioport_write() renamed do hmp_* instead of hmp_x(), hmp_xp(),
hmp_i(), hmp_o(), because those names are too cryptic for my taste.
* do_info_help() renamed to hmp_info_help() instead of hmp_info(),
because it only covers help.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
|
|
This command lists PCMCIA sockets and cards. Only a few ARM boards
have sockets (akita, borzoi, connex, mainstone, spitz, terrier, tosa,
verdex, z2), the only card is the DSCM-1xxxx Hitachi Microdrive (qdev
"microdrive"), and it is only inserted during machine init, if ever.
So this command doesn't really tell anybody anything new so far.
Moreover, pcmcia_socket_unregister() has a use-after-free bug, flagged
by Coverity. Has never been used, because there has never been code
to eject a PCMCIA card.
Not worth fixing & converting to QMP. Remove it.
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Acked-by: Luiz Capitulino <lcapitulino@redhat.com>
Acked-by: Andreas Färber <afaerber@suse.de>
Message-id: 1411144812-22958-1-git-send-email-armbru@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
