| Age | Commit message (Collapse) | Author |
|---|
|
Introduce support for emulating the MIPS Boston development board. The
Boston board is built around an FPGA & 3 PCIe controllers, one of which
is connected to an Intel EG20T Platform Controller Hub. It is used
during the development & debug of new CPUs and the software intended to
run on them, and is essentially the successor to the older MIPS Malta
board.
This patch does not implement the EG20T, instead connecting an already
supported ICH-9 AHCI controller. Whilst this isn't accurate it's enough
for typical stock Boston software (eg. Linux kernels) to work with hard
disks given that both the ICH-9 & EG20T implement the AHCI
specification.
Boston boards typically boot kernels in the FIT image format, and this
patch will treat kernels provided to QEMU as such. When loading a kernel
directly, the board code will generate minimal firmware much as the
Malta board code does. This firmware will set up the CM, CPC & GIC
register base addresses then set argument registers & jump to the kernel
entry point. Alternatively, bootloader code may be loaded using the bios
argument in which case no firmware will be generated & execution will
proceed from the start of the boot code at the default MIPS boot
exception vector (offset 0x1fc00000 into (c)kseg1).
Currently real Boston boards are always used with FPGA bitfiles that
include a Global Interrupt Controller (GIC), so the interrupt
configuration is only defined for such cases. Therefore the board will
only allow use of CPUs which implement the CPS components, including the
GIC, and will otherwise exit with a message.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
[yongbok.kim@imgtec.com:
isolated boston machine support for mips64el.
updated for recent Chardev changes.
ignore missing bios/kernel for qtest.
added default -drive to if=ide explicitly.
changed default memory size into 1G due to make check failure
on 32-bit hosts]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
|
|
This reverts commit d3473e147a754e999718bf6fcb015d9978c6a1ee.
This commit creates a board which defaults to having 2GB of RAM.
Unfortunately on 32-bit hosts we can't create boards with 2GB of RAM,
and so 'make check' fails. I missed this during testing of the
merge, unfortunately. Luckily the offending commit is the last
one in the merge request, so we can just revert it for now.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Introduce support for emulating the MIPS Boston development board. The
Boston board is built around an FPGA & 3 PCIe controllers, one of which
is connected to an Intel EG20T Platform Controller Hub. It is used
during the development & debug of new CPUs and the software intended to
run on them, and is essentially the successor to the older MIPS Malta
board.
This patch does not implement the EG20T, instead connecting an already
supported ICH-9 AHCI controller. Whilst this isn't accurate it's enough
for typical stock Boston software (eg. Linux kernels) to work with hard
disks given that both the ICH-9 & EG20T implement the AHCI
specification.
Boston boards typically boot kernels in the FIT image format, and this
patch will treat kernels provided to QEMU as such. When loading a kernel
directly, the board code will generate minimal firmware much as the
Malta board code does. This firmware will set up the CM, CPC & GIC
register base addresses then set argument registers & jump to the kernel
entry point. Alternatively, bootloader code may be loaded using the bios
argument in which case no firmware will be generated & execution will
proceed from the start of the boot code at the default MIPS boot
exception vector (offset 0x1fc00000 into (c)kseg1).
Currently real Boston boards are always used with FPGA bitfiles that
include a Global Interrupt Controller (GIC), so the interrupt
configuration is only defined for such cases. Therefore the board will
only allow use of CPUs which implement the CPS components, including the
GIC, and will otherwise exit with a message.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Yongbok Kim <yongbok.kim@imgtec.com>
[yongbok.kim@imgtec.com:
isolated boston machine support for mips64el.
updated for recent Chardev changes.
ignore missing bios/kernel for qtest.
added default -drive to if=ide explicitly]
Signed-off-by: Yongbok Kim <yongbok.kim@imgtec.com>
|
|
This is in keeping with the toolchain and or1ksim.
Signed-off-by: Richard Henderson <rth@twiddle.net>
|
|
Both devices seem to be specific to the ARM platform. It's confusing
for the users if they show up on other target architectures, too
(e.g. when the user runs QEMU with "-device ?" to get a list of
supported devices). Thus let's introduce proper configuration switches
so that the devices are only compiled and included when they are
really required.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
Currently, the code to handle the legacy ISA bus is always included in
qemu. However there are lots of platforms that don't include ISA legacy
devies, and quite a few that have never used ISA legacy devices at all.
This patch allows the ISA bus code to be disabled in the configuration for
platforms where it doesn't make sense.
For now, the default configs are adjusted to include ISA on all platforms
including PCI: anything with PCI can at least in principle add an i82378
PCI->ISA bridge. Also, CONFIG_IDE_CORE which is already in pci.mak
requires ISA support.
We also explicitly enable ISA on some other non-PCI platforms which include
ISA devices: moxie, sparc and unicore32. We may want to pare this down in
future.
The platforms that will lose ISA by default are: cris, lm32, microblazeel,
microblaze, openrisc, s390x, tricore, xtensaeb, xtensa. As far as I can
tell none of these ever used ISA.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
|
|
At present, the core device model code for 8250-like serial ports
(serial.c) and the code for serial ports attached to ISA-style legacy IO
(serial-isa.c) are both controlled by the CONFIG_SERIAL variable.
There are lots and lots of embedded platforms that have 8250-like serial
ports but have never had anything resembling ISA legacy IO. Therefore,
split serial-isa into its own CONFIG_SERIAL_ISA option so it can be
disabled for platforms where it's not appropriate.
For now, I enabled CONFIG_SERIAL_ISA in every default-config where
CONFIG_SERIAL is enabled, excepting microblaze, or32, and xtensa. As best
as I can tell, those platforms never used legacy ISA, and also don't
include PCI support (which would allow connection of a PCI->ISA bridge
and/or a southbridge including legacy ISA serial ports).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
|
|
into staging
ppc patch queue 2017-02-02
This obsoletes ppc-for-2.9-20170112, which had a MacOS build bug.
This is a long overdue ppc pull request for qemu-2.9. It's been a
long time coming due to some holidays and inconveniently timed
problems with testing. So, there's a lot in here:
* More POWER9 instruction implementations for TCG
* The simpler parts of my CPU compatibility mode cleanup
* This changes behaviour to prefer compatibility modes over
"raW" mode for new machine type versions
* New "40p" machine type which is essentially a modernized and
cleaned up "prep". The intention is that it will replace "prep"
once it has some more testing and polish.
* Add pseries-2.9 machine type
* Implement H_SIGNAL_SYS_RESET hypercall
* Consolidate the two alternate CPU init paths in pseries by
making it always go through CPU core objects to initialize CPU
* A number of bugfixes and cleanups
* Stop the guest timebase when the guest is stopped under KVM.
This makes the guest system clock also stop when paused, which
matches the x86 behaviour.
* Some preliminary cleanups leading towards implementation of the
POWER9 MMU.
There are also some changes not strictly related to ppc code, but for
its benefit:
* Limit the pxi-expander-bridge (PXB) device to x86 guests only
(it's essentially a hack to work around historical x86
limitations)
* Some additions to the 128-bit math in host_utils, necessary for
some of the new instructions.
* Revise a number of qtests and enable them for ppc
# gpg: Signature made Thu 02 Feb 2017 01:40:16 GMT
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.9-20170202: (107 commits)
hw/ppc/pnv: Use error_report instead of hw_error if a ROM file can't be found
ppc/kvm: Handle the "family" CPU via alias instead of registering new types
target/ppc/mmu_hash64: Fix incorrect shift value in amr calculation
target/ppc/mmu_hash64: Fix printing unsigned as signed int
tcg/POWER9: NOOP the cp_abort instruction
target/ppc/debug: Print LPCR register value if register exists
target-ppc: Add xststdc[sp, dp, qp] instructions
target-ppc: Add xvtstdc[sp,dp] instructions
target-ppc: Add MMU model check for booke machines
ppc: switch to constants within BUILD_BUG_ON
target/ppc/cpu-models: Fix/remove bad CPU aliases
target/ppc: Remove unused POWERPC_FAMILY(POWER)
spapr: clock should count only if vm is running
ppc: Remove unused function cpu_ppc601_rtc_init()
target/ppc: Add pcr_supported to POWER9 cpu class definition
powerpc/cpu-models: rename ISAv3.00 logical PVR definition
target-ppc: Add xvcv[hpsp, sphp] instructions
target-ppc: Add xsmulqp instruction
target-ppc: Add xsdivqp instruction
target-ppc: Add xscvsdqp and xscvudqp instructions
...
# Conflicts:
# hw/pci-bridge/Makefile.objs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The 'base' PCI Express Root Port includes
the common code to be re-used for all
Root Ports implementations. Most of the code
was taken from the current implementation
of Intel's IOH 3420 Root Port.
Signed-off-by: Marcel Apfelbaum <marcel@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
The PCI Expander Bridge (PXB) device is essentially a hack to allow
different PCIe devices to be assigned to different NUMA nodes on x86. Each
PXB is sort-of a separate PCI host bridge, except that its config space
is shared with the config space of the main PCI host bridge, rather than
being independent.
This is only necessary if the platform doesn't (easily) allow truly
independent PCI host bridges. AFAIK that's just x86.
This patch makes it possible to configure PXB out of the build, and adjusts
the default configs so it's only included on x86 targets.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Machine supports both Open Hack'Ware and OpenBIOS.
Open Hack'Ware is the default because OpenBIOS is currently unable to boot
PReP boot partitions or PReP kernels.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
[dwg: Correct compile failure with KVM located by Thomas Huth]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
[dwg: Added CONFIG_RS6000_MC to ppc64 or it breaks testcases]
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Add remaining bits of the Altera NiosII R1 support into qemu, which
is documentation, MAINTAINERS file entry, configure bits, arch_init
and configuration files for both linux-user (userland binaries) and
softmmu (hardware emulation).
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chris Wulff <crwulff@gmail.com>
Cc: Jeff Da Silva <jdasilva@altera.com>
Cc: Ley Foon Tan <lftan@altera.com>
Cc: Sandra Loosemore <sandra@codesourcery.com>
Cc: Yves Vandervennet <yvanderv@altera.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Message-Id: <20170118220146.489-8-marex@denx.de>
Signed-off-by: Richard Henderson <rth@twiddle.net>
|
|
This is just about the minimum required to enable compilation
without actually executing any instructions. This contains the
HPPACPU structure and the required callbacks, the gdbstub, the
basic translation loop, and a translate_one function that always
results in an illegal instruction.
Signed-off-by: Richard Henderson <rth@twiddle.net>
|
|
Remove the Niagara stub implementation from sun4u.c and add a machine,
compatible with Legion simulator from the OpenSPARC T1 project.
The machine uses the firmware supplied with the OpenSPARC T1 project,
http://download.oracle.com/technetwork/systems/opensparc/OpenSPARCT1_Arch.1.5.tar.bz2
in the directory S10image/, and is able to boot the supplied Solaris 10 image.
Note that for compatibility with the naming conventions for SPARC machines
the new machine name is lowercase niagara.
Signed-off-by: Artyom Tarasenko <atar4qemu@gmail.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
|
|
None of the ColdFire boards that we currently support has a PCI or
USB bus (and AFAIK the upcoming q800 machine does not support PCI
and USB either), so we do not need these settings the config file.
Signed-off-by: Thomas Huth <huth@tuxfamily.org>
Message-Id: <20170106083956.53d08923@thl530>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
|
|
as they use completely different way to handle hotplug event
Suggested-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
|
|
The goal is to emulate a PowerNV system at the level of the skiboot
firmware, which loads the OS and provides some runtime services. Power
Systems have a lower firmware (HostBoot) that does low level system
initialization, like DRAM training. This is beyond the scope of what
qemu will address in a PowerNV guest.
No devices yet, not even an interrupt controller. Just to get started,
some RAM to load the skiboot firmware, the kernel and initrd. The
device tree is fully created in the machine reset op.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[clg: - updated for qemu-2.7
- replaced fprintf by error_report
- used a common definition of _FDT macro
- removed VMStateDescription as migration is not yet supported
- added IBM Copyright statements
- reworked kernel_filename handling
- merged PnvSystem and sPowerNVMachineState
- removed PHANDLE_XICP
- added ppc_create_page_sizes_prop helper
- removed nmi support
- removed kvm support
- updated powernv machine to version 2.8
- removed chips and cpus, They will be provided in another patches
- added a machine reset routine to initialize the device tree (also)
- french has a squelette and english a skeleton.
- improved commit log.
- reworked prototypes parameters
- added a check on the ram size (thanks to Michael Ellerman)
- fixed chip-id cell
- changed MAX_CPUS to 2048
- simplified memory node creation to one node only
- removed machine version
- rewrote the device tree creation with the fdt "rw" routines
- s/sPowerNVMachineState/PnvMachineState/
- etc.]
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
In order to cleanup linux-user, we need support for most relatively
modern syscalls. unicore32 lacks support for syscalls like
epoll_pwait, preventing cleaning up the CONFIG_EPOLL mess.
This patch can be reverted when unicore32 starts either supporting
the syscalls as defined in mainline kernel, or the oldabi interface
gains support for syscalls supported since at kernel 2.6.19 / glibc 2.6
Cc: MPRC <zhangheng@mprc.pku.edu.cn>
Cc: Xuetao Guan <gxt@mprc.pku.edu.cn>
Signed-off-by: Riku Voipio <riku.voipio@linaro.org>
|
|
Add the STM32F2xx SPI device.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 8197811d5c94f814fa67c6a33ca2f7fd0aa97432.1474742262.git.alistair@alistair23.me
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add the STM32F2xx ADC device. This device randomly
generates values on each read.
This also includes creating a hw/adc directory.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 3240e660adaf537f55a63ce06096e844aece8cda.1474742262.git.alistair@alistair23.me
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The CONFIG_PIIX_PCI=y setting was added in
commit 70615c38ded2a20ad8282b7dcde95482fc0a7744
Author: Blue Swirl <blauwirbel@gmail.com>
Date: Mon Mar 22 20:18:40 2010 +0000
Compile sound devices only once
but nothing in that commit, nor anything pre-existing,
ever referenced CONFIG_PIIX_PCI.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1473096320-1638-4-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The use of the CONFIG_ISA_MMIO setting was removed in
commit 61fcb628627ea464dc1954f615ae13edfefd284f
Author: Paolo Bonzini <pbonzini@redhat.com>
Date: Mon Jul 22 15:54:24 2013 +0200
isa_mmio: delete
but this commit only removed it from some of the default
config files.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1473096320-1638-3-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The CONFIG_PAM=y setting was added in
commit c0907c9e6417cb959dfd9ef6873221536ec91351
Author: Paolo Bonzini <pbonzini@redhat.com>
Date: Tue Feb 5 15:06:20 2013 +0100
hw: move PCI bridges to hw/pci-* or hw/ARCH
but nothing in that commit, nor anything pre-existing,
ever referenced CONFIG_PAM.
Signed-off-by: Daniel P. Berrange <berrange@redhat.com>
Message-Id: <1473096320-1638-2-git-send-email-berrange@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Add a minimal model for the devcfg device which is part of Zynq.
This model supports DMA capabilities and interrupt generation.
Signed-off-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com>
Signed-off-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 83df49d8fa2d203a421ca71620809e4b04754e65.1467053537.git.alistair.francis@xilinx.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Leave the core ICP/ICS logic in xics.c and move the top level
class wrapper, hypercall and RTAS handlers to xics_spapr.c
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[add cpu.h in xics_spapr.c, move set_nr_irqs and set_nr_servers to
xics_spapr.c]
Signed-off-by: Nikunj A Dadhania <nikunj@linux.vnet.ibm.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Implement an I2C slave which implements DDC and returns the
EDID data for an attached monitor.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Tested-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Message-id: 1465833014-21982-7-git-send-email-fred.konrad@greensocs.com
- Rebased on the current master.
- Modified for QOM.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Tested-By: Hyun Kwon <hyun.kwon@xilinx.com>
[PMM: actually wire up the vmstate to dc->vmsd]
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
This introduces dpcd module.
It wires on a aux-bus and can be accessed by the driver to get lane-speed, etc.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Tested-By: Hyun Kwon <hyun.kwon@xilinx.com>
Message-id: 1465833014-21982-6-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
This introduces a new bus: aux-bus.
It contains an address space for aux slaves devices and a bridge to an I2C bus
for I2C through AUX transactions.
Signed-off-by: KONRAD Frederic <fred.konrad@greensocs.com>
Tested-By: Hyun Kwon <hyun.kwon@xilinx.com>
Reviewed-by: Alistair Francis <alistair.francis@xilinx.com>
Message-id: 1465833014-21982-5-git-send-email-fred.konrad@greensocs.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
This patch introduces emulation for the Intel 82574 adapter, AKA e1000e.
This implementation is derived from the e1000 emulation code, and
utilizes the TX/RX packet abstractions that were initially developed for
the vmxnet3 device. Although some parts of the introduced code may be
shared with e1000, the differences are substantial enough so that the
only shared resources for the two devices are the definitions in
hw/net/e1000_regs.h.
Similarly to vmxnet3, the new device uses virtio headers for task
offloads (for backends that support virtio extensions). Usage of
virtio headers may be forcibly disabled via a boolean device property
"vnet" (which is enabled by default). In such case task offloads
will be performed in software, in the same way it is done on
backends that do not support virtio headers.
The device code is split into two parts:
1. hw/net/e1000e.c: QEMU-specific code for a network device;
2. hw/net/e1000e_core.[hc]: Device emulation according to the spec.
The new device name is e1000e.
Intel specifications for the 82574 controller are available at:
http://www.intel.com/content/dam/doc/datasheet/82574l-gbe-controller-datasheet.pdf
Throughput measurement results (iperf2):
Fedora 22 guest, TCP, RX
4 ++------------------------------------------+
| |
| X X X X X
3.5 ++ X X X X |
| X |
| |
3 ++ |
G | X |
b | |
/ 2.5 ++ |
s | |
| |
2 ++ |
| |
| |
1.5 X+ |
| |
+ + + + + + + + + + + +
1 ++--+---+---+---+---+---+---+---+---+---+---+
32 64 128 256 512 1 2 4 8 16 32 64
B B B B B KB KB KB KB KB KB KB
Buffer size
Fedora 22 guest, TCP, TX
18 ++-------------------------------------------+
| X |
16 ++ X X X X X
| X |
14 ++ |
| |
12 ++ |
G | X |
b 10 ++ |
/ | |
s 8 ++ |
| |
6 ++ X |
| |
4 ++ |
| X |
2 ++ X |
X + + + + + + + + + + +
0 ++--+---+---+---+---+----+---+---+---+---+---+
32 64 128 256 512 1 2 4 8 16 32 64
B B B B B KB KB KB KB KB KB KB
Buffer size
Fedora 22 guest, UDP, RX
3 ++------------------------------------------+
| X
| |
2.5 ++ |
| |
| |
2 ++ X |
G | |
b | |
/ 1.5 ++ |
s | X |
| |
1 ++ |
| |
| X |
0.5 ++ |
| X |
X + + + + +
0 ++-------+--------+-------+--------+--------+
32 64 128 256 512 1
B B B B B KB
Datagram size
Fedora 22 guest, UDP, TX
1 ++------------------------------------------+
| X
0.9 ++ |
| |
0.8 ++ |
0.7 ++ |
| |
G 0.6 ++ |
b | |
/ 0.5 ++ |
s | X |
0.4 ++ |
| |
0.3 ++ |
0.2 ++ X |
| |
0.1 ++ X |
X X + + + +
0 ++-------+--------+-------+--------+--------+
32 64 128 256 512 1
B B B B B KB
Datagram size
Windows 2012R2 guest, TCP, RX
3.2 ++------------------------------------------+
| X |
3 ++ |
| |
2.8 ++ |
| |
2.6 ++ X |
G | X X X X X
b 2.4 ++ X X |
/ | |
s 2.2 ++ |
| |
2 ++ |
| X X |
1.8 ++ |
| |
1.6 X+ |
+ + + + + + + + + + + +
1.4 ++--+---+---+---+---+---+---+---+---+---+---+
32 64 128 256 512 1 2 4 8 16 32 64
B B B B B KB KB KB KB KB KB KB
Buffer size
Windows 2012R2 guest, TCP, TX
14 ++-------------------------------------------+
| |
| X X
12 ++ |
| |
10 ++ |
| |
G | |
b 8 ++ |
/ | X |
s 6 ++ |
| |
| |
4 ++ X |
| |
2 ++ |
| X X X |
+ X X + + X X + + + + +
0 X+--+---+---+---+---+----+---+---+---+---+---+
32 64 128 256 512 1 2 4 8 16 32 64
B B B B B KB KB KB KB KB KB KB
Buffer size
Windows 2012R2 guest, UDP, RX
1.6 ++------------------------------------------X
| |
1.4 ++ |
| |
1.2 ++ |
| X |
| |
G 1 ++ |
b | |
/ 0.8 ++ |
s | |
0.6 ++ X |
| |
0.4 ++ |
| X |
| |
0.2 ++ X |
X + + + + +
0 ++-------+--------+-------+--------+--------+
32 64 128 256 512 1
B B B B B KB
Datagram size
Windows 2012R2 guest, UDP, TX
0.6 ++------------------------------------------+
| X
| |
0.5 ++ |
| |
| |
0.4 ++ |
G | |
b | |
/ 0.3 ++ X |
s | |
| |
0.2 ++ |
| |
| X |
0.1 ++ |
| X |
X X + + + +
0 ++-------+--------+-------+--------+--------+
32 64 128 256 512 1
B B B B B KB
Datagram size
Signed-off-by: Dmitry Fleytman <dmitry.fleytman@ravellosystems.com>
Signed-off-by: Leonid Bloch <leonid.bloch@ravellosystems.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
For now we only support the following devices:
* up to 4 Cortex A9 cores
* A9 MPCORE (SCU, GIC, TWD)
* 5 i.MX UARTs
* 2 EPIT timers
* 1 GPT timer
* 3 I2C controllers
* 7 GPIO controllers
* 6 SDHC controllers
* 5 SPI controllers
* 1 CCM device
* 1 SRC device
* various ROM/RAM areas.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Jean-Christophe Dubois <jcd@tribudubois.net>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
This will be used by ARM virt machine as a power button.
Signed-off-by: Shannon Zhao <shannon.zhao@linaro.org>
Message-id: 1458221140-15232-2-git-send-email-zhaoshenglong@huawei.com
[PMM: Use hyphen rather than underscore in type names;
add a comment briefly describing what the device does]
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Implement ITC as a single object consisting of two memory regions:
1) tag_io: ITC Configuration Tags (i.e. ITCAddressMap{0,1} registers) which
are accessible by the CPU via CACHE instruction. Also adding
MemoryRegion *itc_tag to the CPUMIPSState so that CACHE instruction will
dispatch reads/writes directly.
2) storage_io: memory-mapped ITC Storage whose address space is configurable
(i.e. enabled/remapped/resized) by writing to ITCAddressMap{0,1} registers.
ITC Storage contains FIFO and Semaphore cells. Read-only FIFO bit in the
ITC cell tag indicates the type of the cell. If the ITC Storage contains
both types of cells then FIFOs are located before Semaphores.
Since issuing thread can get blocked on the access to a cell (in E/F
Synchronized and P/V Synchronized Views) each cell has a bitmap to track
which threads are currently blocked.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Implement generic MIPS Coherent Processing System (CPS) which in this
commit just creates VPs, but it will serve as a container also for
other components like Global Configuration Registers and Cluster Power
Controller.
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
MIPS patches 2016-03-23
Changes:
* add mips-softmmu-common.mak
* indicate presence of IEEE 754-2008 FPU in MIPS64R6-generic and P5600
# gpg: Signature made Wed 23 Mar 2016 16:38:04 GMT using RSA key ID 0B29DA6B
# gpg: Good signature from "Leon Alrae <leon.alrae@imgtec.com>"
* remotes/lalrae/tags/mips-20160323:
default-configs: add mips-softmmu-common.mak
target-mips: indicate presence of IEEE 754-2008 FPU in R6/R5+MSA CPUs
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add mips-softmmu-common.mak and include it in existing mips*-softmmu.mak
files to avoid having to repeat CONFIG defines four times.
Suggested-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Event notifiers are designed for eventfd(2). They can fall back to
pipes, but according to Paolo, event_notifier_init_fd() really
requires the real thing, and should therefore be under #ifdef
CONFIG_EVENTFD. Do that.
Its only user is ivshmem, which is currently CONFIG_POSIX. Narrow it
to CONFIG_EVENTFD.
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1458066895-20632-6-git-send-email-armbru@redhat.com>
|
|
Implement basic ASPEED timer functionality for the AST2400 SoC[1]: Up to
8 timers can independently be configured, enabled, reset and disabled.
Some hardware features are not implemented, namely clock value matching
and pulse generation, but the implementation is enough to boot the Linux
kernel configured with aspeed_defconfig.
[1] http://www.aspeedtech.com/products.php?fPath=20&rId=376
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Message-id: 1458096317-25223-2-git-send-email-andrew@aj.id.au
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
This adds the SAS1068 device, a SAS disk controller used in VMware that
is oldish but widely supported and has decent performance. Unlike
megasas, it presents itself as a SAS controller and not as a RAID
controller. The device corresponds to the mptsas kernel driver in
Linux.
A few small things in the device setup are based on Don Slutz's old
patch, but the device emulation was written from scratch based on Don's
SeaBIOS patch and on the FreeBSD and Linux drivers. It is 2400 lines
shorter than Don's patch (and roughly the same size as MegaSAS---also
because it doesn't support the similar SPI controller), implements SCSI
task management functions (with asynchronous cancellation), supports
big-endian hosts, has complete support for migration and follows the
QEMU coding standards much more closely.
To write the driver, I first split Don's patch in two parts, with
the configuration bits in one file and the rest in a separate file.
I first left mptconfig.c in place and rewrote the rest, then deleted
mptconfig.c as well. The configuration pages are still based mostly on
VirtualBox's, though not exactly the same. However, the implementation
is completely different. The contents of the pages themselves should
not be copyrightable.
Signed-off-by: Don Slutz <Don@CloudSwitch.com>
Message-Id: <1347382813-5662-1-git-send-email-Don@CloudSwitch.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This adds the system mailboxes which are used to communicate with a
number of GPU peripherals on Pi/Pi2.
Reviewed-by: Peter Crosthwaite <crosthwaite.peter@gmail.com>
Signed-off-by: Andrew Baumann <Andrew.Baumann@microsoft.com>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
NFIT is defined in ACPI 6.0: 5.2.25 NVDIMM Firmware Interface Table (NFIT)
Currently, we only support PMEM mode. Each device has 3 structures:
- SPA structure, defines the PMEM region info
- MEM DEV structure, it has the @handle which is used to associate specified
ACPI NVDIMM device we will introduce in later patch.
Also we can happily ignored the memory device's interleave, the real
nvdimm hardware access is hidden behind host
- DCR structure, it defines vendor ID used to associate specified vendor
nvdimm driver. Since we only implement PMEM mode this time, Command
window and Data window are not needed
The NVDIMM functionality is controlled by the parameter, 'nvdimm', which
is introduced for the machine, there is a example to enable it:
-machine pc,nvdimm -m 8G,maxmem=100G,slots=100 -object \
memory-backend-file,id=mem1,share,mem-path=/tmp/nvdimm1,size=10G -device \
nvdimm,memdev=mem1,id=nv1
It is disabled on default
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Introduce "nvdimm" device which is based on pc-dimm device type
Currently, nothing is specific for nvdimm but hotplug is disabled
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Xiao Guangrong <guangrong.xiao@linux.intel.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This provides the simulation of the BT hardware interface for
IPMI.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This provides the simulation of the KCS hardware interface.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This adds an interface for IPMI that connects to a remote
BMC over a chardev (generally a TCP socket). The OpenIPMI
lanserv simulator describes this interface, see that for
interface details.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This provides a minimal local BMC, basically enough to comply with the
spec and provide a complete watchdog timer (including a sensor, SDR,
and event).
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Add the basic IPMI types and infrastructure to QEMU. Low-level
interfaces and simulation interfaces will register with this; it's
kind of the go-between to tie them together.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
'hyperv-testdev' will be used by kvm-unit-tests
to setup Hyper-V SynIC SINT's routing and to inject
Hyper-V SynIC SINT's.
Hyper-V test device is ISA type device that creates 0x3000
IO memory region and catches write access into it. Every
write operation data decoded into ctl code and parameters
for Hyper-V test device.
Signed-off-by: Andrey Smetanin <asmetanin@virtuozzo.com>
Reviewed-by: Roman Kagan <rkagan@virtuozzo.com>
Signed-off-by: Denis V. Lunev <den@openvz.org>
CC: Paolo Bonzini <pbonzini@redhat.com>
CC: Richard Henderson <rth@twiddle.net>
CC: Eduardo Habkost <ehabkost@redhat.com>
CC: "Andreas Färber" <afaerber@suse.de>
CC: Marcelo Tosatti <mtosatti@redhat.com>
CC: Roman Kagan <rkagan@virtuozzo.com>
CC: Denis V. Lunev <den@openvz.org>
CC: kvm@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The uses of the CONFIG_GDBSTUB_XML define were removed in commit
b77abd95a9484c, but the define in aarch64-linux-user.mak somehow
escaped the cull (the patchset probably crossed in the mail with
the patches adding aarch64 support). Remove the stray define.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Laurent Desnogues <laurent.desnogues@gmail.com>
Message-id: 1447690178-4560-1-git-send-email-peter.maydell@linaro.org
|
|
ivshmem doesn't actually require kvm, so enable it when POSIX is
enabled. (it is required however when ioeventfd is enabled)
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
|
