aboutsummaryrefslogtreecommitdiff
path: root/block/parallels.c
AgeCommit message (Collapse)Author
2020-07-10error: Avoid error_propagate() after migrate_add_blocker()Markus Armbruster
When migrate_add_blocker(blocker, &errp) is followed by error_propagate(errp, err), we can often just as well do migrate_add_blocker(..., errp). Do that with this Coccinelle script: @@ expression blocker, err, errp; expression ret; @@ - ret = migrate_add_blocker(blocker, &err); - if (err) { + ret = migrate_add_blocker(blocker, errp); + if (ret < 0) { ... when != err; - error_propagate(errp, err); ... } @@ expression blocker, err, errp; @@ - migrate_add_blocker(blocker, &err); - if (err) { + if (migrate_add_blocker(blocker, errp) < 0) { ... when != err; - error_propagate(errp, err); ... } Double-check @err is not used afterwards. Dereferencing it would be use after free, but checking whether it's null would be legitimate. Signed-off-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Message-Id: <20200707160613.848843-43-armbru@redhat.com>
2020-07-10qapi: Smooth another visitor error checking patternMarkus Armbruster
Convert visit_type_FOO(v, ..., &ptr, &err); ... if (err) { ... } to visit_type_FOO(v, ..., &ptr, errp); ... if (!ptr) { ... } for functions that set @ptr to non-null / null on success / error. Eliminate error_propagate() that are now unnecessary. Delete @err that are now unused. Signed-off-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Message-Id: <20200707160613.848843-40-armbru@redhat.com>
2020-07-10block/parallels: Simplify parallels_open() after previous commitMarkus Armbruster
Signed-off-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Message-Id: <20200707160613.848843-39-armbru@redhat.com>
2020-07-10error: Reduce unnecessary error propagationMarkus Armbruster
When all we do with an Error we receive into a local variable is propagating to somewhere else, we can just as well receive it there right away, even when we need to keep error_propagate() for other error paths. Signed-off-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Message-Id: <20200707160613.848843-38-armbru@redhat.com>
2020-07-10error: Eliminate error_propagate() with Coccinelle, part 1Markus Armbruster
When all we do with an Error we receive into a local variable is propagating to somewhere else, we can just as well receive it there right away. Convert if (!foo(..., &err)) { ... error_propagate(errp, err); ... return ... } to if (!foo(..., errp)) { ... ... return ... } where nothing else needs @err. Coccinelle script: @rule1 forall@ identifier fun, err, errp, lbl; expression list args, args2; binary operator op; constant c1, c2; symbol false; @@ if ( ( - fun(args, &err, args2) + fun(args, errp, args2) | - !fun(args, &err, args2) + !fun(args, errp, args2) | - fun(args, &err, args2) op c1 + fun(args, errp, args2) op c1 ) ) { ... when != err when != lbl: when strict - error_propagate(errp, err); ... when != err ( return; | return c2; | return false; ) } @rule2 forall@ identifier fun, err, errp, lbl; expression list args, args2; expression var; binary operator op; constant c1, c2; symbol false; @@ - var = fun(args, &err, args2); + var = fun(args, errp, args2); ... when != err if ( ( var | !var | var op c1 ) ) { ... when != err when != lbl: when strict - error_propagate(errp, err); ... when != err ( return; | return c2; | return false; | return var; ) } @depends on rule1 || rule2@ identifier err; @@ - Error *err = NULL; ... when != err Not exactly elegant, I'm afraid. The "when != lbl:" is necessary to avoid transforming if (fun(args, &err)) { goto out } ... out: error_propagate(errp, err); even though other paths to label out still need the error_propagate(). For an actual example, see sclp_realize(). Without the "when strict", Coccinelle transforms vfio_msix_setup(), incorrectly. I don't know what exactly "when strict" does, only that it helps here. The match of return is narrower than what I want, but I can't figure out how to express "return where the operand doesn't use @err". For an example where it's too narrow, see vfio_intx_enable(). Silently fails to convert hw/arm/armsse.c, because Coccinelle gets confused by ARMSSE being used both as typedef and function-like macro there. Converted manually. Line breaks tidied up manually. One nested declaration of @local_err deleted manually. Preexisting unwanted blank line dropped in hw/riscv/sifive_e.c. Signed-off-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Message-Id: <20200707160613.848843-35-armbru@redhat.com>
2020-07-10qemu-option: Use returned bool to check for failureMarkus Armbruster
The previous commit enables conversion of foo(..., &err); if (err) { ... } to if (!foo(..., &err)) { ... } for QemuOpts functions that now return true / false on success / error. Coccinelle script: @@ identifier fun = { opts_do_parse, parse_option_bool, parse_option_number, parse_option_size, qemu_opt_parse, qemu_opt_rename, qemu_opt_set, qemu_opt_set_bool, qemu_opt_set_number, qemu_opts_absorb_qdict, qemu_opts_do_parse, qemu_opts_from_qdict_entry, qemu_opts_set, qemu_opts_validate }; expression list args, args2; typedef Error; Error *err; @@ - fun(args, &err, args2); - if (err) + if (!fun(args, &err, args2)) { ... } A few line breaks tidied up manually. Signed-off-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Message-Id: <20200707160613.848843-15-armbru@redhat.com> [Conflict with commit 0b6786a9c1 "block/amend: refactor qcow2 amend options" resolved by rerunning Coccinelle on master's version]
2020-07-10qemu-option: Check return value instead of @err where convenientMarkus Armbruster
Convert uses like opts = qemu_opts_create(..., &err); if (err) { ... } to opts = qemu_opts_create(..., errp); if (!opts) { ... } Eliminate error_propagate() that are now unnecessary. Delete @err that are now unused. Note that we can't drop parallels_open()'s error_propagate() here. We continue to execute it even in the converted case. It's a no-op then: local_err is null. Signed-off-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Reviewed-by: Greg Kurz <groug@kaod.org> Message-Id: <20200707160613.848843-8-armbru@redhat.com>
2020-05-18block: Use bdrv_default_perms()Max Reitz
bdrv_default_perms() can decide which permission profile to use based on the BdrvChildRole, so block drivers do not need to select it explicitly. The blkverify driver now no longer shares the WRITE permission for the image to verify. We thus have to adjust two places in test-block-iothread not to take it. (Note that in theory, blkverify should behave like quorum in this regard and share neither WRITE nor RESIZE for both of its children. In practice, it does not really matter, because blkverify is used only for debugging, so we might as well keep its permissions rather liberal.) Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Message-Id: <20200513110544.176672-30-mreitz@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2020-05-18block: Make format drivers use child_of_bdsMax Reitz
Commonly, they need to pass the BDRV_CHILD_IMAGE set as the BdrvChildRole; but there are exceptions for drivers with external data files (qcow2 and vmdk). Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Message-Id: <20200513110544.176672-26-mreitz@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2020-05-18block: Add BdrvChildRole to BdrvChildMax Reitz
For now, it is always set to 0. Later patches in this series will ensure that all callers pass an appropriate combination of flags. Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Message-Id: <20200513110544.176672-6-mreitz@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2020-05-18block: Add BlockDriver.is_formatMax Reitz
We want to unify child_format and child_file at some point. One of the important things that set format drivers apart from other drivers is that they do not expect other format nodes under them (except in the backing chain), i.e. we must not probe formats inside of formats. That means we need something on which to distinguish format drivers from others, and hence this flag. Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Reviewed-by: Alberto Garcia <berto@igalia.com> Message-Id: <20200513110544.176672-3-mreitz@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2020-05-08parallels: Rework truncation logicEric Blake
The parallels driver tries to use truncation for image growth, but can only do so when reads are guaranteed as zero. Now that we have a way to request zero contents from truncation, we can defer the decision to actual allocation attempts rather than up front, reducing the number of places that still use bdrv_has_zero_init_truncate. Signed-off-by: Eric Blake <eblake@redhat.com> Message-Id: <20200428202905.770727-8-eblake@redhat.com> Reviewed-by: Denis V. Lunev <den@openvz.org> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2020-05-05block: Add blk_new_with_bs() helperEric Blake
There are several callers that need to create a new block backend from an existing BDS; make the task slightly easier with a common helper routine. Suggested-by: Max Reitz <mreitz@redhat.com> Signed-off-by: Eric Blake <eblake@redhat.com> Message-Id: <20200424190903.522087-2-eblake@redhat.com> [mreitz: Set @ret only in error paths, see https://lists.nongnu.org/archive/html/qemu-block/2020-04/msg01216.html] Signed-off-by: Max Reitz <mreitz@redhat.com> Message-Id: <20200428192648.749066-2-eblake@redhat.com> Signed-off-by: Max Reitz <mreitz@redhat.com>
2020-04-30block: Add flags to bdrv(_co)_truncate()Kevin Wolf
Now that block drivers can support flags for .bdrv_co_truncate, expose the parameter in the node level interfaces bdrv_co_truncate() and bdrv_truncate(). Signed-off-by: Kevin Wolf <kwolf@redhat.com> Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Reviewed-by: Alberto Garcia <berto@igalia.com> Reviewed-by: Max Reitz <mreitz@redhat.com> Message-Id: <20200424125448.63318-3-kwolf@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2020-03-26block: pass BlockDriver reference to the .bdrv_co_createMaxim Levitsky
This will allow the reuse of a single generic .bdrv_co_create implementation for several drivers. No functional changes. Signed-off-by: Maxim Levitsky <mlevitsk@redhat.com> Message-Id: <20200326011218.29230-2-mlevitsk@redhat.com> Reviewed-by: Denis V. Lunev <den@openvz.org> Signed-off-by: Max Reitz <mreitz@redhat.com>
2019-10-28Merge remote-tracking branch 'remotes/maxreitz/tags/pull-block-2019-10-28' ↵Peter Maydell
into staging Block patches for softfreeze: - iotest patches - Improve performance of the mirror block job in write-blocking mode - Limit memory usage for the backup block job - Add discard and write-zeroes support to the NVMe host block driver - Fix a bug in the mirror job - Prevent the qcow2 driver from creating technically non-compliant qcow2 v3 images (where there is not enough extra data for snapshot table entries) - Allow callers of bdrv_truncate() (etc.) to determine whether the file must be resized to the exact given size or whether it is OK for block devices not to shrink # gpg: Signature made Mon 28 Oct 2019 12:13:53 GMT # gpg: using RSA key 91BEB60A30DB3E8857D11829F407DB0061D5CF40 # gpg: issuer "mreitz@redhat.com" # gpg: Good signature from "Max Reitz <mreitz@redhat.com>" [full] # Primary key fingerprint: 91BE B60A 30DB 3E88 57D1 1829 F407 DB00 61D5 CF40 * remotes/maxreitz/tags/pull-block-2019-10-28: (69 commits) qemu-iotests: restrict 264 to qcow2 only Revert "qemu-img: Check post-truncation size" block: Pass truncate exact=true where reasonable block: Let format drivers pass @exact block: Evaluate @exact in protocol drivers block: Add @exact parameter to bdrv_co_truncate() block: Do not truncate file node when formatting block/cor: Drop cor_co_truncate() block: Handle filter truncation like native impl. iotests: Test qcow2's snapshot table handling iotests: Add peek_file* functions qcow2: Fix v3 snapshot table entry compliancy qcow2: Repair snapshot table with too many entries qcow2: Fix overly long snapshot tables qcow2: Keep track of the snapshot table length qcow2: Fix broken snapshot table entries qcow2: Add qcow2_check_fix_snapshot_table() qcow2: Separate qcow2_check_read_snapshot_table() qcow2: Write v3-compliant snapshot list on upgrade qcow2: Put qcow2_upgrade() into its own function ... Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2019-10-28block: Pass truncate exact=true where reasonableMax Reitz
This is a change in behavior, so all instances need a good justification. The comments added here should explain my reasoning. qed already had a comment that suggests it always expected bdrv_truncate()/blk_truncate() to behave as if exact=true were passed (c743849bee7 came eight months before 55b949c8476), so it was simply broken until now. Signed-off-by: Max Reitz <mreitz@redhat.com> Message-id: 20190918095144.955-8-mreitz@redhat.com Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com> [mreitz: Changed comment in qed.c to explain why a new QED file must be empty, as requested and suggested by Maxim] Signed-off-by: Max Reitz <mreitz@redhat.com>
2019-10-28block: Add @exact parameter to bdrv_co_truncate()Max Reitz
We have two drivers (iscsi and file-posix) that (in some cases) return success from their .bdrv_co_truncate() implementation if the block device is larger than the requested offset, but cannot be shrunk. Some callers do not want that behavior, so this patch adds a new parameter that they can use to turn off that behavior. This patch just adds the parameter and lets the block/io.c and block/block-backend.c functions pass it around. All other callers always pass false and none of the implementations evaluate it, so that this patch does not change existing behavior. Future patches take care of that. Suggested-by: Maxim Levitsky <mlevitsk@redhat.com> Signed-off-by: Max Reitz <mreitz@redhat.com> Message-id: 20190918095144.955-5-mreitz@redhat.com Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com> Signed-off-by: Max Reitz <mreitz@redhat.com>
2019-10-28block: Do not truncate file node when formattingMax Reitz
There is no reason why the format drivers need to truncate the protocol node when formatting it. When using the old .bdrv_co_create_ops() interface, the file will be created with no size option anyway, which generally gives it a size of 0. (Exceptions are block devices, which cannot be truncated anyway.) When using blockdev-create, the user must have given the file node some size anyway, so there is no reason why we should override that. qed is an exception, it needs the file to start completely empty (as explained by c743849bee7333c7ef256b7e12e34ed6f907064f). Signed-off-by: Max Reitz <mreitz@redhat.com> Message-id: 20190918095144.955-4-mreitz@redhat.com Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com> Signed-off-by: Max Reitz <mreitz@redhat.com>
2019-10-26core: replace getpagesize() with qemu_real_host_page_sizeWei Yang
There are three page size in qemu: real host page size host page size target page size All of them have dedicate variable to represent. For the last two, we use the same form in the whole qemu project, while for the first one we use two forms: qemu_real_host_page_size and getpagesize(). qemu_real_host_page_size is defined to be a replacement of getpagesize(), so let it serve the role. [Note] Not fully tested for some arch or device. Signed-off-by: Wei Yang <richardw.yang@linux.intel.com> Message-Id: <20191013021145.16011-3-richardw.yang@linux.intel.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2019-08-19block: Use bdrv_has_zero_init_truncate()Max Reitz
vhdx and parallels call bdrv_has_zero_init() when they do not really care about an image's post-create state but only about what happens when you grow an image. That is a bit ugly, and also overly safe when growing preallocated images without preallocating the new areas. Let them use bdrv_has_zero_init_truncate() instead. Signed-off-by: Max Reitz <mreitz@redhat.com> Message-id: 20190724171239.8764-6-mreitz@redhat.com Reviewed-by: Maxim Levitsky <mlevitsk@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> [mreitz: Added commit message] Signed-off-by: Max Reitz <mreitz@redhat.com>
2019-06-04block: Add BlockBackend.ctxKevin Wolf
This adds a new parameter to blk_new() which requires its callers to declare from which AioContext this BlockBackend is going to be used (or the locks of which AioContext need to be taken anyway). The given context is only stored and kept up to date when changing AioContexts. Actually applying the stored AioContext to the root node is saved for another commit. Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2019-04-30block/parallels: use buffer-based ioVladimir Sementsov-Ogievskiy
Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2019-02-22block/parallels: use QEMU_IOVEC_INIT_BUFVladimir Sementsov-Ogievskiy
Use new QEMU_IOVEC_INIT_BUF() instead of qemu_iovec_init_external( ... , 1), which simplifies the code. Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Reviewed-by: Eric Blake <eblake@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Message-id: 20190218140926.333779-8-vsementsov@virtuozzo.com Message-Id: <20190218140926.333779-8-vsementsov@virtuozzo.com> Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2018-06-29parallels: Switch to byte-based callsEric Blake
We are gradually moving away from sector-based interfaces, towards byte-based. Make the change for the last few sector-based calls into the block layer from the parallels driver. Ideally, the parallels driver should switch to doing everything byte-based, but that's a more invasive change that requires a bit more auditing. Signed-off-by: Eric Blake <eblake@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Reviewed-by: Denis V. Lunev <den@openvz.org> Reviewed-by: Jeff Cody <jcody@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2018-06-15block: Factor out qobject_input_visitor_new_flat_confused()Markus Armbruster
Signed-off-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Kevin Wolf <kwolf@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2018-06-15block: Clean up a misuse of qobject_to() in .bdrv_co_create_opts()Markus Armbruster
The following pattern occurs in the .bdrv_co_create_opts() methods of parallels, qcow, qcow2, qed, vhdx and vpc: qobj = qdict_crumple_for_keyval_qiv(qdict, errp); qobject_unref(qdict); qdict = qobject_to(QDict, qobj); if (qdict == NULL) { ret = -EINVAL; goto done; } v = qobject_input_visitor_new_keyval(QOBJECT(qdict)); [...] ret = 0; done: qobject_unref(qdict); [...] return ret; If qobject_to() fails, we return failure without setting errp. That's wrong. As far as I can tell, it cannot fail here. Clean it up anyway, by removing the useless conversion. Signed-off-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Kevin Wolf <kwolf@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2018-06-15block: Fix -blockdev for certain non-string scalarsMarkus Armbruster
Configuration flows through the block subsystem in a rather peculiar way. Configuration made with -drive enters it as QemuOpts. Configuration made with -blockdev / blockdev-add enters it as QAPI type BlockdevOptions. The block subsystem uses QDict, QemuOpts and QAPI types internally. The precise flow is next to impossible to explain (I tried for this commit message, but gave up after wasting several hours). What I can explain is a flaw in the BlockDriver interface that leads to this bug: $ qemu-system-x86_64 -blockdev node-name=n1,driver=nfs,server.type=inet,server.host=localhost,path=/foo/bar,user=1234 qemu-system-x86_64: -blockdev node-name=n1,driver=nfs,server.type=inet,server.host=localhost,path=/foo/bar,user=1234: Internal error: parameter user invalid QMP blockdev-add is broken the same way. Here's what happens. The block layer passes configuration represented as flat QDict (with dotted keys) to BlockDriver methods .bdrv_file_open(). The QDict's members are typed according to the QAPI schema. nfs_file_open() converts it to QAPI type BlockdevOptionsNfs, with qdict_crumple() and a qobject input visitor. This visitor comes in two flavors. The plain flavor requires scalars to be typed according to the QAPI schema. That's the case here. The keyval flavor requires string scalars. That's not the case here. nfs_file_open() uses the latter, and promptly falls apart for members @user, @group, @tcp-syn-count, @readahead-size, @page-cache-size, @debug. Switching to the plain flavor would fix -blockdev, but break -drive, because there the scalars arrive in nfs_file_open() as strings. The proper fix would be to replace the QDict by QAPI type BlockdevOptions in the BlockDriver interface. Sadly, that's beyond my reach right now. Next best would be to fix the block layer to always pass correctly typed QDicts to the BlockDriver methods. Also beyond my reach. What I can do is throw another hack onto the pile: have nfs_file_open() convert all members to string, so use of the keyval flavor actually works, by replacing qdict_crumple() by new function qdict_crumple_for_keyval_qiv(). The pattern "pass result of qdict_crumple() to qobject_input_visitor_new_keyval()" occurs several times more: * qemu_rbd_open() Same issue as nfs_file_open(), but since BlockdevOptionsRbd has only string members, its only a latent bug. Fix it anyway. * parallels_co_create_opts(), qcow_co_create_opts(), qcow2_co_create_opts(), bdrv_qed_co_create_opts(), sd_co_create_opts(), vhdx_co_create_opts(), vpc_co_create_opts() These work, because they create the QDict with qemu_opts_to_qdict_filtered(), which creates only string scalars. The function sports a TODO comment asking for better typing; that's going to be fun. Use qdict_crumple_for_keyval_qiv() to be safe. Signed-off-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Kevin Wolf <kwolf@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2018-06-15block: Add block-specific QDict headerMax Reitz
There are numerous QDict functions that have been introduced for and are used only by the block layer. Move their declarations into an own header file to reflect that. While qdict_extract_subqdict() is in fact used outside of the block layer (in util/qemu-config.c), it is still a function related very closely to how the block layer works with nested QDicts, namely by sometimes flattening them. Therefore, its declaration is put into this header as well and util/qemu-config.c includes it with a comment stating exactly which function it needs. Suggested-by: Markus Armbruster <armbru@redhat.com> Signed-off-by: Max Reitz <mreitz@redhat.com> Message-Id: <20180509165530.29561-7-mreitz@redhat.com> [Copyright note tweaked, superfluous includes dropped] Signed-off-by: Markus Armbruster <armbru@redhat.com> Reviewed-by: Kevin Wolf <kwolf@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2018-05-15block: Merge .bdrv_co_writev{,_flags} in driversEric Blake
We have too many driver callback interfaces; simplify the mess somewhat by merging the flags parameter of .bdrv_co_writev_flags() into .bdrv_co_writev(). Note that as long as a driver doesn't set .supported_write_flags, the flags argument will be 0 and behavior is identical. Also note that the public function bdrv_co_writev() still lacks a flags argument; so the driver signature is thus intentionally slightly different. But that's not the end of the world, nor the first time that the driver interface differs slightly from the public interface. Ideally, we should be rewriting all of these drivers to use modern byte-based interfaces. But that's a more invasive patch to write and audit, compared to the simplification done here. Signed-off-by: Eric Blake <eblake@redhat.com> Reviewed-by: Daniel P. Berrangé <berrange@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2018-05-04qobject: Replace qobject_incref/QINCREF qobject_decref/QDECREFMarc-André Lureau
Now that we can safely call QOBJECT() on QObject * as well as its subtypes, we can have macros qobject_ref() / qobject_unref() that work everywhere instead of having to use QINCREF() / QDECREF() for QObject and qobject_incref() / qobject_decref() for its subtypes. The replacement is mechanical, except I broke a long line, and added a cast in monitor_qmp_cleanup_req_queue_locked(). Unlike qobject_decref(), qobject_unref() doesn't accept void *. Note that the new macros evaluate their argument exactly once, thus no need to shout them. Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Message-Id: <20180419150145.24795-4-marcandre.lureau@redhat.com> Reviewed-by: Markus Armbruster <armbru@redhat.com> [Rebased, semantic conflict resolved, commit message improved] Signed-off-by: Markus Armbruster <armbru@redhat.com>
2018-03-26parallels: Check maximum cluster size on createKevin Wolf
It's unclear what the real maximum cluster size is for the Parallels format, but let's at least make sure that we don't get integer overflows in our .bdrv_co_create implementation. Signed-off-by: Kevin Wolf <kwolf@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com>
2018-03-19qapi: Replace qobject_to_X(o) by qobject_to(X, o)Max Reitz
This patch was generated using the following Coccinelle script: @@ expression Obj; @@ ( - qobject_to_qnum(Obj) + qobject_to(QNum, Obj) | - qobject_to_qstring(Obj) + qobject_to(QString, Obj) | - qobject_to_qdict(Obj) + qobject_to(QDict, Obj) | - qobject_to_qlist(Obj) + qobject_to(QList, Obj) | - qobject_to_qbool(Obj) + qobject_to(QBool, Obj) ) and a bit of manual fix-up for overly long lines and three places in tests/check-qjson.c that Coccinelle did not find. Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Alberto Garcia <berto@igalia.com> Message-Id: <20180224154033.29559-4-mreitz@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> [eblake: swap order from qobject_to(o, X), rebase to master, also a fix to latent false-positive compiler complaint about hw/i386/acpi-build.c] Signed-off-by: Eric Blake <eblake@redhat.com>
2018-03-19parallels: Support .bdrv_co_createKevin Wolf
This adds the .bdrv_co_create driver callback to parallels, which enables image creation over QMP. Signed-off-by: Kevin Wolf <kwolf@redhat.com> Reviewed-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Jeff Cody <jcody@redhat.com>
2018-03-09block: convert bdrv_check callback to coroutine_fnPaolo Bonzini
Suggested-by: Kevin Wolf <kwolf@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Message-Id: <1516279431-30424-8-git-send-email-pbonzini@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2018-03-02block: rename .bdrv_create() to .bdrv_co_create_opts()Stefan Hajnoczi
BlockDriver->bdrv_create() has been called from coroutine context since commit 5b7e1542cfa41a281af9629d31cef03704d976e6 ("block: make bdrv_create adopt coroutine"). Make this explicit by renaming to .bdrv_co_create_opts() and add the coroutine_fn annotation. This makes it obvious to block driver authors that they may yield, use CoMutex, or other coroutine_fn APIs. bdrv_co_create is reserved for the QAPI-based version that Kevin is working on. Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> Message-Id: <20170705102231.20711-2-stefanha@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2018-03-02parallels: Switch to .bdrv_co_block_status()Eric Blake
We are gradually moving away from sector-based interfaces, towards byte-based. Update the parallels driver accordingly. Note that the internal function block_status() is still sector-based, because it is still in use by other sector-based functions; but that's okay because request_alignment is 512 as a result of those functions. For now, no optimizations are added based on the mapping hint. Signed-off-by: Eric Blake <eblake@redhat.com> Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Reviewed-by: Fam Zheng <famz@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2018-02-09Move include qemu/option.h from qemu-common.h to actual usersMarkus Armbruster
qemu-common.h includes qemu/option.h, but most places that include the former don't actually need the latter. Drop the include, and add it to the places that actually need it. While there, drop superfluous includes of both headers, and separate #include from file comment with a blank line. This cleanup makes the number of objects depending on qemu/option.h drop from 4545 (out of 4743) to 284 in my "build everything" tree. Reviewed-by: Eric Blake <eblake@redhat.com> Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org> Signed-off-by: Markus Armbruster <armbru@redhat.com> Message-Id: <20180201111846.21846-20-armbru@redhat.com> [Semantic conflict with commit bdd6a90a9e in block/nvme.c resolved]
2018-01-22block/parallels: add backing support to readv/writevEdgar Kaziakhmedov
Since parallels format supports backing files, refine readv/writev (allocate_clusters) to redirect read/write requests to a backing file (if cluster is not available in the current bs). Signed-off-by: Edgar Kaziakhmedov <edgar.kaziakhmedov@virtuozzo.com> Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: Klim Kireev <klim.kireev@virtuozzo.com> Message-id: 20180112090122.1702-6-klim.kireev@virtuozzo.com CC: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2018-01-22block/parallels: replace some magic numbersKlim Kireev
Signed-off-by: Klim Kireev <klim.kireev@virtuozzo.com> Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Signed-off-by: Edgar Kaziakhmedov <edgar.kaziakhmedov@virtuozzo.com> Message-id: 20180112090122.1702-5-klim.kireev@virtuozzo.com CC: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2018-01-22block/parallels: move some structures into headerKlim Kireev
To implement xml format, some defines and structures from parallels.c are required. Signed-off-by: Klim Kireev <klim.kireev@virtuozzo.com> Reviewed-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Signed-off-by: Denis V. Lunev <den@openvz.org> Signed-off-by: Vladimir Sementsov-Ogievskiy <vsementsov@virtuozzo.com> Signed-off-by: Edgar Kaziakhmedov <edgar.kaziakhmedov@virtuozzo.com> Message-id: 20180112090122.1702-4-klim.kireev@virtuozzo.com CC: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
2017-11-14block/parallels: add migration blockerJeff Cody
Migration does not work for parallels, and has been broken for a while (see patch 'block/parallels: Do not update header or truncate image when INMIGRATE'). The bdrv_invalidate_cache() method needs to be added for migration to be supported. Until this is done, prohibit migration. Signed-off-by: Jeff Cody <jcody@redhat.com> Reviewed-by: Fam Zheng <famz@redhat.com> Message-id: 5e04a7c8a3089913fa58d484af42dab7993984ad.1510059970.git.jcody@redhat.com Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Reviewed-by: Denis V. Lunev <den@openvz.org> Signed-off-by: Max Reitz <mreitz@redhat.com>
2017-11-14block/parallels: Do not update header or truncate image when INMIGRATEJeff Cody
If we write or modify the image file while the QEMU run state is INMIGRATE, then the BDRV_O_INACTIVE BDS flag is set. This will cause an assert, since the image is marked inactive. Make sure we obey this flag. Tested-by: Alexey Kardashevskiy <aik@ozlabs.ru> Signed-off-by: Jeff Cody <jcody@redhat.com> Message-id: 3996c930fa8cde8570b7a63032720d76a28fd78b.1510059970.git.jcody@redhat.com Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Reviewed-by: Denis V. Lunev <den@openvz.org> Signed-off-by: Max Reitz <mreitz@redhat.com>
2017-09-04qapi: drop the sentinel in enum arrayMarc-André Lureau
Now that all usages have been converted to user lookup helpers. Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Message-Id: <20170822132255.23945-14-marcandre.lureau@redhat.com> [Rebased, superfluous local variable dropped, missing check-qom-proplist.c update added] Signed-off-by: Markus Armbruster <armbru@redhat.com> Message-Id: <1503564371-26090-17-git-send-email-armbru@redhat.com>
2017-09-04qapi: Change data type of the FOO_lookup generated for enum FOOMarc-André Lureau
Currently, a FOO_lookup is an array of strings terminated by a NULL sentinel. A future patch will generate enums with "holes". NULL-termination will cease to work then. To prepare for that, store the length in the FOO_lookup by wrapping it in a struct and adding a member for the length. The sentinel will be dropped next. Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com> Message-Id: <20170822132255.23945-13-marcandre.lureau@redhat.com> [Basically redone] Signed-off-by: Markus Armbruster <armbru@redhat.com> Message-Id: <1503564371-26090-16-git-send-email-armbru@redhat.com> [Rebased]
2017-09-04qapi: Generate FOO_str() macro for QAPI enum FOOMarkus Armbruster
The next commit will put it to use. May look pointless now, but we're going to change the FOO_lookup's type, and then it'll help. Signed-off-by: Markus Armbruster <armbru@redhat.com> Message-Id: <1503564371-26090-13-git-send-email-armbru@redhat.com> Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com>
2017-09-04qapi: Drop superfluous qapi_enum_parse() parameter maxMarkus Armbruster
The lookup tables have a sentinel, no need to make callers pass their size. Signed-off-by: Markus Armbruster <armbru@redhat.com> Message-Id: <1503564371-26090-3-git-send-email-armbru@redhat.com> Reviewed-by: Marc-André Lureau <marcandre.lureau@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com> [Rebased, commit message corrected]
2017-08-08parallels: drop check that bdrv_truncate() is workingDenis V. Lunev
This would be actually strange and error prone. If truncate() nowadays will fail, there is something fatally wrong. Let's check for that during the actual work. The only fallback case is when the file is not zero initialized. In this case we should switch to preallocation via fallocate(). Signed-off-by: Denis V. Lunev <den@openvz.org> CC: Markus Armbruster <armbru@redhat.com> CC: Kevin Wolf <kwolf@redhat.com> CC: Max Reitz <mreitz@redhat.com> CC: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com>
2017-08-08parallels: respect error code of bdrv_getlength() in allocate_clusters()Denis V. Lunev
If we can not get the file length, the state of BDS is broken completely. Return error to the caller. Signed-off-by: Denis V. Lunev <den@openvz.org> CC: Markus Armbruster <armbru@redhat.com> CC: Kevin Wolf <kwolf@redhat.com> CC: Max Reitz <mreitz@redhat.com> CC: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com> Reviewed-by: Eric Blake <eblake@redhat.com>
2017-07-11block: Add PreallocMode to blk_truncate()Max Reitz
blk_truncate() itself will pass that value to bdrv_truncate(), and all callers of blk_truncate() just set the parameter to PREALLOC_MODE_OFF for now. Signed-off-by: Max Reitz <mreitz@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Message-id: 20170613202107.10125-4-mreitz@redhat.com Signed-off-by: Max Reitz <mreitz@redhat.com>
generated by cgit v1.2.3 (git 2.26.2) at 2024-11-22 10:40:34 +0000