Age | Commit message (Collapse) | Author |
|
Rather than creating stubs for every command that just return
QERR_UNSUPPORTED, use 'if' conditions in the schema to fully
exclude generation of the filesystem trimming commands on POSIX
platforms lacking required APIs.
The command will be rejected at QMP dispatch time instead,
avoiding reimplementing rejection by blocking the stub commands.
This changes the error message for affected commands from
{"class": "CommandNotFound", "desc": "Command FOO has been disabled"}
to
{"class": "CommandNotFound", "desc": "The command FOO has not been found"}
This has the additional benefit that the QGA protocol reference
now documents what conditions enable use of the command.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-ID: <20240712132459.3974109-16-berrange@redhat.com>
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
|
|
Rather than creating stubs for every command that just return
QERR_UNSUPPORTED, use 'if' conditions in the QAPI schema to
fully exclude generation of the filesystem trimming commands
on POSIX platforms lacking required APIs.
The command will be rejected at QMP dispatch time instead,
avoiding reimplementing rejection by blocking the stub commands.
This changes the error message for affected commands from
{"class": "CommandNotFound", "desc": "Command FOO has been disabled"}
to
{"class": "CommandNotFound", "desc": "The command FOO has not been found"}
This has the additional benefit that the QGA protocol reference
now documents what conditions enable use of the command.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-ID: <20240712132459.3974109-15-berrange@redhat.com>
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
|
|
Rather than creating stubs for every command that just return
QERR_UNSUPPORTED, use 'if' conditions in the schema to fully
exclude generation of the filesystem freezing commands on POSIX
platforms lacking the required APIs.
The command will be rejected at QMP dispatch time instead,
avoiding reimplementing rejection by blocking the stub commands.
This changes the error message for affected commands from
{"class": "CommandNotFound", "desc": "Command FOO has been disabled"}
to
{"class": "CommandNotFound", "desc": "The command FOO has not been found"}
This has the additional benefit that the QGA protocol reference
now documents what conditions enable use of the command.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-ID: <20240712132459.3974109-14-berrange@redhat.com>
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
|
|
Rather than creating stubs for every command that just return
QERR_UNSUPPORTED, use 'if' conditions in the QAPI schema to
fully exclude generation of the commands on non-Windows.
The command will be rejected at QMP dispatch time instead,
avoiding reimplementing rejection by blocking the stub commands.
This changes the error message for affected commands from
{"class": "CommandNotFound", "desc": "Command FOO has been disabled"}
to
{"class": "CommandNotFound", "desc": "The command FOO has not been found"}
This has the additional benefit that the QGA protocol reference
now documents what conditions enable use of the command.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-ID: <20240712132459.3974109-13-berrange@redhat.com>
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
|
|
Some commands were blocked based on CONFIG_FSFREEZE, but their
impl had nothing todo with CONFIG_FSFREEZE, and were instead
either Linux-only, or Win+Linux-only.
Rather than creating stubs for every command that just return
QERR_UNSUPPORTED, use 'if' conditions in the QAPI schema to
fully exclude generation of the stats and fsinfo commands on
platforms that can't support them.
The command will be rejected at QMP dispatch time instead,
avoiding reimplementing rejection by blocking the stub commands.
This changes the error message for affected commands from
{"class": "CommandNotFound", "desc": "Command FOO has been disabled"}
to
{"class": "CommandNotFound", "desc": "The command FOO has not been found"}
This has the additional benefit that the QGA protocol reference
now documents what conditions enable use of the command.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-ID: <20240712132459.3974109-12-berrange@redhat.com>
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
|
|
Rather than creating stubs for every comamnd that just return
QERR_UNSUPPORTED, use 'if' conditions in the QAPI schema to
fully exclude generation of the network interface command on
POSIX platforms lacking getifaddrs().
The command will be rejected at QMP dispatch time instead,
avoiding reimplementing rejection by blocking the stub commands.
This changes the error message for affected commands from
{"class": "CommandNotFound", "desc": "Command FOO has been disabled"}
to
{"class": "CommandNotFound", "desc": "The command FOO has not been found"}
This has the additional benefit that the QGA protocol reference
now documents what conditions enable use of the command.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-ID: <20240712132459.3974109-11-berrange@redhat.com>
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
|
|
Rather than creating stubs for every command that just return
QERR_UNSUPPORTED, use 'if' conditions in the QAPI schema to
fully exclude generation of the commands on non-Linux POSIX
platforms
The command will be rejected at QMP dispatch time instead,
avoiding reimplementing rejection by blocking the stub commands.
This changes the error message for affected commands from
{"class": "CommandNotFound", "desc": "Command FOO has been disabled"}
to
{"class": "CommandNotFound", "desc": "The command FOO has not been found"}
This has the additional benefit that the QGA protocol reference
now documents what conditions enable use of the command.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-ID: <20240712132459.3974109-10-berrange@redhat.com>
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
|
|
Rather than creating stubs for every command that just return
QERR_UNSUPPORTED, use 'if' conditions in the QAPI schema to
fully exclude generation of the commands on Windows.
The command will be rejected at QMP dispatch time instead,
avoiding reimplementing rejection by blocking the stub commands.
This changes the error message for affected commands from
{"class": "CommandNotFound", "desc": "Command FOO has been disabled"}
to
{"class": "CommandNotFound", "desc": "The command FOO has not been found"}
This also fixes an accidental inconsistency where some commands
(guest-get-diskstats & guest-get-cpustats) are implemented as
stubs, yet not added to the blockedrpc list. Those change their
error message from
{"class": "GenericError, "desc": "this feature or command is not currently supported"}
to
{"class": "CommandNotFound", "desc": "The command FOO has not been found"}
The final additional benefit is that the QGA protocol reference
now documents what conditions enable use of the command.
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-ID: <20240712132459.3974109-9-berrange@redhat.com>
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
|
|
Defining these at the meson level allows them to be used a conditional
tests in the QAPI schemas.
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240712132459.3974109-8-berrange@redhat.com>
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
|
|
The qmp_guest_{set,get}_{memory_blocks,block_info} command impls in
commands-posix.c are surrounded by '#ifdef __linux__' so should
instead live in commands-linux.c
This also removes a "#ifdef CONFIG_LINUX" that was nested inside
a "#ifdef __linux__".
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-ID: <20240712132459.3974109-7-berrange@redhat.com>
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
|
|
The qmp_guest_{diskstats,cpustats} command impls in
commands-posix.c are surrounded by '#ifdef __linux__' so should
instead live in commands-linux.c
This also removes a "#ifdef CONFIG_LINUX" that was nested inside
a "#ifdef __linux__".
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Message-ID: <20240712132459.3974109-6-berrange@redhat.com>
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
|
|
The qmp_guest_{fstrim, get_fsinfo, get_disks} command impls in
commands-posix.c are surrounded by '#ifdef __linux__' so should
instead live in commands-linux.c
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-ID: <20240712132459.3974109-5-berrange@redhat.com>
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
|
|
The qmp_guest_suspend_{disk,ram,hybrid} command impls in
commands-posix.c are surrounded by '#ifdef __linux__' so should
instead live in commands-linux.c
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-ID: <20240712132459.3974109-4-berrange@redhat.com>
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
|
|
The qmp_guest_set_vcpus and qmp_guest_get_vcpus command impls in
commands-posix.c are surrounded by '#ifdef __linux__' so should
instead live in commands-linux.c
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Message-ID: <20240712132459.3974109-3-berrange@redhat.com>
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
|
|
This command has never existed in tree, since it was renamed to
guest-get-memory-block-info before being merged.
Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org>
Reviewed-by: Konstantin Kostiuk <kkostiuk@redhat.com>
Signed-off-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240712132459.3974109-2-berrange@redhat.com>
Signed-off-by: Konstantin Kostiuk <kkostiuk@redhat.com>
|
|
staging
pull-loongarch-20240719
# -----BEGIN PGP SIGNATURE-----
#
# iLMEAAEKAB0WIQS4/x2g0v3LLaCcbCxAov/yOSY+3wUCZpnSRQAKCRBAov/yOSY+
# 3+dmBACzIzU+nnCI0QANYJhEVekXUoo+UVa+PX4dk7OoACDSgq2nQkAQzUoqhzSj
# zjnxTmIevdcUqQ6eU24hNwOT7DEZBk0MIcTZMuG8DRc1wbSo46ORfVGWQkPtMQ25
# ADNS0q/TPnYMtMEfXn2xN/0QrpR99HN8wOVNmYH5/D6/zHMFOw==
# =Vo1H
# -----END PGP SIGNATURE-----
# gpg: Signature made Fri 19 Jul 2024 12:41:09 PM AEST
# gpg: using RSA key B8FF1DA0D2FDCB2DA09C6C2C40A2FFF239263EDF
# gpg: Good signature from "Song Gao <m17746591750@163.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: B8FF 1DA0 D2FD CB2D A09C 6C2C 40A2 FFF2 3926 3EDF
* tag 'pull-loongarch-20240719' of https://gitlab.com/gaosong/qemu:
hw/loongarch: Modify flash block size to 256K
hw/loongarch: Remove unimplemented extioi INT_encode mode
target/loongarch/gdbstub: Add vector registers support
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
loongarch added a common library for edk2 to
parse flash base addresses through fdt.
For compatibility with other architectures,
the flash block size in qemu is now changed to 256k.
Signed-off-by: Xianglai Li <lixianglai@loongson.cn>
Reviewed-by: Song Gao <gaosong@loongson.cn>
Message-Id: <20240624033319.999631-1-lixianglai@loongson.cn>
Signed-off-by: Song Gao <gaosong@loongson.cn>
|
|
Remove extioi INT_encode encode mode, because we don't emulate it.
Signed-off-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Bibo Mao <maobibo@loongson.cn>
Message-Id: <20240718083254.748179-1-gaosong@loongson.cn>
|
|
GDB already support LoongArch vector extension[1], QEMU gdb adds
LoongArch vector registers support, so that users can use 'info all-registers'
to get all vector registers values.
[1]: https://sourceware.org/git/?p=binutils-gdb.git;a=commitdiff;h=1e9569f383a3d5a88ee07d0c2401bd95613c222e
Signed-off-by: Song Gao <gaosong@loongson.cn>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewd-by: Bibo Mao <maobibo@loongson.cn>
Message-Id: <20240711024454.3075183-1-gaosong@loongson.cn>
|
|
https://git.linaro.org/people/pmaydell/qemu-arm into staging
target-arm queue:
* Fix handling of LDAPR/STLR with negative offset
* LDAPR should honour SCTLR_ELx.nAA
* Use float_status copy in sme_fmopa_s
* hw/display/bcm2835_fb: fix fb_use_offsets condition
* hw/arm/smmuv3: Support and advertise nesting
* Use FPST_F16 for SME FMOPA (widening)
* tests/arm-cpu-features: Do not assume PMU availability
* hvf: arm: Do not advance PC when raising an exception
# -----BEGIN PGP SIGNATURE-----
#
# iQJNBAABCAA3FiEE4aXFk81BneKOgxXPPCUl7RQ2DN4FAmaZFlUZHHBldGVyLm1h
# eWRlbGxAbGluYXJvLm9yZwAKCRA8JSXtFDYM3iJuEACtVh1Wp93XMsL3llAZkQlx
# DUCnDCvAM2qiiTIMOqPQzeKTIkRV9aFh1YWzOtMFKai6UkBU6p1b4bPqb5SIr99G
# Ayps4+WzAHsjTqBGEpIIDWL6GqMwv9azBnRAYNb+Cg9O3SzEnCdGOKCfGYTXXPRz
# zQ1NIgqZSUC5jg3XgkU22J3VMsOUWijbzxnGXhOyemSIEhREl+t6Ns3ca3n47/jk
# JIw1g6o0mpefPPkaLq6ftVwpn1L63iYQugn4VCrIhtIoOM8vmnShbI9/GwzL4AYk
# n28nwPl948Xby13kCYmu6Slt8Rmm7M33pBDJzsVtbaeBSd44XHrov8Y1+e1FhAco
# lxrWY/2rG9HiWKGLdAeCKwVxB186DKiTmuK7lcN+eBu3VbOLjDiVE0d1bK4HqGyc
# nzA/Aq81Y9p5Z7wzX40sVFlq0j1pQDQWk6GgPfMA4ueHKEEobxC3C+k1q9m02gjQ
# qesOFzViiGe0j7JER84qqcatIaTk09xfbXL/uMZx8oP/iKa1pyMUx2blChXOXVTx
# oGkO2h3/QCpRIos8d8WM/bso16EkpraInM4748iumSLuxDxTwiIikK/hpsCLDwUN
# dLsH/hAMz+yQOFubFoRt4IlsGVnk5asmTDMb4S8RojdF2KzHuzbJMgdEOe62631g
# IOAc7Tn3TIm5MpAxXOXgJA==
# =/aEm
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 18 Jul 2024 11:19:17 PM AEST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [full]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [full]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [full]
# gpg: aka "Peter Maydell <peter@archaic.org.uk>" [unknown]
* tag 'pull-target-arm-20240718' of https://git.linaro.org/people/pmaydell/qemu-arm: (26 commits)
hvf: arm: Do not advance PC when raising an exception
tests/arm-cpu-features: Do not assume PMU availability
tests/tcg/aarch64: Add test cases for SME FMOPA (widening)
target/arm: Use FPST_F16 for SME FMOPA (widening)
target/arm: Use float_status copy in sme_fmopa_s
hw/arm/smmu: Refactor SMMU OAS
hw/arm/smmuv3: Support and advertise nesting
hw/arm/smmuv3: Handle translation faults according to SMMUPTWEventInfo
hw/arm/smmuv3: Support nested SMMUs in smmuv3_notify_iova()
hw/arm/smmu: Support nesting in the rest of commands
hw/arm/smmu: Introduce smmu_iotlb_inv_asid_vmid
hw/arm/smmu: Support nesting in smmuv3_range_inval()
hw/arm/smmu-common: Support nested translation
hw/arm/smmu-common: Add support for nested TLB
hw/arm/smmu-common: Rework TLB lookup for nesting
hw/arm/smmuv3: Translate CD and TT using stage-2 table
hw/arm/smmu: Introduce CACHED_ENTRY_TO_ADDR
hw/arm/smmu: Consolidate ASID and VMID types
hw/arm/smmu: Split smmuv3_translate()
hw/arm/smmu: Use enum for SMMU stage
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
hvf did not advance PC when raising an exception for most unhandled
system registers, but it mistakenly advanced PC when raising an
exception for GICv3 registers.
Cc: qemu-stable@nongnu.org
Fixes: a2260983c655 ("hvf: arm: Add support for GICv3")
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Message-id: 20240716-pmu-v3-4-8c7c1858a227@daynix.com
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Asahi Linux supports KVM but lacks PMU support.
Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240716-pmu-v3-1-8c7c1858a227@daynix.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Signed-off-by: Daniyal Khan <danikhan632@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20240717060149.204788-4-richard.henderson@linaro.org
Message-Id: 172090222034.13953.16888708708822922098-1@git.sr.ht
[rth: Split test from a larger patch, tidy assembly]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
This operation has float16 inputs and thus must use
the FZ16 control not the FZ control.
Cc: qemu-stable@nongnu.org
Fixes: 3916841ac75 ("target/arm: Implement FMOPA, FMOPS (widening)")
Reported-by: Daniyal Khan <danikhan632@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20240717060149.204788-3-richard.henderson@linaro.org
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2374
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
We made a copy above because the fp exception flags
are not propagated back to the FPST register, but
then failed to use the copy.
Cc: qemu-stable@nongnu.org
Fixes: 558e956c719 ("target/arm: Implement FMOPA, FMOPS (non-widening)")
Signed-off-by: Daniyal Khan <danikhan632@gmail.com>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20240717060149.204788-2-richard.henderson@linaro.org
[rth: Split from a larger patch]
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
SMMUv3 OAS is currently hardcoded in the code to 44 bits, for nested
configurations that can be a problem, as stage-2 might be shared with
the CPU which might have different PARANGE, and according to SMMU manual
ARM IHI 0070F.b:
6.3.6 SMMU_IDR5, OAS must match the system physical address size.
This patch doesn't change the SMMU OAS, but refactors the code to
make it easier to do that:
- Rely everywhere on IDR5 for reading OAS instead of using the
SMMU_IDR5_OAS macro, so, it is easier just to change IDR5 and
it propagages correctly.
- Add additional checks when OAS is greater than 48bits.
- Remove unused functions/macros: pa_range/MAX_PA.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20240715084519.1189624-19-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Everything is in place, consolidate parsing of STE cfg and setting
translation stage.
Advertise nesting if stage requested is "nested".
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20240715084519.1189624-18-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Previously, to check if faults are enabled, it was sufficient to check
the current stage of translation and check the corresponding
record_faults flag.
However, with nesting, it is possible for stage-1 (nested) translation
to trigger a stage-2 fault, so we check SMMUPTWEventInfo as it would
have the correct stage set from the page table walk.
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20240715084519.1189624-17-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
IOMMUTLBEvent only understands IOVA, for stage-1 or stage-2
SMMU instances we consider the input address as the IOVA, but when
nesting is used, we can't mix stage-1 and stage-2 addresses, so for
nesting only stage-1 is considered the IOVA and would be notified.
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20240715084519.1189624-16-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Some commands need rework for nesting, as they used to assume S1
and S2 are mutually exclusive:
- CMD_TLBI_NH_ASID: Consider VMID if stage-2 is supported
- CMD_TLBI_NH_ALL: Consider VMID if stage-2 is supported, otherwise
invalidate everything, this required a new vmid invalidation
function for stage-1 only (ASID >= 0)
Also, rework trace events to reflect the new implementation.
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20240715084519.1189624-15-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Soon, Instead of doing TLB invalidation by ASID only, VMID will be
also required.
Add smmu_iotlb_inv_asid_vmid() which invalidates by both ASID and VMID.
However, at the moment this function is only used in SMMU_CMD_TLBI_NH_ASID
which is a stage-1 command, so passing VMID = -1 keeps the original
behaviour.
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20240715084519.1189624-14-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
With nesting, we would need to invalidate IPAs without
over-invalidating stage-1 IOVAs. This can be done by
distinguishing IPAs in the TLBs by having ASID=-1.
To achieve that, rework the invalidation for IPAs to have a
separate function, while for IOVA invalidation ASID=-1 means
invalidate for all ASIDs.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20240715084519.1189624-13-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
When nested translation is requested, do the following:
- Translate stage-1 table address IPA into PA through stage-2.
- Translate stage-1 table walk output (IPA) through stage-2.
- Create a single TLB entry from stage-1 and stage-2 translations
using logic introduced before.
smmu_ptw() has a new argument SMMUState which include the TLB as
stage-1 table address can be cached in there.
Also in smmu_ptw(), a separate path used for nesting to simplify the
code, although some logic can be combined.
With nested translation class of translation fault can be different,
from the class of the translation, as faults from translating stage-1
tables are considered as CLASS_TT and not CLASS_IN, a new member
"is_ipa_descriptor" added to "SMMUPTWEventInfo" to differ faults
from walking stage 1 translation table and faults from translating
an IPA for a transaction.
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20240715084519.1189624-12-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
This patch adds support for nested (combined) TLB entries.
The main function combine_tlb() is not used here but in the next
patches, but to simplify the patches it is introduced first.
Main changes:
1) New field added in the SMMUTLBEntry struct: parent_perm, for
nested TLB, holds the stage-2 permission, this can be used to know
the origin of a permission fault from a cached entry as caching
the “and” of the permissions loses this information.
SMMUPTWEventInfo is used to hold information about PTW faults so
the event can be populated, the value of stage used to be set
based on the current stage for TLB permission faults, however
with the parent_perm, it is now set based on which perm has
the missing permission
When nesting is not enabled it has the same value as perm which
doesn't change the logic.
2) As combined TLB implementation is used, the combination logic
chooses:
- tg and level from the entry which has the smallest addr_mask.
- Based on that the iova that would be cached is recalculated.
- Translated_addr is chosen from stage-2.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20240715084519.1189624-11-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
In the next patch, combine_tlb() will be added which combines 2 TLB
entries into one for nested translations, which chooses the granule
and level from the smallest entry.
This means that with nested translation, an entry can be cached with
the granule of stage-2 and not stage-1.
However, currently, the lookup for an IOVA is done with input stage
granule, which is stage-1 for nested configuration, which will not
work with the above logic.
This patch reworks lookup in that case, so it falls back to stage-2
granule if no entry is found using stage-1 granule.
Also, drop aligning the iova to avoid over-aligning in case the iova
is cached with a smaller granule, the TLB lookup will align the iova
anyway for each granule and level, and the page table walker doesn't
consider the page offset bits.
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20240715084519.1189624-10-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
According to ARM SMMU architecture specification (ARM IHI 0070 F.b),
In "5.2 Stream Table Entry":
[51:6] S1ContextPtr
If Config[1] == 1 (stage 2 enabled), this pointer is an IPA translated by
stage 2 and the programmed value must be within the range of the IAS.
In "5.4.1 CD notes":
The translation table walks performed from TTB0 or TTB1 are always performed
in IPA space if stage 2 translations are enabled.
This patch implements translation of the S1 context descriptor pointer and
TTBx base addresses through the S2 stage (IPA -> PA)
smmuv3_do_translate() is updated to have one arg which is translation
class, this is useful to:
- Decide wether a translation is stage-2 only or use the STE config.
- Populate the class in case of faults, WALK_EABT is left unchanged
for stage-1 as it is always IN, while stage-2 would match the
used class (TT, IN, CD), this will change slightly when the ptw
supports nested translation as it can also issue TT event with
class IN.
In case for stage-2 only translation, used in the context of nested
translation, the stage and asid are saved and restored before and
after calling smmu_translate().
Translating CD or TTBx can fail for the following reasons:
1) Large address size: This is described in
(3.4.3 Address sizes of SMMU-originated accesses)
- For CD ptr larger than IAS, for SMMUv3.1, it can trigger either
C_BAD_STE or Translation fault, we implement the latter as it
requires no extra code.
- For TTBx, if larger than the effective stage 1 output address size, it
triggers C_BAD_CD.
2) Faults from PTWs (7.3 Event records)
- F_ADDR_SIZE: large address size after first level causes stage 2 Address
Size fault (Also in 3.4.3 Address sizes of SMMU-originated accesses)
- F_PERMISSION: Same as an address translation. However, when
CLASS == CD, the access is implicitly Data and a read.
- F_ACCESS: Same as an address translation.
- F_TRANSLATION: Same as an address translation.
- F_WALK_EABT: Same as an address translation.
These are already implemented in the PTW logic, so no extra handling
required.
As in CD and TTBx translation context, the iova is not known, setting
the InputAddr was removed from "smmuv3_do_translate" and set after
from "smmuv3_translate" with the new function "smmuv3_fixup_event"
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20240715084519.1189624-9-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Soon, smmuv3_do_translate() will be used to translate the CD and the
TTBx, instead of re-writting the same logic to convert the returned
cached entry to an address, add a new macro CACHED_ENTRY_TO_ADDR.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20240715084519.1189624-8-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
ASID and VMID used to be uint16_t in the translation config, however,
in other contexts they can be int as -1 in case of TLB invalidation,
to represent all (don’t care).
When stage-2 was added asid was set to -1 in stage-2 and vmid to -1
in stage-1 configs. However, that meant they were set as (65536),
this was not an issue as nesting was not supported and no
commands/lookup uses both.
With nesting, it’s critical to get this right as translation must be
tagged correctly with ASID/VMID, and with ASID=-1 meaning stage-2.
Represent ASID/VMID everywhere as int.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20240715084519.1189624-7-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
smmuv3_translate() does everything from STE/CD parsing to TLB lookup
and PTW.
Soon, when nesting is supported, stage-1 data (tt, CD) needs to be
translated using stage-2.
Split smmuv3_translate() to 3 functions:
- smmu_translate(): in smmu-common.c, which does the TLB lookup, PTW,
TLB insertion, all the functions are already there, this just puts
them together.
This also simplifies the code as it consolidates event generation
in case of TLB lookup permission failure or in TT selection.
- smmuv3_do_translate(): in smmuv3.c, Calls smmu_translate() and does
the event population in case of errors.
- smmuv3_translate(), now calls smmuv3_do_translate() for
translation while the rest is the same.
Also, add stage in trace_smmuv3_translate_success()
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20240715084519.1189624-6-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Currently, translation stage is represented as an int, where 1 is stage-1 and
2 is stage-2, when nested is added, 3 would be confusing to represent nesting,
so we use an enum instead.
While keeping the same values, this is useful for:
- Doing tricks with bit masks, where BIT(0) is stage-1 and BIT(1) is
stage-2 and both is nested.
- Tracing, as stage is printed as int.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Alex Bennée <alex.bennee@linaro.org>
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Message-id: 20240715084519.1189624-5-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The SMMUv3 spec (ARM IHI 0070 F.b - 7.3 Event records) defines the
class of events faults as:
CLASS: The class of the operation that caused the fault:
- 0b00: CD, CD fetch.
- 0b01: TTD, Stage 1 translation table fetch.
- 0b10: IN, Input address
However, this value was not set and left as 0 which means CD and not
IN (0b10).
Another problem was that stage-2 class is considered IN not TT for
EABT, according to the spec:
Translation of an IPA after successful stage 1 translation (or,
in stage 2-only configuration, an input IPA)
- S2 == 1 (stage 2), CLASS == IN (Input to stage)
This would change soon when nested translations are supported.
While at it, add an enum for class as it would be used for nesting.
However, at the moment stage-1 and stage-2 use the same class values,
except for EABT.
Fixes: 9bde7f0674 “hw/arm/smmuv3: Implement translate callback”
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Message-id: 20240715084519.1189624-4-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
For the following events (ARM IHI 0070 F.b - 7.3 Event records):
- F_TRANSLATION
- F_ACCESS
- F_PERMISSION
- F_ADDR_SIZE
If fault occurs at stage 2, S2 == 1 and:
- If translating an IPA for a transaction (whether by input to
stage 2-only configuration, or after successful stage 1 translation),
CLASS == IN, and IPA is provided.
At the moment only CLASS == IN is used which indicates input
translation.
However, this was not implemented correctly, as for stage 2, the code
only sets the S2 bit but not the IPA.
This field has the same bits as FetchAddr in F_WALK_EABT which is
populated correctly, so we don’t change that.
The setting of this field should be done from the walker as the IPA address
wouldn't be known in case of nesting.
For stage 1, the spec says:
If fault occurs at stage 1, S2 == 0 and:
CLASS == IN, IPA is UNKNOWN.
So, no need to set it to for stage 1, as ptw_info is initialised by zero in
smmuv3_translate().
Fixes: e703f7076a “hw/arm/smmuv3: Add page table walk for stage-2”
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Message-id: 20240715084519.1189624-3-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
According to the SMMU architecture specification (ARM IHI 0070 F.b),
in “3.4 Address sizes”
The address output from the translation causes a stage 1 Address Size
fault if it exceeds the range of the effective IPA size for the given CD.
However, this check was missing.
There is already a similar check for stage-2 against effective PA.
Reviewed-by: Jean-Philippe Brucker <jean-philippe@linaro.org>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Message-id: 20240715084519.1189624-2-smostafa@google.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
It is common practice when implementing double-buffering on VideoCore
to do so by multiplying the height of the virtual buffer by the
number of virtual screens desired (i.e., two - in the case of
double-bufferring).
At present, this won't work in QEMU because the logic in
fb_use_offsets require that both the virtual width and height exceed
their physical counterparts.
This appears to be unintentional/a typo and indeed the comment
states; "Experimentally, the hardware seems to do this only if the
viewport size is larger than the physical screen". The
viewport/virtual size would be larger than the physical size if
either virtual dimension were larger than their physical counterparts
and not necessarily both.
Signed-off-by: SamJakob <me@samjakob.com>
Message-id: 20240713160353.62410-1-me@samjakob.com
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
In commit c1a1f80518d360b when we added the FEAT_LSE2 relaxations to
the alignment requirements for atomic and ordered loads and stores,
we didn't quite get it right for LDAPR/LDAPRH/LDAPRB with no
immediate offset. These instructions were handled in the old decoder
as part of disas_ldst_atomic(), but unlike all the other insns that
function decoded (LDADD, LDCLR, etc) these insns are "ordered", not
"atomic", so they should be using check_ordered_align() rather than
check_atomic_align(). Commit c1a1f80518d360b used
check_atomic_align() regardless for everything in
disas_ldst_atomic(). We then carried that incorrect check over in
the decodetree conversion, where LDAPR/LDAPRH/LDAPRB are now handled
by trans_LDAPR().
The effect is that when FEAT_LSE2 is implemented, these instructions
don't honour the SCTLR_ELx.nAA bit and will generate alignment
faults when they should not.
(The LDAPR insns with an immediate offset were in disas_ldst_ldapr_stlr()
and then in trans_LDAPR_i() and trans_STLR_i(), and have always used
the correct check_ordered_align().)
Use check_ordered_align() in trans_LDAPR().
Cc: qemu-stable@nongnu.org
Fixes: c1a1f80518d360b ("target/arm: Relax ordered/atomic alignment checks for LSE2")
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240709134504.3500007-3-peter.maydell@linaro.org
|
|
When we converted the LDAPR/STLR instructions to decodetree we
accidentally introduced a regression where the offset is negative.
The 9-bit immediate field is signed, and the old hand decoder
correctly used sextract32() to get it out of the insn word,
but the ldapr_stlr_i pattern in the decode file used "imm:9"
instead of "imm:s9", so it treated the field as unsigned.
Fix the pattern to treat the field as a signed immediate.
Cc: qemu-stable@nongnu.org
Fixes: 2521b6073b7 ("target/arm: Convert LDAPR/STLR (imm) to decodetree")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2419
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20240709134504.3500007-2-peter.maydell@linaro.org
|
|
https://github.com/alistair23/qemu into staging
RISC-V PR for 9.1
* Support the zimop, zcmop, zama16b and zabha extensions
* Validate the mode when setting vstvec CSR
* Add decode support for Zawrs extension
* Update the KVM regs to Linux 6.10-rc5
* Add smcntrpmf extension support
* Raise an exception when CSRRS/CSRRC writes a read-only CSR
* Re-insert and deprecate 'riscv,delegate' in virt machine device tree
* roms/opensbi: Update to v1.5
# -----BEGIN PGP SIGNATURE-----
#
# iQIzBAABCAAdFiEEaukCtqfKh31tZZKWr3yVEwxTgBMFAmaYeUcACgkQr3yVEwxT
# gBMtdw//U2NbmnmECa0uXuE7fdFul0tUkl2oHb9Cr8g5Se5g/HVFqexAKOFZ8Lcm
# DvTl94zJ2dms4RntcmJHwTIusa+oU6qqOekediotjgpeH4BHZNCOHe0E9hIAHn9F
# uoJ1P186L7VeVr7OFAAgSCE7F6egCk7iC0h8L8/vuL4xcuyfbZ2r7ybiTl1+45N2
# YBBv5/00wsYnyMeqRYYtyqgX9QR017JRqNSfTJSbKxhQM/L1GA1xxisUvIGeyDqc
# Pn8E3dMN6sscR6bPs4RP+SBi0JIlRCgth/jteSUkbYf42osw3/5sl4oK/e6Xiogo
# SjELOF7QJNxE8H6EUIScDaCVB5ZhvELZcuOL2NRdUuVDkjhWXM633HwfEcXkZdFK
# W/H9wOvNxPAJIOGXOpv10+MLmhdyIOZwE0uk6evHvdcTn3FP9DurdUCc1se0zKOA
# Qg/H6usTbLGNQ7KKTNQ6GpQ6u89iE1CIyZqYVvB1YuF5t7vtAmxvNk3SVZ6aq3VL
# lPJW2Zd1eO09Q+kRnBVDV7MV4OJrRNsU+ryd91NrSVo9aLADtyiNC28dCSkjU3Gn
# 6YQZt65zHuhH5IBB/PGIPo7dLRT8KNWOiYVoy3c6p6DC6oXsKIibh0ue1nrVnnVQ
# NRqyxPYaj6P8zzqwTk+iJj36UXZZVtqPIhtRu9MrO6Opl2AbsXI=
# =pM6B
# -----END PGP SIGNATURE-----
# gpg: Signature made Thu 18 Jul 2024 12:09:11 PM AEST
# gpg: using RSA key 6AE902B6A7CA877D6D659296AF7C95130C538013
# gpg: Good signature from "Alistair Francis <alistair@alistair23.me>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 6AE9 02B6 A7CA 877D 6D65 9296 AF7C 9513 0C53 8013
* tag 'pull-riscv-to-apply-20240718-1' of https://github.com/alistair23/qemu: (30 commits)
roms/opensbi: Update to v1.5
hw/riscv/virt.c: re-insert and deprecate 'riscv,delegate'
target/riscv: raise an exception when CSRRS/CSRRC writes a read-only CSR
target/riscv: Expose the Smcntrpmf config
target/riscv: Do not setup pmu timer if OF is disabled
target/riscv: More accurately model priv mode filtering.
target/riscv: Start counters from both mhpmcounter and mcountinhibit
target/riscv: Enforce WARL behavior for scounteren/hcounteren
target/riscv: Save counter values during countinhibit update
target/riscv: Implement privilege mode filtering for cycle/instret
target/riscv: Only set INH fields if priv mode is available
target/riscv: Add cycle & instret privilege mode filtering support
target/riscv: Add cycle & instret privilege mode filtering definitions
target/riscv: Add cycle & instret privilege mode filtering properties
target/riscv: Fix the predicate functions for mhpmeventhX CSRs
target/riscv: Combine set_mode and set_virt functions.
target/riscv/kvm: update KVM regs to Linux 6.10-rc5
disas/riscv: Add decode for Zawrs extension
target/riscv: Validate the mode in write_vstvec
disas/riscv: Support zabha disassemble
...
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
Update OpenSBI and the pre-built opensbi32 and opensbi64 images to
v1.5.
The following commits were included in v1.5:
455de67 include: Bump-up version to 1.5
23b7bad lib: sbi: check incoming dbtr shmem address
0e45b63 docs: Fix wrong filename
caae2f7 lib: sbi: fwft: return SBI_EINVAL rather than SBI_ERR_INVALID_PARAM
e8717d1 lib: sbi: fwft: check feature value to be exactly 1 or 0
ecef14d lib: sbi: implement SBI FWFT extension
e9ee967 lib: sbi: fwft: add support for SBI_FWFT_PTE_AD_HW_UPDATING
c97a1d5 lib: sbi: fwft: add support for SBI_FWFT_MISALIGNED_EXC_DELEG
aa5a859 lib: sbi: add support for firmware features extension
53844c9 lib: sbi: Add support for Svade and Svadu extensions
52dcf35 platform: generic: andes: Add support for RV32 to set up PMA
f09f164 platform: generic: andes: Refine Andes PMA related code
7830e98 lib: serial: fix RX path in litex-uart
62e178a lib: utils/reset: Try initializing all reset devices in dt
3a94a32 sbi: sbi_domain_context: Fix trap context for domain context switching
a73ff04 lib: utils/reset: Fix fdt_reset to search for more dt nodes
b5c984b lib: utils/reset: Skip initialize reset when dt is not enabled
86bbe6c lib: utils/serial: Fix fdt_serial to match more dt nodes
179e00a lib: utils/serial: Skip initialize serial when dt is not enabled
b1c7c75 lib: utils/irqchip: Skip initialize irqchip when dt is not enabled
5e3ad7d lib: utils/timer: Skip initialize timer when dt is not enabled
c5be0e1 lib: utils/ipi: Skip initialize ipi when dt is not enabled
df3db6a lib: utils/fdt: Fix DT property for APLIC delegation
d962db2 lib: utils/gpio: respect flag GPIO_FLAG_ACTIVE_LOW
ae5ef18 lib: sbi: sse: handle missing writable attributes
858754a lib: utils/irqchip: Add sanity checks in imsic_get_data() and imsic_get_target_file()
96f0a2e firmware: Bring back FW_TEXT_START as an optional parameter
e3a30a2 lib: utils/irqchip: Check before initializing imsic
2bed4c1 platform: generic: thead: add Sophgo CV18XX/SG200X series
533067d lib: sbi: Put event after use in sbi_sse_exit() loop
ea9cf6a utils/reset: Add SG2042 hwmon MCU support.
1cb792d lib: sbi: simplify inline function in sbi_dtbr.c
7b37da3 lib: sbi: fix return type of sbi_dbtr_shmem_disabled
e065c3c lib: sbi: Fixed memory permission check in sbi_dbtr_setup_shmem
7f54527 lib: sbi: fix DBTR_SHMEM_MAKE_PHYS for RV64
744f495 lib: sbi: Removal unnecessary check dbtr_thishart_state_ptr
4953bd7 lib: sbi: fix hart_shmem_base
019a8e6 platform: generic: thead: add Canaan Kendryte K230
33e21c9 platform: generic: thead: separate T-Head PMU Errata
2b93ce0 platform: andes: Change all occurrences of andes45 to andes
f68b3ae platform: andes: Rename files with the prefix andes45
17e8291 sbi: sbi_domain_context: Add spinlock for updating domain assigned_harts
1d89a9d lib: sbi: Refine the settings for switching to Virtual Supervisor Mode.
033104d lib: sbi: sse: check handler entry to belong to supervisor mode
bd00765 lib: sbi: sse: use PRV_S instead of hardcoded value for mode
ce3c82c lib: sbi: sse: call enable callback before sending IPI
d528dbf lib: sbi: sse: remove superfluous sbi_list_empty() check
22ff750 lib: sbi: sse: simplify 32bits overflow check
7aa80ea lib: sbi: sse: rename sse_hart_unlock() to sse_enabled_event_unlock()
c21c99d lib: sbi: sse: fix typos, comments and spacing errors
7b1ed96 lib: tests: Add test for spinlocks
7bdf41a lib: tests: Add test for atomic_t
f6243d9 lib: tests: Add test suite init function
d4d2582 firmware: remove FW_TEXT_START
73344d4 lib: utils: check correct value in fdt_node_offset_by_compatible
37e1544 lib: sbi: sse_event_get() may return NULL
68bc031 lib: sbi: Add missing sscrind and sscfg extensions in sbi_hart_ext[]
a7c5c2c Makefile: Remove unnecessary dependencies
268feab Makefile: Respect manual changes to .config
29ecda9 sbi: sbi_domain_context: Check privilege spec version before accessing S-mode CSRs
7862c24 lib: sbi: Wakeup non-coldboot HARTs early in the coldboot path
beb0cd1 lib: sbi: Simplify wait_for_coldboot() implementation
f5375bc platform: generic: allwinner: Optimize current hart scratch access
b94396c lib: utils/timer: Optimize current hart scratch access
5c9a735 include: sbi: Support byteorder macros in assembly
06fc453 lib: sbi: Add SSE support for PMU events
09ad214 lib: sbi: Implement SBI SSE extension
c8cdf01 lib: sbi: Add support for Supervisor Software Events extension
76d7e9b firmware: remove copy-base relocation
5186da6 platform: generic: allwinner: sun20i-d1: Remove duplicated CSR definitions
3b2f89e docs: writing_tests: Make docs correspond the latest changes
f7d0050 lib: sbi: Extend sbi_trap_error() to dump state in a nested trap
5b11f16 lib: sbi: Pass trap context pointer to sbi_ecall_handler()
43d346c lib: sbi: Remove regs parameter from trap irq handling functions
d84e7eb lib: sbi: Remove regs paramter of sbi_irqchip_process()
f414cf9 lib: sbi: Simplify parameters of sbi_illegal_insn_handler()
fea33a9 lib: sbi: Simplify parameters of misaligned and access fault handlers
abea949 lib: sbi: Introduce trap context
60ffc15 include: sbi: Add trap_context pointer in struct sbi_scratch
ebb697a lib: sbi: Remove sbi_trap_exit() and related code
2e85178 lib: sbi: Remove epc from struct sbi_trap_info
86224ec docs/writing_tests: Update tests paths
5c992a1 lib: tests: Move tests to a separate directory
81e3ba7 lib: sbi: call platform load/store emulators
ddf3b64 include: sbi: add emulate_load/store handler to platform ops
4c11265 lib: sbi: abstract out insn decoding to unify mem fault handlers
9221fe5 lib: sbi: change prototype of sbi_misaligned_load/store_handler
a17600c lib: sbi: change prototype of sbi_trap_redirect
2471cf2 include: sbi: rename sbi_misaligned_ldst.h to sbi_trap_ldst.h
c0a6320 lib: sbi: rename sbi_misaligned_ldst.c to sbi_trap_ldst.c
e11025c lib: sbi: Add initial domain context management support
87d8fe7 lib: tests: Add sbi_console test
e5f53fd lib: tests: Add a test for sbi_bitmap
874fcef lib: Add SBIUnit testing macros and functions
b9e4de0 docs: Add documentation about tests and SBIUnit
526b9ce firmware: fw_base.S: fix _reset_regs
8151105 firmware: fw_base.S: Remove _relocate_lottery
187397f firmware: fw_dynamic.S: Remove _bad_dynamic_info
b27b7c6 firmware: fw_base: Simplified setup trap handler
fdf5589 firmware: fw_base.S: Simplify address get
748bef1 lib: sbi_misaligned_ldst: Add handling of C.LHU/C.LH and C.SH
bc36678 platform: andes: Drop andes_pmu_setup()
6bb6b61 lib: sbi: Add support for smcsrind and smcdeleg
322b598 lib: sbi_hsm: Restor hart state to stop when fails to start
96a35db docs/firmware: document new options for jump and payload firmwares
2cff7f3 platform: Apply relocatable address
f056939 firmware: Add relocatable FW_PAYLOAD_FDT_ADDR
7227cdd firmware: Add relocatable FW_JUMP_ADDR and FW_JUMP_FDT_ADDR
741e941 platform: starfive: call starfive_jh7110_inst_init() in pm_reset_init()
3edf044 platform: starfive: return error if needed devices are not present
80ae046 platform: starfive: rename "stf,axp15060-regulator" -> "x-powers,axp15060"
5335340 platform: starfive: remove redundant compatibility check in pmic_ops
4d8569d platform: starfive: get I2C offset address from clocks property
034af1f platform: starfive: correct system clock device tree node
88273fe lib: sbi_pmu: Before using we should ensure PMU init done
46c8c65 docs: move documentation of system suspend test.
8df836d platform: generic: Parse system suspend test from config node.
23e7e48 docs: Add OpenSBI DT configuration guide.
67ce5a7 platform: generic: Add support for specify coldboot harts in DT
9c8b18e firmware: fw_base.S: remove _runtime_offset
4c6b7cb firmware: fw_base.S: Improve loading u32
92e8aff firmware: always create dynsym section
d1dad07 Makefile: check for --exclude-libs
4a76f79 Makefile: don't pass -mstrict-align if not supported
21caaa3 fw_base.S: Fix comment errors
1ec353d lib: sbi: Use mask to check the free bit during trigger allocation
bb90a9e lib: sbi: Print number of debug triggers found
76a2a15 lib: sbi: Implement SBI debug trigger extension
fa87ec9 include: sbi: Add SBI debug trigger extension related defines
97f234f lib: sbi: Introduce the SBI debug triggers extension support
40dac6b lib: sbi: Detect support of debug triggers
2499769 include: sbi: Introduce debug trigger register encodings
20ca19a include: sbi: Add TINFO debug trigger CSR
b752099 include: sbi: Introduce common endianess conversion macro
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240715171521.179517-1-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
Commit b1f1e9dcfa renamed 'riscv,delegate' to 'riscv,delegation' since
it is the correct name as per dt-bindings, and the absence of the
correct name will result in validation fails when dumping the dtb and
using dt-validate.
But this change has a side-effect: every other firmware available that
is AIA capable is using 'riscv,delegate', and it will fault/misbehave if
this property isn't present. The property was added back in QEMU 7.0,
meaning we have 2 years of firmware development using the wrong
property.
Re-introducing 'riscv,delegate' while keeping 'riscv,delegation' allows
older firmwares to keep booting with the 'virt' machine.
'riscv,delegate' is then marked for future deprecation with its use
being discouraged from now on.
Cc: Conor Dooley <conor@kernel.org>
Cc: Anup Patel <apatel@ventanamicro.com>
Fixes: b1f1e9dcfa ("hw/riscv/virt.c: aplic DT: rename prop to 'riscv, delegation'")
Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <20240715090455.145888-1-dbarboza@ventanamicro.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
Both CSRRS and CSRRC always read the addressed CSR and cause any read side
effects regardless of rs1 and rd fields. Note that if rs1 specifies a register
holding a zero value other than x0, the instruction will still attempt to write
the unmodified value back to the CSR and will cause any attendant side effects.
So if CSRRS or CSRRC tries to write a read-only CSR with rs1 which specifies
a register holding a zero value, an illegal instruction exception should be
raised.
Signed-off-by: Yu-Ming Chang <yumin686@andestech.com>
Signed-off-by: Alvin Chang <alvinga@andestech.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-ID: <172100444279.18077.6893072378718059541-0@git.sr.ht>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|