aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2024-04-10hw/virtio: Introduce virtio_bh_new_guarded() helperPhilippe Mathieu-Daudé
Introduce virtio_bh_new_guarded(), similar to qemu_bh_new_guarded() but using the transport memory guard, instead of the device one (there can only be one virtio device per virtio bus). Inspired-by: Gerd Hoffmann <kraxel@redhat.com> Reviewed-by: Gerd Hoffmann <kraxel@redhat.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Message-Id: <20240409105537.18308-2-philmd@linaro.org> (cherry picked from commit ec0504b989ca61e03636384d3602b7bf07ffe4da) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-04-10target/m68k: Map FPU exceptions to FPSR registerKeith Packard
Add helpers for reading/writing the 68881 FPSR register so that changes in floating point exception state can be seen by the application. Call these helpers in pre_load/post_load hooks to synchronize exception state. Signed-off-by: Keith Packard <keithp@keithp.com> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-Id: <20230803035231.429697-1-keithp@keithp.com> Signed-off-by: Richard Henderson <richard.henderson@linaro.org> (cherry picked from commit 5888357942da1fd5a50efb6e4a6af8b1a27a5af8) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-04-10target/sh4: add missing CHECK_NOT_DELAY_SLOTZack Buhman
CHECK_NOT_DELAY_SLOT is correctly applied to the branch-related instructions, but not to the PC-relative mov* instructions. I verified the existence of an illegal slot exception on a SH7091 when any of these instructions are attempted inside a delay slot. This also matches the behavior described in the SH-4 ISA manual. Signed-off-by: Zack Buhman <zack@buhman.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-Id: <20240407150705.5965-1-zack@buhman.org> Signed-off-by: Richard Henderson <richard.henderson@linaro.org> Reviewd-by: Yoshinori Sato <ysato@users.sourceforge.jp> (cherry picked from commit b754cb2dcde26a7bc8a9d17bb6900a0ac0dd38e2) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-04-10target/sh4: Fix mac.w with saturation enabledZack Buhman
The saturation arithmetic logic in helper_macw is not correct. I tested and verified this behavior on a SH7091. Reviewd-by: Yoshinori Sato <ysato@users.sourceforge.jp> Signed-off-by: Zack Buhman <zack@buhman.org> Message-Id: <20240405233802.29128-3-zack@buhman.org> [rth: Reformat helper_macw, add a test case.] Signed-off-by: Richard Henderson <richard.henderson@linaro.org> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> (cherry picked from commit 7227c0cd506eaab5b1d89d15832cac7e05ecb412) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-04-10target/sh4: Fix mac.l with saturation enabledZack Buhman
The saturation arithmetic logic in helper_macl is not correct. I tested and verified this behavior on a SH7091. Signed-off-by: Zack Buhman <zack@buhman.org> Message-Id: <20240404162641.27528-2-zack@buhman.org> [rth: Reformat helper_macl, add a test case.] Signed-off-by: Richard Henderson <richard.henderson@linaro.org> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> (cherry picked from commit c97e8977dcacb3fa8362ee28bcee75ceb01fceaa) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-04-10target/sh4: Merge mach and macl into a unionRichard Henderson
Allow host access to the entire 64-bit accumulator. Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Signed-off-by: Richard Henderson <richard.henderson@linaro.org> (cherry picked from commit 7d95db5e78a24d3315e3112d26909a7262355cb7) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-04-10target/sh4: mac.w: memory accesses are 16-bit wordsZack Buhman
Before this change, executing a code sequence such as: mova tblm,r0 mov r0,r1 mova tbln,r0 clrs clrmac mac.w @r0+,@r1+ mac.w @r0+,@r1+ .align 4 tblm: .word 0x1234 .word 0x5678 tbln: .word 0x9abc .word 0xdefg Does not result in correct behavior: Expected behavior: first macw : macl = 0x1234 * 0x9abc + 0x0 mach = 0x0 second macw: macl = 0x5678 * 0xdefg + 0xb00a630 mach = 0x0 Observed behavior (qemu-sh4eb, prior to this commit): first macw : macl = 0x5678 * 0xdefg + 0x0 mach = 0x0 second macw: (unaligned longword memory access, SIGBUS) Various SH-4 ISA manuals also confirm that `mac.w` is a 16-bit word memory access, not a 32-bit longword memory access. Signed-off-by: Zack Buhman <zack@buhman.org> Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Message-Id: <20240402093756.27466-1-zack@buhman.org> Signed-off-by: Richard Henderson <richard.henderson@linaro.org> (cherry picked from commit b0f2f2976b4db05351117b0440b32bf0aac2c5c6) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-04-10linux-user: Fix waitid return of siginfo_t and rusageRichard Henderson
The copy back to siginfo_t should be conditional only on arg3, not the specific values that might have been written. The copy back to rusage was missing entirely. Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2262 Signed-off-by: Richard Henderson <richard.henderson@linaro.org> Tested-by: Alex Fan <alex.fan.q@gmail.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> (cherry picked from commit f0907ff4cae743f1a4ef3d0a55a047029eed06ff) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-04-10tcg/optimize: Do not attempt to constant fold neg_vecRichard Henderson
Split out the tail of fold_neg to fold_neg_no_const so that we can avoid attempting to constant fold vector negate. Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2150 Signed-off-by: Richard Henderson <richard.henderson@linaro.org> (cherry picked from commit e25fe886b89a396bae5847520b70c148587d490a) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-04-09virtio-snd: rewrite invalid tx/rx message handlingManos Pitsidianakis
The current handling of invalid virtqueue elements inside the TX/RX virt queue handlers is wrong. They are added in a per-stream invalid queue to be processed after the handler is done examining each message, but the invalid message might not be specifying any stream_id; which means it's invalid to add it to any stream->invalid queue since stream could be NULL at this point. This commit moves the invalid queue to the VirtIOSound struct which guarantees there will always be a valid temporary place to store them inside the tx/rx handlers. The queue will be emptied before the handler returns, so the queue must be empty at any other point of the device's lifetime. Signed-off-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org> Message-Id: <virtio-snd-rewrite-invalid-tx-rx-message-handling-v1.manos.pitsidianakis@linaro.org> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> (cherry picked from commit 731655f87f319fd06f27282c6cafbc2467ac8045) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-04-09virtio-snd: Enhance error handling for invalid transfersZheyu Ma
This patch improves error handling in virtio_snd_handle_tx_xfer() and virtio_snd_handle_rx_xfer() in the VirtIO sound driver. Previously, 'goto' statements were used for error paths, leading to unnecessary processing and potential null pointer dereferences. Now, 'continue' is used to skip the rest of the current loop iteration for errors such as message size discrepancies or null streams, reducing crash risks. ASAN log illustrating the issue addressed: ERROR: AddressSanitizer: SEGV on unknown address 0x0000000000b4 #0 0x57cea39967b8 in qemu_mutex_lock_impl qemu/util/qemu-thread-posix.c:92:5 #1 0x57cea128c462 in qemu_mutex_lock qemu/include/qemu/thread.h:122:5 #2 0x57cea128d72f in qemu_lockable_lock qemu/include/qemu/lockable.h:95:5 #3 0x57cea128c294 in qemu_lockable_auto_lock qemu/include/qemu/lockable.h:105:5 #4 0x57cea1285eb2 in virtio_snd_handle_rx_xfer qemu/hw/audio/virtio-snd.c:1026:9 #5 0x57cea2caebbc in virtio_queue_notify_vq qemu/hw/virtio/virtio.c:2268:9 #6 0x57cea2cae412 in virtio_queue_host_notifier_read qemu/hw/virtio/virtio.c:3671:9 #7 0x57cea39822f1 in aio_dispatch_handler qemu/util/aio-posix.c:372:9 #8 0x57cea3979385 in aio_dispatch_handlers qemu/util/aio-posix.c:414:20 #9 0x57cea3978eb1 in aio_dispatch qemu/util/aio-posix.c:424:5 #10 0x57cea3a1eede in aio_ctx_dispatch qemu/util/async.c:360:5 Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Reviewed-by: Manos Pitsidianakis <manos.pitsidianakis@linaro.org> Message-Id: <20240322110827.568412-1-zheyuma97@gmail.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> (cherry picked from commit a45f09935c88ae352a5ec120418a8b2b36ec1daa) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-04-09vdpa-dev: Fix the issue of device status not updating when configuration ↵lyx634449800
interruption is triggered The set_config callback function vhost_vdpa_device_get_config in vdpa-dev does not fetch the current device status from the hardware device, causing the guest os to not receive the latest device status information. The hardware updates the config status of the vdpa device and then notifies the os. The guest os receives an interrupt notification, triggering a get_config access in the kernel, which then enters qemu internally. Ultimately, the vhost_vdpa_device_get_config function of vdpa-dev is called One scenario encountered is when the device needs to bring down the vdpa net device. After modifying the status field of virtio_net_config in the hardware, it sends an interrupt notification. However, the guest os always receives the STATUS field as VIRTIO_NET_S_LINK_UP. Signed-off-by: Yuxue Liu <yuxue.liu@jaguarmicro.com> Acked-by: Jason Wang <jasowang@redhat.com> Message-Id: <20240408020003.1979-1-yuxue.liu@jaguarmicro.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> (cherry picked from commit 6ae72f609a21cfc56bf655cd4bcded5d07691ce7) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-04-09hw/virtio: Fix packed virtqueue flush used_idxWafer
In the event of writing many chains of descriptors, the device must write just the id of the last buffer in the descriptor chain, skip forward the number of descriptors in the chain, and then repeat the operations for the rest of chains. Current QEMU code writes all the buffer ids consecutively, and then skips all the buffers altogether. This is a bug, and can be reproduced with a VirtIONet device with _F_MRG_RXBUB and without _F_INDIRECT_DESC: If a virtio-net device has the VIRTIO_NET_F_MRG_RXBUF feature but not the VIRTIO_RING_F_INDIRECT_DESC feature, 'VirtIONetQueue->rx_vq' will use the merge feature to store data in multiple 'elems'. The 'num_buffers' in the virtio header indicates how many elements are merged. If the value of 'num_buffers' is greater than 1, all the merged elements will be filled into the descriptor ring. The 'idx' of the elements should be the value of 'vq->used_idx' plus 'ndescs'. Fixes: 86044b24e8 ("virtio: basic packed virtqueue support") Acked-by: Eugenio Pérez <eperezma@redhat.com> Signed-off-by: Wafer <wafer@jaguarmicro.com> Message-Id: <20240407015451.5228-2-wafer@jaguarmicro.com> Reviewed-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Michael S. Tsirkin <mst@redhat.com> (cherry picked from commit 2d9a31b3c27311eca1682cb2c076d7a300441960) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-04-09target/arm: Use correct SecuritySpace for AArch64 AT ops at EL3Peter Maydell
When we do an AT address translation operation, the page table walk is supposed to be performed in the context of the EL we're doing the walk for, so for instance an AT S1E2R walk is done for EL2. In the pseudocode an EL is passed to AArch64.AT(), which calls SecurityStateAtEL() to find the security state that we should be doing the walk with. In ats_write64() we get this wrong, instead using the current security space always. This is fine for AT operations performed from EL1 and EL2, because there the current security state and the security state for the lower EL are the same. But for AT operations performed from EL3, the current security state is always either Secure or Root, whereas we want to use the security state defined by SCR_EL3.{NS,NSE} for the walk. This affects not just guests using FEAT_RME but also ones where EL3 is Secure state and the EL3 code is trying to do an AT for a NonSecure EL2 or EL1. Use arm_security_space_below_el3() to get the SecuritySpace to pass to do_ats_write() for all AT operations except the AT S1E3* operations. Cc: qemu-stable@nongnu.org Fixes: e1ee56ec2383 ("target/arm: Pass security space rather than flag for AT instructions") Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2250 Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20240405180232.3570066-1-peter.maydell@linaro.org (cherry picked from commit 19b254e86a900dc5ee332e3ac0baf9c521301abf) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-04-09migration/postcopy: ensure preempt channel is ready before loading statesWei Wang
Before loading the guest states, ensure that the preempt channel has been ready to use, as some of the states (e.g. via virtio_load) might trigger page faults that will be handled through the preempt channel. So yield to the main thread in the case that the channel create event hasn't been dispatched. Cc: qemu-stable <qemu-stable@nongnu.org> Fixes: 9358982744 ("migration: Send requested page directly in rp-return thread") Originally-by: Lei Wang <lei4.wang@intel.com> Link: https://lore.kernel.org/all/9aa5d1be-7801-40dd-83fd-f7e041ced249@intel.com/T/ Signed-off-by: Lei Wang <lei4.wang@intel.com> Signed-off-by: Wei Wang <wei.w.wang@intel.com> Link: https://lore.kernel.org/r/20240405034056.23933-1-wei.w.wang@intel.com [peterx: add a todo section, add Fixes and copy stable for 8.0+] Signed-off-by: Peter Xu <peterx@redhat.com> (cherry picked from commit 7afbdada7effbc2b97281bfbce0c6df351a3cf88) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-04-09block/virtio-blk: Fix memory leak from virtio_blk_zone_reportZheyu Ma
This modification ensures that in scenarios where the buffer size is insufficient for a zone report, the function will now properly set an error status and proceed to a cleanup label, instead of merely returning. The following ASAN log reveals it: ==1767400==ERROR: LeakSanitizer: detected memory leaks Direct leak of 312 byte(s) in 1 object(s) allocated from: #0 0x64ac7b3280cd in malloc llvm/compiler-rt/lib/asan/asan_malloc_linux.cpp:129:3 #1 0x735b02fb9738 in g_malloc (/lib/x86_64-linux-gnu/libglib-2.0.so.0+0x5e738) #2 0x64ac7d23be96 in virtqueue_split_pop hw/virtio/virtio.c:1612:12 #3 0x64ac7d23728a in virtqueue_pop hw/virtio/virtio.c:1783:16 #4 0x64ac7cfcaacd in virtio_blk_get_request hw/block/virtio-blk.c:228:27 #5 0x64ac7cfca7c7 in virtio_blk_handle_vq hw/block/virtio-blk.c:1123:23 #6 0x64ac7cfecb95 in virtio_blk_handle_output hw/block/virtio-blk.c:1157:5 Signed-off-by: Zheyu Ma <zheyuma97@gmail.com> Message-id: 20240404120040.1951466-1-zheyuma97@gmail.com Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com> (cherry picked from commit bbdf9023665f409113cb07b463732861af63fb47) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-04-03hw/net/virtio-net: fix qemu set used ring flag even vhost startedYajun Wu
When vhost-user or vhost-kernel is handling virtio net datapath, QEMU should not touch used ring. But with vhost-user socket reconnect scenario, in a very rare case (has pending kick event). VRING_USED_F_NO_NOTIFY is set by QEMU in following code path: #0 virtio_queue_split_set_notification (vq=0x7ff5f4c920a8, enable=0) at ../hw/virtio/virtio.c:511 #1 0x0000559d6dbf033b in virtio_queue_set_notification (vq=0x7ff5f4c920a8, enable=0) at ../hw/virtio/virtio.c:576 #2 0x0000559d6dbbbdbc in virtio_net_handle_tx_bh (vdev=0x559d703a6aa0, vq=0x7ff5f4c920a8) at ../hw/net/virtio-net.c:2801 #3 0x0000559d6dbf4791 in virtio_queue_notify_vq (vq=0x7ff5f4c920a8) at ../hw/virtio/virtio.c:2248 #4 0x0000559d6dbf79da in virtio_queue_host_notifier_read (n=0x7ff5f4c9211c) at ../hw/virtio/virtio.c:3525 #5 0x0000559d6d9a5814 in virtio_bus_cleanup_host_notifier (bus=0x559d703a6a20, n=1) at ../hw/virtio/virtio-bus.c:321 #6 0x0000559d6dbf83c9 in virtio_device_stop_ioeventfd_impl (vdev=0x559d703a6aa0) at ../hw/virtio/virtio.c:3774 #7 0x0000559d6d9a55c8 in virtio_bus_stop_ioeventfd (bus=0x559d703a6a20) at ../hw/virtio/virtio-bus.c:259 #8 0x0000559d6d9a53e8 in virtio_bus_grab_ioeventfd (bus=0x559d703a6a20) at ../hw/virtio/virtio-bus.c:199 #9 0x0000559d6dbf841c in virtio_device_grab_ioeventfd (vdev=0x559d703a6aa0) at ../hw/virtio/virtio.c:3783 #10 0x0000559d6d9bde18 in vhost_dev_enable_notifiers (hdev=0x559d707edd70, vdev=0x559d703a6aa0) at ../hw/virtio/vhost.c:1592 #11 0x0000559d6d89a0b8 in vhost_net_start_one (net=0x559d707edd70, dev=0x559d703a6aa0) at ../hw/net/vhost_net.c:266 #12 0x0000559d6d89a6df in vhost_net_start (dev=0x559d703a6aa0, ncs=0x559d7048d890, data_queue_pairs=31, cvq=0) at ../hw/net/vhost_net.c:412 #13 0x0000559d6dbb5b89 in virtio_net_vhost_status (n=0x559d703a6aa0, status=15 '\017') at ../hw/net/virtio-net.c:311 #14 0x0000559d6dbb5e34 in virtio_net_set_status (vdev=0x559d703a6aa0, status=15 '\017') at ../hw/net/virtio-net.c:392 #15 0x0000559d6dbb60d8 in virtio_net_set_link_status (nc=0x559d7048d890) at ../hw/net/virtio-net.c:455 #16 0x0000559d6da64863 in qmp_set_link (name=0x559d6f0b83d0 "hostnet1", up=true, errp=0x7ffdd76569f0) at ../net/net.c:1459 #17 0x0000559d6da7226e in net_vhost_user_event (opaque=0x559d6f0b83d0, event=CHR_EVENT_OPENED) at ../net/vhost-user.c:301 #18 0x0000559d6ddc7f63 in chr_be_event (s=0x559d6f2ffea0, event=CHR_EVENT_OPENED) at ../chardev/char.c:62 #19 0x0000559d6ddc7fdc in qemu_chr_be_event (s=0x559d6f2ffea0, event=CHR_EVENT_OPENED) at ../chardev/char.c:82 This issue causes guest kernel stop kicking device and traffic stop. Add vhost_started check in virtio_net_handle_tx_bh to fix this wrong VRING_USED_F_NO_NOTIFY set. Signed-off-by: Yajun Wu <yajunw@nvidia.com> Reviewed-by: Jiri Pirko <jiri@nvidia.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Message-ID: <20240402045109.97729-1-yajunw@nvidia.com> [PMD: Use unlikely()] Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org> (cherry picked from commit 4c54f5bc8e1d38f15cc35b6a6932d8fbe219c692) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-04-02target/arm: take HSTR traps of cp15 accesses to EL2, not EL1Peter Maydell
The HSTR_EL2 register allows the hypervisor to trap AArch32 EL1 and EL0 accesses to cp15 registers. We incorrectly implemented this so they trap to EL1 when we detect the need for a HSTR trap at code generation time. (The check in access_check_cp_reg() which we do at runtime to catch traps from EL0 is correctly routing them to EL2.) Use the correct target EL when generating the code to take the trap. Cc: qemu-stable@nongnu.org Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2226 Fixes: 049edada5e93df ("target/arm: Make HSTR_EL2 traps take priority over UNDEF-at-EL1") Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20240325133116.2075362-1-peter.maydell@linaro.org (cherry picked from commit fbe5ac5671a9cfcc7f4aee9a5fac7720eea08876) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-04-02hw/intc/arm_gicv3: ICC_HPPIR* return SPURIOUS if int group is disabledPeter Maydell
If the group of the highest priority pending interrupt is disabled via ICC_IGRPEN*, the ICC_HPPIR* registers should return INTID_SPURIOUS, not the interrupt ID. (See the GIC architecture specification pseudocode functions ICC_HPPIR1_EL1[] and HighestPriorityPendingInterrupt().) Make HPPIR reads honour the group disable, the way we already do when determining whether to preempt in icc_hppi_can_preempt(). Cc: qemu-stable@nongnu.org Signed-off-by: Peter Maydell <peter.maydell@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-id: 20240328153333.2522667-1-peter.maydell@linaro.org (cherry picked from commit 44e25fbc1900c99c91a44e532c5bd680bc403459) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-04-01gitlab-ci/cirrus: switch from 'master' to 'latest'Michael Tokarev
Commit ab72522797 "gitlab: switch from 'stable' to 'latest' docker container tags" switched most tags to 'latest' but missed cirrus image. Fix this now. Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2256 Signed-off-by: Michael Tokarev <mjt@tls.msk.ru> Message-id: 20240401051633.2780456-1-mjt@tls.msk.ru Signed-off-by: Peter Maydell <peter.maydell@linaro.org> (cherry picked from commit 1d2f2b35bc86b7a13dc3009a3c5031220aa0b7de)
2024-04-01migration/postcopy: Ensure postcopy_start() sets errp if it failsAvihai Horon
There are several places where postcopy_start() fails without setting errp. This can cause a null pointer de-reference, as in case of error, the caller of postcopy_start() copies/prints the error set in errp. Fix it by setting errp in all of postcopy_start() error paths. Cc: qemu-stable <qemu-stable@nongnu.org> Fixes: 908927db28ea ("migration: Update error description whenever migration fails") Signed-off-by: Avihai Horon <avihaih@nvidia.com> Reviewed-by: Cédric Le Goater <clg@redhat.com> Reviewed-by: Peter Xu <peterx@redhat.com> Link: https://lore.kernel.org/r/20240328140252.16756-3-avihaih@nvidia.com Signed-off-by: Peter Xu <peterx@redhat.com> (cherry picked from commit d0ad271a7613459bd0a3397c8071a4ad06f3f7eb) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-04-01target/hppa: Clear psw_n for BE on use_nullify_skip pathRichard Henderson
Along this path we have already skipped the insn to be nullified, so the subsequent insn should be executed. Cc: qemu-stable@nongnu.org Reported-by: Sven Schnelle <svens@stackframe.org> Tested-by: Sven Schnelle <svens@stackframe.org> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Signed-off-by: Richard Henderson <richard.henderson@linaro.org> (cherry picked from commit 4a3aa11e1fb25c28c24a43fd2835c429b00a463d) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-31tcg/optimize: Fix sign_mask for logical right-shiftRichard Henderson
The 'sign' computation is attempting to locate the sign bit that has been repeated, so that we can test if that bit is known zero. That computation can be zero if there are no known sign repetitions. Cc: qemu-stable@nongnu.org Fixes: 93a967fbb57 ("tcg/optimize: Propagate sign info for shifting") Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2248 Signed-off-by: Richard Henderson <richard.henderson@linaro.org> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> (cherry picked from commit 2911e9b95f3bb03783ae5ca3e2494dc3b44a9161) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-31hw/net/net_tx_pkt: Fix virtio header without checksum offloadingAkihiko Odaki
It is incorrect to have the VIRTIO_NET_HDR_F_NEEDS_CSUM set when checksum offloading is disabled so clear the bit. TCP/UDP checksum is usually offloaded when the peer requires virtio headers because they can instruct the peer to compute checksum. However, igb disables TX checksum offloading when a VF is enabled whether the peer requires virtio headers because a transmitted packet can be routed to it and it expects the packet has a proper checksum. Therefore, it is necessary to have a correct virtio header even when checksum offloading is disabled. A real TCP/UDP checksum will be computed and saved in the buffer when checksum offloading is disabled. The virtio specification requires to set the packet checksum stored in the buffer to the TCP/UDP pseudo header when the VIRTIO_NET_HDR_F_NEEDS_CSUM bit is set so the bit must be cleared in that case. Fixes: ffbd2dbd8e64 ("e1000e: Perform software segmentation for loopback") Buglink: https://issues.redhat.com/browse/RHEL-23067 Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com> (cherry picked from commit 89a8de364b51db8107d2a210314431885ac52238) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-31virtio-net: Fix vhost virtqueue notifiers for RSSAkihiko Odaki
virtio_net_guest_notifier_pending() and virtio_net_guest_notifier_mask() checked VIRTIO_NET_F_MQ to know there are multiple queues, but VIRTIO_NET_F_RSS also enables multiple queues. Refer to n->multiqueue, which is set to true either of VIRTIO_NET_F_MQ or VIRTIO_NET_F_RSS is enabled. Fixes: 68b0a6395f36 ("virtio-net: align ctrl_vq index for non-mq guest for vhost_vdpa") Signed-off-by: Akihiko Odaki <akihiko.odaki@daynix.com> Signed-off-by: Jason Wang <jasowang@redhat.com> (cherry picked from commit 1c188fc8cbffc5f05cc616cab4e1372fb6e6f11f) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-27target/riscv/kvm: fix timebase-frequency when using KVM accelerationYong-Xuan Wang
The timebase-frequency of guest OS should be the same with host machine. The timebase-frequency value in DTS should be got from hypervisor when using KVM acceleration. Signed-off-by: Yong-Xuan Wang <yongxuan.wang@sifive.com> Message-ID: <20240314061510.9800-1-yongxuan.wang@sifive.com> Reviewed-by: Andrew Jones <ajones@ventanamicro.com> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Signed-off-by: Alistair Francis <alistair.francis@wdc.com> (cherry picked from commit 385e575cd5ab2436c123e4b7f8c9b383a64c0dbe) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru> (Mjt: context fix due to missing other changes in this area in 8.2.x)
2024-03-27target/riscv: Fix mode in riscv_tlb_fillIrina Ryapolova
Need to convert mmu_idx to privilege mode for PMP function. Signed-off-by: Irina Ryapolova <irina.ryapolova@syntacore.com> Fixes: b297129ae1 ("target/riscv: propagate PMP permission to TLB page") Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Reviewed-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com> Message-ID: <20240320172828.23965-1-irina.ryapolova@syntacore.com> Signed-off-by: Alistair Francis <alistair.francis@wdc.com> (cherry picked from commit e06adebb08325c39e4c9b652139426c10f021abb) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-27target/riscv: rvv: Remove the dependency of Zvfbfmin to ZfbfminMax Chou
According to the Zvfbfmin definition in the RISC-V BF16 extensions spec, the Zvfbfmin extension only requires either the V extension or the Zve32f extension. Signed-off-by: Max Chou <max.chou@sifive.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Message-ID: <20240321170929.1162507-1-max.chou@sifive.com> Signed-off-by: Alistair Francis <alistair.francis@wdc.com> (cherry picked from commit c9b07fe14d3525cd3f2fc01f46eeb3d4ed7c3603) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-27hw/intc: Update APLIC IDC after claiming iforce registerFrank Chang
Currently, QEMU only sets the iforce register to 0 and returns early when claiming the iforce register. However, this may leave mip.meip remains at 1 if a spurious external interrupt triggered by iforce register is the only pending interrupt to be claimed, and the interrupt cannot be lowered as expected. This commit fixes this issue by calling riscv_aplic_idc_update() to update the IDC status after the iforce register is claimed. Signed-off-by: Frank Chang <frank.chang@sifive.com> Reviewed-by: Jim Shu <jim.shu@sifive.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Message-ID: <20240321104951.12104-1-frank.chang@sifive.com> Signed-off-by: Alistair Francis <alistair.francis@wdc.com> (cherry picked from commit 078189b327ae5c5727b51ec714d9663b1d0ca3df) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-27target/riscv/vector_helper.c: optimize loops in ldst helpersDaniel Henrique Barboza
Change the for loops in ldst helpers to do a single increment in the counter, and assign it env->vstart, to avoid re-reading from vstart every time. Suggested-by: Richard Henderson <richard.henderson@linaro.org> Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-ID: <20240314175704.478276-11-dbarboza@ventanamicro.com> Signed-off-by: Alistair Francis <alistair.francis@wdc.com> (cherry picked from commit 0a11629c915f61df798919db51a18ffe4649cb65) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-27target/riscv/vector_helpers: do early exit when vstart >= vlDaniel Henrique Barboza
We're going to make changes that will required each helper to be responsible for the 'vstart' management, i.e. we will relieve the 'vstart < vl' assumption that helpers have today. Helpers are usually able to deal with vstart >= vl, i.e. doing nothing aside from setting vstart = 0 at the end, but the tail update functions will update the tail regardless of vstart being valid or not. Unifying the tail update process in a single function that would handle the vstart >= vl case isn't trivial (see [1] for more info). This patch takes a blunt approach: do an early exit in every single vector helper if vstart >= vl, unless the helper is guarded with vstart_eq_zero in the translation. For those cases the helper is ready to deal with cases where vl might be zero, i.e. throwing exceptions based on it like vcpop_m() and first_m(). Helpers that weren't changed: - vcpop_m(), vfirst_m(), vmsetm(), GEN_VEXT_VIOTA_M(): these are guarded directly with vstart_eq_zero; - GEN_VEXT_VCOMPRESS_VM(): guarded with vcompress_vm_check() that checks vstart_eq_zero; - GEN_VEXT_RED(): guarded with either reduction_check() or reduction_widen_check(), both check vstart_eq_zero; - GEN_VEXT_FRED(): guarded with either freduction_check() or freduction_widen_check(), both check vstart_eq_zero. Another exception is vext_ldst_whole(), who operates on effective vector length regardless of the current settings in vtype and vl. [1] https://lore.kernel.org/qemu-riscv/1590234b-0291-432a-a0fa-c5a6876097bc@linux.alibaba.com/ Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com> Acked-by: Alistair Francis <alistair.francis@wdc.com> Message-ID: <20240314175704.478276-7-dbarboza@ventanamicro.com> Signed-off-by: Alistair Francis <alistair.francis@wdc.com> (cherry picked from commit df4252b2ecaf93b601109373a17427d1867046e8) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-27target/riscv: always clear vstart in whole vec move insnsDaniel Henrique Barboza
These insns have 2 paths: we'll either have vstart already cleared if vstart_eq_zero or we'll do a brcond to check if vstart >= maxsz to call the 'vmvr_v' helper. The helper will clear vstart if it executes until the end, or if vstart >= vl. For starters, the check itself is wrong: we're checking vstart >= maxsz, when in fact we should use vstart in bytes, or 'startb' like 'vmvr_v' is calling, to do the comparison. But even after fixing the comparison we'll still need to clear vstart in the end, which isn't happening too. We want to make the helpers responsible to manage vstart, including these corner cases, precisely to avoid these situations: - remove the wrong vstart >= maxsz cond from the translation; - add a 'startb >= maxsz' cond in 'vmvr_v', and clear vstart if that happens. This way we're now sure that vstart is being cleared in the end of the execution, regardless of the path taken. Fixes: f714361ed7 ("target/riscv: rvv-1.0: implement vstart CSR") Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-ID: <20240314175704.478276-5-dbarboza@ventanamicro.com> Signed-off-by: Alistair Francis <alistair.francis@wdc.com> (cherry picked from commit 7e53e3ddf6dff200098e112c5370ab16d2d5dbd1) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-27target/riscv/vector_helper.c: fix 'vmvr_v' memcpy endianessDaniel Henrique Barboza
vmvr_v isn't handling the case where the host might be big endian and the bytes to be copied aren't sequential. Suggested-by: Richard Henderson <richard.henderson@linaro.org> Fixes: f714361ed7 ("target/riscv: rvv-1.0: implement vstart CSR") Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-ID: <20240314175704.478276-4-dbarboza@ventanamicro.com> Signed-off-by: Alistair Francis <alistair.francis@wdc.com> (cherry picked from commit 768e7b329c0be22035da077fe76221dd0a47103b) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-27trans_rvv.c.inc: set vstart = 0 in int scalar move insnsDaniel Henrique Barboza
trans_vmv_x_s, trans_vmv_s_x, trans_vfmv_f_s and trans_vfmv_s_f aren't setting vstart = 0 after execution. This is usually done by a helper in vector_helper.c but these functions don't use helpers. We'll set vstart after any potential 'over' brconds, and that will also mandate a mark_vs_dirty() too. Fixes: dedc53cbc9 ("target/riscv: rvv-1.0: integer scalar move instructions") Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Message-ID: <20240314175704.478276-3-dbarboza@ventanamicro.com> Signed-off-by: Alistair Francis <alistair.francis@wdc.com> (cherry picked from commit 0848f7c18ef50de9f955e7eeb4363d92766a41bf) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-27target/riscv/vector_helper.c: set vstart = 0 in GEN_VEXT_VSLIDEUP_VX()Daniel Henrique Barboza
The helper isn't setting env->vstart = 0 after its execution, as it is expected from every vector instruction that completes successfully. Signed-off-by: Daniel Henrique Barboza <dbarboza@ventanamicro.com> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Reviewed-by: Alistair Francis <alistair.francis@wdc.com> Reviewed-by: LIU Zhiwei <zhiwei_liu@linux.alibaba.com> Message-ID: <20240314175704.478276-2-dbarboza@ventanamicro.com> Signed-off-by: Alistair Francis <alistair.francis@wdc.com> (cherry picked from commit d3646e31ce6d1e02e46e6eabdbc2e637c0cbece7) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-27monitor/hmp-cmds-target: Append a space in error message in gpa2hva()Yao Xingtao
In qemu monitor mode, when we use gpa2hva command to print the host virtual address corresponding to a guest physical address, if the gpa is not in RAM, the error message is below: (qemu) gpa2hva 0x750000000 Memory at address 0x750000000is not RAM A space is missed between '0x750000000' and 'is'. Signed-off-by: Yao Xingtao <yaoxt.fnst@fujitsu.com> Fixes: e9628441df ("hmp: gpa2hva and gpa2hpa hostaddr command") Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Reviewed-by: Dr. David Alan Gilbert <dave@treblig.org> Message-ID: <20240319021610.2423844-1-ruansy.fnst@fujitsu.com> Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org> (cherry picked from commit a158c63b3ba120f1656e4dd815d186c623fb5ef6) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-27hw/scsi/scsi-generic: Fix io_timeout property not applyingLorenz Brun
The io_timeout property, introduced in c9b6609 (part of 6.0) is silently overwritten by the hardcoded default value of 30 seconds (DEFAULT_IO_TIMEOUT) in scsi_generic_realize because that function is being called after the properties have already been applied. The property definition already has a default value which is applied correctly when no value is explicitly set, so we can just remove the code which overrides the io_timeout completely. This has been tested by stracing SG_IO operations with the io_timeout property set and unset and now sets the timeout field in the ioctl request to the proper value. Fixes: c9b6609b69facad ("scsi: make io_timeout configurable") Signed-off-by: Lorenz Brun <lorenz@brun.one> Message-ID: <20240315145831.2531695-1-lorenz@brun.one> Reviewed-by: Alex Bennée <alex.bennee@linaro.org> Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org> (cherry picked from commit 7c7a9f578e4fb1adff7ac8d9acaaaedb87474e76) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-27target/i386/tcg: Enable page walking from MMIO memoryGregory Price
CXL emulation of interleave requires read and write hooks due to requirement for subpage granularity. The Linux kernel stack now enables using this memory as conventional memory in a separate NUMA node. If a process is deliberately forced to run from that node $ numactl --membind=1 ls the page table walk on i386 fails. Useful part of backtrace: (cpu=cpu@entry=0x555556fd9000, fmt=fmt@entry=0x555555fe3378 "cpu_io_recompile: could not find TB for pc=%p") at ../../cpu-target.c:359 (retaddr=0, addr=19595792376, attrs=..., xlat=<optimized out>, cpu=0x555556fd9000, out_offset=<synthetic pointer>) at ../../accel/tcg/cputlb.c:1339 (cpu=0x555556fd9000, full=0x7fffee0d96e0, ret_be=ret_be@entry=0, addr=19595792376, size=size@entry=8, mmu_idx=4, type=MMU_DATA_LOAD, ra=0) at ../../accel/tcg/cputlb.c:2030 (cpu=cpu@entry=0x555556fd9000, p=p@entry=0x7ffff56fddc0, mmu_idx=<optimized out>, type=type@entry=MMU_DATA_LOAD, memop=<optimized out>, ra=ra@entry=0) at ../../accel/tcg/cputlb.c:2356 (cpu=cpu@entry=0x555556fd9000, addr=addr@entry=19595792376, oi=oi@entry=52, ra=ra@entry=0, access_type=access_type@entry=MMU_DATA_LOAD) at ../../accel/tcg/cputlb.c:2439 at ../../accel/tcg/ldst_common.c.inc:301 at ../../target/i386/tcg/sysemu/excp_helper.c:173 (err=0x7ffff56fdf80, out=0x7ffff56fdf70, mmu_idx=0, access_type=MMU_INST_FETCH, addr=18446744072116178925, env=0x555556fdb7c0) at ../../target/i386/tcg/sysemu/excp_helper.c:578 (cs=0x555556fd9000, addr=18446744072116178925, size=<optimized out>, access_type=MMU_INST_FETCH, mmu_idx=0, probe=<optimized out>, retaddr=0) at ../../target/i386/tcg/sysemu/excp_helper.c:604 Avoid this by plumbing the address all the way down from x86_cpu_tlb_fill() where is available as retaddr to the actual accessors which provide it to probe_access_full() which already handles MMIO accesses. Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2180 Resolves: https://gitlab.com/qemu-project/qemu/-/issues/2220 Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Suggested-by: Peter Maydell <peter.maydell@linaro.org> Signed-off-by: Gregory Price <gregory.price@memverge.com> Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Message-ID: <20240307155304.31241-2-Jonathan.Cameron@huawei.com> Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org> (cherry picked from commit 9dab7bbb017d11b64c52239fa4e2f910a6a004f2) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-27iotests: add test for stream job with an unaligned prefetch readFiona Ebner
Previously, bdrv_pad_request() could not deal with a NULL qiov when a read needed to be aligned. During prefetch, a stream job will pass a NULL qiov. Add a test case to cover this scenario. By accident, also covers a previous race during shutdown, where block graph changes during iteration in bdrv_flush_all() could lead to unreferencing the wrong block driver state and an assertion failure later. Signed-off-by: Fiona Ebner <f.ebner@proxmox.com> Message-ID: <20240322095009.346989-5-f.ebner@proxmox.com> Reviewed-by: Kevin Wolf <kwolf@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com> (cherry picked from commit 12d7b3bbd3333cededd3b695501d8d247239d769) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-27block-backend: fix edge case in bdrv_next_cleanup() where BDS associated to ↵Fiona Ebner
BB changes Same rationale as for commit "block-backend: fix edge case in bdrv_next() where BDS associated to BB changes". The block graph might change between the bdrv_next() call and the bdrv_next_cleanup() call, so it could be that the associated BDS is not the same that was referenced previously anymore. Instead, rely on bdrv_next() to set it->bs to the BDS it referenced and unreference that one in any case. Signed-off-by: Fiona Ebner <f.ebner@proxmox.com> Message-ID: <20240322095009.346989-4-f.ebner@proxmox.com> Reviewed-by: Kevin Wolf <kwolf@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com> (cherry picked from commit bac09b093ebbb79e6a7444c7b979c32ca5540132) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-27block-backend: fix edge case in bdrv_next() where BDS associated to BB changesFiona Ebner
The old_bs variable in bdrv_next() is currently determined by looking at the old block backend. However, if the block graph changes before the next bdrv_next() call, it might be that the associated BDS is not the same that was referenced previously. In that case, the wrong BDS is unreferenced, leading to an assertion failure later: > bdrv_unref: Assertion `bs->refcnt > 0' failed. In particular, this can happen in the context of bdrv_flush_all(), when polling for bdrv_co_flush() in the generated co-wrapper leads to a graph change (for example with a stream block job [0]). A racy reproducer: > #!/bin/bash > rm -f /tmp/backing.qcow2 > rm -f /tmp/top.qcow2 > ./qemu-img create /tmp/backing.qcow2 -f qcow2 64M > ./qemu-io -c "write -P42 0x0 0x1" /tmp/backing.qcow2 > ./qemu-img create /tmp/top.qcow2 -f qcow2 64M -b /tmp/backing.qcow2 -F qcow2 > ./qemu-system-x86_64 --qmp stdio \ > --blockdev qcow2,node-name=node0,file.driver=file,file.filename=/tmp/top.qcow2 \ > <<EOF > {"execute": "qmp_capabilities"} > {"execute": "block-stream", "arguments": { "job-id": "stream0", "device": "node0" } } > {"execute": "quit"} > EOF [0]: > #0 bdrv_replace_child_tran (child=..., new_bs=..., tran=...) > #1 bdrv_replace_node_noperm (from=..., to=..., auto_skip=..., tran=..., errp=...) > #2 bdrv_replace_node_common (from=..., to=..., auto_skip=..., detach_subchain=..., errp=...) > #3 bdrv_drop_filter (bs=..., errp=...) > #4 bdrv_cor_filter_drop (cor_filter_bs=...) > #5 stream_prepare (job=...) > #6 job_prepare_locked (job=...) > #7 job_txn_apply_locked (fn=..., job=...) > #8 job_do_finalize_locked (job=...) > #9 job_exit (opaque=...) > #10 aio_bh_poll (ctx=...) > #11 aio_poll (ctx=..., blocking=...) > #12 bdrv_poll_co (s=...) > #13 bdrv_flush (bs=...) > #14 bdrv_flush_all () > #15 do_vm_stop (state=..., send_stop=...) > #16 vm_shutdown () Signed-off-by: Fiona Ebner <f.ebner@proxmox.com> Message-ID: <20240322095009.346989-3-f.ebner@proxmox.com> Reviewed-by: Kevin Wolf <kwolf@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com> (cherry picked from commit f6d38c9f6dae6fce99dcaf6ca16a1fe5b5e19c4c) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-27block/io: accept NULL qiov in bdrv_pad_requestStefan Reiter
Some operations, e.g. block-stream, perform reads while discarding the results (only copy-on-read matters). In this case, they will pass NULL as the target QEMUIOVector, which will however trip bdrv_pad_request, since it wants to extend its passed vector. In particular, this is the case for the blk_co_preadv() call in stream_populate(). If there is no qiov, no operation can be done with it, but the bytes and offset still need to be updated, so the subsequent aligned read will actually be aligned and not run into an assertion failure. In particular, this can happen when the request alignment of the top node is larger than the allocated part of the bottom node, in which case padding becomes necessary. For example: > ./qemu-img create /tmp/backing.qcow2 -f qcow2 64M -o cluster_size=32768 > ./qemu-io -c "write -P42 0x0 0x1" /tmp/backing.qcow2 > ./qemu-img create /tmp/top.qcow2 -f qcow2 64M -b /tmp/backing.qcow2 -F qcow2 > ./qemu-system-x86_64 --qmp stdio \ > --blockdev qcow2,node-name=node0,file.driver=file,file.filename=/tmp/top.qcow2 \ > <<EOF > {"execute": "qmp_capabilities"} > {"execute": "blockdev-add", "arguments": { "driver": "compress", "file": "node0", "node-name": "node1" } } > {"execute": "block-stream", "arguments": { "job-id": "stream0", "device": "node1" } } > EOF Originally-by: Stefan Reiter <s.reiter@proxmox.com> Signed-off-by: Thomas Lamprecht <t.lamprecht@proxmox.com> [FE: do update bytes and offset in any case add reproducer to commit message] Signed-off-by: Fiona Ebner <f.ebner@proxmox.com> Message-ID: <20240322095009.346989-2-f.ebner@proxmox.com> Reviewed-by: Kevin Wolf <kwolf@redhat.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com> (cherry picked from commit 3f934817c82c2f1bf1c238f8d1065a3be10a3c9e) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-27vdpa-dev: Fix initialisation order to restore VDUSE compatibilityKevin Wolf
VDUSE requires that virtqueues are first enabled before the DRIVER_OK status flag is set; with the current API of the kernel module, it is impossible to enable the opposite order in our block export code because userspace is not notified when a virtqueue is enabled. This requirement also mathces the normal initialisation order as done by the generic vhost code in QEMU. However, commit 6c482547 accidentally changed the order for vdpa-dev and broke access to VDUSE devices with this. This changes vdpa-dev to use the normal order again and use the standard vhost callback .vhost_set_vring_enable for this. VDUSE devices can be used with vdpa-dev again after this fix. vhost_net intentionally avoided enabling the vrings for vdpa and does this manually later while it does enable them for other vhost backends. Reflect this in the vhost_net code and return early for vdpa, so that the behaviour doesn't change for this device. Cc: qemu-stable@nongnu.org Fixes: 6c4825476a43 ('vdpa: move vhost_vdpa_set_vring_ready to the caller') Signed-off-by: Kevin Wolf <kwolf@redhat.com> Message-ID: <20240315155949.86066-1-kwolf@redhat.com> Reviewed-by: Eugenio Pérez <eperezma@redhat.com> Reviewed-by: Stefano Garzarella <sgarzare@redhat.com> Signed-off-by: Kevin Wolf <kwolf@redhat.com> (cherry picked from commit 2c66de61f88dc9620a32239f7dd61524a57f66b0) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-25target/s390x: Use mutable temporary value for op_tsIdo Plat
Otherwise TCG would assume the register that holds t1 would be constant and reuse whenever it needs the value within it. Cc: qemu-stable@nongnu.org Fixes: f1ea739bd598 ("target/s390x: Use tcg_constant_* in local contexts") Reviewed-by: Ilya Leoshkevich <iii@linux.ibm.com> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> [iii: Adjust a newline and capitalization, add tags] Signed-off-by: Ido Plat <ido.plat@ibm.com> Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com> Reviewed-by: David Hildenbrand <david@redhat.com> Message-ID: <20240318202722.20675-1-iii@linux.ibm.com> Signed-off-by: Thomas Huth <thuth@redhat.com> (cherry picked from commit 272fba9779af0bb1c29cd30302fc1e31c59274d0) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-25target/loongarch: Fix qemu-system-loongarch64 assert failed with the option ↵Song Gao
'-d int' qemu-system-loongarch64 assert failed with the option '-d int', the helper_idle() raise an exception EXCP_HLT, but the exception name is undefined. Signed-off-by: Song Gao <gaosong@loongson.cn> Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org> Message-Id: <20240321123606.1704900-1-gaosong@loongson.cn> (cherry picked from commit 1590154ee4376819a8c6ee61e849ebf4a4e7cd02) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-22docs/conf.py: Remove usage of distutilsThomas Huth
The macOS jobs in our CI recently started failing, complaining that the distutils module is not available anymore. And indeed, according to https://peps.python.org/pep-0632/ it's been deprecated since a while and now likely got removed in recent Python versions. Fortunately, we only use it for a version check via LooseVersion here which we don't really need anymore - according to Repology.org, these are the versions of sphinx-rtd-theme that are currently used by the various distros: centos_stream_8: 0.3.1 centos_stream_9: 0.5.1 fedora_38: 1.1.1 fedora_39: 1.2.2 freebsd: 1.0.0 haikuports_master: 1.2.1 openbsd: 1.2.2 opensuse_leap_15_5: 0.5.1 pkgsrc_current: 2.0.0 debian_11: 0.5.1 debian_12: 1.2.0 ubuntu_20_04: 0.4.3 ubuntu_22_04: 1.0.0 ubuntu_24_04: 2.0.0 So except for CentOS 8, all distros are using a newer version of sphinx-rtd-theme, and for CentOS 8 we don't support compiling with the Sphinx of the distro anymore anyway, since it's based on the Python 3.6 interpreter there. For compiling on CentOS 8, you have to use the alternative Python 3.8 interpreter which comes without Sphinx, so that needs the Sphinx installed via pip in the venv instead, and that is using a newer version, too, according to our pythondeps.toml file. Thus we can simply drop the version check now to get rid of the distutils dependency here. Signed-off-by: Thomas Huth <thuth@redhat.com> Reviewed-by: Michael Tokarev <mjt@tls.msk.ru> Message-id: 20240304130403.129543-1-thuth@redhat.com Signed-off-by: Peter Maydell <peter.maydell@linaro.org> (cherry picked from commit eb844330bd36ebdd4959053da08069d1e5d49119) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-22target/loongarch: Fix qemu-loongarch64 hang when executing 'll.d $t0, $t0, 0'Song Gao
On gen_ll, if a->imm is zero, make_address_x return src1, but the load to destination may clobber src1. We use a new destination to fix this problem. Fixes: c5af6628f4be (target/loongarch: Extract make_address_i() helper) Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Suggested-by: Richard Henderson <richard.henderson@linaro.org> Signed-off-by: Song Gao <gaosong@loongson.cn> Message-Id: <20240320013955.1561311-1-gaosong@loongson.cn> (cherry picked from commit 77642f92c0b71a105aba2a4d03bc62328eae703b) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-22target/hppa: fix do_stdby_e()Sven Schnelle
stdby,e,m was writing data from the wrong half of the register into memory for cases 0-3. Fixes: 25460fc5a71 ("target/hppa: Implement STDBY") Signed-off-by: Sven Schnelle <svens@stackframe.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Message-Id: <20240319161921.487080-7-svens@stackframe.org> Signed-off-by: Richard Henderson <richard.henderson@linaro.org> (cherry picked from commit 518d2f4300e5c50a3e6416fd46e58373781a5267) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-22target/hppa: mask privilege bits in mfiaSven Schnelle
mfia should return only the iaoq bits without privilege bits. Fixes: 98a9cb792c8 ("target-hppa: Implement system and memory-management insns") Signed-off-by: Sven Schnelle <svens@stackframe.org> Reviewed-by: Richard Henderson <richard.henderson@linaro.org> Reviewed-by: Helge Deller <deller@gmx.de> Message-Id: <20240319161921.487080-6-svens@stackframe.org> Signed-off-by: Richard Henderson <richard.henderson@linaro.org> (cherry picked from commit b5e0b3a53c983c4a9620a44a6a557b389e589218) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
2024-03-22target/hppa: exit tb on flush cache instructionsSven Schnelle
When the guest modifies the tb it is currently executing from, it executes a fic instruction. Exit the tb on such instruction, otherwise we might execute stale code. Signed-off-by: Sven Schnelle <svens@stackframe.org> Message-Id: <20240319161921.487080-5-svens@stackframe.org> Signed-off-by: Richard Henderson <richard.henderson@linaro.org> (cherry picked from commit ad1fdacd1b936557514dd72c2079a80be0c2dfb4) Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
generated by cgit v1.2.3 (git 2.26.2) at 2025-01-20 07:01:43 +0000