| Age | Commit message (Collapse) | Author |
|---|
|
The kernel booting specification for an AArch32 kernel requires that
it is booted in Hyp mode if available; otherwise the kernel can't
enable KVM. We were incorrectly leaving the kernel in SVC mode.
If we're booting an AArch32 kernel in the Nonsecure state and Hyp
mode is available, start in it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180820153020.21478-7-peter.maydell@linaro.org
|
|
On 32-bit exception entry, CPSR.J must always be set to 0
(see v7A Arm ARM DDI0406C.c B1.8.5). CPSR.IL must also
be cleared on 32-bit exception entry (see v8A Arm ARM
DDI0487C.a G1.10).
Clear these bits. (This fixes a bug which will never be noticed
by non-buggy guests.)
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180820153020.21478-6-peter.maydell@linaro.org
|
|
Implement the necessary support code for taking exceptions
to Hyp mode in AArch32.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180820153020.21478-5-peter.maydell@linaro.org
|
|
Factor out the code which changes the CPU state so as to
actually take an exception to AArch32. We're going to want
to use this for handling exception entry to Hyp mode.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180820153020.21478-4-peter.maydell@linaro.org
|
|
The AArch32 HCR and HCR2 registers alias HCR_EL2
bits [31:0] and [63:32]; implement them.
Since HCR2 exists in ARMv8 but not ARMv7, we need new
regdef arrays for "we have EL3, not EL2, we're ARMv8"
and "we have EL2, we're ARMv8" to hold the definitions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180820153020.21478-3-peter.maydell@linaro.org
|
|
The v8 AArch32 HACTLR2 register maps to bits [63:32] of ACTLR_EL2.
We implement ACTLR_EL2 as RAZ/WI, so make HACTLR2 also RAZ/WI.
(We put the regdef next to ACTLR_EL2 as a reminder in case we
ever make ACTLR_EL2 something other than RAZ/WI).
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@xilinx.com>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180820153020.21478-2-peter.maydell@linaro.org
|
|
Add a "virtualization" property to the vexpress-a15 board,
controlling presence of EL2. As with EL3, we default to
enabling it, but the user can disable it if they have an
older guest which can't cope with it being present.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180821132811.17675-10-peter.maydell@linaro.org
|
|
Don't request that the arm_load_kernel() code should boot in secure
state if the CPU doesn't have a secure state. Currently this
doesn't make a difference because the boot.c code only examines
the secure_boot flag in code guarded by an ARM_FEATURE_EL3 check,
but upcoming changes for supporting booting into Hyp mode will
change that.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180821132811.17675-9-peter.maydell@linaro.org
|
|
For the A15MPCore internal peripheral object, we handle GIC
security extensions support by checking whether the CPUs
have EL3 enabled; if so then we enable it also on the GIC.
Handle the virtualization extensions in the same way: if the
CPU has EL2 then enable it on the GIC and wire up the
virtualization-specific memory regions and the maintenance
interrupt.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180821132811.17675-8-peter.maydell@linaro.org
|
|
Connect the VIRQ and VFIQ lines from the GIC to the CPU;
these exist always for both CPU and GIC whether the
virtualization extensions are enabled or not, so we
can just unconditionally connect them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180821132811.17675-7-peter.maydell@linaro.org
|
|
Connect the VIRQ and VFIQ lines from the GIC to the CPU;
these exist always for both CPU and GIC whether the
virtualization extensions are enabled or not, so we
can just unconditionally connect them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180821132811.17675-6-peter.maydell@linaro.org
|
|
Connect the VIRQ and VFIQ lines from the GIC to the CPU;
these exist always for both CPU and GIC whether the
virtualization extensions are enabled or not, so we
can just unconditionally connect them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180821132811.17675-5-peter.maydell@linaro.org
|
|
Connect the VIRQ and VFIQ lines from the GIC to the CPU;
these exist always for both CPU and GIC whether the
virtualization extensions are enabled or not, so we
can just unconditionally connect them.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180821132811.17675-4-peter.maydell@linaro.org
|
|
Reduce the size of the per-cpu GICH memory regions from 0x1000
to 0x200. The registers only cover 0x200 bytes, and the Cortex-A15
wants to map them at a spacing of 0x200 bytes apart. Having the
region be too large interferes with mapping them like that, so
reduce it.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Luc Michel <luc.michel@greensocs.com>
Message-id: 20180821132811.17675-3-peter.maydell@linaro.org
|
|
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814002653.12828-5-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814002653.12828-4-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814002653.12828-3-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Message-id: 20180814002653.12828-2-richard.henderson@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The VM tests currently have a timeout of 2 minutes for trying
to connect to ssh. Since the guest VM has to boot from cold
to the point of accepting inbound ssh during this time, if the
host machine is heavily loaded it can spuriously time out.
Increase the timeout from 2 to 5 minutes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Acked-by: Fam Zheng <famz@redhat.com>
Message-id: 20180823112153.15279-1-peter.maydell@linaro.org
|
|
* x86 TCG fixes for 64-bit call gates (Andrew)
* qumu-guest-agent freeze-hook tweak (Christian)
* pm_smbus improvements (Corey)
* Move validation to pre_plug for pc-dimm (David)
* Fix memory leaks (Eduardo, Marc-André)
* synchronization profiler (Emilio)
* Convert the CPU list to RCU (Emilio)
* LSI support for PPR Extended Message (George)
* vhost-scsi support for protection information (Greg)
* Mark mptsas as a storage device in the help (Guenter)
* checkpatch tweak cherry-picked from Linux (me)
* Typos, cleanups and dead-code removal (Julia, Marc-André)
* qemu-pr-helper support for old libmultipath (Murilo)
* Annotate fallthroughs (me)
* MemoryRegionOps cleanup (me, Peter)
* Make s390 qtests independent from libqos, which doesn't actually support it (me)
* Make cpu_get_ticks independent from BQL (me)
* Introspection fixes (Thomas)
* Support QEMU_MODULE_DIR environment variable (ryang)
# gpg: Signature made Thu 23 Aug 2018 17:46:30 BST
# gpg: using RSA key BFFBD25F78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (69 commits)
KVM: cleanup unnecessary #ifdef KVM_CAP_...
target/i386: update MPX flags when CPL changes
i2c: pm_smbus: Add the ability to force block transfer enable
i2c: pm_smbus: Don't delay host status register busy bit when interrupts are enabled
i2c: pm_smbus: Add interrupt handling
i2c: pm_smbus: Add block transfer capability
i2c: pm_smbus: Make the I2C block read command read-only
i2c: pm_smbus: Fix the semantics of block I2C transfers
i2c: pm_smbus: Clean up some style issues
pc-dimm: assign and verify the "addr" property during pre_plug
pc: drop memory region alignment check for 0
util/oslib-win32: indicate alignment for qemu_anon_ram_alloc()
pc-dimm: assign and verify the "slot" property during pre_plug
ipmi: Use proper struct reference for BT vmstate
vhost-scsi: expose 't10_pi' property for VIRTIO_SCSI_F_T10_PI
vhost-scsi: unify vhost-scsi get_features implementations
vhost-user-scsi: move host_features into VHostSCSICommon
cpus: allow cpu_get_ticks out of BQL
cpus: protect TimerState writes with a spinlock
seqlock: add QemuLockable support
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The capability macros are always defined, since they come from kernel
headers that are copied into the QEMU tree. Remove the unnecessary #ifdefs.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The PIIX4 hardware has block transfer buffer always enabled in
the hardware, but the i801 does not. Add a parameter to pm_smbus_init
to force on the block transfer so the PIIX4 handler can enable this
by default, as it was disabled by default before.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-9-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
enabled
Change 880b1ffe6ec2f0ae "smbus: do not immediately complete commands"
changed pm_smbus to delay setting the host busy bit until the status
register was read, to work around a bug in AMIBIOS. Unfortunately,
when interrupts are enabled, the status register will never get read
and the processing will never happen.
Modify the code to only delay setting the host busy bit if interrupts
are not enabled.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Hervé Poussineau <hpoussin@reactos.org>
Cc: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <1534796770-10295-8-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Add the necessary code so that interrupts actually work from
the pm_smbus device.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-7-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
There was no block transfer code in pm_smbus.c, and it is needed
for some devices. So add it.
This adds both byte-by-byte block transfers and buffered block
transfers.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-5-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
It did have write capability, but the manual says the behavior
with write enabled is undefined. So just set an error in this
case.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-4-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The I2C block transfer commands was not implemented correctly, it
read a length byte and such like it was an smbus transfer.
So fix the smbus_read_block() and smbus_write_block() functions
so they can properly handle I2C transfers, and normal SMBus
transfers (for upcoming changes). Pass in a transfer size and
a bool to know whether to use the size byte (like SMBus) or use
the length given (like I2C).
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-3-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Fix some spacing issues, remove extraneous comments, add some
defines instead of hard-coding numbers.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <1534796770-10295-2-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
We can assign and verify the address before realizing and trying to plug.
reading/writing the address property should never fail for DIMMs, so let's
reduce error handling a bit by using &error_abort. Getting access to the
memory region now might however fail. So forward errors from
get_memory_region() properly.
As all memory devices should use the alignment of the underlying memory
region for guest physical address asignment, do detection of the
alignment in pc_dimm_pre_plug(), but allow pc.c to overwrite the
alignment for compatibility handling.
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180801133444.11269-5-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
All applicable memory regions always have an alignment > 0. All memory
backends result in file_ram_alloc() or qemu_anon_ram_alloc() getting
called, setting the alignment to > 0.
So a PCDIMM memory region always has an alignment > 0. NVDIMM copy the
alignment of the original memory memory region into the handcrafted memory
region that will be used at this place.
So the check for 0 can be dropped and we can reduce the special
handling.
Dropping this check makes factoring out of alignment handling easier as
compat handling only has to look at pcmc->enforce_aligned_dimm and not
care about the alignment of the memory region.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180801133444.11269-4-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Let's set the alignment just like for the posix variant. This will
implicitly set the alignment of the underlying memory region and
therefore make memory_region_get_alignment(mr) return something > 0 for
all memory backends applicable to PCDIMM/NVDIMM.
The allocation granularity is ususally 64k, while the page size is 4k.
The documentation of VirtualAlloc is not really comprehensible in case
only MEM_COMMIT is specified without an address. We'll detect the actual
values and then go for the bigger one. The expection is, that it will
always be 64k aligned. (The assumption is that MEM_COMMIT does an
implicit MEM_RESERVE, so the address will always be aligned to the
allocation granularity. And the allocation granularity is always bigger
than the page size).
This will allow us to drop special handling in pc.c for
memory_region_get_alignment(mr) == 0, as we can then assume that it is
always set (and AFAICS >= getpagesize()).
For pc in pc_memory_plug(), under Windows TARGET_PAGE_SIZE == getpagesize(),
therefore alignment of DIMMs will not change, and therefore also not the
guest physical memory layout.
For spapr in spapr_memory_plug(), an alignment of 0 would have been used
until now. As QEMU_ALIGN_UP will crash with the alignment being 0, this
never worked, so we don't have to care about compatibility handling.
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180801133444.11269-3-david@redhat.com>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
We can assign and verify the slot before realizing and trying to plug.
reading/writing the slot property should never fail, so let's reduce
error handling a bit by using &error_abort.
To do this during pre_plug, add and use (x86, ppc) pc_dimm_pre_plug().
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Reviewed-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Eric Auger <eric.auger@redhat.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180801133444.11269-2-david@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The vmstate for isa_ipmi_bt was referencing into the bt structure,
instead create a bt structure separate and use that.
The version 1 of the BT transfer was fairly broken, if a migration
occured during an IPMI operation, it is likely the migration would
be corrupted because I misunderstood the VMSTATE_VBUFFER_UINT32()
handling, I thought it handled transferring the length field,
too. So I just remove support for that. I doubt anyone is using
it at this point.
This also removes the transfer of use_irq, since that should come
from configuration.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Message-Id: <1534798644-13587-1-git-send-email-minyard@acm.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Allow toggling on/off the VIRTIO_SCSI_F_T10_PI feature bit for both
vhost-scsi and vhost-user-scsi devices.
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Message-Id: <20180808195235.5843-4-gedwards@ddn.com>
Reviewed-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Move the enablement of preset host features into the common
vhost_scsi_common_get_features() function. This is in preparation for
having vhost-scsi also make use of host_features.
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Message-Id: <20180808195235.5843-3-gedwards@ddn.com>
Reviewed-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
In preparation for having vhost-scsi also make use of host_features,
move it from struct VHostUserSCSI into struct VHostSCSICommon.
Signed-off-by: Greg Edwards <gedwards@ddn.com>
Message-Id: <20180808195235.5843-2-gedwards@ddn.com>
Reviewed-by: Felipe Franciosi <felipe@nutanix.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Because of cpu_ticks_prev, we cannot use a seqlock. But then the conversion
is even easier. :)
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
In the next patch, we will need to write cpu_ticks_offset from any
thread, even outside the BQL. Currently, it is protected by the BQL
just because cpu_enable_ticks and cpu_disable_ticks happen to hold it,
but the critical sections are well delimited and it's easy to remove
the BQL dependency.
Add a spinlock that matches vm_clock_seqlock, and hold it when writing
to the TimerState. This also lets us fix cpu_update_icount when 64-bit
atomics are not available.
Fields of TiemrState are reordered to avoid padding.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
A shortcut when the seqlock write is protected by a spinlock or any mutex
other than the BQL.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Move the icount->ns computation to cpu_get_icount, and make
cpu_get_icount_locked return the raw value. This makes the
atomic_read__nocheck safe, because it now happens always inside a
seqlock and any torn reads will be retried. qemu_icount_bias and
icount_time_shift also need to be accessed with atomics. At the
same time, however, you don't need atomic_read within the writer,
because no concurrent writes are possible.
The fix to vmstate lets us keep the struct nicely packed.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The current paths for modules are CONFIG_QEMU_MODDIR and paths relative
to the executable. Qemu and its modules can be installed and executed in
paths that are different from these search paths. This change allows
a search path to be specified by environment variable.
An example usage for this is postmarketOS[1]. This is a build environment
for Alpine Linux. It sets up Alpine Linux in a chroot environment.
Alpine's Qemu packages are installed in the chroot. The Alpine Linux Qemu
package is used to test compiled Alpine Linux system images. This way there
isn't a reliance on the which ever version of Qemu the host system / distro
provides.
postmarketOS executes Qemu on host system outside of the chroot
The Qemu module search path needs to point to the location of the
chroot relative to the host system.
e.g.
The root of the Alpine Linux chroot is:
~/.local/var/pmbootstrap/chroot_native/
Alpine's Qemu is installed at
~/.local/var/pmbootstrap/chroot_native/usr/bin/
The Qemu module search path needs to be:
QEMU_MODULE_DIR=~/.local/var/pmbootstrap/chroot_native/usr/lib/qemu/
[1] https://postmarketos.org/
Signed-off-by: ryang <decatf@gmail.com>
Message-Id: <20180704181010.GA918@computer>
Reviewed-by: Daniel P. Berrangé <berrange@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The hook already skips a set of rpm upgrade artifacts.
Do the same with such files that might be created by dpkg.
Fixes: https://bugs.launchpad.net/ubuntu/+source/qemu/+bug/1484990
Signed-off-by: Christian Ehrhardt <christian.ehrhardt@canonical.com>
Message-Id: <1513160272-15921-1-git-send-email-christian.ehrhardt@canonical.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Switch the apic away from using the old_mmio MemoryRegionOps
accessor functions.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20180803101943.23722-1-peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Iterating over the list without using atomics is undefined behaviour,
since the list can be modified concurrently by other threads (e.g.
every time a new thread is created in user-mode).
Fix it by implementing the CPU list as an RCU QTAILQ. This requires
a little bit of extra work to traverse list in reverse order (see
previous patch), but other than that the conversion is trivial.
Signed-off-by: Emilio G. Cota <cota@braap.org>
Message-Id: <20180819091335.22863-12-cota@braap.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This paves the way for implementing the CPU list with an RCU list,
which cannot be traversed in reverse order.
Note that this is the only caller of CPU_FOREACH_REVERSE.
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Message-Id: <20180819091335.22863-11-cota@braap.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Signed-off-by: Emilio G. Cota <cota@braap.org>
Message-Id: <20180819091335.22863-10-cota@braap.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Signed-off-by: Emilio G. Cota <cota@braap.org>
Message-Id: <20180819091335.22863-9-cota@braap.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
So that we can test other implementations.
Signed-off-by: Emilio G. Cota <cota@braap.org>
Message-Id: <20180819091335.22863-8-cota@braap.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Instead of declaring it volatile.
Signed-off-by: Emilio G. Cota <cota@braap.org>
Message-Id: <20180819091335.22863-6-cota@braap.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
