| Age | Commit message (Collapse) | Author |
|---|
|
Basic emulation of the M41T80 serial (I2C) RTC chip. Only getting time
of day is implemented. Setting time and RTC alarm are not supported.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Rewrite to make it closer to how real device works so that guest OS
drivers can access I2C devices. Previously this was only a hack to
allow U-Boot to get past accessing SPD EEPROMs but to support other
I2C devices and allow guests to access them we need to model real
device more properly.
Signed-off-by: BALATON Zoltan <balaton@eik.bme.hu>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
At present the Sam460ex board is activated by the general CONFIG_PPC4XX
option. However that includes the board for both ppc-softmmu and
(deprecated) ppcemb-softmmu builds. As Sam460ex is developed, that would
require adding more things into ppcemb-softmmu, which we don't want to do.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The FPSCR[FI] bit indicates if the last floating point instruction had a result that was rounded. Each consecutive floating point instruction is suppose to set this bit to the correct value. What currently happens is this bit is not set as often as it should be. I have verified that this is the behavior of a real PowerPC 950. This patch fixes that problem by deciding to set this bit after each floating point instruction.
https://www.pdfdrive.net/powerpc-microprocessor-family-the-programming-environments-for-32-e3087633.html
Page 63 in table 2-4 is where the description of this bit can be found.
Signed-off-by: John Arbuckle <programmingkidx@gmail.com>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
The store twin case was stubbed out. For now, implement it only within
a serial context, forcing parallel execution to synchronize. It would
be possible to implement with a cmpxchg loop, if we care, but the loose
alignment requirements (simply no crossing 32-byte boundary) might send
us back to the serial context anyway.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
These cases were stubbed out. For now, implement them only within
a serial context, forcing parallel execution to synchronize. It
would be possible to implement these with cmpxchg loops, if we care.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
These operations were previously unimplemented for ppc.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This avoids the need for gen_check_align entirely.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Move the guts of ST_ATOMIC to a function. Use foo_tl for the operations
instead of foo_i32 or foo_i64 specifically. Use MO_ALIGN instead of an
explicit call to gen_check_align.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Move the guts of LD_ATOMIC to a function. Use foo_tl for the operations
instead of foo_i32 or foo_i64 specifically. Use MO_ALIGN instead of an
explicit call to gen_check_align.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Leave only the minimal amount of code within the LDAR macro,
moving the rest of the code into gen_load_locked. Use MO_ALIGN
and remove the explicit call to gen_check_align.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Leave only the minimal amount of code within the STCX macro,
moving the rest of the code into gen_conditional_store.
Remove the explicit call to gen_check_align; the matching LDAX will
have already checked alignment, and we verify the same address.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Always use the gen_conditional_store implementation that uses
atomic_cmpxchg. Make sure and clear reserve_addr across most
interrupts crossing the cpu_loop.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
When running in a parallel context, we must use a helper in order
to perform the 128-bit atomic operation. When running in a serial
context, do the compare before the store.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Section 1.4 of the Power ISA v3.0B states that this insn is
single-copy atomic. As we cannot (yet) issue 128-bit stores
within TCG, use the generic helpers provided.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Section 1.4 of the Power ISA v3.0B states that both of these
instructions are single-copy atomic. As we cannot (yet) issue
128-bit loads within TCG, use the generic helpers provided.
Since TCG cannot (yet) return a 128-bit value, add a slot within
CPUPPCState for returning the high half of a 128-bit return value.
This solution is preferred to the helper assigning to architectural
registers directly, as it avoids clobbering all TCG live values.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This allows faults from MO_ALIGN to have the same effect
as from gen_check_align.
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
commit d35aefa9ae15 ("ppc/pnv: introduce a new intc_create() operation
to the chip model") changed the object link in the pnv_core_realize()
routine but a return was forgotten in case of error, which can lead to
more problems afterwards (segv)
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Reviewed-by: Greg Kurz <groug@kaod.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
With the previous changes, we can now let the ICS_KVM class inherit
directly from ICS_BASE class and not from the intermediate ICS_SIMPLE.
It makes the class hierarchy much cleaner.
What is left in the top classes is the low level interface to access
the KVM XICS device in ICS_KVM and the XICS emulating handlers in
ICS_SIMPLE.
This should not break migration compatibility.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Just like for the realize handlers, this makes possible to move the
common ICSState code of the reset handlers in the ics-base class.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This makes possible to move the common ICSState code of the realize
handlers in the ics-base class.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This changes the ICP realize and reset handlers in DeviceRealize and
DeviceReset handlers. parent handlers are now called from the
inheriting classes which is a cleaner object pattern.
Signed-off-by: Cédric Le Goater <clg@kaod.org>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
sam460ex (or at least this emulation) does not support the "ibm,cpm" power
management. As a result, Linux crashes when trying to access it. Remove
its device tree node. Also, if/when we boot the Linux kernel directly,
serial port clock frequencies in the device tree file will be unset, and
serial port initialization will fail. Add valid frequency values to
the serial ports to be able to use it. Also set valid values for the other
clock nodes otherwise set by u-boot.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: BALATON Zoltan <balaton@eik.bme.hu>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Commit 84051eb400 "adb: add property to disable direct reg 3 writes" added a
workaround for MacOS 9 incorrectly setting the mouse address during boot of
PMU machines.
Further testing has shown that since fb6649f172 "adb: fix read reg 3 byte
ordering" this can still sometimes happen with the CUDA mac99 machine,
so let's enable this workaround for all New World machines using ADB for now.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
This enables us to apply the same filter in DEBUG_DBDMA_CHANMASK to the
DBDMA command execution debug output.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
|
|
Assorted tlb and tb caching fixes
# gpg: Signature made Mon 02 Jul 2018 17:03:07 BST
# gpg: using RSA key 64DF38E8AF7E215F
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>"
# Primary key fingerprint: 7A48 1E78 868B 4DB6 A85A 05C0 64DF 38E8 AF7E 215F
* remotes/rth/tags/pull-tcg-20180702:
cpu: Assert asidx_from_attrs return value in range
accel/tcg: Avoid caching overwritten tlb entries
accel/tcg: Don't treat invalid TLB entries as needing recheck
accel/tcg: Correct "is this a TLB miss" check in get_page_addr_code()
tcg: Define and use new tlb_hit() and tlb_hit_page() functions
translate-all: fix locking of TBs whose two pages share the same physical page
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
'remotes/kraxel/tags/seabios-1.11.2-20180702-pull-request' into staging
seabios: update to release 1.11.2, add/update configuration.
vgabios: remove (old unused lgpl'ed vgabios).
ramfb,bochs-display: use new vgabios roms.
# gpg: Signature made Mon 02 Jul 2018 16:42:06 BST
# gpg: using RSA key 4CB6D8EED3E87138
# gpg: Good signature from "Gerd Hoffmann (work) <kraxel@redhat.com>"
# gpg: aka "Gerd Hoffmann <gerd@kraxel.org>"
# gpg: aka "Gerd Hoffmann (private) <kraxel@gmail.com>"
# Primary key fingerprint: A032 8CFF B93A 17A7 9901 FE7D 4CB6 D8EE D3E8 7138
* remotes/kraxel/tags/seabios-1.11.2-20180702-pull-request:
ramfb: enable vgabios
bochs-display: enable vgabios
seabios: update bios and vgabios binaries
vgabios: remove submodule and build rules.
seabios: enable ide dma
seabios: add vga configs for bochs-display and ramfb
seabios: update submodule to release 1.11.2
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Add vgabios binary to fw_cfg vgaroms.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Add vgabios binary to pci rom bar.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Adds two new vgabios binaries, for ramfb and bochs-display.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
It's the old, lgpl vgabios implementation.
Was left in as fallback when we switched to seavgabios, so we could
easily switch back in case we see regressions. It's unused since years
now, reportedly doesn't even build, and lacks support for recently (and
not so recently) added display devices.
Zap it.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
QNX reportedly requires this to boot.
Should also speed up booting other guests.
Note: Upstream seabios defaults this to 'n' to due to known problems
on physical hardware (qemu not affected), and wouldn't flip the default
to 'y'. So we adjust our local build config accordingly.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Both bochs-display and ramfb are devices with a simple framebuffer and
no vga emulation or text mode. seavgabios has support for text mode
emulation (at vgabios call level), we are using that to provide some
vga compatibility support for these devices.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
git shortlog rel-1.11.1..rel-1.11.2
-----------------------------------
Gerd Hoffmann (11):
optionrom: enable non-vga display devices
cbvga: factor out cbvga_setup_modes()
qemu: add bochs-display support
cbvga_setup_modes: use real mode number instead of 0x140
cbvga_list_modes: don't list current mode twice
cbvga_set_mode: disable clearmem in windows x86 emulator.
bochs_display_setup: return error on failure
pmm: use tmp zone on oom
vgasrc: add allocate_pmm()
qemu: add qemu ramfb support
cbvga_set_mode: refine clear display logic
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
|
|
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
When installing a TLB entry, remove any cached version of the
same page in the VTLB. If the existing TLB entry matches, do
not copy into the VTLB, but overwrite it.
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
In get_page_addr_code() when we check whether the TLB entry
is marked as TLB_RECHECK, we should not go down that code
path if the TLB entry is not valid at all (ie the TLB_INVALID
bit is set).
Tested-by: Laurent Vivier <laurent@vivier.eu>
Reported-by: Laurent Vivier <laurent@vivier.eu>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20180629161731.16239-1-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
In commit 71b9a45330fe220d1 we changed the condition we use
to determine whether we need to refill the TLB in
get_page_addr_code() to
if (unlikely(env->tlb_table[mmu_idx][index].addr_code !=
(addr & (TARGET_PAGE_MASK | TLB_INVALID_MASK)))) {
This isn't the right check (it will falsely fail if the
input addr happens to have the low bit corresponding to
TLB_INVALID_MASK set, for instance). Replace it with a
use of the new tlb_hit() function, which is the correct test.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20180629162122.19376-3-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
The condition to check whether an address has hit against a particular
TLB entry is not completely trivial. We do this in various places, and
in fact in one place (get_page_addr_code()) we have got the condition
wrong. Abstract it out into new tlb_hit() and tlb_hit_page() inline
functions (one for a known-page-aligned address and one for an
arbitrary address), and use them in all the places where we had the
condition correct.
This is a no-behaviour-change patch; we leave fixing the buggy
code in get_page_addr_code() to a subsequent patch.
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-Id: <20180629162122.19376-2-peter.maydell@linaro.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
Commit 0b5c91f ("translate-all: use per-page locking in !user-mode",
2018-06-15) introduced per-page locking. It assumed that the physical
pages corresponding to a TB (at most two pages) are always distinct,
which is wrong. For instance, an xtensa test provided by Max Filippov
is broken by the commit, since the test maps two virtual pages
to the same physical page:
virt1: 7fff, virt2: 8000
phys1 6000fff, phys2 6000000
Fix it by removing the assumption from page_lock_pair.
If the two physical page addresses are equal, we only lock
the PageDesc once. Note that the two callers of page_lock_pair,
namely page_unlock_tb and tb_link_page, are also updated so that
we do not try to unlock the same PageDesc twice.
Fixes: 0b5c91f74f3c83a36f37740969df8c775c997e69
Reported-by: Max Filippov <jcmvbkbc@gmail.com>
Tested-by: Max Filippov <jcmvbkbc@gmail.com>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Emilio G. Cota <cota@braap.org>
Message-Id: <1529944302-14186-1-git-send-email-cota@braap.org>
Signed-off-by: Richard Henderson <richard.henderson@linaro.org>
|
|
s390x updates:
- add bpb/ppa15 features to default cpu model for z196 and later
- rework TOD handling and fix cpu hotplug under tcg
- various fixes
# gpg: Signature made Mon 02 Jul 2018 12:09:40 BST
# gpg: using RSA key DECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <conny@cornelia-huck.de>"
# gpg: aka "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# gpg: aka "Cornelia Huck <cohuck@kernel.org>"
# gpg: aka "Cornelia Huck <cohuck@redhat.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20180702:
s390x/tcg: fix locking problem with tcg_s390_tod_updated
s390x/kvm: indicate alignment in legacy_s390_alloc()
s390x/kvm: legacy_s390_alloc() only supports one allocation
s390x/tcg: fix CPU hotplug with single-threaded TCG
s390x/tcg: rearm the CKC timer during migration
s390x/tcg: implement SET CLOCK
s390x/tcg: SET CLOCK COMPARATOR can clear CKC interrupts
s390x/tcg: properly implement the TOD
s390x/tcg: drop tod_basetime
s390x/tod: factor out TOD into separate device
s390x/kvm: pass values instead of pointers to kvm_s390_set_clock_*()
s390x/tcg: avoid overflows in time2tod/tod2time
s390x/cpumodel: default enable bpb and ppa15 for z196 and later
loader: Check access size when calling rom_ptr() to avoid crashes
s390/ipl: fix ipl with -no-reboot
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
into staging
Fix move16 instruction disassembly
# gpg: Signature made Mon 02 Jul 2018 11:25:51 BST
# gpg: using RSA key F30C38BD3F2FBE3C
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>"
# gpg: aka "Laurent Vivier <laurent@vivier.eu>"
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>"
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier/tags/m68k-for-3.0-pull-request:
target/m68k: correctly disassemble move16
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Fix the --disable-tcg breakage introduced by 8bca9a03ec60d:
$ configure --disable-tcg
[...]
$ make -C i386-softmmu exec.o
make: Entering directory 'i386-softmmu'
CC exec.o
In file included from source/qemu/exec.c:62:0:
source/qemu/include/exec/ram_addr.h:96:6: error: conflicting types for ‘tb_invalidate_phys_range’
void tb_invalidate_phys_range(ram_addr_t start, ram_addr_t end);
^~~~~~~~~~~~~~~~~~~~~~~~
In file included from source/qemu/exec.c:24:0:
source/qemu/include/exec/exec-all.h:309:6: note: previous declaration of ‘tb_invalidate_phys_range’ was here
void tb_invalidate_phys_range(target_ulong start, target_ulong end);
^~~~~~~~~~~~~~~~~~~~~~~~
source/qemu/exec.c:1043:6: error: conflicting types for ‘tb_invalidate_phys_addr’
void tb_invalidate_phys_addr(AddressSpace *as, hwaddr addr, MemTxAttrs attrs)
^~~~~~~~~~~~~~~~~~~~~~~
In file included from source/qemu/exec.c:24:0:
source/qemu/include/exec/exec-all.h:308:6: note: previous declaration of ‘tb_invalidate_phys_addr’ was here
void tb_invalidate_phys_addr(target_ulong addr);
^~~~~~~~~~~~~~~~~~~~~~~
make: *** [source/qemu/rules.mak:69: exec.o] Error 1
make: Leaving directory 'i386-softmmu'
Tested to build x86_64-softmmu and i386-softmmu targets.
Signed-off-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180629200710.27626-1-f4bug@amsat.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
"move16 %a0@+,%a1@" and "fmovel (cpid=3) %a0@-,%fpcr"
share the same opcode.
To fix that, backport the fix from binutils:
2005-11-10 Andreas Schwab <schwab@suse.de>
* m68k-dis.c (print_insn_m68k): Only match FPU insns with
coprocessor ID 1.
Reported-by: Thomas Huth <huth@tuxfamily.org>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Tested-by: Thomas Huth <huth@tuxfamily.org>
Message-Id: <20180625203559.21370-2-laurent@vivier.eu>
|
|
Doesn't build on 32bit clang. And because we run under qemu mutex
anyway they are not needed.
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Tested-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-id: 20180627111936.31019-1-kraxel@redhat.com
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
tcg_s390_tod_updated() is always called with the iothread being locked
(e.g. from S390TODClass->set() e.g. via HELPER(sck) or on incoming
migration). The helper we call takes the lock itself - bad.
Let's change that by factoring out updating the ckc timer. This now looks
much nicer than having to call a helper from another function.
While touching it we also make sure that env->ckc is updated even if the
new value is -1ULL, for now it would not have been modified in that case.
Reported-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180629170520.13671-1-david@redhat.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
|
|
Let's do this for completeness reason, although we don't support e.g.
PCDIMM/NVDIMM, which would use the alignment for placing the memory
region in guest physical memory. But maybe someday we would want to
support something like this - then we don't forget about this if
allowing multiple allocations in legacy_s390_alloc().
Use the same alignment as we would set in qemu_anon_ram_alloc(). Our
fixed address satisfies this alignment (1MB). This implicitly sets the
alignment of the underlying memory region.
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180628113817.30814-3-david@redhat.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
|
|
We always allocate at a fixed address, a second allocation can therefore
of course never work. We would simply overwrite mappings.
This can e.g. happen in s390_memory_init(), if trying to allocate more
than > 8TB. Let's just bail out, as there is no need for supporting it
(legacy handling for z/VM).
Signed-off-by: David Hildenbrand <david@redhat.com>
Message-Id: <20180628113817.30814-2-david@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
|
