| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Enable vectored interrupt support for the 74Kf CPU, reflecting hardware.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Add the M14K and M14Kc processors from MIPS Technologies that are the
original implementation of the microMIPS ISA. They are dual instruction
set processors, implementing both the microMIPS and the standard MIPSr32
ISA.
These processors correspond to the M4K and 4KEc CPUs respectively,
except with support for the microMIPS instruction set added, support for
the MCU ASE added and two extra interrupt lines, making a total of 8
hardware interrupts plus 2 software interrupts. The remaining parts of
the microarchitecture, in particular the pipeline, stayed unchanged.
The presence of the microMIPS ASE is is reflected in the configuration
added. We currently have no support for the MCU ASE, including in
particular the ACLR, ASET and IRET instructions in either encoding, and
we have no support for the extra interrupt lines, including bits in
CP0.Status and CP0.Cause registers, so these features are not marked,
making our support diverge from real hardware.
Signed-off-by: Sandra Loosemore <sandra@codesourcery.com>
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Make the data type used for the CP0.Config4 and CP0.Config5 registers
and their mask signed, for consistency with the remaining 32-bit CP0
registers, like CP0.Config0, etc.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Add the 5KEc and 5KEf processors from MIPS Technologies that are the
original implementation of the MIPS64r2 ISA.
Silicon for these processors has never been taped out and no soft cores
were released even. They do exist though, a CP0.PRId value has been
assigned and experimental RTLs produced at the time the MIPS64r2 ISA has
been finalized. The settings introduced here faithfully reproduce that
hardware.
As far the implementation goes these processors are the same as the 5Kc
and the 5Kf CPUs respectively, except implementing the MIPS64r2 rather
than the original MIPS64 instruction set. There must have been some
updates to the CP0 architecture as mandated by the ISA, such as the
addition of the EBase register, although I am not sure about the exact
details, no documentation has ever been produced for these processors.
The remaining parts of the microarchitecture, in particular the
pipeline, stayed unchanged. Or to put it another way, the difference
between a 5K and a 5KE CPU corresponds to one between a 4K and a 4KE
CPU, except for the 64-bit rather than 32-bit ISA.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
CP1.FIR is read-only in hardware so gdbstub must respect it. We already
respect it for CTC1 instructions, so do it here too.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
Fix an off-by-one error in `mips_cpu_gdb_write_register' for register
matching how `mips_cpu_gdb_read_register' handles it. This register
slot is a fake anyway, there's nothing in hardware that corresponds to
it.
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com>
Reviewed-by: Leon Alrae <leon.alrae@imgtec.com>
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
|
|
- Migration and linuxboot fixes for 2.2 regressions
- valgrind/KVM support
- small i386 patches
- PCI SD host controller support
- malloc/free cleanups from Markus (x86/scsi)
- IvyBridge model
- XSAVES support for KVM
- initial patches from record/replay
# gpg: Signature made Mon 15 Dec 2014 16:35:08 GMT using RSA key ID 78C7AE83
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>"
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83
* remotes/bonzini/tags/for-upstream: (47 commits)
sdhci: Support SDHCI devices on PCI
sdhci: Define SDHCI PCI ids
sdhci: Add "sysbus" to sdhci QOM types and methods
sdhci: Remove class "virtual" methods
sdhci: Set a default frequency clock
serial: only resample THR interrupt on rising edge of IER.THRI
serial: update LSR on enabling/disabling FIFOs
serial: clean up THRE/TEMT handling
serial: reset thri_pending on IER writes with THRI=0
linuxboot: fix loading old kernels
kvm/apic: fix 2.2->2.1 migration
target-i386: add Ivy Bridge CPU model
target-i386: add f16c and rdrand to Haswell and Broadwell
target-i386: add VME to all CPUs
pc: add 2.3 machine types
i386: do not cross the pages boundaries in replay mode
cpus: make icount warp behave well with respect to stop/cont
timer: introduce new QEMU_CLOCK_VIRTUAL_RT clock
cpu-exec: invalidate nocache translation if they are interrupted
icount: introduce cpu_get_icount_raw
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Support for PCI devices following the "SD Host Controller Simplified
Specification Version 2.00" spec.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Update the sdhci sysbus QOM types and methods so that sysbus is in
their name. This is in preparation for adding PCI versions of these
types and methods.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The SDHCIClass defines a series of class "methods". However, no code
in the QEMU tree overrides these methods or even uses them outside of
sdhci.c.
Remove the virtual methods and replace them with direct calls to the
underlying functions. This simplifies the process of extending the
sdhci code to support PCI devices (which have a different parent
class).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The Linux SDHCI PCI driver will only register the device if there is a
clock frequency set. So, set a default frequency of 52Mhz.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
There is disagreement on whether LSR.THRE should be resampled when
IER.THRI goes from 1 to 1. Bochs only does it if IER.THRI goes from 0
to 1; PCE does it even if IER.THRI is unchanged. But the Windows driver
seems to always go from 1 to 0 and back to 1, so do things in agreement
with Bochs, because the handling of thr_ipending was reported in 2010
(https://lists.gnu.org/archive/html/qemu-devel/2010-03/msg01914.html)
as breaking DR-DOS Plus.
Reported-by: Roy Tam <roytam@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When the transmit FIFO is emptied or enabled, the transmitter
hold register is empty. When it is disabled, it is also emptied and
in addition the previous contents of the transmitter hold register
are discarded. In either case, the THRE bit in LSR must be set and
THRI raised.
When the receive FIFO is emptied or enabled, the data ready and break
bits must be cleared in LSR. Likewise when the receive FIFO is disabled.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
- assert TEMT is cleared before sending a character; we'll get one from
TSR if tsr_retry > 0, from the FIFO or THR otherwise
- assert THRE cleared and FIFO not empty (if enabled) before fetching a
character to send. This effectively reverts dffacd46, but the check
makes no sense and commit f702e62 (serial: change retry logic to avoid
concurrency, 2014-07-11) must have made it unnecessary. The commit
message for f702e62 talks about multiple calls to qemu_chr_fe_add_watch
triggering s->tsr_retry >= MAX_XMIT_RETRY, but other failures were
possible. For example, if you have multiple calls, the subsequent ones
will see s->tsr_retry == 0 and will find THRE and/or TEMT on entry.
- for clarity, raise THRI immediately after the code sets THRE
- check THRE to see if another character has to be sent. This makes
the assertions more obvious and also means TEMT has to be set as soon as
the loop ends. It makes the loop send both TSR and THR if flow-control
happens in non-FIFO mode. Previously, THR would be lost.
- clear TEMT together with THRE even in the non-FIFO case
The last two items are bugfixes, but they were just found by inspection
and do not squash known bugs.
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This is responsible for failure of migration from 2.2 to 2.1, because
thr_ipending is always one in practice.
serial.c is setting thr_ipending unconditionally. However, thr_ipending
is not used at all if THRI=0, and it will be overwritten again the next
time THRE or THRI changes. For that reason, we can set thr_ipending to
zero every time THRI is reset.
There is disagreement on whether LSR.THRE should be resampled when IER.THRI
goes from 1 to 1. This patch does not touch the code, leaving that for
QEMU 2.3+.
This has no semantic change and is enough to fix migration in the common
case where the interrupt is not pending or is reported in IIR. It does not
change the migration format, so 2.2.0 -> 2.1 will remain broken but we
can fix 2.2.1 -> 2.1 without breaking 2.2.1 <-> 2.2.0.
The case that remains broken (the one in which the subsection is strictly
necessary) is when THRE=1, the THRI interrupt has *not* been acknowledged
yet, and a higher-priority interrupt comes. In this case, you need the
subsection to tell the source that the lower-priority THRI interrupt is
pending. The subsection's breakage of migration, in this case, prevents
continuing the VM on the destination with an invalid state.
Cc: qemu-stable@nongnu.org
Reported-by: Igor Mammedov <imammedo@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Old kernels that used high memory only allowed the initrd to be in the
first 896MB of memory. If you load the initrd above, they complain
that "initrd extends beyond end of memory".
In order to fix this, while not breaking machines with small amounts
of memory fixed by cdebec5 (linuxboot: compute initrd loading address,
2014-10-06), we need to distinguish two cases. If pc.c placed the
initrd at end of memory, use the new algorithm based on the e801
memory map. If instead pc.c placed the initrd at the maximum address
specified by the bzImage, leave it there.
The only interesting part is that the low-memory info block is now
loaded very early, in real mode, and thus the 32-bit address has
to be converted into a real mode segment. The initrd address is
also patched in the info block before entering real mode, it is
simpler that way.
This fixes booting the RHEL4.8 32-bit installation image with 1GB
of RAM.
Cc: qemu-stable@nongnu.org
Cc: mst@redhat.com
Cc: jsnow@redhat.com
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The wait_for_sipi field is set back to 1 after an INIT, so it was not
effective to reset it in kvm_apic_realize. Introduce a reset callback
and reset wait_for_sipi there.
Reported-by: Igor Mammedov <imammedo@redhat.com>
Cc: qemu-stable@nongnu.org
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Both were added in Ivy Bridge (for which we do not have a CPU model
yet!).
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
vm86 mode extensions date back to the 486. All models should have
them.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The next patch will differentiate them.
Reviewed-by: Eduardo Habkost <ehabkost@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This patch denies crossing the boundary of the pages in the replay mode,
because it can cause an exception. Do it only when boundary is
crossed by the first instruction in the block.
If current instruction already crossed the bound - it's ok,
because an exception hasn't stopped this code.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This patch makes icount warp use the new QEMU_CLOCK_VIRTUAL_RT clock.
This way, icount's QEMU_CLOCK_VIRTUAL will never count time during which
the virtual machine is stopped.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This patch introduces new QEMU_CLOCK_VIRTUAL_RT clock, which
should be used for icount warping. In the next patch, it
will be used to avoid a huge icount warp when a virtual
machine is stopped for a long time.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
In this case, QEMU might longjmp out of cpu-exec.c and miss the final
cleanup in cpu_exec_nocache. Do this manually through a new compile
flag.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Separate accessing the instruction counter from the compensation for
speed and halting that are introduced by qemu_icount_bias. This
introduces new infrastructure used by the record/replay patches.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This patch sets can_do_io function to allow reading icount
within cpu-exec, but outside TB execution.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Exception index is reset at every entry at every entry into cpu_exec()
function. This may cause missing the exceptions while replaying them.
This patch moves exception_index reset to the locations where they are
processed.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
In icount mode cpu_exec_nocache function is used to execute part of the
existing TB. At the end of cpu_exec_nocache newly created TB is deleted.
Sometimes io_read function needs to recompile current TB and restart TB
lookup and execution. After that tb_find_fast function finds old (bigger)
TB again. This TB cannot be executed (because icount is not big enough)
and cpu_exec_nocache is called again. Such a loop continues over and over.
This patch deletes old TB and avoids finding it in the TB cache.
Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The QEMU block layer has a limit of INT_MAX bytes per transfer.
Expose it in the block limits VPD page for both regular transfers
and WRITE SAME.
Reported-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
g_new(T, n) is neater than g_malloc(sizeof(T) * n). It's also safer,
for two reasons. One, it catches multiplication overflowing size_t.
Two, it returns T * rather than void *, which lets the compiler catch
more type errors.
This commit only touches allocations with size arguments of the form
sizeof(T).
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Coccinelle semantic patch:
@@
expression LHS, SZ;
@@
- LHS = g_malloc(SZ);
- memset(LHS, 0, SZ);
+ LHS = g_malloc0(SZ);
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Fam Zheng <famz@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
g_new(T, n) is neater than g_malloc(sizeof(T) * n). It's also safer,
for two reasons. One, it catches multiplication overflowing size_t.
Two, it returns T * rather than void *, which lets the compiler catch
more type errors.
This commit only touches allocations with size arguments of the form
sizeof(T).
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Coccinelle semantic patch:
@@
expression LHS, SZ;
@@
- LHS = g_malloc(SZ);
- memset(LHS, 0, SZ);
+ LHS = g_malloc0(SZ);
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Signed-off-by: Markus Armbruster <armbru@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Add xsaves related definition, it also adds corresponding part
to kvm_get/put, and vmstate.
Signed-off-by: Wanpeng Li <wanpeng.li@linux.intel.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Use the external qemu-timer API instead.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
These represent xsave-related capabilities of the processor, and KVM may
or may not support them.
Add feature bits so that they are considered by "-cpu ...,enforce", and use
the new feature work instead of calling kvm_arch_get_supported_cpuid.
Bit 3 (XSAVES) is not migratables because it requires saving MSR_IA32_XSS.
Neither KVM nor any commonly available hardware supports it anyway.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Paolo Bonzini reported that Coverity reports an uninitialized pad value.
Let's use a designated initializer for kvm_irq_routing_entry to avoid
this false positive. This is similar to kvm_irqchip_add_msi_route and
other users of kvm_irq_routing_entry.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
struct kvm_fpu contains an alignment padding on s390x. Let's use a
designated initializer to avoid false positives from valgrind/memcheck.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
struct kvm_vcpu_events contains reserved fields. Let's use a
designated initializer to avoid false positives in valgrind.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
struct kvm_msrs contains a pad field. Let's use a designated
initializer on the info part to avoid false positives from
valgrind/memcheck.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
struct kvm_msrs contains padding bytes. Let's use a designated
initializer on the info part to avoid false positives from
valgrind/memcheck. Do the same for generic MSRS, the TSC and
feature control.
We also need to zero out the reserved fields in the entries.
We do this in kvm_msr_entry_set as suggested by Paolo. This
avoids a big memset that a designated initializer on the
full structure would do.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
struct kvm_xcrs contains padding bytes. Let's use a designated
initializer to avoid false positives from valgrind/memcheck.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
struct kvm_pit_state2 contains pad fields. Let's use a designated
initializer to avoid false positives from valgrind/memcheck.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
kvm_clock_data contains pad fields. Let's use a designated
initializer to avoid false positives from valgrind/memcheck.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
