aboutsummaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2014-12-16target-mips: remove excp_names[] from linux-user as it is unusedLeon Alrae
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
2014-12-16disas/mips: disable unused mips16_to_32_reg_map[]Leon Alrae
This array is used by print_mips16_insn_arg() which is guarded by #if 0. Therefore doing the same with the array as it generates clang warnings. Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16disas/mips: remove unused mips_msa_control_names_numeric[32]Leon Alrae
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
2014-12-16target-mips: convert single case switch into if statementLeon Alrae
Signed-off-by: Leon Alrae <leon.alrae@imgtec.com> Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
2014-12-16target-mips: Fix DisasContext's ulri member initializationMaciej W. Rozycki
Set DisasContext's ulri member to 0 or 1 as with other bool members. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Reviewed-by: Leon Alrae <leon.alrae@imgtec.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Use local float status pointer across MSA macrosMaciej W. Rozycki
Reduce line wrapping throughout MSA helper macros by using a local float status pointer rather than referring to the float status through the environment each time. No functional change. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Reviewed-by: Leon Alrae <leon.alrae@imgtec.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Add missing calls to synchronise SoftFloat statusMaciej W. Rozycki
Add missing calls to synchronise the SoftFloat status with the CP1.FSCR: + for the rounding and flush-to-zero modes upon processor reset, + for the flush-to-zero mode on FSCR updates through the GDB stub. Refactor code accordingly and remove the redundant RESTORE_ROUNDING_MODE macro. Signed-off-by: Thomas Schwinge <thomas@codesourcery.com> Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Reviewed-by: Leon Alrae <leon.alrae@imgtec.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16linux-user: Use the 5KEf processor for 64-bit emulationMaciej W. Rozycki
Replace the 20Kc original MIPS64 ISA processor used for 64-bit user emulation with the 5KEf processor that implements the MIPS64r2 ISA, complementing the choice of the 24Kf processor for 32-bit emulation. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Reviewed-by: Leon Alrae <leon.alrae@imgtec.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Also apply the CP0.Status mask to MTTC0Maciej W. Rozycki
Make CP0.Status writes made with the MTTC0 instruction respect this register's mask just like all the other places. Also preserve the current values of masked out bits. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Reviewed-by: Leon Alrae <leon.alrae@imgtec.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: gdbstub: Clean up FPU register handlingMaciej W. Rozycki
Rewrite the FPU register access parts of `mips_cpu_gdb_read_register' and `mips_cpu_gdb_write_register' for consistency between each other. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Reviewed-by: Leon Alrae <leon.alrae@imgtec.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Correct 32-bit address space wrappingMaciej W. Rozycki
Make sure the address space is unconditionally wrapped on 32-bit processors, that is ones that do not implement at least the MIPS III ISA. Also make MIPS16 SAVE and RESTORE instructions use address calculation rather than plain arithmetic operations for stack pointer manipulation so that their semantics for stack accesses follows the architecture specification. That in particular applies to user software run on 64-bit processors with the CP0.Status.UX bit clear where the address space is wrapped to 32 bits. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Reviewed-by: Leon Alrae <leon.alrae@imgtec.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Tighten ISA level checksMaciej W. Rozycki
Tighten ISA level checks down to MIPS II that many of our instructions are missing. Also make sure any 64-bit instruction enables are only applied to 64-bit processors, that is ones that implement at least the MIPS III ISA. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Reviewed-by: Leon Alrae <leon.alrae@imgtec.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Fix CP0.Config3.ISAOnExc write accessesMaciej W. Rozycki
Fix CP0.Config3.ISAOnExc write accesses on microMIPS processors. This bit is mandatory for any processor that implements the microMIPS instruction set. This bit is r/w for processors that implement both the standard MIPS and the microMIPS instruction set. This bit is r/o and hardwired to 1 if only the microMIPS instruction set is implemented. There is no other bit ever writable in CP0.Config3 so defining a corresponding `CP0_Config3_rw_bitmask' member in `CPUMIPSState' is I think an overkill. Therefore make the ability to write the bit rely on the presence of ASE_MICROMIPS set in the instruction flags. The read-only case of the microMIPS instruction set being implemented only can be added when we add support for such a configuration. We do not currently have such support, we have no instruction flag that would control the presence of the standard MIPS instruction set nor any associated code in instruction decoding. This change is needed to boot a microMIPS Linux kernel successfully, otherwise it hangs early on as interrupts are enabled and then the exception handler invoked loops as its first instruction is interpreted in the wrong execution mode and triggers another exception right away. And then over and over again. We already check the current setting of the CP0.Config3.ISAOnExc in `set_hflags_for_handler' to set the ISA bit correctly on the exception handler entry so it is the ability to set it that is missing only. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Reviewed-by: Leon Alrae <leon.alrae@imgtec.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Output CP0.Config2-5 in the register dumpMaciej W. Rozycki
Include CP0.Config2 through CP0.Config5 registers in the register dump produced with the `info registers' monitor command. Align vertically with the registers already output. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Fix the 64-bit case for microMIPS MOVE16 and MOVEPMaciej W. Rozycki
Fix microMIPS MOVE16 and MOVEP instructions on 64-bit processors by using register addition operations. This copies the approach taken with MIPS16 MOVE instructions (I8_MOV32R and I8_MOVR32 opcodes) and follows the observation that OPC_ADDU expands to tcg_gen_mov_tl whenever `rt' is 0 and `rs' is not, therefore copying `rs' to `rd' verbatim. This is not the case with OPC_ADDIU where a sign-extension from bit #31 is made, unless in the uninteresting case of `rs' being 0, losing the upper 32 bits of the value copied for any proper 64-bit values. This also serves as an optimization as one op is produced in generated code rather than two (again, unless `rs' is 0, where it doesn't change anything). Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Reviewed-by: Leon Alrae <leon.alrae@imgtec.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Correct the writes to Status and Cause registers via gdbstubMaciej W. Rozycki
Make writes to CP0.Status and CP0.Cause have the same effect as executing corresponding MTC0 instructions would in Kernel Mode. Also ignore writes in the user emulation mode. Currently for requests from the GDB stub we write all the bits across both registers, ignoring any read-only locations, and do not synchronise the environment to evaluate side effects. We also write these registers in the user emulation mode even though a real kernel presents them as read only. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Correct the handling of writes to CP0.Status for MIPSr6Maciej W. Rozycki
Correct these issues with the handling of CP0.Status for MIPSr6: * only ignore the bit pattern of 0b11 on writes to CP0.Status.KSU, that is for processors that do implement Supervisor Mode, let the bit pattern be written to CP0.Status.UM:R0 freely (of course the value written to read-only CP0.Status.R0 will be discarded anyway); this is in accordance to the relevant architecture specification[1], * check the newly written pattern rather than the current contents of CP0.Status for the KSU bits being 0b11, * use meaningful macro names to refer to CP0.Status bits rather than magic numbers. References: [1] "MIPS Architecture For Programmers, Volume III: MIPS64 / microMIPS64 Privileged Resource Architecture", MIPS Technologies, Inc., Document Number: MD00091, Revision 6.00, March 31, 2014, Table 9.45 "Status Register Field Descriptions", pp. 210-211. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Reviewed-by: Leon Alrae <leon.alrae@imgtec.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Correct MIPS16/microMIPS branch size calculationMaciej W. Rozycki
Correct MIPS16/microMIPS branch size calculation in PC adjustment needed: - to set the value of CP0.ErrorEPC at the entry to the reset exception, - for the purpose of branch reexecution in the context of device I/O. Follow the approach taken in `exception_resume_pc' for ordinary, Debug and NMI exceptions. MIPS16 and microMIPS branches can be 2 or 4 bytes in size and that has to be reflected in calculation. Original MIPS ISA branches, which is where this code originates from, are always 4 bytes long, just as all original MIPS ISA instructions. Signed-off-by: Nathan Froyd <froydnj@codesourcery.com> Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Reviewed-by: Leon Alrae <leon.alrae@imgtec.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Restore the order of helpersMaciej W. Rozycki
Restore the order of helpers that used to be: unary operations (generic, then MIPS-specific), binary operations (generic, then MIPS-specific), compare operations. At one point FMA operations were inserted at a random place in the file, disregarding the preexisting order, and later on even more operations sprinkled across the file. Revert the mess by moving FMA operations to a new ternary class inserted after the binary class and move the misplaced unary and binary operations to where they belong. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Remove unused `FLOAT_OP' macroMaciej W. Rozycki
Remove the `FLOAT_OP' macro, unused since commit b6d96beda3a6cbf20a2d04a609eff78adebd8859 [Use temporary registers for the MIPS FPU emulation.]. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Make `helper_float_cvtw_s' consistent with the remaining helpersMaciej W. Rozycki
Move the call to `update_fcr31' in `helper_float_cvtw_s' after the exception flag check, for consistency with the remaining helpers that do it last too. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Fix formatting in `decode_opc'Maciej W. Rozycki
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Fix formatting in `mips_defs'Maciej W. Rozycki
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Fix formatting in `decode_extended_mips16_opc'Maciej W. Rozycki
Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Enable vectored interrupt support for the 74Kf CPUMaciej W. Rozycki
Enable vectored interrupt support for the 74Kf CPU, reflecting hardware. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Reviewed-by: Leon Alrae <leon.alrae@imgtec.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Add M14K and M14Kc MIPS32r2 microMIPS processorsMaciej W. Rozycki
Add the M14K and M14Kc processors from MIPS Technologies that are the original implementation of the microMIPS ISA. They are dual instruction set processors, implementing both the microMIPS and the standard MIPSr32 ISA. These processors correspond to the M4K and 4KEc CPUs respectively, except with support for the microMIPS instruction set added, support for the MCU ASE added and two extra interrupt lines, making a total of 8 hardware interrupts plus 2 software interrupts. The remaining parts of the microarchitecture, in particular the pipeline, stayed unchanged. The presence of the microMIPS ASE is is reflected in the configuration added. We currently have no support for the MCU ASE, including in particular the ACLR, ASET and IRET instructions in either encoding, and we have no support for the extra interrupt lines, including bits in CP0.Status and CP0.Cause registers, so these features are not marked, making our support diverge from real hardware. Signed-off-by: Sandra Loosemore <sandra@codesourcery.com> Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Reviewed-by: Leon Alrae <leon.alrae@imgtec.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Make CP0.Config4 and CP0.Config5 registers signedMaciej W. Rozycki
Make the data type used for the CP0.Config4 and CP0.Config5 registers and their mask signed, for consistency with the remaining 32-bit CP0 registers, like CP0.Config0, etc. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Reviewed-by: Leon Alrae <leon.alrae@imgtec.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Add 5KEc and 5KEf MIPS64r2 processorsMaciej W. Rozycki
Add the 5KEc and 5KEf processors from MIPS Technologies that are the original implementation of the MIPS64r2 ISA. Silicon for these processors has never been taped out and no soft cores were released even. They do exist though, a CP0.PRId value has been assigned and experimental RTLs produced at the time the MIPS64r2 ISA has been finalized. The settings introduced here faithfully reproduce that hardware. As far the implementation goes these processors are the same as the 5Kc and the 5Kf CPUs respectively, except implementing the MIPS64r2 rather than the original MIPS64 instruction set. There must have been some updates to the CP0 architecture as mandated by the ISA, such as the addition of the EBase register, although I am not sure about the exact details, no documentation has ever been produced for these processors. The remaining parts of the microarchitecture, in particular the pipeline, stayed unchanged. Or to put it another way, the difference between a 5K and a 5KE CPU corresponds to one between a 4K and a 4KE CPU, except for the 64-bit rather than 32-bit ISA. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Make CP1.FIR read-only here tooMaciej W. Rozycki
CP1.FIR is read-only in hardware so gdbstub must respect it. We already respect it for CTC1 instructions, so do it here too. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Reviewed-by: Leon Alrae <leon.alrae@imgtec.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-16target-mips: Correct the handling of register #72 on writesMaciej W. Rozycki
Fix an off-by-one error in `mips_cpu_gdb_write_register' for register matching how `mips_cpu_gdb_read_register' handles it. This register slot is a fake anyway, there's nothing in hardware that corresponds to it. Signed-off-by: Maciej W. Rozycki <macro@codesourcery.com> Reviewed-by: Leon Alrae <leon.alrae@imgtec.com> Signed-off-by: Leon Alrae <leon.alrae@imgtec.com>
2014-12-15Merge remote-tracking branch 'remotes/bonzini/tags/for-upstream' into stagingPeter Maydell
- Migration and linuxboot fixes for 2.2 regressions - valgrind/KVM support - small i386 patches - PCI SD host controller support - malloc/free cleanups from Markus (x86/scsi) - IvyBridge model - XSAVES support for KVM - initial patches from record/replay # gpg: Signature made Mon 15 Dec 2014 16:35:08 GMT using RSA key ID 78C7AE83 # gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" # gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" # gpg: WARNING: This key is not certified with sufficiently trusted signatures! # gpg: It is not certain that the signature belongs to the owner. # Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1 # Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83 * remotes/bonzini/tags/for-upstream: (47 commits) sdhci: Support SDHCI devices on PCI sdhci: Define SDHCI PCI ids sdhci: Add "sysbus" to sdhci QOM types and methods sdhci: Remove class "virtual" methods sdhci: Set a default frequency clock serial: only resample THR interrupt on rising edge of IER.THRI serial: update LSR on enabling/disabling FIFOs serial: clean up THRE/TEMT handling serial: reset thri_pending on IER writes with THRI=0 linuxboot: fix loading old kernels kvm/apic: fix 2.2->2.1 migration target-i386: add Ivy Bridge CPU model target-i386: add f16c and rdrand to Haswell and Broadwell target-i386: add VME to all CPUs pc: add 2.3 machine types i386: do not cross the pages boundaries in replay mode cpus: make icount warp behave well with respect to stop/cont timer: introduce new QEMU_CLOCK_VIRTUAL_RT clock cpu-exec: invalidate nocache translation if they are interrupted icount: introduce cpu_get_icount_raw ... Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
2014-12-15sdhci: Support SDHCI devices on PCIKevin O'Connor
Support for PCI devices following the "SD Host Controller Simplified Specification Version 2.00" spec. Signed-off-by: Kevin O'Connor <kevin@koconnor.net> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-12-15sdhci: Define SDHCI PCI idsKevin O'Connor
Signed-off-by: Kevin O'Connor <kevin@koconnor.net> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-12-15sdhci: Add "sysbus" to sdhci QOM types and methodsKevin O'Connor
Update the sdhci sysbus QOM types and methods so that sysbus is in their name. This is in preparation for adding PCI versions of these types and methods. Signed-off-by: Kevin O'Connor <kevin@koconnor.net> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-12-15sdhci: Remove class "virtual" methodsKevin O'Connor
The SDHCIClass defines a series of class "methods". However, no code in the QEMU tree overrides these methods or even uses them outside of sdhci.c. Remove the virtual methods and replace them with direct calls to the underlying functions. This simplifies the process of extending the sdhci code to support PCI devices (which have a different parent class). Signed-off-by: Kevin O'Connor <kevin@koconnor.net> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-12-15sdhci: Set a default frequency clockKevin O'Connor
The Linux SDHCI PCI driver will only register the device if there is a clock frequency set. So, set a default frequency of 52Mhz. Signed-off-by: Kevin O'Connor <kevin@koconnor.net> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-12-15serial: only resample THR interrupt on rising edge of IER.THRIPaolo Bonzini
There is disagreement on whether LSR.THRE should be resampled when IER.THRI goes from 1 to 1. Bochs only does it if IER.THRI goes from 0 to 1; PCE does it even if IER.THRI is unchanged. But the Windows driver seems to always go from 1 to 0 and back to 1, so do things in agreement with Bochs, because the handling of thr_ipending was reported in 2010 (https://lists.gnu.org/archive/html/qemu-devel/2010-03/msg01914.html) as breaking DR-DOS Plus. Reported-by: Roy Tam <roytam@gmail.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-12-15serial: update LSR on enabling/disabling FIFOsPaolo Bonzini
When the transmit FIFO is emptied or enabled, the transmitter hold register is empty. When it is disabled, it is also emptied and in addition the previous contents of the transmitter hold register are discarded. In either case, the THRE bit in LSR must be set and THRI raised. When the receive FIFO is emptied or enabled, the data ready and break bits must be cleared in LSR. Likewise when the receive FIFO is disabled. Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-12-15serial: clean up THRE/TEMT handlingPaolo Bonzini
- assert TEMT is cleared before sending a character; we'll get one from TSR if tsr_retry > 0, from the FIFO or THR otherwise - assert THRE cleared and FIFO not empty (if enabled) before fetching a character to send. This effectively reverts dffacd46, but the check makes no sense and commit f702e62 (serial: change retry logic to avoid concurrency, 2014-07-11) must have made it unnecessary. The commit message for f702e62 talks about multiple calls to qemu_chr_fe_add_watch triggering s->tsr_retry >= MAX_XMIT_RETRY, but other failures were possible. For example, if you have multiple calls, the subsequent ones will see s->tsr_retry == 0 and will find THRE and/or TEMT on entry. - for clarity, raise THRI immediately after the code sets THRE - check THRE to see if another character has to be sent. This makes the assertions more obvious and also means TEMT has to be set as soon as the loop ends. It makes the loop send both TSR and THR if flow-control happens in non-FIFO mode. Previously, THR would be lost. - clear TEMT together with THRE even in the non-FIFO case The last two items are bugfixes, but they were just found by inspection and do not squash known bugs. Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-12-15serial: reset thri_pending on IER writes with THRI=0Paolo Bonzini
This is responsible for failure of migration from 2.2 to 2.1, because thr_ipending is always one in practice. serial.c is setting thr_ipending unconditionally. However, thr_ipending is not used at all if THRI=0, and it will be overwritten again the next time THRE or THRI changes. For that reason, we can set thr_ipending to zero every time THRI is reset. There is disagreement on whether LSR.THRE should be resampled when IER.THRI goes from 1 to 1. This patch does not touch the code, leaving that for QEMU 2.3+. This has no semantic change and is enough to fix migration in the common case where the interrupt is not pending or is reported in IIR. It does not change the migration format, so 2.2.0 -> 2.1 will remain broken but we can fix 2.2.1 -> 2.1 without breaking 2.2.1 <-> 2.2.0. The case that remains broken (the one in which the subsection is strictly necessary) is when THRE=1, the THRI interrupt has *not* been acknowledged yet, and a higher-priority interrupt comes. In this case, you need the subsection to tell the source that the lower-priority THRI interrupt is pending. The subsection's breakage of migration, in this case, prevents continuing the VM on the destination with an invalid state. Cc: qemu-stable@nongnu.org Reported-by: Igor Mammedov <imammedo@redhat.com> Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-12-15linuxboot: fix loading old kernelsPaolo Bonzini
Old kernels that used high memory only allowed the initrd to be in the first 896MB of memory. If you load the initrd above, they complain that "initrd extends beyond end of memory". In order to fix this, while not breaking machines with small amounts of memory fixed by cdebec5 (linuxboot: compute initrd loading address, 2014-10-06), we need to distinguish two cases. If pc.c placed the initrd at end of memory, use the new algorithm based on the e801 memory map. If instead pc.c placed the initrd at the maximum address specified by the bzImage, leave it there. The only interesting part is that the low-memory info block is now loaded very early, in real mode, and thus the 32-bit address has to be converted into a real mode segment. The initrd address is also patched in the info block before entering real mode, it is simpler that way. This fixes booting the RHEL4.8 32-bit installation image with 1GB of RAM. Cc: qemu-stable@nongnu.org Cc: mst@redhat.com Cc: jsnow@redhat.com Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-12-15kvm/apic: fix 2.2->2.1 migrationPaolo Bonzini
The wait_for_sipi field is set back to 1 after an INIT, so it was not effective to reset it in kvm_apic_realize. Introduce a reset callback and reset wait_for_sipi there. Reported-by: Igor Mammedov <imammedo@redhat.com> Cc: qemu-stable@nongnu.org Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-12-15target-i386: add Ivy Bridge CPU modelPaolo Bonzini
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-12-15target-i386: add f16c and rdrand to Haswell and BroadwellPaolo Bonzini
Both were added in Ivy Bridge (for which we do not have a CPU model yet!). Reviewed-by: Eduardo Habkost <ehabkost@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-12-15target-i386: add VME to all CPUsPaolo Bonzini
vm86 mode extensions date back to the 486. All models should have them. Signed-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Eduardo Habkost <ehabkost@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-12-15pc: add 2.3 machine typesPaolo Bonzini
The next patch will differentiate them. Reviewed-by: Eduardo Habkost <ehabkost@redhat.com> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-12-15i386: do not cross the pages boundaries in replay modePavel Dovgalyuk
This patch denies crossing the boundary of the pages in the replay mode, because it can cause an exception. Do it only when boundary is crossed by the first instruction in the block. If current instruction already crossed the bound - it's ok, because an exception hasn't stopped this code. Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-12-15cpus: make icount warp behave well with respect to stop/contPavel Dovgalyuk
This patch makes icount warp use the new QEMU_CLOCK_VIRTUAL_RT clock. This way, icount's QEMU_CLOCK_VIRTUAL will never count time during which the virtual machine is stopped. Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-12-15timer: introduce new QEMU_CLOCK_VIRTUAL_RT clockPavel Dovgalyuk
This patch introduces new QEMU_CLOCK_VIRTUAL_RT clock, which should be used for icount warping. In the next patch, it will be used to avoid a huge icount warp when a virtual machine is stopped for a long time. Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
2014-12-15cpu-exec: invalidate nocache translation if they are interruptedPavel Dovgalyuk
In this case, QEMU might longjmp out of cpu-exec.c and miss the final cleanup in cpu_exec_nocache. Do this manually through a new compile flag. Signed-off-by: Pavel Dovgalyuk <Pavel.Dovgaluk@ispras.ru> Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
generated by cgit v1.2.3 (git 2.26.2) at 2024-12-28 18:09:39 +0000