| Age | Commit message (Collapse) | Author |
|---|
|
With a vfio assigned device we lay down a base MemoryRegion registered
as an IO region, giving us read & write accessors. If the region
supports mmap, we lay down a higher priority sub-region MemoryRegion
on top of the base layer initialized as a RAM device pointer to the
mmap. Finally, if we have any quirks for the device (ie. address
ranges that need additional virtualization support), we put another IO
sub-region on top of the mmap MemoryRegion. When this is flattened,
we now potentially have sub-page mmap MemoryRegions exposed which
cannot be directly mapped through KVM.
This is as expected, but a subtle detail of this is that we end up
with two different access mechanisms through QEMU. If we disable the
mmap MemoryRegion, we make use of the IO MemoryRegion and service
accesses using pread and pwrite to the vfio device file descriptor.
If the mmap MemoryRegion is enabled and results in one of these
sub-page gaps, QEMU handles the access as RAM, using memcpy to the
mmap. Using either pread/pwrite or the mmap directly should be
correct, but using memcpy causes us problems. I expect that not only
does memcpy not necessarily honor the original width and alignment in
performing a copy, but it potentially also uses processor instructions
not intended for MMIO spaces. It turns out that this has been a
problem for Realtek NIC assignment, which has such a quirk that
creates a sub-page mmap MemoryRegion access.
To resolve this, we disable memory_access_is_direct() for ram_device
regions since QEMU assumes that it can use memcpy for those regions.
Instead we access through MemoryRegionOps, which replaces the memcpy
with simple de-references of standard sizes to the host memory.
With this patch we attempt to provide unrestricted access to the RAM
device, allowing byte through qword access as well as unaligned
access. The assumption here is that accesses initiated by the VM are
driven by a device specific driver, which knows the device
capabilities. If unaligned accesses are not supported by the device,
we don't want them to work in a VM by performing multiple aligned
accesses to compose the unaligned access. A down-side of this
philosophy is that the xp command from the monitor attempts to use
the largest available access weidth, unaware of the underlying
device. Using memcpy had this same restriction, but at least now an
operator can dump individual registers, even if blocks of device
memory may result in access widths beyond the capabilities of a
given device (RTL NICs only support up to dword).
Reported-by: Thorsten Kohfeldt <thorsten.kohfeldt@gmx.de>
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Setting skip_dump on a MemoryRegion allows us to modify one specific
code path, but the restriction we're trying to address encompasses
more than that. If we have a RAM MemoryRegion backed by a physical
device, it not only restricts our ability to dump that region, but
also affects how we should manipulate it. Here we recognize that
MemoryRegions do not change to sometimes allow dumps and other times
not, so we replace setting the skip_dump flag with a new initializer
so that we know exactly the type of region to which we're applying
this behavior.
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Two PCI fixes/improvements for s390x.
# gpg: Signature made Mon 31 Oct 2016 10:09:24 GMT
# gpg: using RSA key 0xDECF6B93C6F02FAF
# gpg: Good signature from "Cornelia Huck <huckc@linux.vnet.ibm.com>"
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>"
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
* remotes/cohuck/tags/s390x-20161031:
s390x/pci: Check memory region dispatching callbacks
s390x/pci: use generic interface to inject interrupt
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
into staging
Migration bits from the COLO project
# gpg: Signature made Sun 30 Oct 2016 10:39:55 GMT
# gpg: using RSA key 0xEB0B4DFC657EF670
# gpg: Good signature from "Amit Shah <amit@amitshah.net>"
# gpg: aka "Amit Shah <amit@kernel.org>"
# gpg: aka "Amit Shah <amitshah@gmx.net>"
# Primary key fingerprint: 48CA 3722 5FE7 F4A8 B337 2735 1E9A 3B5F 8540 83B6
# Subkey fingerprint: CC63 D332 AB8F 4617 4529 6534 EB0B 4DFC 657E F670
* remotes/amit-migration/tags/migration-for-2.8:
MAINTAINERS: Add maintainer for COLO framework related files
configure: Support enable/disable COLO feature
docs: Add documentation for COLO feature
COLO: Implement failover work for secondary VM
COLO: Implement the process of failover for primary VM
COLO: Introduce state to record failover process
COLO: Add 'x-colo-lost-heartbeat' command to trigger failover
COLO: Synchronize PVM's state to SVM periodically
COLO: Add checkpoint-delay parameter for migrate-set-parameters
COLO: Load VMState into QIOChannelBuffer before restore it
COLO: Send PVM state to secondary side when do checkpoint
COLO: Add a new RunState RUN_STATE_COLO
COLO: Introduce checkpointing protocol
COLO: Establish a new communicating path for COLO
migration: Switch to COLO process after finishing loadvm
migration: Enter into COLO mode after migration if COLO is enabled
COLO: migrate COLO related info to secondary node
migration: Introduce capability 'x-colo' to migration
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
into staging
Xen 2016/10/28
# gpg: Signature made Sat 29 Oct 2016 02:03:42 BST
# gpg: using RSA key 0x894F8F4870E1AE90
# gpg: Good signature from "Stefano Stabellini <sstabellini@kernel.org>"
# gpg: aka "Stefano Stabellini <stefano.stabellini@eu.citrix.com>"
# Primary key fingerprint: D04E 33AB A51F 67BA 07D3 0AEA 894F 8F48 70E1 AE90
* remotes/sstabellini/tags/xen-20161028-tag:
xen: Rename xen_be_del_xendev
xen: Rename xen_be_find_xendev
xen: Rename xen_be_evtchn_event
xen: Rename xen_be_send_notify
xen: Rename xen_be_unbind_evtchn
xen: Rename xen_be_printf to xen_pv_printf
xen: Move xenstore cleanup and mkdir functions
xen: Prepare xendev qtail to be shared with frontends
xen: Move evtchn functions to xen_pvdev.c
xen: Move xenstore_update to xen_pvdev.c
xen: Create a new file xen_pvdev.c
xen: Fix coding style warnings
xen: Fix coding style errors
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
staging
trivial patches for 2016-10-28
# gpg: Signature made Fri 28 Oct 2016 16:17:51 BST
# gpg: using RSA key 0x701B4F6B1A693E59
# gpg: Good signature from "Michael Tokarev <mjt@tls.msk.ru>"
# gpg: aka "Michael Tokarev <mjt@corpit.ru>"
# gpg: aka "Michael Tokarev <mjt@debian.org>"
# Primary key fingerprint: 6EE1 95D1 886E 8FFB 810D 4324 457C E0A0 8044 65C5
# Subkey fingerprint: 7B73 BAD6 8BE7 A2C2 8931 4B22 701B 4F6B 1A69 3E59
* remotes/mjt/tags/trivial-patches-fetch: (23 commits)
Fix build for less common build directories names
clean-up: removed duplicate #includes
scripts/clean-includes: added duplicate #include check
monitor: deprecate 'default' option
qemu-ga: Remove stray 'q' in documentation
Makefile: Fix help text for target 'installer'
s390: avoid always-true comparison in s390_pci_generate_fid()
migration: Remove unneeded NULL check from migrate_fd_error()
scripts/hxtool: fix undefined behavour of echo
qemu-options.hx: set: fix copy-paste error
usb: Change *_exitfn return type from int to void
MAINTAINERS: qemu-trivial information
colo-compare: remove unused struct CompareChardevProps and 'props' variable
milkymist-pfpu: fix potential integer overflow
hw/block/nvme: Simplify if-statements a little bit
target-lm32: rewrite gen_compare()
lm32: milkymist-tmu2: fix integer overflow
target-lm32: disable asm logging via LOG_DIS()
target-lm32: swap operand of wcsr in LOG_DIS()
target-lm32: fix LOG_DIS operand order
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
'remotes/pmaydell/tags/pull-target-arm-20161028' into staging
target-arm queue:
* Fix reset GPIO handling for spitz, tosa boards
* virt: add 'pmu' property for configuring whether to expose the
vPMU to the guest
* char: cadence: correct reset value for baud rate registers
* versatilepb: do not run if user asks for more than 256MB RAM
* pxa2xx: Set value default values for CCCR and CKEN on PXA255
* arm: cubieboard: Add support for initrd
* i.MX: Fix GPIO ISR register write
# gpg: Signature made Fri 28 Oct 2016 15:56:56 BST
# gpg: using RSA key 0x3C2525ED14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE
* remotes/pmaydell/tags/pull-target-arm-20161028:
hw/arm/tosa: Fix reset handling
hw/arm/spitz: Fix reset handling
arm: virt: add PMU property to mach-virt machine type
arm: Add an option to turn on/off vPMU support
char: cadence: correct reset value for baud rate registers
versatilepb: do not run if user asks for more than 256MB RAM
hw/arm/pxa2xx: Set value default values for CCCR and CKEN on PXA255
arm: cubieboard: Add support for initrd
i.MX: Fix GPIO ISR register write
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
# gpg: Signature made Fri 28 Oct 2016 15:47:39 BST
# gpg: using RSA key 0xCA35624C6A9171C6
# gpg: Good signature from "Fam Zheng <famz@redhat.com>"
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 5003 7CB7 9706 0F76 F021 AD56 CA35 624C 6A91 71C6
* remotes/famz/tags/for-upstream:
aio: convert from RFifoLock to QemuRecMutex
qemu-thread: introduce QemuRecMutex
iothread: release AioContext around aio_poll
block: only call aio_poll on the current thread's AioContext
qemu-img: call aio_context_acquire/release around block job
qemu-io: acquire AioContext
block: prepare bdrv_reopen_multiple to release AioContext
replication: pass BlockDriverState to reopen_backing_file
iothread: detach all block devices before stopping them
aio: introduce qemu_get_current_aio_context
sheepdog: use BDRV_POLL_WHILE
nfs: use BDRV_POLL_WHILE
nfs: move nfs_set_events out of the while loops
block: introduce BDRV_POLL_WHILE
qed: Implement .bdrv_drain
block: change drain to look only at one child at a time
block: add BDS field to count in-flight requests
mirror: use bdrv_drained_begin/bdrv_drained_end
blockjob: introduce .drain callback for jobs
replication: interrupt failover if the main device is closed
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The instructions PCI STORE, PCI LOAD and PCI STORE BLOCK
use calls to memory_region_dispatch_write() and
memory_region_dispatch_read() but do not test the return value.
Furthermore, the instruction PCI STORE BLOCK sets up a PGM_ADDRESSING
exception when the operand 3 is not within the designated PCI address
space instead of a PGM_OPERAND exception.
Let's setup a PGM_OPERAND exception in all of these failure cases.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
Let's use the generic interface to inject adapter interrupts.
Signed-off-by: Yi Min Zhao <zyimin@linux.vnet.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
Add myself as co-maintainer of COLO framework, so that
I can get CC'ed on future patches and bugs for this feature.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
|
|
configure --enable-colo/--disable-colo to switch COLO
support on/off.
COLO feature doesn't depend on any other external libraries,
So here it is reasonable to enable COLO by default, to
avoid re-compile QEMU if users want to use this capability.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
|
|
Introduce the design of COLO, and how to test it.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
|
|
If users require SVM to takeover work, COLO incoming thread should
exit from loop while failover BH helps backing to migration incoming
coroutine.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
|
|
For primary side, if COLO gets failover request from users.
To be exact, gets 'x_colo_lost_heartbeat' command.
COLO thread will exit the loop while the failover BH does the
cleanup work and resumes VM.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
|
|
When handling failover, COLO processes differently according to
the different stage of failover process, here we introduce a global
atomic variable to record the status of failover.
We add four failover status to indicate the different stage of failover process.
You should use the helpers to get and set the value.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
|
|
We leave users to choose whatever heartbeat solution they want,
if the heartbeat is lost, or other errors they detect, they can use
experimental command 'x_colo_lost_heartbeat' to tell COLO to do failover,
COLO will do operations accordingly.
For example, if the command is sent to the Primary side,
the Primary side will exit COLO mode, does cleanup work,
and then, PVM will take over the service work. If sent to the Secondary side,
the Secondary side will run failover work, then takes over PVM's service work.
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Eric Blake <eblake@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
|
|
Do checkpoint periodically, the default interval is 200ms.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
|
|
Add checkpoint-delay parameter for migrate-set-parameters, so that
we can control the checkpoint frequency when COLO is in periodic mode.
Cc: Luiz Capitulino <lcapitulino@redhat.com>
Cc: Eric Blake <eblake@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
|
|
We should not destroy the state of SVM (Secondary VM) until we receive
the complete data of PVM's state, in case the primary fails in the process
of sending the state, so we cache the VM's state in secondary side before
load it into SVM.
Besides, we should call qemu_system_reset() before load VM state,
which can ensure the data is intact.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
|
|
VM checkpointing is to synchronize the state of PVM to SVM, just
like migration does, we re-use save helpers to achieve migrating
PVM's state to Secondary side.
COLO need to cache the data of VM's state in the secondary side before
synchronize it to SVM. COLO need the size of the data to determine
how much data should be read in the secondary side.
So here, we can get the size of the data by saving it into I/O channel
before send it to the secondary side.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
|
|
Guest will enter this state when paused to save/restore VM state
under COLO checkpoint.
Cc: Eric Blake <eblake@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
|
|
We need communications protocol of user-defined to control
the checkpointing process.
The new checkpointing request is started by Primary VM,
and the interactive process like below:
Checkpoint synchronizing points:
Primary Secondary
initial work
'checkpoint-ready' <-------------------- @
'checkpoint-request' @ -------------------->
Suspend (Only in hybrid mode)
'checkpoint-reply' <-------------------- @
Suspend&Save state
'vmstate-send' @ -------------------->
Send state Receive state
'vmstate-received' <-------------------- @
Release packets Load state
'vmstate-load' <-------------------- @
Resume Resume (Only in hybrid mode)
Start Comparing (Only in hybrid mode)
NOTE:
1) '@' who sends the message
2) Every sync-point is synchronized by two sides with only
one handshake(single direction) for low-latency.
If more strict synchronization is required, a opposite direction
sync-point should be added.
3) Since sync-points are single direction, the remote side may
go forward a lot when this side just receives the sync-point.
4) For now, we only support 'periodic' checkpoint, for which
the Secondary VM is not running, later we will support 'hybrid' mode.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Cc: Eric Blake <eblake@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
|
|
This new communication path will be used for returning messages
from Secondary side to Primary side.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
|
|
Switch from normal migration loadvm process into COLO checkpoint process if
COLO mode is enabled.
We add three new members to struct MigrationIncomingState,
'have_colo_incoming_thread' and 'colo_incoming_thread' record the COLO
related thread for secondary VM, 'migration_incoming_co' records the
original migration incoming coroutine.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
|
|
Add a new migration state: MIGRATION_STATUS_COLO. Migration source side
enters this state after the first live migration successfully finished
if COLO is enabled by command 'migrate_set_capability x-colo on'.
We reuse migration thread, so the process of checkpointing will be handled
in migration thread.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
|
|
We can determine whether or not VM in destination should go into COLO mode
by referring to the info that was migrated.
We skip this section if COLO is not enabled (i.e.
migrate_set_capability colo off), so that, It doesn't break compatibility
with migration no matter whether users configure the --enable-colo/disable-colo
on the source/destination side or not;
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Dr. David Alan Gilbert <dgilbert@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
|
|
We add helper function colo_supported() to indicate whether
colo is supported or not, with which we use to control whether or not
showing 'x-colo' string to users, they can use qmp command
'query-migrate-capabilities' or hmp command 'info migrate_capabilities'
to learn if colo is supported.
The default value for COLO (COarse-Grain LOck Stepping) is disabled.
Cc: Juan Quintela <quintela@redhat.com>
Cc: Amit Shah <amit.shah@redhat.com>
Cc: Eric Blake <eblake@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Signed-off-by: Gonglei <arei.gonglei@huawei.com>
Reviewed-by: Eric Blake <eblake@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Amit Shah <amit@amitshah.net>
|
|
Prepare xen_be_del_xendev to be shared with frontends:
* xen_be_del_xendev -> xen_pv_del_xendev
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
|
|
Prepare xen_be_find_xendev to be shared with frontends:
* xen_be_find_xendev -> xen_pv_find_xendev
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
|
|
Prepare xen_be_evtchn_event to be shared with frontends:
* xen_be_evtchn_event -> xen_pv_evtchn_event
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
|
|
Prepare xen_be_send_notify to be shared with frontends:
* xen_be_send_notify -> xen_pv_send_notify
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
|
|
Prepare xen_be_unbind_evtchn to be shared with frontends:
* xen_be_unbind_evtchn -> xen_pv_unbind_evtchn
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
|
|
Prepare xen_be_printf to be used by both backend and frontends:
* xen_be_printf -> xen_pv_printf
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
|
|
The name of the functions moved to xen_pvdev.c:
* xenstore_cleanup_dir
* xen_config_cleanup
* xenstore_mkdir
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
|
|
* move xendevs qtail to xen_pvdev.c
* change xen_be_get_xendev to use a new function: xen_pv_insert_xendev
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
|
|
The name of the functions moved:
* xen_be_evtchn_event
* xen_be_unbind_evtchn
* xen_be_send_notify
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
|
|
* xenstore_update -> xen_pvdev.c
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
|
|
The purpose of the new file is to store generic functions shared by frontend
and backends such as xenstore operations, xendevs.
Signed-off-by: Quan Xu <quan.xu@intel.com>
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
|
|
Fixes:
* WARNING: line over 80 characters
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
|
|
Fixes the following errors:
* ERROR: line over 90 characters
* ERROR: code indent should never use tabs
* ERROR: space prohibited after that open square bracket '['
* ERROR: do not initialise statics to 0 or NULL
* ERROR: "(foo*)" should be "(foo *)"
Signed-off-by: Emil Condrea <emilcondrea@gmail.com>
Signed-off-by: Stefano Stabellini <sstabellini@kernel.org>
Signed-off-by: Quan Xu <xuquan8@huawei.com>
Acked-by: Anthony PERARD <anthony.perard@citrix.com>
|
|
It seems there is a limit to the number of arguments a UST trace event
can take and at 11 the previous trace command broke the build. Split the
trace into a src pkt and dst pkt trace to fix this.
Signed-off-by: Alex Bennée <alex.bennee@linaro.org>
Message-id: 20161028132559.8324-1-alex.bennee@linaro.org
Reviewed-by: Peter Maydell <peter.maydell@linaro.org>
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
staging
braille fixes and improvements.
curses fix, switch to cursesw.
gtk bugfixes.
# gpg: Signature made Fri 28 Oct 2016 13:05:12 BST
# gpg: using RSA key 0x4CB6D8EED3E87138
# gpg: Good signature from "Gerd Hoffmann (work) <kraxel@redhat.com>"
# gpg: aka "Gerd Hoffmann <gerd@kraxel.org>"
# gpg: aka "Gerd Hoffmann (private) <kraxel@gmail.com>"
# Primary key fingerprint: A032 8CFF B93A 17A7 9901 FE7D 4CB6 D8EE D3E8 7138
* remotes/kraxel/tags/pull-ui-20161028-1:
curses: Use cursesw instead of curses
curses: fix left/right arrow translation
ui/gtk: Fix non-working DELETE key
gtk: fix compilation warning with gtk 3.22.2
Defer BrlAPI tty acquisition to when guest starts using device
Add dots keypresses support to the baum braille device
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
into staging
# gpg: Signature made Fri 28 Oct 2016 09:44:23 BST
# gpg: using RSA key 0xF30C38BD3F2FBE3C
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>"
# gpg: aka "Laurent Vivier <laurent@vivier.eu>"
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>"
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C
* remotes/vivier/tags/m68k-part2-pull-request:
MAINTAINERS: update M68K entry
target-m68k: immediate ops manage word and byte operands
target-m68k: cmp manages word and bytes operands
target-m68k: add/sub manage word and byte operands
target-m68k: add addressing modes to neg
target-m68k: introduce byte and word cc_ops
target-m68k: some bit ops cleanup
target-m68k: suba/adda can manage word operand
target-m68k: and can manage word and byte operands
target-m68k: or can manage word and byte operands
target-m68k: eor can manage word and byte operands
target-m68k: add addressing modes to not
target-m68k: Inline addx, subx, negx
target-m68k: add dbcc
target-m68k: add addressing modes to scc
target-m68k: add exg ops
target-m68k: add linkl
target-m68k: add bkpt instruction
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
into staging
ppc patch queue 2016-10-28
This pull request supersedes and extends the one from 2016-10-26
(which had a build bug).
Highlights:
* SLOF (pseries guest firmware) update
* Enable a number of extra testcases on ppc / pseries
* Added the 'powernv' machine type
- Almost enough to be minimally usable
- But still missing necessary interrupt controller updates
* Cleanup and consolidation of NVRAM handling on several platforms
with related firmware
* Substantial cleanup to device tree construction
* Some more POWER9 instruction emulation
* Cleanup to handling of pseries option vectors and CAS reboot
handling (host/guest feature negotiation mechanism)
* Significant cleanups to handling of PCI devices in test cases
* New hotplug event infrastructure
* Memory hot unplug support for pseries
* Several bug fixes
The NVRAM cleanup affects some Sun sparc platforms as well as ppc
ones, but have been tested by the sparc maintainer (Mark Cave-Ayland).
The test additions also include substantial general changes to the
test framework that aren't strictly ppc related. They don't seem to
break tests on other platforms, they're for the benefit of enabling
tests on ppc and there isn't a specific maintainer for them, so
they're included in this tree.
# gpg: Signature made Fri 28 Oct 2016 02:37:19 BST
# gpg: using RSA key 0x6C38CACA20D9B392
# gpg: Good signature from "David Gibson <david@gibson.dropbear.id.au>"
# gpg: aka "David Gibson (Red Hat) <dgibson@redhat.com>"
# gpg: aka "David Gibson (ozlabs.org) <dgibson@ozlabs.org>"
# gpg: aka "David Gibson (kernel.org) <dwg@kernel.org>"
# Primary key fingerprint: 75F4 6586 AE61 A66C C44E 87DC 6C38 CACA 20D9 B392
* remotes/dgibson/tags/ppc-for-2.8-20161028: (73 commits)
ppc: allow certain HV interrupts to be delivered to guests
spapr: Memory hot-unplug support
spapr: use count+index for memory hotplug
spapr: Add DRC count indexed hotplug identifier type
spapr: add hotplug interrupt machine options
spapr_events: add support for dedicated hotplug event source
spapr: update spapr hotplug documentation
target-ppc: Add xvcmpnesp, xvcmpnedp instructions
target-ppc: add xscmp[eq,gt,ge,ne]dp instructions
tests: Add pseries machine to the prom-env-test, too
spapr_nvram: Pre-initialize the NVRAM to support the -prom-env parameter
libqos: Change PCI accessors to take opaque BAR handle
tests: Don't assume structure of PCI IO base in ahci-test
tests: Use qpci_mem{read,write} in ivshmem-test
libqos: Add 64-bit PCI IO accessors
tests: Clean up IO handling in ide-test
libqos: Implement mmio accessors in terms of mem{read,write}
libqos: Add streaming accessors for PCI MMIO
tests: Adjust tco-test to use qpci_legacy_iomap()
libqos: Better handling of PCI legacy IO
...
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
scripts/tracetool generates a C preprocessor macro from the name of the
build directory. Any characters which are possible in a directory name
but not allowed in a macro name must be substituted, otherwise builds
will fail.
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
Some files contain multiple #includes of the same header file.
Removed most of those unnecessary duplicate entries using
scripts/clean-includes.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Anand J <anand.indukala@gmail.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
Enhance the clean-includes script to optionally check for duplicate #include
entries.
Script might output false positive entries as well. Such entries should
not be removed. So if it finds any duplicate entries script will
terminate with an exit status 1. Then each and every file should be
checked manually and corrected if necessary.
In order to enable the check use --check-dup-head option with
scripts/clean-includes.
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Anand J <anand.indukala@gmail.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
This option does nothing since commit 06ac27f. Deprecate it.
Signed-off-by: Marc-André Lureau <marcandre.lureau@redhat.com>
Reviewed-by: Markus Armbruster <armbru@redhat.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
|
Signed-off-by: Stefan Weil <sw@weilnetz.de>
Reviewed-by: Michael Roth <mdroth@linux.vnet.ibm.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
|
