| Age | Commit message (Collapse) | Author |
|---|
|
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1454089805-5470-16-git-send-email-peter.maydell@linaro.org
|
|
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1454089805-5470-15-git-send-email-peter.maydell@linaro.org
|
|
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1454089805-5470-14-git-send-email-peter.maydell@linaro.org
|
|
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1454089805-5470-13-git-send-email-peter.maydell@linaro.org
|
|
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1454089805-5470-12-git-send-email-peter.maydell@linaro.org
|
|
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1454089805-5470-11-git-send-email-peter.maydell@linaro.org
|
|
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1454089805-5470-10-git-send-email-peter.maydell@linaro.org
|
|
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1454089805-5470-9-git-send-email-peter.maydell@linaro.org
|
|
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Eric Blake <eblake@redhat.com>
Message-id: 1454089805-5470-8-git-send-email-peter.maydell@linaro.org
|
|
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1454089805-5470-7-git-send-email-peter.maydell@linaro.org
|
|
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1454089805-5470-6-git-send-email-peter.maydell@linaro.org
|
|
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1454089805-5470-5-git-send-email-peter.maydell@linaro.org
|
|
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1454089805-5470-4-git-send-email-peter.maydell@linaro.org
|
|
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1454089805-5470-3-git-send-email-peter.maydell@linaro.org
|
|
Clean up includes so that osdep.h is included first and headers
which it implies are not included manually.
This commit was created with scripts/clean-includes.
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 1454089805-5470-2-git-send-email-peter.maydell@linaro.org
|
|
into staging
Update OpenBIOS images
# gpg: Signature made Thu 04 Feb 2016 11:18:01 GMT using RSA key ID AE0F321F
# gpg: Good signature from "Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>"
* remotes/mcayland/tags/qemu-openbios-signed:
Update OpenBIOS images
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
staging
# gpg: Signature made Thu 04 Feb 2016 08:26:24 GMT using RSA key ID 398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>"
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211
* remotes/jasowang/tags/net-pull-request:
net/filter: Fix the output information for command 'info network'
net: always walk through filters in reverse if traffic is egress
net: netmap: use nm_open() to open netmap ports
e1000: eliminate infinite loops on out-of-bounds transfer start
slirp: Adding family argument to tcp_fconnect()
slirp: Make udp_attach IPv6 compatible
slirp: Add sockaddr_equal, make solookup family-agnostic
slirp: Factorizing and cleaning solookup()
slirp: Factorizing address translation
slirp: Make Socket structure IPv6 compatible
slirp: Adding address family switch for produced frames
slirp: Generalizing and neutralizing ARP code
slirp: goto bad in udp_input if sosendto fails
cadence_gem: fix buffer overflow
net: cadence_gem: check packet size in gem_recieve
qemu-doc: Do not promote deprecated -smb and -redir options
net/slirp: Tell the users when they are using deprecated options
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
# gpg: Signature made Wed 03 Feb 2016 20:29:54 GMT using RSA key ID AAFC390E
# gpg: Good signature from "John Snow (John Huston) <jsnow@redhat.com>"
* remotes/jnsnow/tags/ide-pull-request:
dma: remove now useless DMA_* functions
sb16: use IsaDma interface instead of global DMA_* functions
gus: use IsaDma interface instead of global DMA_* functions
cs4231a: use IsaDma interface instead of global DMA_* functions
fdc: use IsaDma interface instead of global DMA_* functions
sparc64: disable floppy DMA
sparc: disable floppy DMA
magnum: disable floppy DMA for now
i8257: implement the IsaDma interface
isa: add an ISA DMA interface, and store it within the ISA bus
i8257: move state definition to new independent header
i8257: QOM'ify
i8257: add missing const
i8257: make the DMA running method per controller
i8257: rename functions to start with i8257_ prefix
i8257: rename struct dma_regs to I8257Regs
i8257: rename struct dma_cont to I8257State
i8257: pass ISA bus to DMA_init() function
i82374: device only existed as ISA device, so simplify device
fdc: fix detection under Linux
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Update OpenBIOS images to SVN r1378 built from submodule.
Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
|
|
'remotes/pmaydell/tags/pull-target-arm-20160203' into staging
target-arm queue:
* virt-acpi-build: add always-on property for timer
* various fixes for EL2 and EL3 behaviour
* arm: virt-acpi: each MADT.GICC entry as enabled unconditionally
* target-arm: Don't report presence of EL2 if it doesn't exist
* raspi: add raspberry pi 2 machine
# gpg: Signature made Wed 03 Feb 2016 18:58:02 GMT using RSA key ID 14360CDE
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>"
# gpg: aka "Peter Maydell <pmaydell@gmail.com>"
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>"
* remotes/pmaydell/tags/pull-target-arm-20160203:
raspi: add raspberry pi 2 machine
arm/boot: move highbank secure board setup code to common routine
bcm2836: add bcm2836 SoC device
bcm2836_control: add bcm2836 ARM control logic
bcm2835_peripherals: add rollup device for bcm2835 peripherals
bcm2835_ic: add bcm2835 interrupt controller
bcm2835_property: add bcm2835 property channel
bcm2835_mbox: add BCM2835 mailboxes
target-arm: Don't report presence of EL2 if it doesn't exist
libvixl: Avoid std::abs() of 64-bit type
arm: virt-acpi: each MADT.GICC entry as enabled unconditionally
target-arm: Implement the S2 MMU inputsize > pamax check
target-arm: Rename check_s2_startlevel to check_s2_mmu_setup
target-arm: Apply S2 MMU startlevel table size check to AArch64
hw/arm: Setup EL1 and EL2 in AArch64 mode for 64bit Linux boots
target-arm: Make various system registers visible to EL3
virt-acpi-build: add always-on property for timer
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
The properties of netfilter object could be changed by 'qom-set'
command, but the output of 'info network' command is not updated,
because it got the old information through nf->info_str, it will
not be updated while we change the value of netfilter's property.
Here we split a helper function that could collect the output
information for filter, and also remove the useless member
'info_str' from struct NetFilterState.
Signed-off-by: zhanghailiang <zhang.zhanghailiang@huawei.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Eric Blake <eblake@redhat.com>
Cc: Markus Armbruster <armbru@redhat.com>
Cc: Yang Hongyang <hongyang.yang@easystack.cn>
Reviewed-by: Eric Blake <eblake@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Previously, if we attach more than one filters for a single netdev,
both ingress and egress traffic will go through net filters in same
order like:
ingress: netdev ->filter1 ->filter2 ->...filter[n] ->emulated device
egress: emulated device ->filter1 ->filter2 ->...filter[n] ->netdev.
This is against the natural feeling and will complicate filters
configuration since in some scenes, we hope filters handle the egress
traffic in a reverse order. For example, in colo-proxy (will be
implemented later), we have a redirector filter and a colo-rewriter
filter, we need the filter behave like:
ingress(->)/egress(<-): chardev<->redirector<->colo-rewriter<->emulated device
Since both buffer filter and dump do not require strict order of
filters, this patch switches to always let egress traffic walk through
net filters in reverse to simplify the possible filters configuration
in the future.
Signed-off-by: Wen Congyang <wency@cn.fujitsu.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Reviewed-by: Yang Hongyang <hongyang.yang@easystack.cn>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
This patch simplifies the netmap backend code by means of the nm_open()
helper function provided by netmap_user.h, which hides the details of
open(), iotcl() and mmap() carried out on the netmap device.
Moreover, the semantic of nm_open() makes it possible to open special
netmap ports (e.g. pipes, monitors) and use special modes (e.g. host rings
only, single queue mode, exclusive access).
Signed-off-by: Vincenzo Maffione <v.maffione@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
The start_xmit() and e1000_receive_iov() functions implement DMA transfers
iterating over a set of descriptors that the guest's e1000 driver
prepares:
- the TDLEN and RDLEN registers store the total size of the descriptor
area,
- while the TDH and RDH registers store the offset (in whole tx / rx
descriptors) into the area where the transfer is supposed to start.
Each time a descriptor is processed, the TDH and RDH register is bumped
(as appropriate for the transfer direction).
QEMU already contains logic to deal with bogus transfers submitted by the
guest:
- Normally, the transmit case wants to increase TDH from its initial value
to TDT. (TDT is allowed to be numerically smaller than the initial TDH
value; wrapping at or above TDLEN bytes to zero is normal.) The failsafe
that QEMU currently has here is a check against reaching the original
TDH value again -- a complete wraparound, which should never happen.
- In the receive case RDH is increased from its initial value until
"total_size" bytes have been received; preferably in a single step, or
in "s->rxbuf_size" byte steps, if the latter is smaller. However, null
RX descriptors are skipped without receiving data, while RDH is
incremented just the same. QEMU tries to prevent an infinite loop
(processing only null RX descriptors) by detecting whether RDH assumes
its original value during the loop. (Again, wrapping from RDLEN to 0 is
normal.)
What both directions miss is that the guest could program TDLEN and RDLEN
so low, and the initial TDH and RDH so high, that these registers will
immediately be truncated to zero, and then never reassume their initial
values in the loop -- a full wraparound will never occur.
The condition that expresses this is:
xdh_start >= s->mac_reg[XDLEN] / sizeof(desc)
i.e., TDH or RDH start out after the last whole rx or tx descriptor that
fits into the TDLEN or RDLEN sized area.
This condition could be checked before we enter the loops, but
pci_dma_read() / pci_dma_write() knows how to fill in buffers safely for
bogus DMA addresses, so we just extend the existing failsafes with the
above condition.
This is CVE-2016-1981.
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Prasad Pandit <ppandit@redhat.com>
Cc: Michael Roth <mdroth@linux.vnet.ibm.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: qemu-stable@nongnu.org
RHBZ: https://bugzilla.redhat.com/show_bug.cgi?id=1296044
Signed-off-by: Laszlo Ersek <lersek@redhat.com>
Reviewed-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
This patch simply adds a unsigned short family argument to remove the hardcoded
"AF_INET" in the call of qemu_socket().
This prepares for IPv6 support.
Signed-off-by: Guillaume Subiron <maethor@subiron.org>
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
A unsigned short is now passed in argument to udp_attach instead of using a
hardcoded "AF_INET" to call qemu_socket().
This prepares for IPv6 support.
Signed-off-by: Guillaume Subiron <maethor@subiron.org>
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
This patch makes solookup() compatible with varying address
families, by using a new sockaddr_equal() function that compares
two sockaddr_storage.
This prepares for IPv6 support.
Signed-off-by: Guillaume Subiron <maethor@subiron.org>
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
solookup() was only compatible with TCP. Having the socket list in
argument, it is now compatible with UDP too.
Some optimization code is factorized inside the function (the function
look at the last returned result before browsing the complete socket
list).
This prepares for IPv6 support.
Signed-off-by: Guillaume Subiron <maethor@subiron.org>
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
This patch factorizes some duplicate code into a new function,
sotranslate_out(). This function perform the address translation when a
packet is transmitted to the host network. If the packet is destinated
to the host, the loopback address is used, and if the packet is
destinated to the virtual DNS, the real DNS address is used. This code
is just a copy of the existent, but factorized and ready to manage the
IPv6 case.
On the same model, the major part of udp_output() code is moved into a
new sotranslate_in(). This function is directly used in sorecvfrom(),
like sotranslate_out() in sosendto().
udp_output() becoming useless, it is removed and udp_output2() is
renamed into udp_output(). This adds consistency with the udp6_output()
function introduced by further patches.
Lastly, this factorizes some duplicate code into sotranslate_accept(), which
performs the address translation when a connection is established on the host
for port forwarding: if it comes from localhost, the host virtual address is
used instead.
This prepares for IPv6 support.
Signed-off-by: Guillaume Subiron <maethor@subiron.org>
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
This patch replaces foreign and local address/port couples in Socket
structure by 2 sockaddr_storage which can be casted in sockaddr_in.
Direct access to address and port is still possible thanks to some
\#define, so retrocompatibility of the existing code is assured.
The ss_family field of sockaddr_storage is declared after each socket
creation.
The whole structure is also saved/restored when a Qemu session is
saved/restored.
This prepares for IPv6 support.
Signed-off-by: Guillaume Subiron <maethor@subiron.org>
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
In if_encap, a switch is added to prepare for the IPv6 case. Some code
is factorized.
This prepares for IPv6 support.
Signed-off-by: Guillaume Subiron <maethor@subiron.org>
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
|
|
Basically, this patch replaces "arp" by "resolution" every time "arp"
means "mac resolution" and not specifically ARP.
This prepares for IPv6 support.
Signed-off-by: Guillaume Subiron <maethor@subiron.org>
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Before this patch, if sosendto fails, udp_input is executed as if the
packet was sent, recording the packet for icmp errors, which does not
makes sense since the packet was not actually sent, errors would be
related to a previous packet.
This patch adds a goto bad to cut the execution of this function.
Signed-off-by: Guillaume Subiron <maethor@subiron.org>
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
gem_transmit copies a packet from guest into an tx_packet[2048]
array on stack, with size limited by descriptor length set by guest. If
guest is malicious and specifies a descriptor length that is too large,
and should packet size exceed array size, this results in a buffer
overflow.
Reported-by: 刘令 <liuling-it@360.cn>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
While receiving packets in 'gem_receive' routine, if Frame Check
Sequence(FCS) is enabled, it copies the packet into a local
buffer without checking its size. Add check to validate packet
length against the buffer size to avoid buffer overflow.
Reported-by: Ling Liu <liuling-it@360.cn>
Signed-off-by: Prasad J Pandit <pjp@fedoraproject.org>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
Since -smb and -redir are deprecated options, we should not
use them as examples in the documentation anymore.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
We don't want to support the legacy -tftp, -bootp, -smb and
-net channel options forever. So let's start telling the users
that they are deprecated and what option should be used instead.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
|
|
into staging
# gpg: Signature made Wed 03 Feb 2016 15:47:34 GMT using RSA key ID 81AB73C8
# gpg: Good signature from "Stefan Hajnoczi <stefanha@redhat.com>"
# gpg: aka "Stefan Hajnoczi <stefanha@gmail.com>"
* remotes/stefanha/tags/tracing-pull-request:
log: add "-d trace:PATTERN"
trace: switch default backend to "log"
trace: convert stderr backend to log
log: move qemu-log.c into util/ directory
log: do not unnecessarily include qom/cpu.h
trace: add "-trace help"
trace: add "-trace enable=..."
trace: no need to call trace_backend_init in different branches now
trace: split trace_init_file out of trace_init_backends
trace: split trace_init_events out of trace_init_backends
trace: fix documentation
trace: track enabled events in a separate array
trace: count number of enabled events
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
|
|
Keep only DMA_init function as a wrapper around DMA controllers creation.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-20-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
|
|
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-19-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
|
|
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-18-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
|
|
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-17-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
|
|
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-16-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
|
|
All functions relative to DMA (DMA_*() functions) are stubs on sparc64 platform.
Disable the DMA of the floppy controller, instead of calling these stubs.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-15-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
|
|
All functions relative to DMA (DMA_*() functions) are stubs on sparc platform.
Disable the DMA in the floppy controller, instead of calling these stubs.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-14-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
|
|
Floppy uses the DMA controller in rc4030 chipset, and not the i8259 from the ISA bus.
It's better to disable DMA than to call the wrong DMA controller.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-13-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
|
|
Rewrite the global DMA_*() functions to use the IsaDma interface.
Note that these functions will be deleted in a few commits.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-12-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
|
|
This will permit to deprecate global DMA_*() functions.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-11-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
|
|
We will now be able to embed the i8257 interrupt controller in another object.
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-10-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
|
|
Signed-off-by: Hervé Poussineau <hpoussin@reactos.org>
Message-id: 1453843944-26833-9-git-send-email-hpoussin@reactos.org
Signed-off-by: John Snow <jsnow@redhat.com>
|
