diff options
Diffstat (limited to 'hw/pl181.c')
| -rw-r--r-- | hw/pl181.c | 45 |
1 files changed, 34 insertions, 11 deletions
diff --git a/hw/pl181.c b/hw/pl181.c index c0b89f775a..912465971f 100644 --- a/hw/pl181.c +++ b/hw/pl181.c @@ -36,9 +36,14 @@ typedef struct { uint32_t datacnt; uint32_t status; uint32_t mask[2]; - uint32_t fifocnt; int fifo_pos; int fifo_len; + /* The linux 2.6.21 driver is buggy, and misbehaves if new data arrives + while it is reading the FIFO. We hack around this be defering + subsequent transfers until after the driver polls the status word. + http://www.arm.linux.org.uk/developer/patches/viewpatch.php?id=4446/1 + */ + int linux_hack; uint32_t fifo[PL181_FIFO_LEN]; qemu_irq irq[2]; } pl181_state; @@ -182,7 +187,8 @@ static void pl181_fifo_run(pl181_state *s) int is_read; is_read = (s->datactrl & PL181_DATA_DIRECTION) != 0; - if (s->datacnt != 0 && (!is_read || sd_data_ready(s->card))) { + if (s->datacnt != 0 && (!is_read || sd_data_ready(s->card)) + && !s->linux_hack) { limit = is_read ? PL181_FIFO_LEN : 0; n = 0; value = 0; @@ -217,7 +223,7 @@ static void pl181_fifo_run(pl181_state *s) s->status |= PL181_STATUS_DATABLOCKEND; DPRINTF("Transfer Complete\n"); } - if (s->datacnt == 0 && s->fifocnt == 0) { + if (s->datacnt == 0 && s->fifo_len == 0) { s->datactrl &= ~PL181_DATA_ENABLE; DPRINTF("Data engine idle\n"); } else { @@ -252,6 +258,7 @@ static void pl181_fifo_run(pl181_state *s) static uint32_t pl181_read(void *opaque, target_phys_addr_t offset) { pl181_state *s = (pl181_state *)opaque; + uint32_t tmp; offset -= s->base; if (offset >= 0xfe0 && offset < 0x1000) { @@ -285,24 +292,42 @@ static uint32_t pl181_read(void *opaque, target_phys_addr_t offset) case 0x30: /* DataCnt */ return s->datacnt; case 0x34: /* Status */ - return s->status; + tmp = s->status; + if (s->linux_hack) { + s->linux_hack = 0; + pl181_fifo_run(s); + pl181_update(s); + } + return tmp; case 0x3c: /* Mask0 */ return s->mask[0]; case 0x40: /* Mask1 */ return s->mask[1]; case 0x48: /* FifoCnt */ - return s->fifocnt; + /* The documentation is somewhat vague about exactly what FifoCnt + does. On real hardware it appears to be when decrememnted + when a word is transfered between the FIFO and the serial + data engine. DataCnt is decremented after each byte is + transfered between the serial engine and the card. + We don't emulate this level of detail, so both can be the same. */ + tmp = (s->datacnt + 3) >> 2; + if (s->linux_hack) { + s->linux_hack = 0; + pl181_fifo_run(s); + pl181_update(s); + } + return tmp; case 0x80: case 0x84: case 0x88: case 0x8c: /* FifoData */ case 0x90: case 0x94: case 0x98: case 0x9c: case 0xa0: case 0xa4: case 0xa8: case 0xac: case 0xb0: case 0xb4: case 0xb8: case 0xbc: - if (s->fifocnt == 0) { + if (s->fifo_len == 0) { fprintf(stderr, "pl181: Unexpected FIFO read\n"); return 0; } else { uint32_t value; - s->fifocnt--; value = pl181_fifo_pop(s); + s->linux_hack = 1; pl181_fifo_run(s); pl181_update(s); return value; @@ -356,7 +381,6 @@ static void pl181_write(void *opaque, target_phys_addr_t offset, s->datactrl = value & 0xff; if (value & PL181_DATA_ENABLE) { s->datacnt = s->datalength; - s->fifocnt = (s->datalength + 3) >> 2; pl181_fifo_run(s); } break; @@ -373,10 +397,9 @@ static void pl181_write(void *opaque, target_phys_addr_t offset, case 0x90: case 0x94: case 0x98: case 0x9c: case 0xa0: case 0xa4: case 0xa8: case 0xac: case 0xb0: case 0xb4: case 0xb8: case 0xbc: - if (s->fifocnt == 0) { + if (s->datacnt == 0) { fprintf(stderr, "pl181: Unexpected FIFO write\n"); } else { - s->fifocnt--; pl181_fifo_push(s, value); pl181_fifo_run(s); } @@ -418,9 +441,9 @@ static void pl181_reset(void *opaque) s->datactrl = 0; s->datacnt = 0; s->status = 0; + s->linux_hack = 0; s->mask[0] = 0; s->mask[1] = 0; - s->fifocnt = 0; } void pl181_init(uint32_t base, BlockDriverState *bd, |