pci: initialize pci config headers depending it pci header type.

- Only sets default subsystem id for header type 00.(normal header type)
  because header type 01 doesn't have subsystem id, and uses the register
  for other purpose. So setting default subsystem id doesn't make sense.

- initialize wmask more for header type 01.(bridge header type)
  Without those wmasks, linux was confused not boot,
  and lspci was confused not to print out expected IO/memory range.

Signed-off-by: Isaku Yamahata <yamahata@valinux.co.jp>
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>

1 files changed, 29 insertions, 0 deletions

diff --git a/hw/pci.h b/hw/pci.h
index 7991bfdf49..3f50294346 100644
--- a/hw/pci.h
+++ b/hw/pci.h
@@ -100,6 +100,14 @@ typedef struct PCIIORegion {
 #define  PCI_COMMAND_IO		0x1	/* Enable response in I/O space */
 #define  PCI_COMMAND_MEMORY	0x2	/* Enable response in Memory space */
 #define  PCI_COMMAND_MASTER	0x4	/* Enable bus master */
+#define  PCI_COMMAND_SPECIAL	0x8	/* Enable response to special cycles */
+#define  PCI_COMMAND_INVALIDATE 0x10	/* Use memory write and invalidate */
+#define  PCI_COMMAND_VGA_PALETTE 0x20	/* Enable palette snooping */
+#define  PCI_COMMAND_PARITY	0x40	/* Enable parity checking */
+#define  PCI_COMMAND_WAIT	0x80	/* Enable address/data stepping */
+#define  PCI_COMMAND_SERR	0x100	/* Enable SERR */
+#define  PCI_COMMAND_FAST_BACK	0x200	/* Enable back-to-back writes */
+#define  PCI_COMMAND_INTX_DISABLE 0x400 /* INTx Emulation Disable */
 #define PCI_STATUS              0x06    /* 16 bits */
 #define PCI_REVISION_ID         0x08    /* 8 bits  */
 #define PCI_CLASS_PROG		0x09	/* Reg. Level Programming Interface */
@@ -119,16 +127,30 @@ typedef struct PCIIORegion {
 #define PCI_PRIMARY_BUS		0x18	/* Primary bus number */
 #define PCI_SECONDARY_BUS	0x19	/* Secondary bus number */
 #define PCI_SUBORDINATE_BUS	0x1a	/* Highest bus number behind the bridge */
+#define PCI_SEC_LATENCY_TIMER   0x1b    /* Latency timer for secondary interface */
+#define PCI_IO_BASE             0x1c    /* I/O range behind the bridge */
+#define PCI_IO_LIMIT            0x1d
+#define  PCI_IO_RANGE_MASK      (~0x0fUL)
 #define PCI_SEC_STATUS		0x1e	/* Secondary status register, only bit 14 used */
+#define PCI_MEMORY_BASE         0x20    /* Memory range behind */
+#define PCI_MEMORY_LIMIT        0x22
+#define  PCI_MEMORY_RANGE_MASK  (~0x0fUL)
+#define PCI_PREF_MEMORY_BASE    0x24    /* Prefetchable memory range behind */
+#define PCI_PREF_MEMORY_LIMIT   0x26
+#define  PCI_PREF_RANGE_MASK    (~0x0fUL)
+#define PCI_PREF_BASE_UPPER32   0x28    /* Upper half of prefetchable memory range */
 #define PCI_SUBSYSTEM_VENDOR_ID 0x2c    /* 16 bits */
 #define PCI_SUBSYSTEM_ID        0x2e    /* 16 bits */
 #define PCI_ROM_ADDRESS		0x30	/* Bits 31..11 are address, 10..1 reserved */
 #define  PCI_ROM_ADDRESS_ENABLE	0x01
+#define PCI_IO_BASE_UPPER16     0x30    /* Upper half of I/O addresses */
+#define PCI_IO_LIMIT_UPPER16    0x32
 #define PCI_CAPABILITY_LIST	0x34	/* Offset of first capability list entry */
 #define PCI_ROM_ADDRESS1	0x38	/* Same as PCI_ROM_ADDRESS, but for htype 1 */
 #define PCI_INTERRUPT_LINE	0x3c	/* 8 bits */
 #define PCI_INTERRUPT_PIN	0x3d	/* 8 bits */
 #define PCI_MIN_GNT		0x3e	/* 8 bits */
+#define PCI_BRIDGE_CONTROL      0x3e
 #define PCI_MAX_LAT		0x3f	/* 8 bits */
 
 /* Capability lists */
@@ -358,6 +380,13 @@ typedef struct {
     PCIConfigReadFunc *config_read;
     PCIConfigWriteFunc *config_write;
 
+    /* pci config header type */
+    uint8_t header_type;        /* this is necessary for initialization
+                                 * code to know its header type before
+                                 * device specific code can initialize
+                                 * configuration space.
+                                 */
+
     /* pcie stuff */
     int is_express;   /* is this device pci express?
                        * initialization code needs to know this before