1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
|
# CJDNS support in Bitcoin Core
It is possible to run Bitcoin Core over CJDNS, an encrypted IPv6 network that
uses public-key cryptography for address allocation and a distributed hash table
for routing.
## What is CJDNS?
CJDNS is like a distributed, shared VPN with multiple entry points where every
participant can reach any other participant. All participants use addresses from
the `fc00::/8` network (reserved IPv6 range). Installation and configuration is
done outside of Bitcoin Core, similarly to a VPN (either in the host/OS or on
the network router). See https://github.com/cjdelisle/cjdns#readme and
https://github.com/hyperboria/docs#hyperboriadocs for more information.
Compared to IPv4/IPv6, CJDNS provides end-to-end encryption and protects nodes
from traffic analysis and filtering.
Used with Tor and I2P, CJDNS is a complementary option that can enhance network
redundancy and robustness for both the Bitcoin network and individual nodes.
Each network has different characteristics. For instance, Tor is widely used but
somewhat centralized. I2P connections have a source address and I2P is slow.
CJDNS is fast but does not hide the sender and the recipient from intermediate
routers.
## Installing CJDNS and finding a peer to connect to the network
To install and set up CJDNS, follow the instructions at
https://github.com/cjdelisle/cjdns#how-to-install-cjdns.
You need to initiate an outbound connection to a peer on the CJDNS network
before it will work with your Bitcoin Core node. This is described in steps
["2. Find a friend"](https://github.com/cjdelisle/cjdns#2-find-a-friend) and
["3. Connect your node to your friend's
node"](https://github.com/cjdelisle/cjdns#3-connect-your-node-to-your-friends-node)
in the CJDNS documentation.
One quick way to accomplish these two steps is to query for available public
peers on [Hyperboria](https://github.com/hyperboria) by running the following:
```
git clone https://github.com/hyperboria/peers hyperboria-peers
cd hyperboria-peers
./testAvailable.py
```
For each peer, the `./testAvailable.py` script prints the filename of the peer's
credentials followed by the ping result.
Choose one or several peers, copy their credentials from their respective files,
paste them into the relevant IPv4 or IPv6 "connectTo" JSON object in the
`cjdroute.conf` file you created in step ["1. Generate a new configuration
file"](https://github.com/cjdelisle/cjdns#1-generate-a-new-configuration-file),
and save the file.
## Launching CJDNS
Typically, CJDNS might be launched from its directory with
`sudo ./cjdroute < cjdroute.conf` and it sheds permissions after setting up the
[TUN](https://en.wikipedia.org/wiki/TUN/TAP) interface. You may also [launch it as an
unprivileged user](https://github.com/cjdelisle/cjdns/blob/master/doc/non-root-user.md)
with some additional setup.
The network connection can be checked by running `./tools/peerStats` from the
CJDNS directory.
## Run Bitcoin Core with CJDNS
Once you are connected to the CJDNS network, the following Bitcoin Core
configuration option makes CJDNS peers automatically reachable:
```
-cjdnsreachable
```
When enabled, this option tells Bitcoin Core that it is running in an
environment where a connection to an `fc00::/8` address will be to the CJDNS
network instead of to an [RFC4193](https://datatracker.ietf.org/doc/html/rfc4193)
IPv6 local network. This helps Bitcoin Core perform better address management:
- Your node can consider incoming `fc00::/8` connections to be from the CJDNS
network rather than from an IPv6 private one.
- If one of your node's local addresses is `fc00::/8`, then it can choose to
gossip that address to peers.
## Additional configuration options related to CJDNS
```
-onlynet=cjdns
```
Make automatic outbound connections only to CJDNS addresses. Inbound and manual
connections are not affected by this option. It can be specified multiple times
to allow multiple networks, e.g. onlynet=cjdns, onlynet=i2p, onlynet=onion.
CJDNS support was added to Bitcoin Core in version 23.0 and there may be fewer
CJDNS peers than Tor or IP ones. You can use `bitcoin-cli -addrinfo` to see the
number of CJDNS addresses known to your node.
In general, a node can be run with both an onion service and CJDNS (or any/all
of IPv4/IPv6/onion/I2P/CJDNS), which can provide a potential fallback if one of
the networks has issues. There are a number of ways to configure this; see
[doc/tor.md](https://github.com/bitcoin/bitcoin/blob/master/doc/tor.md) for
details.
## CJDNS-related information in Bitcoin Core
There are several ways to see your CJDNS address in Bitcoin Core:
- in the "Local addresses" output of CLI `-netinfo`
- in the "localaddresses" output of RPC `getnetworkinfo`
To see which CJDNS peers your node is connected to, use `bitcoin-cli -netinfo 4`
or the `getpeerinfo` RPC (i.e. `bitcoin-cli getpeerinfo`).
To see which CJDNS addresses your node knows, use the `getnodeaddresses 0 cjdns`
RPC.
|
