diff options
Diffstat (limited to 'src/wallet')
| -rw-r--r-- | src/wallet/init.cpp | 8 | ||||
| -rw-r--r-- | src/wallet/rpcwallet.cpp | 4 |
2 files changed, 6 insertions, 6 deletions
diff --git a/src/wallet/init.cpp b/src/wallet/init.cpp index 0dc220b6fd..632aae87c9 100644 --- a/src/wallet/init.cpp +++ b/src/wallet/init.cpp @@ -46,19 +46,19 @@ void WalletInit::AddWalletOptions(ArgsManager& argsman) const argsman.AddArg("-avoidpartialspends", strprintf("Group outputs by address, selecting all or none, instead of selecting on a per-output basis. Privacy is improved as an address is only used once (unless someone sends to it after spending from it), but may result in slightly higher fees as suboptimal coin selection may result due to the added limitation (default: %u (always enabled for wallets with \"avoid_reuse\" enabled))", DEFAULT_AVOIDPARTIALSPENDS), ArgsManager::ALLOW_ANY, OptionsCategory::WALLET); argsman.AddArg("-changetype", "What type of change to use (\"legacy\", \"p2sh-segwit\", or \"bech32\"). Default is same as -addresstype, except when -addresstype=p2sh-segwit a native segwit output is used when sending to a native segwit address)", ArgsManager::ALLOW_ANY, OptionsCategory::WALLET); argsman.AddArg("-disablewallet", "Do not load the wallet and disable wallet RPC calls", ArgsManager::ALLOW_ANY, OptionsCategory::WALLET); - argsman.AddArg("-discardfee=<amt>", strprintf("The fee rate (in %s/kB) that indicates your tolerance for discarding change by adding it to the fee (default: %s). " + argsman.AddArg("-discardfee=<amt>", strprintf("The fee rate (in %s/kvB) that indicates your tolerance for discarding change by adding it to the fee (default: %s). " "Note: An output is discarded if it is dust at this rate, but we will always discard up to the dust relay fee and a discard fee above that is limited by the fee estimate for the longest target", CURRENCY_UNIT, FormatMoney(DEFAULT_DISCARD_FEE)), ArgsManager::ALLOW_ANY, OptionsCategory::WALLET); - argsman.AddArg("-fallbackfee=<amt>", strprintf("A fee rate (in %s/kB) that will be used when fee estimation has insufficient data. 0 to entirely disable the fallbackfee feature. (default: %s)", + argsman.AddArg("-fallbackfee=<amt>", strprintf("A fee rate (in %s/kvB) that will be used when fee estimation has insufficient data. 0 to entirely disable the fallbackfee feature. (default: %s)", CURRENCY_UNIT, FormatMoney(DEFAULT_FALLBACK_FEE)), ArgsManager::ALLOW_ANY, OptionsCategory::WALLET); argsman.AddArg("-keypool=<n>", strprintf("Set key pool size to <n> (default: %u). Warning: Smaller sizes may increase the risk of losing funds when restoring from an old backup, if none of the addresses in the original keypool have been used.", DEFAULT_KEYPOOL_SIZE), ArgsManager::ALLOW_ANY, OptionsCategory::WALLET); argsman.AddArg("-maxapsfee=<n>", strprintf("Spend up to this amount in additional (absolute) fees (in %s) if it allows the use of partial spend avoidance (default: %s)", CURRENCY_UNIT, FormatMoney(DEFAULT_MAX_AVOIDPARTIALSPEND_FEE)), ArgsManager::ALLOW_ANY, OptionsCategory::WALLET); argsman.AddArg("-maxtxfee=<amt>", strprintf("Maximum total fees (in %s) to use in a single wallet transaction; setting this too low may abort large transactions (default: %s)", CURRENCY_UNIT, FormatMoney(DEFAULT_TRANSACTION_MAXFEE)), ArgsManager::ALLOW_ANY, OptionsCategory::DEBUG_TEST); - argsman.AddArg("-mintxfee=<amt>", strprintf("Fees (in %s/kB) smaller than this are considered zero fee for transaction creation (default: %s)", + argsman.AddArg("-mintxfee=<amt>", strprintf("Fee rates (in %s/kvB) smaller than this are considered zero fee for transaction creation (default: %s)", CURRENCY_UNIT, FormatMoney(DEFAULT_TRANSACTION_MINFEE)), ArgsManager::ALLOW_ANY, OptionsCategory::WALLET); - argsman.AddArg("-paytxfee=<amt>", strprintf("Fee (in %s/kB) to add to transactions you send (default: %s)", + argsman.AddArg("-paytxfee=<amt>", strprintf("Fee rate (in %s/kvB) to add to transactions you send (default: %s)", CURRENCY_UNIT, FormatMoney(CFeeRate{DEFAULT_PAY_TX_FEE}.GetFeePerK())), ArgsManager::ALLOW_ANY, OptionsCategory::WALLET); argsman.AddArg("-rescan", "Rescan the block chain for missing wallet transactions on startup", ArgsManager::ALLOW_ANY, OptionsCategory::WALLET); #ifdef ENABLE_EXTERNAL_SIGNER diff --git a/src/wallet/rpcwallet.cpp b/src/wallet/rpcwallet.cpp index 7062be6a48..5567d183b6 100644 --- a/src/wallet/rpcwallet.cpp +++ b/src/wallet/rpcwallet.cpp @@ -2293,10 +2293,10 @@ static RPCHelpMan listlockunspent() static RPCHelpMan settxfee() { return RPCHelpMan{"settxfee", - "\nSet the transaction fee per kB for this wallet. Overrides the global -paytxfee command line parameter.\n" + "\nSet the transaction fee rate in " + CURRENCY_UNIT + "/kvB for this wallet. Overrides the global -paytxfee command line parameter.\n" "Can be deactivated by passing 0 as the fee. In that case automatic fee selection will be used by default.\n", { - {"amount", RPCArg::Type::AMOUNT, RPCArg::Optional::NO, "The transaction fee in " + CURRENCY_UNIT + "/kvB"}, + {"amount", RPCArg::Type::AMOUNT, RPCArg::Optional::NO, "The transaction fee rate in " + CURRENCY_UNIT + "/kvB"}, }, RPCResult{ RPCResult::Type::BOOL, "", "Returns true if successful" |