From e7493b25c0b3aa7f2e99d1f0d73b29d8f2528be0 Mon Sep 17 00:00:00 2001 From: Stefan Weil Date: Tue, 2 Mar 2010 22:37:59 +0100 Subject: eepro100: Remove C++ comments C++ comments are unwanted, so this is fixed here. * Replace C++ comments by C comments. * Put code which was deactivated by a C++ comment in #if 0...#endif. Signed-off-by: Stefan Weil Signed-off-by: Michael S. Tsirkin --- hw/eepro100.c | 185 +++++++++++++++++++++++++++++++++++++++------------------- 1 file changed, 126 insertions(+), 59 deletions(-) diff --git a/hw/eepro100.c b/hw/eepro100.c index 0f07b702e4..43a9060254 100644 --- a/hw/eepro100.c +++ b/hw/eepro100.c @@ -154,11 +154,13 @@ typedef struct { uint16_t tcb_bytes; /* transmit command block byte count (in lower 14 bits */ uint8_t tx_threshold; /* transmit threshold */ uint8_t tbd_count; /* TBD number */ - //~ /* This constitutes two "TBD" entries: hdr and data */ - //~ uint32_t tx_buf_addr0; /* void *, header of frame to be transmitted. */ - //~ int32_t tx_buf_size0; /* Length of Tx hdr. */ - //~ uint32_t tx_buf_addr1; /* void *, data to be transmitted. */ - //~ int32_t tx_buf_size1; /* Length of Tx data. */ +#if 0 + /* This constitutes two "TBD" entries: hdr and data */ + uint32_t tx_buf_addr0; /* void *, header of frame to be transmitted. */ + int32_t tx_buf_size0; /* Length of Tx hdr. */ + uint32_t tx_buf_addr1; /* void *, data to be transmitted. */ + int32_t tx_buf_size1; /* Length of Tx data. */ +#endif } eepro100_tx_t; /* Receive frame descriptor. */ @@ -398,7 +400,9 @@ static void eepro100_interrupt(EEPRO100State * s, uint8_t status) s->mem[SCBAck] |= status; status = s->scb_stat = s->mem[SCBAck]; status &= (mask | 0x0f); - //~ status &= (~s->mem[SCBIntmask] | 0x0xf); +#if 0 + status &= (~s->mem[SCBIntmask] | 0x0xf); +#endif if (status && (mask & 0x01)) { /* SCB mask and SCB Bit M do not disable interrupt. */ enable_interrupt(s); @@ -477,9 +481,11 @@ static void pci_reset(EEPRO100State * s) pci_config_set_class(pci_conf, PCI_CLASS_NETWORK_ETHERNET); /* PCI Cache Line Size */ /* check cache line size!!! */ - //~ PCI_CONFIG_8(0x0c, 0x00); +#if 0 + PCI_CONFIG_8(0x0c, 0x00); +#endif /* PCI Latency Timer */ - PCI_CONFIG_8(PCI_LATENCY_TIMER, 0x20); // latency timer = 32 clocks + PCI_CONFIG_8(PCI_LATENCY_TIMER, 0x20); /* latency timer = 32 clocks */ /* PCI Header Type */ /* BIST (built-in self test) */ /* Expansion ROM Base Address (depends on boot disable!!!) */ @@ -492,7 +498,7 @@ static void pci_reset(EEPRO100State * s) /* Interrupt Line */ /* Interrupt Pin */ /* TODO: RST# value should be 0 */ - PCI_CONFIG_8(PCI_INTERRUPT_PIN, 1); // interrupt pin 0 + PCI_CONFIG_8(PCI_INTERRUPT_PIN, 1); /* interrupt pin 0 */ /* Minimum Grant */ PCI_CONFIG_8(PCI_MIN_GNT, 0x08); /* Maximum Latency */ @@ -500,20 +506,20 @@ static void pci_reset(EEPRO100State * s) switch (device) { case i82550: - // TODO: check device id. + /* TODO: check device id. */ pci_config_set_device_id(pci_conf, PCI_DEVICE_ID_INTEL_82551IT); /* Revision ID: 0x0c, 0x0d, 0x0e. */ PCI_CONFIG_8(PCI_REVISION_ID, 0x0e); - // TODO: check size of statistical counters. + /* TODO: check size of statistical counters. */ s->stats_size = 80; - // TODO: check extended tcb support. + /* TODO: check extended tcb support. */ s->has_extended_tcb_support = 1; break; case i82551: pci_config_set_device_id(pci_conf, PCI_DEVICE_ID_INTEL_82551IT); /* Revision ID: 0x0f, 0x10. */ PCI_CONFIG_8(PCI_REVISION_ID, 0x0f); - // TODO: check size of statistical counters. + /* TODO: check size of statistical counters. */ s->stats_size = 80; s->has_extended_tcb_support = 1; break; @@ -572,7 +578,7 @@ static void pci_reset(EEPRO100State * s) PCI_CONFIG_16(PCI_STATUS, PCI_STATUS_DEVSEL_MEDIUM | PCI_STATUS_FAST_BACK | PCI_STATUS_CAP_LIST); PCI_CONFIG_8(PCI_REVISION_ID, 0x08); - // TODO: Windows wants revision id 0x0c. + /* TODO: Windows wants revision id 0x0c. */ PCI_CONFIG_8(PCI_REVISION_ID, 0x0c); #if EEPROM_SIZE > 0 PCI_CONFIG_16(PCI_SUBSYSTEM_VENDOR_ID, 0x8086); @@ -590,7 +596,7 @@ static void pci_reset(EEPRO100State * s) s->has_extended_tcb_support = 1; break; case i82562: - // TODO: check device id. + /* TODO: check device id. */ pci_config_set_device_id(pci_conf, PCI_DEVICE_ID_INTEL_82551IT); /* TODO: wrong revision id. */ PCI_CONFIG_8(PCI_REVISION_ID, 0x0e); @@ -637,14 +643,16 @@ static void pci_reset(EEPRO100State * s) #if EEPROM_SIZE > 0 if (device == i82557C || device == i82558B || device == i82559C) { - // TODO: get vendor id from EEPROM for i82557C or later. - // TODO: get device id from EEPROM for i82557C or later. - // TODO: status bit 4 can be disabled by EEPROM for i82558, i82559. - // TODO: header type is determined by EEPROM for i82559. - // TODO: get subsystem id from EEPROM for i82557C or later. - // TODO: get subsystem vendor id from EEPROM for i82557C or later. - // TODO: exp. rom baddr depends on a bit in EEPROM for i82558 or later. - // TODO: capability pointer depends on EEPROM for i82558. + /* + TODO: get vendor id from EEPROM for i82557C or later. + TODO: get device id from EEPROM for i82557C or later. + TODO: status bit 4 can be disabled by EEPROM for i82558, i82559. + TODO: header type is determined by EEPROM for i82559. + TODO: get subsystem id from EEPROM for i82557C or later. + TODO: get subsystem vendor id from EEPROM for i82557C or later. + TODO: exp. rom baddr depends on a bit in EEPROM for i82558 or later. + TODO: capability pointer depends on EEPROM for i82558. + */ logout("Get device id and revision from EEPROM!!!\n"); } #endif /* EEPROM_SIZE > 0 */ @@ -654,7 +662,9 @@ static void nic_selective_reset(EEPRO100State * s) { size_t i; uint16_t *eeprom_contents = eeprom93xx_data(s->eeprom); - //~ eeprom93xx_reset(s->eeprom); +#if 0 + eeprom93xx_reset(s->eeprom); +#endif memcpy(eeprom_contents, s->conf.macaddr.a, 6); eeprom_contents[EEPROM_ID] = EEPROM_ID_VALID; if (s->device == i82557B || s->device == i82557C) @@ -738,7 +748,7 @@ static void eepro100_write_status(EEPRO100State * s, uint16_t val) static uint16_t eepro100_read_command(EEPRO100State * s) { uint16_t val = 0xffff; - //~ TRACE(OTHER, logout("val=0x%04x\n", val)); + TRACE(OTHER, logout("val=0x%04x\n", val)); return val; } #endif @@ -793,9 +803,11 @@ static void dump_statistics(EEPRO100State * s) stl_le_phys(s->statsaddr + 36, s->statistics.rx_good_frames); stl_le_phys(s->statsaddr + 48, s->statistics.rx_resource_errors); stl_le_phys(s->statsaddr + 60, s->statistics.rx_short_frame_errors); - //~ stw_le_phys(s->statsaddr + 76, s->statistics.xmt_tco_frames); - //~ stw_le_phys(s->statsaddr + 78, s->statistics.rcv_tco_frames); - //~ missing("CU dump statistical counters"); +#if 0 + stw_le_phys(s->statsaddr + 76, s->statistics.xmt_tco_frames); + stw_le_phys(s->statsaddr + 78, s->statistics.rcv_tco_frames); + missing("CU dump statistical counters"); +#endif } static void read_cb(EEPRO100State *s) @@ -832,7 +844,9 @@ static void tx_command(EEPRO100State *s) while (size < tcb_bytes) { uint32_t tx_buffer_address = ldl_phys(tbd_address); uint16_t tx_buffer_size = lduw_phys(tbd_address + 4); - //~ uint16_t tx_buffer_el = lduw_phys(tbd_address + 6); +#if 0 + uint16_t tx_buffer_el = lduw_phys(tbd_address + 6); +#endif tbd_address += 8; TRACE(RXTX, logout ("TBD (simplified mode): buffer address 0x%08x, size 0x%04x\n", @@ -889,7 +903,9 @@ static void tx_command(EEPRO100State *s) s->statistics.tx_good_frames++; /* Transmit with bad status would raise an CX/TNO interrupt. * (82557 only). Emulation never has bad status. */ - //~ eepro100_cx_interrupt(s); +#if 0 + eepro100_cx_interrupt(s); +#endif } static void set_multicast_list(EEPRO100State *s) @@ -1016,7 +1032,9 @@ static void eepro100_cu_command(EEPRO100State * s, uint8_t val) logout("bad CU resume from CU state %u\n", get_cu_state(s)); /* Workaround for bad Linux eepro100 driver which resumes * from idle state. */ - //~ missing("cu resume"); +#if 0 + missing("cu resume"); +#endif set_cu_state(s, cu_suspended); } if (get_cu_state(s) == cu_suspended) { @@ -1067,7 +1085,9 @@ static void eepro100_ru_command(EEPRO100State * s, uint8_t val) /* RU start. */ if (get_ru_state(s) != ru_idle) { logout("RU state is %u, should be %u\n", get_ru_state(s), ru_idle); - //~ assert(!"wrong RU state"); +#if 0 + assert(!"wrong RU state"); +#endif } set_ru_state(s, ru_ready); s->ru_offset = s->pointer; @@ -1078,7 +1098,9 @@ static void eepro100_ru_command(EEPRO100State * s, uint8_t val) if (get_ru_state(s) != ru_suspended) { logout("RU state is %u, should be %u\n", get_ru_state(s), ru_suspended); - //~ assert(!"wrong RU state"); +#if 0 + assert(!"wrong RU state"); +#endif } set_ru_state(s, ru_ready); break; @@ -1140,7 +1162,9 @@ static void eepro100_write_eeprom(eeprom_t * eeprom, uint8_t val) TRACE(EEPROM, logout("val=0x%02x\n", val)); /* mask unwriteable bits */ - //~ val = SET_MASKED(val, 0x31, eeprom->value); +#if 0 + val = SET_MASKED(val, 0x31, eeprom->value); +#endif int eecs = ((val & EEPROM_CS) != 0); int eesk = ((val & EEPROM_SK) != 0); @@ -1222,7 +1246,9 @@ static void eepro100_write_mdi(EEPRO100State * s, uint32_t val) val, raiseint, mdi_op_name[opcode], phy, reg2name(reg), data)); if (phy != 1) { /* Unsupported PHY address. */ - //~ logout("phy must be 1 but is %u\n", phy); +#if 0 + logout("phy must be 1 but is %u\n", phy); +#endif data = 0; } else if (opcode != 1 && opcode != 2) { /* Unsupported opcode. */ @@ -1368,16 +1394,22 @@ static uint8_t eepro100_read1(EEPRO100State * s, uint32_t addr) switch (addr) { case SCBStatus: - //~ val = eepro100_read_status(s); +#if 0 + val = eepro100_read_status(s); +#endif TRACE(OTHER, logout("addr=%s val=0x%02x\n", regname(addr), val)); break; case SCBAck: - //~ val = eepro100_read_status(s); +#if 0 + val = eepro100_read_status(s); +#endif TRACE(OTHER, logout("addr=%s val=0x%02x\n", regname(addr), val)); break; case SCBCmd: TRACE(OTHER, logout("addr=%s val=0x%02x\n", regname(addr), val)); - //~ val = eepro100_read_command(s); +#if 0 + val = eepro100_read_command(s); +#endif break; case SCBIntmask: TRACE(OTHER, logout("addr=%s val=0x%02x\n", regname(addr), val)); @@ -1413,7 +1445,9 @@ static uint16_t eepro100_read2(EEPRO100State * s, uint32_t addr) switch (addr) { case SCBStatus: - //~ val = eepro100_read_status(s); +#if 0 + val = eepro100_read_status(s); +#endif case SCBCmd: TRACE(OTHER, logout("addr=%s val=0x%04x\n", regname(addr), val)); break; @@ -1437,11 +1471,15 @@ static uint32_t eepro100_read4(EEPRO100State * s, uint32_t addr) switch (addr) { case SCBStatus: - //~ val = eepro100_read_status(s); +#if 0 + val = eepro100_read_status(s); +#endif TRACE(OTHER, logout("addr=%s val=0x%08x\n", regname(addr), val)); break; case SCBPointer: - //~ val = eepro100_read_pointer(s); +#if 0 + val = eepro100_read_pointer(s); +#endif TRACE(OTHER, logout("addr=%s val=0x%08x\n", regname(addr), val)); break; case SCBPort: @@ -1468,7 +1506,9 @@ static void eepro100_write1(EEPRO100State * s, uint32_t addr, uint8_t val) switch (addr) { case SCBStatus: - //~ eepro100_write_status(s, val); +#if 0 + eepro100_write_status(s, val); +#endif break; case SCBAck: eepro100_acknowledge(s); @@ -1508,7 +1548,9 @@ static void eepro100_write2(EEPRO100State * s, uint32_t addr, uint16_t val) switch (addr) { case SCBStatus: - //~ eepro100_write_status(s, val); +#if 0 + eepro100_write_status(s, val); +#endif eepro100_acknowledge(s); break; case SCBCmd: @@ -1556,7 +1598,9 @@ static void eepro100_write4(EEPRO100State * s, uint32_t addr, uint32_t val) static uint32_t ioport_read1(void *opaque, uint32_t addr) { EEPRO100State *s = opaque; - //~ logout("addr=%s\n", regname(addr)); +#if 0 + logout("addr=%s\n", regname(addr)); +#endif return eepro100_read1(s, addr - s->region[1]); } @@ -1575,7 +1619,9 @@ static uint32_t ioport_read4(void *opaque, uint32_t addr) static void ioport_write1(void *opaque, uint32_t addr, uint32_t val) { EEPRO100State *s = opaque; - //~ logout("addr=%s val=0x%02x\n", regname(addr), val); +#if 0 + logout("addr=%s val=0x%02x\n", regname(addr), val); +#endif eepro100_write1(s, addr - s->region[1], val); } @@ -1623,42 +1669,54 @@ static void pci_map(PCIDevice * pci_dev, int region_num, static void pci_mmio_writeb(void *opaque, target_phys_addr_t addr, uint32_t val) { EEPRO100State *s = opaque; - //~ logout("addr=%s val=0x%02x\n", regname(addr), val); +#if 0 + logout("addr=%s val=0x%02x\n", regname(addr), val); +#endif eepro100_write1(s, addr, val); } static void pci_mmio_writew(void *opaque, target_phys_addr_t addr, uint32_t val) { EEPRO100State *s = opaque; - //~ logout("addr=%s val=0x%02x\n", regname(addr), val); +#if 0 + logout("addr=%s val=0x%02x\n", regname(addr), val); +#endif eepro100_write2(s, addr, val); } static void pci_mmio_writel(void *opaque, target_phys_addr_t addr, uint32_t val) { EEPRO100State *s = opaque; - //~ logout("addr=%s val=0x%02x\n", regname(addr), val); +#if 0 + logout("addr=%s val=0x%02x\n", regname(addr), val); +#endif eepro100_write4(s, addr, val); } static uint32_t pci_mmio_readb(void *opaque, target_phys_addr_t addr) { EEPRO100State *s = opaque; - //~ logout("addr=%s\n", regname(addr)); +#if 0 + logout("addr=%s\n", regname(addr)); +#endif return eepro100_read1(s, addr); } static uint32_t pci_mmio_readw(void *opaque, target_phys_addr_t addr) { EEPRO100State *s = opaque; - //~ logout("addr=%s\n", regname(addr)); +#if 0 + logout("addr=%s\n", regname(addr)); +#endif return eepro100_read2(s, addr); } static uint32_t pci_mmio_readl(void *opaque, target_phys_addr_t addr) { EEPRO100State *s = opaque; - //~ logout("addr=%s\n", regname(addr)); +#if 0 + logout("addr=%s\n", regname(addr)); +#endif return eepro100_read4(s, addr); } @@ -1695,7 +1753,9 @@ static int nic_can_receive(VLANClientState *nc) EEPRO100State *s = DO_UPCAST(NICState, nc, nc)->opaque; TRACE(RXTX, logout("%p\n", s)); return get_ru_state(s) == ru_ready; - //~ return !eepro100_buffer_full(s); +#if 0 + return !eepro100_buffer_full(s); +#endif } static ssize_t nic_receive(VLANClientState *nc, const uint8_t * buf, size_t size) @@ -1724,13 +1784,15 @@ static ssize_t nic_receive(VLANClientState *nc, const uint8_t * buf, size_t size * Short frame is discarded */ logout("%p received short frame (%zu byte)\n", s, size); s->statistics.rx_short_frame_errors++; - //~ return -1; +#if 0 + return -1; +#endif } else if ((size > MAX_ETH_FRAME_SIZE + 4) && !(s->configuration[18] & BIT(3))) { /* Long frame and configuration byte 18/3 (long receive ok) not set: * Long frames are discarded. */ logout("%p received long frame (%zu byte), ignored\n", s, size); return -1; - } else if (memcmp(buf, s->conf.macaddr.a, 6) == 0) { // !!! + } else if (memcmp(buf, s->conf.macaddr.a, 6) == 0) { /* !!! */ /* Frame matches individual address. */ /* TODO: check configuration byte 15/4 (ignore U/L). */ TRACE(RXTX, logout("%p received frame for me, len=%zu\n", s, size)); @@ -1774,11 +1836,12 @@ static ssize_t nic_receive(VLANClientState *nc, const uint8_t * buf, size_t size /* TODO: RNR interrupt only at first failed frame? */ eepro100_rnr_interrupt(s); s->statistics.rx_resource_errors++; - //~ assert(!"no resources"); +#if 0 + assert(!"no resources"); +#endif return -1; } - //~ !!! -//~ $3 = {status = 0x0, command = 0xc000, link = 0x2d220, rx_buf_addr = 0x207dc, count = 0x0, size = 0x5f8, packet = {0x0 }} + /* !!! */ eepro100_rx_t rx; cpu_physical_memory_read(s->ru_base + s->ru_offset, (uint8_t *) & rx, offsetof(eepro100_rx_t, packet)); @@ -1799,14 +1862,18 @@ static ssize_t nic_receive(VLANClientState *nc, const uint8_t * buf, size_t size rfd_status); stw_phys(s->ru_base + s->ru_offset + offsetof(eepro100_rx_t, count), size); /* Early receive interrupt not supported. */ - //~ eepro100_er_interrupt(s); +#if 0 + eepro100_er_interrupt(s); +#endif /* Receive CRC Transfer not supported. */ if (s->configuration[18] & BIT(2)) { missing("Receive CRC Transfer"); return -1; } /* TODO: check stripping enable bit. */ - //~ assert(!(s->configuration[17] & BIT(0))); +#if 0 + assert(!(s->configuration[17] & BIT(0))); +#endif cpu_physical_memory_write(s->ru_base + s->ru_offset + offsetof(eepro100_rx_t, packet), buf, size); s->statistics.rx_good_frames++; -- cgit v1.2.3