| Age | Commit message (Collapse) | Author |
|---|
|
The pending register upper limit is currently set to
plic->num_sources >> 3, which is wrong, e.g.: considering
plic->num_sources is 7, the upper limit becomes 0 which fails
the range check if reading the pending register at pending_base.
Fixes: 1e24429e40df ("SiFive RISC-V PLIC Block")
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-16-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
At present the SiFive PLIC model "priority-base" expects interrupt
priority register base starting from source 1 instead source 0,
that's why on most platforms "priority-base" is set to 0x04 except
'opentitan' machine. 'opentitan' should have set "priority-base"
to 0x04 too.
Note the irq number calculation in sifive_plic_{read,write} is
correct as the codes make up for the irq number by adding 1.
Let's simply update "priority-base" to start from interrupt source
0 and add a comment to make it crystal clear.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Message-Id: <20221211030829.802437-14-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
At present the default value of "num-sources" property is zero,
which does not make a lot of sense, as in sifive_plic_realize()
we see s->bitfield_words is calculated by:
s->bitfield_words = (s->num_sources + 31) >> 5;
if the we don't configure "num-sources" property its default value
zero makes s->bitfield_words zero too, which isn't true because
interrupt source 0 still occupies one word.
Let's change the default value to 1 meaning that only interrupt
source 0 is supported by default and a sanity check in realize().
While we are here, add a comment to describe the exact meaning of
this property that the number should include interrupt source 0.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-9-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
sifive_plic_realize()
The realize() callback has an errp for us to propagate the error up.
While we are here, correct the wrong multi-line comment format.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-Id: <20221211030829.802437-8-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
At present the PLIC config parser can only handle legal config string
like "MS,MS". However if a config string like ",MS,MS,,MS,MS,," is
given the parser won't get the correct configuration.
This commit improves the config parser to make it more robust.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-7-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
H-mode has been removed since priv spec 1.10. Drop it.
Signed-off-by: Bin Meng <bmeng@tinylab.org>
Reviewed-by: Wilfred Mallawa <wilfred.mallawa@wdc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221211030829.802437-6-bmeng@tinylab.org>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
If the number of interrupt is not multiple of 32, PLIC will have
out-of-bound access to source_priority array. Compute the number of
interrupt in the last word to avoid this out-of-bound access of array.
Signed-off-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Bin Meng <bmeng@tinylab.org>
Message-Id: <20221127165753.30533-1-jim.shu@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
Commit 40244040a7a changed the way the S irqs are numbered. This breaks when
using numa configuration, e.g.:
./qemu-system-riscv64 -nographic -machine virt,dumpdtb=numa-tree.dtb \
-m 2G -smp cpus=16 \
-object memory-backend-ram,id=mem0,size=512M \
-object memory-backend-ram,id=mem1,size=512M \
-object memory-backend-ram,id=mem2,size=512M \
-object memory-backend-ram,id=mem3,size=512M \
-numa node,cpus=0-3,memdev=mem0,nodeid=0 \
-numa node,cpus=4-7,memdev=mem1,nodeid=1 \
-numa node,cpus=8-11,memdev=mem2,nodeid=2 \
-numa node,cpus=12-15,memdev=mem3,nodeid=3
leads to:
Unexpected error in object_property_find_err() at ../qom/object.c:1304:
qemu-system-riscv64: Property 'riscv.sifive.plic.unnamed-gpio-out[8]' not
found
This patch makes the nubering of the S irqs identical to what it was before.
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Signed-off-by: Frédéric Pétrot <frederic.petrot@univ-grenoble-alpes.fr>
Message-Id: <20221114135122.1668703-1-frederic.petrot@univ-grenoble-alpes.fr>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
PLIC spec [1] requires interrupt source priority registers are WARL
field and the number of supported priority is power-of-2 to simplify SW
discovery.
Existing QEMU RISC-V machine (e.g. shakti_c) don't strictly follow PLIC
spec, whose number of supported priority is not power-of-2. Just change
each bit of interrupt priority register to WARL field when the number of
supported priority is power-of-2.
[1] https://github.com/riscv/riscv-plic-spec/blob/master/riscv-plic.adoc#interrupt-priorities
Signed-off-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Clément Chigot <chigot@adacore.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221003041440.2320-3-jim.shu@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
The maximum priority level is hard-coded when writing to interrupt
priority register. However, when writing to priority threshold register,
the maximum priority level is from num_priorities Property which is
configured by platform.
Also change interrupt priority register to use num_priorities Property
in maximum priority level.
Signed-off-by: Emmanuel Blot <emmanuel.blot@sifive.com>
Signed-off-by: Jim Shu <jim.shu@sifive.com>
Reviewed-by: Frank Chang <frank.chang@sifive.com>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20221003041440.2320-2-jim.shu@sifive.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
Since commit 40244040a7ac, multi-socket configuration with plic is
broken as the hartid for second socket is calculated incorrectly.
The hartid stored in addr_config already includes the offset
for the base hartid for that socket. Adding it again would lead
to segfault while creating the plic device for the virt machine.
qdev_connect_gpio_out was also invoked with incorrect number of gpio
lines.
Fixes: 40244040a7ac (hw/intc: sifive_plic: Avoid overflowing the addr_config buffer)
Signed-off-by: Atish Patra <atishp@rivosinc.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <20220723090335.671105-1-atishp@rivosinc.com>
[ Changes by AF:
- Change the qdev_connect_gpio_out() numbering
]
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
Since commit ad40be27 "target/riscv: Support start kernel directly by
KVM" we have been overflowing the addr_config on "M,MS..."
configurations, as reported https://gitlab.com/qemu-project/qemu/-/issues/1050.
This commit changes the loop in sifive_plic_create() from iterating over
the number of harts to just iterating over the addr_config. The
addr_config is based on the hart_config, and will contain interrup details
for all harts. This way we can't iterate past the end of addr_config.
Fixes: ad40be27084536 ("target/riscv: Support start kernel directly by KVM")
Resolves: https://gitlab.com/qemu-project/qemu/-/issues/1050
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Mingwang Li <limingwang@huawei.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Message-Id: <20220601013631.196854-1-alistair.francis@opensource.wdc.com>
|
|
Get kernel and fdt start address in virt.c, and pass them to KVM
when cpu reset. Add kvm_riscv.h to place riscv specific interface.
In addition, PLIC is created without M-mode PLIC contexts when KVM
is enabled.
Signed-off-by: Yifei Jiang <jiangyifei@huawei.com>
Signed-off-by: Mingwang Li <limingwang@huawei.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Message-id: 20220112081329.1835-7-jiangyifei@huawei.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
We can remove the original sifive_plic_irqs_pending() function and
instead just use the sifive_plic_claim() function (renamed to
sifive_plic_claimed()) to determine if any interrupts are pending.
This requires move the side effects outside of sifive_plic_claimed(),
but as they are only invoked once that isn't a problem.
We have also removed all of the old #ifdef debugging logs, so let's
cleanup the last remaining debug function while we are here.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220105213937.1113508-5-alistair.francis@opensource.wdc.com>
|
|
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220105213937.1113508-4-alistair.francis@opensource.wdc.com>
|
|
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220105213937.1113508-3-alistair.francis@opensource.wdc.com>
|
|
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-Id: <20220105213937.1113508-2-alistair.francis@opensource.wdc.com>
|
|
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 4200da222a65c89ed1ba35f754dcca7fdd9f08d6.1634524691.git.alistair.francis@wdc.com
|
|
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: b94c098cb221e744683349b1ac794c23102ef471.1634524691.git.alistair.francis@wdc.com
|
|
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 3c125e27c49a4969df82bf8b197535ccd1996939.1634524691.git.alistair.francis@wdc.com
|
|
Instead of using riscv_cpu_update_mip() let's instead use the new RISC-V
CPU GPIO lines to set the external MIP bits.
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Message-id: 0364190bfa935058a845c0fa1ecf650328840ad5.1630301632.git.alistair.francis@wdc.com
|
|
Stop including hw/boards.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-3-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
|
|
Stop including sysemu/sysemu.h in files that don't need it.
Signed-off-by: Thomas Huth <thuth@redhat.com>
Message-Id: <20210416171314.2074665-2-thuth@redhat.com>
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
|
|
Add sifive_plic vmstate for supporting sifive_plic migration.
Current vmstate framework only supports one structure parameter
as num field to describe variable length arrays, so introduce
num_enables.
Signed-off-by: Yifei Jiang <jiangyifei@huawei.com>
Signed-off-by: Yipeng Yin <yinyipeng1@huawei.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20201026115530.304-7-jiangyifei@huawei.com
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
|
clang's C11 atomic_fetch_*() functions only take a C11 atomic type
pointer argument. QEMU uses direct types (int, etc) and this causes a
compiler error when a QEMU code calls these functions in a source file
that also included <stdatomic.h> via a system header file:
$ CC=clang CXX=clang++ ./configure ... && make
../util/async.c:79:17: error: address argument to atomic operation must be a pointer to _Atomic type ('unsigned int *' invalid)
Avoid using atomic_*() names in QEMU's atomic.h since that namespace is
used by <stdatomic.h>. Prefix QEMU's APIs with 'q' so that atomic.h
and <stdatomic.h> can co-exist. I checked /usr/include on my machine and
searched GitHub for existing "qatomic_" users but there seem to be none.
This patch was generated using:
$ git grep -h -o '\<atomic\(64\)\?_[a-z0-9_]\+' include/qemu/atomic.h | \
sort -u >/tmp/changed_identifiers
$ for identifier in $(</tmp/changed_identifiers); do
sed -i "s%\<$identifier\>%q$identifier%g" \
$(git grep -I -l "\<$identifier\>")
done
I manually fixed line-wrap issues and misaligned rST tables.
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Message-Id: <20200923105646.47864-1-stefanha@redhat.com>
|
|
This is an effort to clean up the hw/riscv directory. Ideally it
should only contain the RISC-V SoC / machine codes plus generic
codes. Let's move sifive_plic model to hw/intc directory.
Signed-off-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Alistair Francis <alistair.francis@wdc.com>
Message-Id: <1599129623-68957-7-git-send-email-bmeng.cn@gmail.com>
Signed-off-by: Alistair Francis <alistair.francis@wdc.com>
|
